Vic -Ring Couplings & Adapters
16.06VIC-RING APPLIED RING SYSTEMVic -RingCouplings & AdaptersVictaulic offers the Vic -Ring Piping Method for joining large diameter pipe which does notlend itself to direct grooving. The adaptation of pipe with Vic-Ring adapters and the selectionof a suitable Victaulic coupling can present individual considerations which are best handledby Victaulic engineers, who are experienced in these applications. However, the followingguidelines can be used to aid in the selection process.Type “A”This method is widely used for light wall pipe and tubing for general applications. The Vic-Ring adapters are slipped over the pipe ends and are welded in place with a single fillet end weld. The Victaulic coupling seats over the Vic-Ring adapter and functions in normal fashion.Type “B”A short grooved nipple, butt-welded to the pipe end. The nipples may be cut from standard pipe and joined using standard IPS couplings or withVic‑Ring couplings.Type “C”Attached with double fillet welds, front and rear, this is principally for large diameter pipe. Coupling Styles 41 and 44 are generally applied but othersmay be used depending on the Vic-Ring O.D.Type “D”A heavy duty collar typically for large diameter pipe – 30"/750 mm and up – providing special pipe end reinforcement and rigidity. Styles 41 and 44couplings are most commonly used, however, others may be used depending on the Vic-Ring adapter O.D.Type “E”Similar in application to Type “C” and “D” Vic-Ring adapter ends, Type E allows easier attachment while providing secure coupling engagement.Style 31, Style 41 and Style 44 couplings are commonly used.Type “G”Ductile iron pipe may sometimes be supplied with a cast-in shoulder which equates to an applied ring.The Vic-Ring illustrations (page 2) are of configurations often used for general, non-abrasive, non-corrosive services.Modifications may be necessary for your application. Contact Victaulic with specific requirements for application recommendations, dimensions and technical data.For complete Vic-Ring product, pipe preparation, design and selection details, contact Victaulic.job/ownercontractorengineerSystem No.Submitted BySpec Sect ulic is a registered trademark of Victaulic Company. 2007 Victaulic Company. All rights reserved. printed in the USA.REV B16.06 1
16.06VIC-RING APPLIED RING SYSTEMVic -RingCouplings & AdaptersVIC-RING CONFIGURATIONSStandard Vic-Ring ConfigurationsType “A” Vic-RingType “B” Vic-RingType “C” Vic-RingType “E” Vic-RingType “G” Vic-RingOther Available Configurations(Contact Victaulic for information)Type “D” Vic-RingIllustrations are exaggerated for claritywww.victaulic.comVictaulic is a registered trademark of Victaulic Company. 2007 Victaulic Company. All rights reserved. printed in the USA.16.06 2REV B
16.06VIC-RING APPLIED RING SYSTEMVic -RingCouplings & AdaptersType “A”Vic-Ring Adapter EndsThis method is widely used for adapting common sizes of light wall pipe and tubing for generalapplications such as contractors’ portable pipe lines, irrigation lines, ventilating and duct piping, tanktruck tubing and other applications where weight is a factor. The Vic-Ring adapters are slipped overthe pipe ends and are welded in place with a single fillet end weld. The Victaulic coupling seats overthe Vic-Ring adapter and functions in normal fashion.TYPE “A” VIC-RING ADAPTEROutsideDiameter*Pipe WallThicknessVic-Ring Adapter DimensionsInches/millimetersCoupling DataNominalInchesmmInchesmmRing O.D.C.D.Gasket Seat“A” 0.03 0.76Ring I.D.**MaximumJoint 5034560150022SizeNominalInchesmmStyle*Max pipe O.D. 0.06 for distance 0.75" behind collar.These Vic-Ring adapters are not to be considered as pipe reinforcement. If reinforcement is required, provision must be made by the designer.AThese surfaces must be smooth andfree from scores, seams and projection.WeldRing I.D.Ring O.D.www.victaulic.comVictaulic is a registered trademark of Victaulic Company. 2007 Victaulic Company. All rights reserved. printed in the USA.REV B16.06 3
16.06VIC-RING APPLIED RING SYSTEMVic -RingCouplings & AdaptersType “D”Heavy Duty Grooved Vic-RingAdapter Ends – Double FilletsThis heavy duty type end applies principally to large diameter pipe – 30"/ 750 mm and up. Style 44couplings are most commonly used with Type “D” Vic-Ring adapters; however, others may be useddepending on the Vic-Ring adapter ingO.D.C.D.GasketSeat 508936.1291717512003690044Vic-Ring Adapter Dimensions dth “B”Coupling DataRingWidth“L”Min.Max. Work.Press.psikPaRing I.D.SizeNom.InchesmmStyleThese Vic-Ring adapters are not to be considered as pipe reinforcement. If reinforcement is required,provision must be made by the designer.† Dimensions shown are approximate average dimensions, and should only be used as a general guideline.Table continued on next page.LThis surface must besmooth and free from scores,seams and projections.ABWeldWeldRing I.D.Ring O.D.Cwww.victaulic.comVictaulic is a registered trademark of Victaulic Company. 2007 Victaulic Company. All rights reserved. printed in the USA.16.06 4REV B
16.06VIC-RING APPLIED RING SYSTEMVic -RingCouplings & smmRingO.D.C.D.GasketSeat Vic-Ring Adapter Dimensions dth “B”Coupling DataRingWidth“L”Min.Max. Work.Press.psikPaRing I.D.SizeNom.InchesmmStyleThese Vic-Ring adapters are not to be considered as pipe reinforcement. If reinforcement is required,provision must be made by the designer.† Dimensions shown are approximate average dimensions, and should only be used as a general guideline.LThis surface must besmooth and free from scores,seams and projections.ABWeldWeldRing I.D.Ring O.D.Cwww.victaulic.comVictaulic is a registered trademark of Victaulic Company. 2007 Victaulic Company. All rights reserved. printed in the USA.REV B16.06 5
16.06VIC-RING APPLIED RING SYSTEMVic -RingCouplings & AdaptersType “E”Vic-Ring Adapter Ends –Double FilletsType E is similar in application to “D” Vic-Ring allowing easier attachment while providing securecoupling engagement. Style 31, Style 41 and Style 44 couplings are commonly used with Type “E”Vic-Ring esmmRingO.D.C.D.GasketSeat 0164000.1884.818.50470184500.1884.818450Vic-Ring Adapter Dimensions †Inches/millimetersCoupling DataRing I.D.Max. 59612.636736.1291715010353690031StyleThese Vic-Ring adapters are not to be considered as pipe reinforcement. If reinforcement is required,provision must be made by the designer.† Dimensions shown are approximate average dimensions, and should only be used as a general guideline.Table continued on next page.(Min.)LThese surfaces must be smooth andfree from scores, seams and projections.AWeldRing O.D.WeldCRing I.D.www.victaulic.comVictaulic is a registered trademark of Victaulic Company. 2007 Victaulic Company. All rights reserved. printed in the USA.16.06 6REV B
16.06VIC-RING APPLIED RING SYSTEMVic -RingCouplings & smmRingO.D.C.D.GasketSeat -Ring Adapter Dimensions †Inches/millimetersCoupling DataRing I.D.Max. e Vic-Ring adapters are not to be considered as pipe reinforcement. If reinforcement is required,provision must be made by the designer.† Dimensions shown are approximate average dimensions, and should only be used as a general guideline.(Min.)LThese surfaces must be smooth andfree from scores, seams and projections.AWeldRing O.D.WeldCRing I.D.www.victaulic.comVictaulic is a registered trademark of Victaulic Company. 2007 Victaulic Company. All rights reserved. printed in the USA.REV B16.06 7
16.06VIC-RING APPLIED RING SYSTEMVic -RingCouplings & AdapterswarrantyRefer to the Warranty section of the current Price List or contact Victaulic for details.noteThis product shall be manufactured by Victaulic or to Victaulic specifications. All products to beinstalled in accordance with current Victaulic installation/assembly instructions. Victaulic reserves theright to change product specifications, designs and standard equipment without notice and withoutincurring obligations.WCAS-6WAKT3For complete contact information, visit www.victaulic.com16.061953 rev BUpdated 7/2007Victaulic is a registered trademark of Victaulic Company. 2007 Victaulic Company. All rights reserved. printed in the USA.16.06
Victaulic offers the Vic -Ring Piping Method for joining large diameter pipe which does not lend itself to direct grooving. The adaptation of pipe with Vic-Ring adapters and the selection of a suitable Victaulic coupling can
dust seal mc seal o-ring o-ring teflon o-ring o-ring snap ring dust seal mc seal o-ring o-ring retaining ring o-ring teflon ring o-ring o-ring lock-nut lh o-ring silicone (not shown) o-ring (not shown) 79543 79004 79082 79077 79079 79081 79084 79078 79007 79541 79542 79017 79009 79504 79080
Cave VIC Mac 285 287 572 284 289 573 7 Jarrad Alston VIC Yda 288 286 574 286 285 571 8 Marcus Anear VIC Dva 284 286 570 288 286 574 9 Bryce Lee VIC Dva 290 282 572 288 278 566 10 Larry Kelly VIC Wac 277 285 562 286 289 575 11 Ryan Bickerton VIC Mac 284 280 564 287 283 570 . Rowney VIC Sa 0 0 0 175 195
Voith Turbo Private Limited wae establised in the year 2006 and is a renowned manufacture of couplings of various types. These are widely used in industries. We manufacturers and supplies geared variable speed couplings, variable speed couplings, constant speed couplings, heavy duty couplings, standard couplings etc. For more information .
Coupling Preselection and Options 3 Torsionally Rigid Gear Couplings ZAPEX ZW 4 ZAPEX ZI 5 Torsionally Rigid All-Steel Couplings ARPEX 6 Flexible Couplings N-EUPEX 7 RUPEX 8 BIPEX 9 Highly Flexible Couplings ELPEX-B 10 ELPEX-S 11 ELPEX 12 Fluid Couplings FLUDEX 13 Taper Clamping Bushes 14 Ap
Metal Seal for Banjo Fittings O7 O-Ring Face Seal Port Ends - SAE, Metric, BSPP, JIS, K4 EO/EO-2 EO-2 Sealing Ring O6 EOlastic Seal Ring O5 ISO 6149 O-Ring O4 Metric O-Ring O4 4-Bolt Flanges Metric Retaining Ring O4 JIS B2351 O-Ring O6 PLS Bonded Seal O3 Pressure Gauge Sealing Ring O8 BSPP Retaining Ring O5 BSPP O-Ring O5 EO O-Ring O8 BSPP .
FH Series and F2 Series Eaton / Char-Lynn Motors H Series S Series 2000, 4000, 6000, and 10,000 Series Parker Hannifin Motors TF Series and TG Series PTO Adapters Splined Adapters Round Shaft Adapters Splined Couplings Involuted Splined Couplings Round Bore Couplings Precision Splined Hub
12. O-ring Gland Design Friction In normal applications harder materials provide less friction than softer materi-als. However, the higher the hardness of the O-ring, above 70 Shore A, the greater the friction. This is because the compressive force at the same squeeze, is greater than with softer materials. Compound swell decreases the hard-File Size: 338KBPage Count: 31Explore furtherO-Ring Groove Design Guide & Recommendations allorings.comwww.allorings.comO-Ring Groove Design Guides Engineering Quick Referencewww.marcorubber.comMetric O-Ring Groove Design Reference Guidewww.allorings.comDynamic O-Ring Design Chart Marco Rubber & Plastics .www.marcorubber.comO-ring Design, O-ring Design Guide, O-ring Seal Design .mykin.comRecommended to you b
accounting standards (for domestic filing purposes) and IFRS as issued by the IASB (or other permitted equivalent standards) for the subsidiary, the parent company or the whole group (for the purposes of the EEA listing). We would urge any companies that may be affected by this change to check with the relevant EEA competent authority as soon as possible so that they are clear what .
