Synergy.doc Synergy V Universal / DVR Remote Control
Synergy.docSynergy VUniversal / DVR Remote ControlModel RT-U62CDProgramming And Operating InstructionsRev. 09/04 2004 CONTEC CORPORATION-1-
Synergy.doc1. IntroductionYour Synergy V Universal / DVR remote control is simple to program, easy to use, and can operate up to five (5)electronic devices, which include:CABLETVVCRDVDAUDIOCable set-top terminalsTelevisionsVCRDVDAudio receivers, amplifiers, CD playersBefore you can use your remote control, it must be programmed (set-up) to operate the above devices.2. Before Getting StartedSome of the special features and buttons on your remote control are as follows:Point and Press ProgrammingLets you program your TV, VCR, DVD, AUDIO devices without using codes. For more information, seesections 5 and 14.[ALL] SmartKey Turns your CABLE set-top terminal and TV on / off with one button press. [ALL] can also be programmed toturn on / off additional electronic devices, or automatically set your correct TV output channel. For moreinformation, see section 9.[MODE]Indicates which mode (i.e. CBL, TV, VCR, DVD, AUDIO) the remote is currently operating in by illuminating thepower button. To change to a different mode, press [MODE], then the power button for the electronic deviceyou wish to operate. For more information, see Section 15.Memory Guard Eliminates reprogramming after battery changes.3. Installing / Replacing BatteriesInstall two (2) new AA Alkaline batteries. Properly match the “ / -” ends of the batteries with the diagram in thebattery compartment.When the batteries become low and need to be replaced, the [CBL], [TV], [VCR], [DVD], [AUDIO] buttons will notilluminate normally or at all during use.When this happens, replace the existing batteries with two (2) new AA Alkaline batteries to restore normaloperation to the remote control.4. Programming Your Cable Set-Top TerminalYour remote control is pre-programmed to operate the Motorola 62xx series DVR set-top terminal. Tooperate a different cable set-top terminal, look up the brand and model in the Cable Setup Code list and followthese steps:1. Press [OK], then [MUTE] together until the power / mode buttons illuminate in slow-rotation (i.e.CBL Æ TV Æ VCR Æ DVD Æ AUDIO -- CBL).-2-
Synergy.doc2. From the Cable Setup Code list, locate the 3-digit code for your brand / model and enter it on the keypadof the remote control. The set-top terminal will turn off.3. Then, press [OK] to lock in the code. The power / mode buttons will blink 3-times and go out.Cable Setup CodesMotorolaDCT (all except DVR)CFT 2200DCT – 62xx series DVR terminals001001002JerroldDL4, DP(V), DQN(V), DPBB003Scientific AtlantaExplorer 8000 (SARA - RT-U59C)Explorer 8000 (Passport - RT-U61CP)Explorer 8600X8600412413004005006Pace510 DigitalHD Digital004010Pioneer VoyagerBA-V1000, BA-V2000004007Tocom5503VIP, 5507, 5508008ZenithMM 2500Digital0090135. Programming Your TV, VCR, DVD, and AUDIO DevicesCode-Entry Programming1. Turn on all the electronic devices (TV, VCR, DVD, AUDIO) you want to program the remote to operate.2. Press [OK], then [MUTE] together until the power / mode buttons illuminate in slow-rotation (i.e. CBL ÆTV Æ VCR Æ DVD Æ AUDIO Æ CBL ).3. a. To program your TV, locate the 3-digit code for your brand in the TV Setup Code list and enter it on thekeypad of the remote control. Entry of the correct code will cause your TV to turn off. If multiple codesare listed for your brand, you may have to try several different codes until your TV turns off.b. As soon as you have entered a 3-digit code that turns your TV off, press [MUTE].1. If the TV turns back on, press [OK] to lock in the code. The power / mode buttons will blink 3times and go out.Or2. If the TV does not turn back on, enter a different 3-digit setup code until your TV turns back on.Then press [OK] to lock in the code. The power / mode buttons will blink 3-times and go out.4. To program your VCR, refer to the VCR / DVD Setup Code lists and repeat steps 2 and 3 above.5. To program your DVD, refer to the VCR / DVD Setup Code lists and repeat steps 2 and 3 above.6. To program your AUDIO equipment, refer to the AUDIO Setup Code list and repeat steps 2 and 3 above.-3-
Synergy.docPoint and Press ProgrammingThis method allows you to program the remote control without using codes. Instead, the remote controlautomatically finds the correct command that you select in a variety of codes until you find the code that operatesyour device. You then lock in the correct code as described below.The following instructions describe how to program your remote control using the [CH ] or [CH -] buttons ("Power"function during programming). You may also program your remote control using other buttons / functions asdescribed in Section 14. When using this method, there are several important points to remember: The order in which you program your electronic devices is not important. There may be several codes that turn your electronic devices on / off (or perform other functions). Once youlock-in a code, be sure to check the available functions for that device (i.e. TV - Vol /-, Mute, TV Input(Video Source button); VCR - Play, Stop.; DVD - Play, Stop.; AUDIO - Vol /-, Mute) to see if they areoperating. While the remote is searching for the correct setup code(s) for your electronic devices, it is possible thatother (previously programmed) devices may turn on / off (or perform other functions). If this occurs,continue pressing the [CH ] or [CH -] buttons (or the buttons described in Section 14) until you find thecorrect code for the device you are programming. It may take several minutes for the remote to find the correct code that turns your device off (or performsanother selected function). During this time, the power / mode buttons will illuminate in fast-rotation (i.e.CBL Æ TV Æ VCR Æ DVD Æ AUDIO Æ CBL ).Programming your electronic devices using the [Ch ] or [Ch -] buttons (“Power” function duringprogramming).1. Turn on all the electronic devices (TV, VCR, DVD, AUDIO) you want to program the remote to operate.2. Press [OK], then [MUTE] together until the power / mode buttons illuminate in slow-rotation (i.e. CBL ÆTV Æ VCR Æ DVD Æ AUDIO Æ CBL ).3. Press and hold the [CH ] button until one device turns off. While you are pressing the [CH ] button, thepower / mode buttons will illuminate in fast-rotation. As soon as one device turns off, release the [CH ]button.4. Press [MUTE]. If the device that turned off.a. Turns back on, press [OK] to lock in this code. The power / mode buttons will blink 3-times and goout.Orb. Does not turn back on, press [CH -] one step at a time until that device turns back on. Each time youpress the [CH -] button, the power / mode buttons will illuminate once in reverse fast-rotation (AUDIOÆ DVD Æ VCR Æ TV Æ CBL).Once you have found a code that turns the device on / off, press [OK] to lock in this code. Thepower / mode buttons will blink 3-times and go out.5. Repeat steps 2 to 4 above for each of the remaining electronic devices you wish to program the remote tooperate.6. Programming Your TV / VCR Combination1. First, turn on your TV / VCR combination device and install a VHS tape.-4-
Synergy.doc2. Next, program your remote to operate the TV functions.Using the Code Entry Programming method described in Section 5, find a TV Setup Code that operates theTV functions (Power, Vol /-, Mute) of your TV / VCR combination.3. Last, program your remote to operate the VCR functions.Using the Code Entry Programming method described in Section 5, enter, lock and test each 3-digit VCRSetup Code for your brand until a code is found that operates the transport functions (Play, Stop, Rew,Pause, Rec) functions of your TV / VCR combination.7. Programming Your TV / DVD or TV / VCR / DVD Combination1. First, turn on your TV / DVD combination device and install a DVD.2. Next, program your remote to operate the TV functions.Using the Code Entry Programming method described in Section 5, find a TV Setup Code that operates theTV functions (Power, Vol S/T, Mute, Ch S/T, 0-9) of your TV / DVD unit.3. Last, program your remote to operate the DVD functions.Using the Code Entry Programming method described in Section 5, enter, lock and test each 3-digit DVDSetup Code for your brand until a code is found that operates the transport functions (PLAY, STOP, REW,FWD, PAUSE, REC) of your TV / DVD unit.Before you can test for the correct DVD setup code, you must first press the [MODE] button, then [DVD]button to put the remote in its DVD mode.4. If you have a TV / VCR / DVD combination unit, you would then program your remote to operate the VCRfunctions.Using the Code Entry Programming method described in Section 5, enter, lock and test each 3-digit VCRSetup Code for your brand until a code is found that operates the VCR transport functions (PLAY, STOP,REW, FWD, PAUSE, REC) of your TV / DVD / VCR unit.Before you can test for the correct VCR setup code, you must first press the [MODE] button, then [VCR]button first to put the remote in its VCR mode.TV Setup l & 8211233-5-
Synergy.docCoronadoCraigCrownCurtis MathesDaewooDaytronDumontElectro altaGoldstar (LG)GrundigHall MarkHitachiInkelJC PenneyJVCKawashoKMCKTVKurazaiLG (Goldstar)LodgenetLogikLuxmanLXIMagnavox (Philips)MajesticMarantzMegatronMemorexMGA / MitsubishiMontgomery 08213213073026068091397213107200162-6-
QuasarRadio SharpSignature hibaTotevisionUniversalVidtechViewsonicWardsWhite 08108048405VCR Setup CodesAdmiralAdventuraAiwaAkaiAudio DynamicsBell & HowellBroksonicCanonCitizenColortymeCraigCurtis 58359247331363112343247344291345346365291-7-
Synergy.docEmersonFisherFunaiGEGo VideoGoldstar (LG)Harman KardonHitachiInstant ReplayJC PenneyJCLJVCKenwoodLG (Goldstar)LloydLogikLXIMagnavox tgomery WardMulti TechNECOrionPanasonicPentaxPhilcoPhilips ature itechVector 4238243331359035331078081-8-
Synergy.docVideo 37085124133087210135DVD Setup CodesApex DigitalB144DenonDVD-VideoECAGEGoldstar (LG)GradienteHarmon KardonHitachiJVCKenwoodKLHLG 3185079436113Audio Setup CodesCompact DiscADCAkaiAiwaCarverCrownDenonFisherGoldstar (LG)Harman KardonJVCKenwoodKrolLG (Goldstar)Magnavox anasonicPhilips (Magnavox)PioneerQuasarRadio 274176 274 289299084 119 296249231 290319266 437084 119 296127433190 266 279289309-9-
4290280289292 293242 311 320208 317Receiver / erFosgate AudionicsGoldstar (LG)Harman KardonHitachiJensenJVCKenwoodLG sonicParasoundPhilips (Magnavox)PioneerQuasarRadio 6440180307180257 305 306241277283 284 285171 304229 321074 438 441137 251 298267268267057 232 287088 239 265442316241254 303083 088 239265Code Number Read-BackTo identify the 3-digit setup codes stored under the Point and Press programming method, follow these steps:To identify the TV setup code 1. Press [TV], then [OK] together until the [TV] button illuminates.2. Press [INFO]. The [TV] button will “blink back” the code numbers, with a 1-second interval between eachdigit of the code.- 10 -
Synergy.docExample: For code “035”, the remote will blink 10 times, then 3 times, then 5 times.To identify the 3-digit VCR code, press [VCR], then [OK] in step 1, then press [INFO].To identify the 3-digit DVD code, press [DVD], then [OK] in step 1, then press [INFO].To identify the 3-digit AUDIO code, press [AUDIO], then [OK] in step 1, then press [INFO].9. ALL SmartKey Once you have programmed the remote to operate your electronic devices, you can press the [ALL] SmartKey toturn your Cable set-top terminal and TV on / off with one button press. You can also program the [ALL] button toturn on / off additional electronic devices and / or tune your TV to its correct output channel.Programming the [ALL] SmartKey 1. Press [ALL], then [MENU] together until the [CBL] button illuminates.2. Enter one of the following options on the keypad of the remote:[0] - Turns on / off CBL TV (default setting)[1] - Turns on / off CBL TV and tunes TV to output Channel 3.[2] - Turns on / off CBL TV and tunes TV to output Channel 2.[3] - Turns on / off CBL TV and tunes TV to output Channel 4.[10] - Turns on / off CBL TV VCR DVD[4] - Turns on / off CBL TV VCR DVD and tunes TV to output Channel 3.[5] - Turns on / off CBL TV VCR DVD and tunes TV to output Channel 2.[6] - Turns on / off CBL TV VCR DVD and tunes TV to output Channel 4.[11] - Turns on / off CBL TV VCR DVD AUDIO[7] - Turns on / off CBL TV VCR DVD AUDIO and tunes TV to output Channel 3.[8] - Turns on / off CBL TV VCR DVD AUDIO and tunes TV to output Channel 2.[9] - Turns on / off CBL TV VCR DVD AUDIO and tunes TV to output Channel 4.[12] - Turns on / off CBL TV AUDIO[13] - Turns on / off CBL TV AUDIO and tunes TV to output Channel 3[14] - Turns on / off CBL TV AUDIO and tunes TV to output Channel 2[15] - Turns on / off CBL TV AUDIO and tunes TV to output Channel 43. As soon as you select an option, the [CBL] button will blink 3-times and go out.Using the [ALL] SmartKey When pressing the [ALL] SmartKey , be sure to keep the remote control aimed at your electronic devices untilyour electronic devices turn on or / off.Whenever the [ALL] SmartKey is pressed, the mode of the remote control will automatically switch back toCable.10.Volume ControlWhen you first program your remote, volume / mute are controlled through your TV (except AUDIO which defaultsto the AUDIO device). The volume control options in each mode of the remote are:CBLTVVCRDVDTV (default), Cable or Audio.TV (default), Cable or Audio.TV (default), Cable or Audio.TV (default), Cable or Audio.- 11 -
Synergy.docAUDIOAUDIO device (default), Cable or TV.To control volume / mute through your Cable set-top terminal in the remote’s Cable mode 1. Press [CBL], then [OK] together until the [CBL] button illuminates.2. Press [VOL ], then [CBL] for Cable volume. The [CBL] button will blink 3-times and go out.To return volume control to your TV, repeat step 1, then press [VOL ], then [TV] in step 2.11. Channel Memory Button - [M1]Your remote has 1 Channel Memory Button ([M1] - See Section 15) which can store up to 5 cable channels. Thisbutton may come pre-set / labeled to channels selected by your cable operator. If this button has not been pre-setby your cable operator, it can be programmed as follows:Programming Channel Memory ButtonTo program the [M1] button to cable channels 1, 12, 123, 1234, 17, follow these steps:1. Press [M1], then [CBL] together until the [CBL] button illuminates.2. Enter each channel as follows (ex. assumes 4-digit channel format):a.b.c.d.e.f.g.h.i.Enter 1st channel # - 0001.Press [CH ] to advance to next channel # setting.Enter 2nd channel # - 0012.Press [CH ] to advance to next channel # setting.Enter 3rd channel # - 0123.Press [CH ] to advance to next channel # setting.Enter 4th channel # - 1234.Press [CH ] to advance to next channel # setting.Enter 5th channel # - 0017.3. Press [M1] to store the above channels. The [CBL] button will blink 3-times and go out. To store fewerthan 5 channels, you can press the [M1] button any time after entering a complete channel number.Using Channel Memory ButtonUsing the above programmed channels as an example 1.2.3.4.5.6.Press [M1] – Cable set-top terminal tunes to channel 0001.Press [M1] again – Cable set-top terminal tunes to channel 0012.Press [M1] again – Cable set-top terminal tunes to channel 0123.Press [M1] again – Cable set-top terminal tunes to channel 1234.Press [M1] again – Cable set-top terminal tunes to channel 0017.Press [M1] again – Cable set-top terminal tunes to channel 1 .repeat.Whenever the Channel Memory button is pressed, the function of the transport buttons will automatically switchback to Cable.When pressing the Channel Memory Button, be sure to keep the remote control aimed at your Cable set-topterminal to ensure the full channel numbers are received in their entirety.If you are using your Synergy V remote to operate a Cable set-top terminal other than the Motorola 62xx seriesDVR model, you may only have to enter channels in a 3-digit format (ex. 012).12. InputThis button changes the input source of your electronic devices. In the remote's Cable mode, this operates a Cable- 12 -
Synergy.docfunction. In the remote's TV mode, this button changes the Input Source (Input 1, Input 2.) on your TV. In theremote's VCR mode, this button changes the TV / VCR Input on your VCR.You can program this button so that in the remote's Cable mode, [INPUT] will operate the Input functionon your TV or VCR, eliminating the need to change modes on the remote.To program [INPUT] to operate your TV Input function in the remotes cable mode.1. Press [INPUT], then [OK] together until the [CBL] button illuminates.2. Press [TV]. The [CBL] button will blink 3-times and go out.Note: You can also press [VCR] in step 2 above to operate the TV / VCR function on your VCR. Or press [CBL] toreturn to the normal CBL Video Source function.13. ResetTo reset your remote control to its factory default settings 1. Press [CBL], then [OK] together until the [CBL] button illuminates.2. Press [MENU], then [MENU] again. The [CBL] button will blink 3 times and go out.Reset returns the ALL SmartKey , Volume / Mute, Mode Lock features to their factory default settings.14.Additional Programming Information, Troubleshooting, TermsAdditional Programming Information1. The power / mode buttons will illuminate in slow-rotation (i.e. CBL Æ TV Æ VCR Æ DVD Æ AUDIO Æ CBL )while the remote is in a programming mode. In the absence of a keypress entry, the power / mode buttons willstop illuminating after 45 seconds and the remote will exit the programming mode.2. When programming the remote control using the [CH ] or [CH -] buttons (Power function) in the Point andPress Programming method, you may find a code that turns a device off but not back on. If this happens a. The correct code has not been found as you may have a code that operates some but not all of thefunctions of your device. Continue pressing [CH ] until your device turn on.ORb. You may have gone past the correct matching code. Try pressing [CH -] one press at a time until youfind a code that turns your device back on.3. When using the Point and Press Programming method, you can also program your remote using buttons otherthan the [CH ] or [CH -] as described in Section 5 as follows:a. [VOL ] – to “go forward” through the codes using the “VOL ” function on your devices.b. [VOL -] – to “go back” through the codes using the “VOL -“ function on your devices.Note: When you find the correct code, the volume of the device being programmed will increase ordecrease.c. [S] - to “go forward” through the codes using the “CH ” function on your devices.d. [T] - to “go back” through the codes using the “CH –“ function on your devices.Note: When you find the correct code, the channel of the device being programmed will increase ordecrease.e. [XX] - to “go forward” through the codes using the “Fast Forward” function on your devices.f. [WW] - to “go back” through the codes using the “Rewind” function on your devices.- 13 -
Synergy.docNote: When you find the correct code, the fast-forward or rewind function of the device being programmedwill be performed. To simplify programming using these buttons, insert a VHS tape or DVD in the devicebeing programmed.You can also program your remote using the other available functions as follows:a. Press [OK], then [MUTE] together until the power / mode buttons illuminate in slow-rotation (i.e. CBLÆ TV Æ VCR Æ DVD Æ AUDIO Æ CBL ).b. In this order, carefully press [0], [0], [0], [CH ] and [VOL ]. The power / mode buttons illuminate in slowrotation (i.e. CBL Æ TV Æ VCR Æ DVD Æ AUDIO Æ CBL ).c. You can now program your remote using the [CH ], [CH -], [VOL ], [VOL -], [ ], [T], [FFWD], [REW],[PLAY], [STOP], [REC], [PAUSE], [LAST], [FAV], [0] - [9] buttons. When you find the correct code, thefunction associated with the selected button will be performed.4. Your remote is equipped with a Point and Press Programming label on the back of its case. This will helpyou quickly program the remote without using codes.Troubleshooting / Tips1. If the same button is pressed and held for 45-seconds, your remote control will turn itself off automatically.This extends the battery life should the remote become lodged under or between heavy objects, for examplesofa cushions.2. If you have a TV that’s operated by remote control, it is recommended that you plug it directly into a walloutlet instead of the cable set-top terminal.3. If you have any questions concerning the brand, model or operation of your cable set-top terminal, contactyour cable operator.Frequently Used TermsAUDIO Devices - Audio receivers, amplifiers, CD players that you can program your remote to operate.DVR - Digital Video Recorder.Default Setting – How your remote is set when you receive it from your cable operator.Electronic Components / Devices - The various electronics device the remote is designed. These include cableset-top terminals, TVs, VCRs, DVDs, audio-video receivers, amplifiers and CD players.Fast-Rotation - The power / mode buttons will illuminate in a fast sequence (i.e. CBL Æ TV Æ VCR Æ DVD ÆAUDIO Æ CBL ) repeated every 1/3 second. Fast-rotation occurs when the remote is receiving keypresses toprogram it to your electronic devices.Mode - The device the remote is set to operate (ex. Cable, TV, VCR, DVD, Audio)PIP – Picture-in-picture functionality through your Cable set-top terminal.Program (Setup) – The process of teaching your remote control to operate your electronic devices.Slow-Rotation - The power / mode buttons illuminate in a slow sequence (i.e. CBL Æ TV Æ VCR Æ DVD Æ AUDIOÆ CBL ) repeated every 1 second. Slow-rotation illumination occurs when the remote is in the programmingmode, waiting for the next entry on the keypad of the remote.TV Output Channel - The channel your TV needs to be set on for proper Cable reception (most often TV channel 3,but may be TV channel 2 or 4). If you have any questions concerning your TV output channel, contact your cableoperator. Or, with your cable set-top terminal turned on, try setting your TV to channel 2, 3 or 4 to obtain a clearpicture.- 14 -
Synergy.docTransport Functions - These are the [STOP], [PLAY], [FWD], [REW], [PAUSE] and [REC] buttons. In the remotecontrol's Cable mode, these buttons operate your Cable set-top features. In the remote control's VIDEO mode,these operate your VCR or DVD functions.VIDEO Devices - VCR or DVD players.Device Setup CodesIf you find that the setup codes listed above do not operate your devices, it is possible your remote wasmanufactured before the revision date printed on this Instruction Manual. If this occurs, contact your cable operatorand request a newer version of your remote control. 2004, Contec CorporationRev. 09/04Point and Press , Memory Guard , SmartKey and Synergy are registered trademarks of Contec CorporationExplorer is a registered trademark of Scientific-Atlanta, Inc.Voyager is a registered trademark of Pioneer New Media Technologies, Inc.U.S. Patent 6,507,306- 15 -
Synergy.doc15. Using Your Synergy V - Universal / DVR Remote ControlImportant: The following diagram shows how to use the buttons on your remote control to operate the DVR andPIP functions of the Motorola DCT 62xx series DVR set-top terminal. To access these functions, set the remotecontrol to its Cable mode by pressing the [MODE] button, followed by the [CBL] button.CBL & TV on / off(programmable)Illuminate / select electronic devicebeing operated. Press Mode, then CBL - for Cable modeTV - for TV modeVCR - for VCR modeDVD - for DVD modeAUDIO - for Audio modeIndividual device on / off powerAccess on-screen displayfor cable deviceDisplay channel / programinformationAccess cable guideMoves through on-screen display orcable guide menu (S,T,X,W)Move / through on-screendisplays, cable guideAccess on-screen display for cabledeviceSelects highlighted on-screenor cable guide choiceFunctions set by cable operator(A, B, C)Exit any on-screen displayDayW / X in cable guideRecall pre-selected favoritechannelsDisplay Help screen on cable deviceReturn to last selected channelReplay previous few seconds ofprogram (DVR set-top terminalsonly)Display live TV programming(DVR set-top terminals only)Fast-forward DVR, VCR, DVDListing of recorded programs (DVRset-top terminals only)Play DVR, VCR, DVDRewind DVR, VCR, DVDRecord DVR, VCRStop DVR, VCR, DVDPause DVR, VCR, DVDChange viewing aspect of cabledeviceDigital MusicMove PIP screenPIP on / offPIP channel /-Swap PIP & and main screenSelects video sourceM1Access Pay-Per-Viewprogramming where availableChannel memory button (may belabeled or pre-set by cable operator)Access Video-On-Demandprogramming where available- 16 -
Synergy.doc - 2 - 1. Introduction Your Synergy V Universal / DVR remote control is simple to program, easy to use, and can operate up to five (5) electronic devices, which include: CABLE Cable set-top terminals TV Televisions VCR VCR DVD DVD AUDIO Audio receivers, amplifiers, CD players Before you can use your remote control, it must be programmed (set-up) to operate the above devices.
Malvasia di Casorzo d’Asti/Malvasia di Casorzo/Casorzo DOC Malvasia di Castelnuovo Don Bosco DOC Monferrato DOC Nebbiolo d’Alba DOC Piemonte DOC Pinerolese DOC Rubino di Cantavenna DOC Sizzano DOC Strevi DOC Valli Ossolane DOC Valsusa DOC Verduno Pelaverga/Verduno DOC Your first stop for information about Italian wine
This User Manual is a guide for use during the installation, normal operation and maintenance of a Synergy System or Synergy UV Water Purification System. 'Synergy' is used in this manual to refer to either the Synergy or the Synergy UV System unless otherwise noted. It is highly recommended to completely read this manual and to
Grey 7005 51 Charcoal 7016 9 For full details on Doc M refer to the Armitage Shanks Doc M Solutions brochure. 1 : 11 : 1 : 1. Doc M 1 : 11 : 2 : 1 Doc M 1 : 11 : 1 : 2 Doc M. Doc M Doc M 1 : 11 : 2 : 2 1 : 11 : 2 : 3 Close Coupled Left Or Right Hand Packs Doc M pack, specifically designed to latest recommendations which
three new synergy measures: the expected total cost synergy, the relative risk reduction synergy, and the absolute risk reduction synergy for the assessment of the potential strategic advantages. We illustrate the analytical framework with two sets of numerical examples
synergy and evolution. Our synergy and evolution elevators combine state-of-the-art technology with flexible design. Immerse yourself in the design world of these two elevator families and choose the design that suits your taste and requirements. 4 synergy and evolution. With its compact dimensions, the synergy series is perfect for
ICAO Doc 9184, Airport Planning Manual, Parts 1 to 3; ICAO Doc 9261, Heliport Manual; ICAO Doc 9332, Manual on the ICAO Bird Strike Information System (IBIS); ICAO Doc 9365, Manual of All-Weather Operations; ICAO Doc 9426, Air Traffic Services Planning Manual; ICAO Doc 9476, Manual of Surface Movement Guidance and Control Systems (SMGCS); ICAO .
AC31 Doc. 14.1/PC25 Doc. 17 – p. 1 Original language: English AC31 Doc. 14.1/PC25 Doc. 17 CONVENTION ON INTERNATIONAL TRADE IN ENDANGERED SPECIES OF WILD FAUNA AND FLORA _ Joint sessions of the 31st meeting of the Animals Committee and the 25th meeting o
CIE IGCSE Business Studies Paper 1 Summer & Winter 2012 to 2015 . UNIVERSITY OF CAMBRIDGE INTERNATIONAL EXAMINATIONS International General Certificate of Secondary Education MARK SCHEME for the May/June 2012 question paper for the guidance of teachers 0450 BUSINESS STUDIES 0450/11 Paper 1 (Short Answer/Structured Response), maximum raw mark 100 This mark scheme is published as an aid to .
