TIPPING SOLUTIONS - Hyva
TIPPING SOLUTIONSCOMPONENT CATALOGVALVEShyva.comhyva.comSubject to change without notice1PG-E PDCL-0005 / 01-06-2020 / RV AA
hyva.comSubject to change without notice2PG-E PDCL-0005 / 01-06-2020 / RV AA
TABLE OF CONTENTHT-VALVESHT-VALVES INTRODUCTION .6HT-1150 VALVES INTRODUCTION .6Ÿ HT-1150 VALVES.7ŸSPARE PARTS FOR HT-1150 VALVES.8Ÿ HT-1220 VALVES INTRODUCTION .9Ÿ HT-1220 VALVES .10ŸŸ SPARE PARTS FOR HT-1220 VALVES.12HT-2220 VALVES INTRODUCTION .14Ÿ HT-2220 VALVES .15ŸSPARE PARTS FOR HT-2220 VALVES.17Ÿ PRESSURE CARTRIDGE FOR HT VALVE & PRESSURE TEST EQUIPMENT.19ŸTIPPING VALVESTIPPING VALVES INTRODUCTION .20ŸŸMECHANICAL VALVES .21PNEUMATIC VALVES .23ELECTRICAL VALVES.25Ÿ MOUNTING ACCESSORIES FOR 40-80-150L TIPPING VALVES.27Ÿ ELECTRICAL ACCESSORIES FOR TIPPING VALVES .28Ÿ CABLE CONTROLS FOR VALVES .29ŸKNOCK-OFF VALVESKNOCK-OFF VALVES INTRODUCTION.31KNOCK-OFF VALVES.32ŸOTHER VALVES .36OTHER VALVES INTRODUCTION .36PRESSURE RELIEF VALVES .37ŸSPARE PARTS PRESSURE RELIEF VALVES.39DIVERTER VALVES .40Ÿ SPARE PARTS DIVERTER VALVES .41HOSE BURST VALVES.42NON RETURN VALVES.43FLOW RESTRICTOR VALVES.43MULTI-SECTION VALVES.44ŸŸŸŸŸŸhyva.comSubject to change without notice3PG-E PDCL-0005 / 01-06-2020 / RV AA
hyva.comSubject to change without notice4PG-E PDCL-0005 / 01-06-2020 / RV AA
HT-VALVES INTRODUCTIONHyva tipping valvesThe tipping valve is the most critical component of the hydraulic tipping system as it directly influencesthe safety, performance and efficiency of the tipper. With this in mind, Hyva has always paid a lot ofattention to these components to deliver to the market the safest and the most efficient solution –currently represented by the HT range of tipping valves.The Hyva HT valve series is a complete range of tipping valves to be used for different cylinder types andother applications driven by hydraulic systems. The HT 1220 is a single pressure series and the HT 2220 is adouble pressure type. Both types can be used for oil flow up to 220 litres per minute and the pressuresettings are from 110 to 350 bar.Dual pressure valves (HT 2220) are used for applications where two working pressures are required, thepressure selection can be manual or pneumatic in the AS version.For smaller flows, Hyva offers the HT 1150 valve series. This valve is suitable for oil flow of 150 litres perminute and the working pressure settings available are from 135 to 250bar.The complete range of Hyva HT tipping valves is based on the pilot operated pressure relief valve designwith fixed pressure setting (by means of fixed value cartridges), which protects both the cylinder and thepump from overpressure. These pressure cartridges are fully interchangeable, so the pressure can beadjusted by its replacement in an easy and safe manner. The HT series is also designed to allowproportional lowering which is of great importance when lowering (half) loaded tipper bodies.Hyva HT tipping valves (TNK version) can be mounted on the oil tank which reduces the numberof hoses and fittings and consequently the possibility of leakages. The other version (SAE version) can bemounted directly on the cylinder inlet port, in which case the valve also acts as a safety device in the eventof a pressure feeding hose burst. The hose burst valve prevents the tipper body from falling in anuncontrolled way. Hyva HT valves are pneumatically operated with air controls optimised to ensure safeand precise operation of the system during its overall long lifetime.Code system for HT valvesTipping valveHTSAE1 220190P1”HTValve typeSAE1190P1”Subject to change without noticeSAE Cylinder mountedTNK Tank mountedPressure relief cartridge220hyva.comHT Air controlled tipping valveMounting type1 1 cartridgeMax. flow in valve150 150 l/min.Max. pressure (bar)220 220 l/min.2 2 cartridgesPump connection5PG-E PDCL-0005 / 01-06-2020 / RV AA
HT-1150 VALVES INTRODUCTIONHyva HT-1150 tipping valvesThis series of valves is designed to be used with oil flows up to 150 litres per minute. The valves are theoptimal choice for systems working with smaller tipping cylinders or with applications where highflow/speed is not the key requirement. The unique design of the housing means that the valve can bemounted either on the tank or directly on the cylinder. The mounting kits for both mounting options areincluded and delivered with the valve.The working pressure range is from 135 to 250 bar and the maximum working pressure is set by Hyva'swell-known concept of the 'fixed value cartridge'. The pressure cartridges used in these valves are fullyinterchangeable with other HT series valves.The hydraulic connections are standard G ¾“, but for heavier working conditions the G 1” connection forthe pump port is available. The valve is also equipped with a G ¼” connection port for a pressure sensorand the pneumatic control port is suitable to connect with 6mm pneumatic hoses.The valve spool design ensures precise operation - the lowering operation is proportional and the loweringspeed can be adjusted.hyva.comSubject to change without notice6PG-E PDCL-0005 / 01-06-2020 / RV AA
HT-1150 VALVESHT-1150-TNK / SAEPart no.DescriptionFlow(L/min.)Weight(kg)Hydraulic connectionsPTCMPCMax. Pressure(bar)14767213TIP VALVE -SAEG¼”13514767215TIP VALVE -SAEG¼”15014767217TIP VALVE -SAEG¼”17014767219TIP VALVE -SAEG¼”19014767222TIP VALVE -SAEG¼”22014767225TIP VALVE -SAEG¼”25014767263TIP VALVE AEG¼”13514767265TIP VALVE AEG¼”15014767267TIP VALVE AEG¼”17014767269TIP VALVE AEG¼”19014767272TIP VALVE AEG¼”22014767275TIP VALVE AEG¼”250For direct mounting on1234567Pump connectionTank connectionCylinder connection SAEPneumatic connection (Tip) 6 mmPneumatic connection (Lower) 6 mmPressure relief cartridgeMPC Measure Pressure Cylinder(Pressure gauge point)8Adjustment screw (int.hex. 5)(To adjust the lowering speed)Ÿ TNK: Hyva tank mounting plateŸ SAE: SAE inlet of Hyva cylinder6327PTCHYDRAULIC SYMBOL1548SAFETY:HT valve fitted on cylinder (SAE) portprovides hose burst safety functionHT1150-P ” - TNK/SAEhyva.comSubject to change without noticeHT1150-P1” - TNK/SAE7PG-E PDCL-0005 / 01-06-2020 / RV AA
SPARE PARTS FOR HT-1150 VALVESMOUNTING KITSMounting kitsKit numberCylinder (SAE)*14735162Tank (TNK)*1473516814735162** included with valve14735168SEAL KITS AND AIR ASSEMBLY PARTS14844010Part no.Description14844010SEAL KIT PT/JT/HT VALVEQty.114810517AIR COUPLING ” - 6MM - 00214810517hyva.comSubject to change without notice8PG-E PDCL-0005 / 01-06-2020 / RV AA
HT-1220 TIPPING VALVES INTRODUCTIONHyva HT-1220-SAE tipping valves.This series of valves, which is designed to be used with oil flows up to 220 litres per minute, is the optimalchoice for systems working with bigger tipping cylinders or with heavy duty applications where highflow/speed is one of the key requirements. The SAE version is designed to be mounted on the Hyvacylinder directly, using the mounting kit supplied with the valve. This solution provides easy mounting,precise operation of the tipping cylinder and, as an additional safety feature, the HT 1220 SAE acts also as ahose burst valve in the event of failure of the pressure feeding hose. Hyva ALPHA cylinders are compatiblewith this SAE type connection.The working pressure range is from 135 to 250 bar, with the maximum working pressure set by Hyva's fixedvalue cartridge. The pressure cartridges used in this valve are fully interchangeable with other HT seriesvalves. The hydraulic connections are G 1” to enhance high oil flow capability. The valve is also equippedwith a G ¼” connection port for a pressure sensor and the pneumatic control port will connect with 6mmpneumatic hoses.The valve spool design ensures precise operation – the lowering operation is proportional and the loweringspeed can be adjusted.Hyva HT-1220-TNK tipping valves.This series of valves, which is designed to be used with oil flows up to 220 litres per minute, is the optimalchoice for systems working with bigger tipping cylinders or with heavy duty applications where highflow/speed is one of the key requirements. The TNK version can be mounted on the oil tank, using themounting kit supplied with the valve, and is most popular for semitrailer-tractor tippers, but also in manyother applications where the valve is not mounted on the cylinder. Hyva oil tanks are compatible with thistype of connection.The working pressure range is from 110 to 350 bar, with the maximum working pressure set by Hyva's fixedvalue cartridge. The pressure cartridges used in this valve are fully interchangeable with other HT seriesvalves. The hydraulic connections are G 1” to enhance high oil flow capability. The valve is also equippedwith a G ¼” connection port for a pressure sensor and the pneumatic control port will connect with 6mmpneumatic hoses.The valve spool design ensures precise operation – the lowering operation is proportional and the loweringspeed can be adjusted.hyva.comSubject to change without notice9PG-E PDCL-0005 / 01-06-2020 / RV AA
HT-1220 VALVESHT-1220-SAEPart no.DescriptionFlow(L/min.)Weight(kg)Hydraulic connectionsPTCMPCMax. Pressure(bar)14767453TIP VALVE 4767455TIP VALVE 4767457TIP VALVE 4767459TIP VALVE 4767461TIP VALVE 4767463TIP VALVE or direct mounting onŸ SAE: SAE inlet of Hyva cylinder1234567Pump connectionTank connectionCylinder connection SAEPneumatic connection (Tip) 6 mmPneumatic connection (Lower) 6 mmPressure relief cartridgeMPC Measure Pressure Cylinder(Pressure gauge point)8Adjustment screw (int.hex. 5)(To adjust the lowering speed)63721PTCHYDRAULIC SYMBOL548SAFETY:HT valve fitted on cylinder (SAE) portprovides hose burst safety functionhyva.comSubject to change without notice10PG-E PDCL-0005 / 01-06-2020 / RV AA
HT-1220 VALVESHT-1220-TNKPart no.DescriptionFlow(L/min.)Weight(kg)Hydraulic connectionsPT1T2CMPCMax. Pressure(bar)14767111TIP VALVE �”11014767113TIP VALVE �”13514767115TIP VALVE �”15014767117TIP VALVE �”17014767119TIP VALVE �”19014767122TIP VALVE �”22014767125TIP VALVE �”25014767128TIP VALVE �”28014767135TIP VALVE �”350For direct mounting onŸ TNK: Hyva tank mounting plate12A2B34567163782APT1T2CPump connectionTank connectionAlternative tank connectionCylinder connectionPneumatic connection (Tip) 6 mmPneumatic connection (Lower) 6 mmMPC Measure Pressure Cylinder(Pressure gauge point)Pressure relief cartridgeAdjustment screw (int.hex. 5)(To adjust the lowering speed)HYDRAULIC SYMBOL2A548T1T2SAFETY:HT valve fitted on cylinder (SAE) portprovides hose burst safety functionhyva.comSubject to change without notice11PG-E PDCL-0005 / 01-06-2020 / RV AA
SPARE PARTS FOR HT-1220 VALVESMOUNTING KITSKit numberMounting kitsCylinder (SAE)*14735175Tank (TNK)*14735168Chassis**14735208* included with valve** not included with valve147351751473516830 Nmdelivered with valve14735208delivered with valve123SEAL KITS AND AIR ASSEMBLY PARTS14844010Part no.DescriptionQty.14844010SEAL KIT PT/JT/HT VALVE114810517AIR COUPLING ” - 6MM - 00214810517hyva.comSubject to change without notice12PG-E PDCL-0005 / 01-06-2020 / RV AA
SPARE PARTS FOR HT-1220 VALVESCHASSIS MOUNTING BRACKET FOR HT-1220 VALVESPart no.Description09238050**MOUNTING BRACKET HT/RELIEF/DIVERTER IN CHASSIS** not included with valve, to be ordered separately09238050hyva.comSubject to change without notice13PG-E PDCL-0005 / 01-06-2020 / RV AA
HT-2220 TIPPING VALVES INTRODUCTIONThis series of valves is designed to be used with oil flows up to 220 litres per minute with dual maximumworking pressure setting. This valve is the optimal choice for multi-functional systems – working, forexample, with tipping cylinders and other applications such as walking floor systems or applications wherethe tipping cylinders on the truck and trailer operate with different working pressures. This is also a verygood solution for customers who use two types of cylinders with higher and lower maximum workingpressures.This valve is available in TNK version to be mounted on the oil tank, using the mounting kit supplied withthe valve. This way of mounting is the most popular for the semitrailer-tractor where the dual pressurefeature is mostly required, but can also be applied to tipper trucks working with tipping trailers. Hyva oiltanks are compatible with this type of connection. The hydraulic connections are G 1” to enhance high oilflow capability. The valve is also equipped with a G ¼” connection port for a pressure sensor and thepneumatic control port will connect with 6mm pneumatic hoses.The valve spool design ensures precise operation – the lowering operation is proportional and the loweringspeed can be adjusted.Hyva-HT-2220-TNK-MS (Mechanical Switch) tipping valvesThe switch between the working pressures (Low Pressure to High Pressure) is executed manually by aswitch on the valve. The working pressure range for the Lower Pressure range is from 110 to 190 bar and forthe Higher Pressure from 220 to 350 bar. The maximum working pressures are set by Hyva's fixed valuecartridge. The pressure cartridges used in this valve are fully interchangeable with other HT series valves.Hyva HT-2220-TNK-AS (Air Switch) tipping valvesThe switch between the working pressures (Low Pressure to High Pressure) is executed pneumatically byan air switch. This switch can be controlled remotely from the air control in the truck cabin with no needfor the operator to step out. The working pressure range for the Lower Pressure range is from 150 to 190bar and for the Higher Pressure from 220 to 350 bar. The maximum working pressures are set by Hyva'sfixed value cartridges. The pressure cartridges used in this valve are fully interchangeable with other HTseries valves.hyva.comSubject to change without notice14PG-E PDCL-0005 / 01-06-2020 / RV AA
HT-2220 VALVESHT-2220-TNK (MECHANICAL SWITCH)Part no.DescriptionFlow(L/min.)Weight(kg)Hydraulic connectionsPT1T2Max. Pressure (bar)***CMPCLPHP22014767150TIP VALVE ��G¼”11014767152TIP VALVE ��G¼”15022014767155TIP VALVE ��G¼”15025014767158TIP VALVE TIP VALVE HT-TNK-2220-150-350-P1”2206.2G1”14767172TIP VALVE ��G¼”17022014767175TIP VALVE ��G¼”17025014767178TIP VALVE ��G¼”17028014767185TIP VALVE ��G¼”17035014767172TIP VALVE ��G¼”19022014767175TIP VALVE ��G¼”19025014767178TIP VALVE ��G¼”19028014767185TIP VALVE ��G¼”190350*** The user can select the maximum pressure setting by lifting and turning the selector towards HP or LPFor direct mounting onŸ TNK: Hyva tank mounting plate12A2B3456Pump connectionTank connectionAlternative tank connectionCylinder connectionPneumatic connection (Tip) 6 mmPneumatic connection (Lower) 6 mmMPC Measure Pressure Cylinder(Pressure gauge point)7APressure relief cartridge (HP)7BPressure relief cartridge (LP)8Manual pressure selector9Adjustment screw (int.hex. 5)(To adjust the lowering speed)7B7A18632A2BPT1T2CHYDRAULIC SYMBOL549LOWHIGHT1hyva.comSubject to change without notice15T2PG-E PDCL-0005 / 01-06-2020 / RV AA
HT-2220 VALVESHT-2220-TNK (AIR SWITCH)Part no.DescriptionFlow(L/min.)Weight(kg)Hydraulic connectionsMax. Pressure (bar)***PT1T2CMPCLPHP14767700TIP VALVE G1”G¼”15022014767702TIP VALVE G1”G¼”15025014767704TIP VALVE G1”G¼”15028014767706TIP VALVE G1”G¼”15035022014767708TIP VALVE G1”G¼”17014767710TIP VALVE G1”G¼”17025014767712TIP VALVE G1”G¼”17028014767714TIP VALVE G1”G¼”17035014767716TIP VALVE G1”G¼”19022014767718TIP VALVE �G1”G1”G¼”19035014767720TIP VALVE HT-TNK-2220-190-280-AS-P1”2206.3G1”14767722TIP VALVE HT-TNK-2220-190-350-AS-P1”2206.3G1”*** The user can select the maximum pressure setting by lifting and turning the selector towards HP or LPFor direct mounting on12A2B3456Pump connectionTank connectionAlternative tank connectionCylinder connectionPneumatic connection (Tip) 6 mmPneumatic connection (Lower) 6 mmMPC Measure Pressure Cylinder(Pressure gauge point)7APressure relief cartridge (HP)7BPressure relief cartridge (LP)8Air switch (AS) 6 mm(Pneumatic pressure selector)9Adjustment screw (int.hex. 5)(To adjust the lowering speed)Ÿ TNK: Hyva tank mounting plate7B7A81632A2B54PT1T2CHYDRAULIC SYMBOL9LOWASHIGHT1hyva.comSubject to change without notice16T2PG-E PDCL-0005 / 01-06-2020 / RV AA
SPARE PARTS FOR HT-2220 VALVESMOUNTING KITS147 35 168Kit numberMounting kitsTank (TNK)*14735168Chassis**14735208* included with valve** not included with valve30 Nmdelivered with valve14735208delivered with valve123SEAL KITS AND AIR ASSEMBLY PARTS14844010Part no.DescriptionQty.14844010SEAL KIT PT/JT/HT VALVE114810517AIR COUPLING ” - 6MM - 00214810517hyva.comSubject to change without notice17PG-E PDCL-0005 / 01-06-2020 / RV AA
SPARE PARTS FOR HT-2220 VALVESCHASSIS MOUNTING BRACKET FOR HT-2220 VALVESPart no.Description09238050**MOUNTING BRACKET HT/RELIEF/DIVERTER IN CHASSIS** not included with valve, to be ordered separately09238050hyva.comSubject to change without notice18PG-E PDCL-0005 / 01-06-2020 / RV AA
PRESSURE CARTRIDGE FOR HT-VALVE &PRESSURE TEST EQUIPMENTCARTRIDGE PRESSURE RELIEF HT (FOR ALL HT-VALVES)Part no.Description14772110CARTRIDGE PRESSURE RELIEF HT 110 BAR14772135CARTRIDGE PRESSURE RELIEF HT 135 BAR14772150CARTRIDGE PRESSURE RELIEF HT 150 BAR14772170CARTRIDGE PRESSURE RELIEF HT 170 BAR14772190CARTRIDGE PRESSURE RELIEF HT 190 BAR14772220CARTRIDGE PRESSURE RELIEF HT 220 BAR14772250CARTRIDGE PRESSURE RELIEF HT 250 BAR14772280CARTRIDGE PRESSURE RELIEF HT 280 BAR14772350CARTRIDGE PRESSURE RELIEF HT 350 BARPart TQty.PRESSURE GAUGE COMPLETE CONSISTING OF:PRESSURE GAUGE 400 BAR1ADAPTER M16 - ”BSPOT1ADAPTER M16 - ¼”BSPOT1Subject to change without notice19PG-E PDCL-0005 / 01-06-2020 / RV AA
TIPPING VALVES INTRODUCTIONThese valves are controlled mechanically by a cable system, and the knock-off function can also beactivated mechanically. With these features, this valve is a very good choice for smaller trucks without apneumatic supply system and underbody cylinders. The hydraulic connections are G ½ “. A pressuresensor can be also connected.Mechanical 40 and 80 Ltr. tipping valvesThese smaller valves are designed for applications with small and medium size cylinders. Valves with oilflow of 40 litres per minute are a very good solution for small underbody cylinders, and valves with oil flowof 80 litres per minute are ideal for applications with medium size underbody tippers.These valves are controlled pneumatically, and the knock-off function can be activated mechanically. Withthese features, this valve is a very good choice for smaller trucks with a pneumatic supply system andunderbody cylinders. The hydraulic connections are G ¾ “. A pressure sensor can be also connected.Pneumatic 80 & 150 Ltr. tipping valvesValves with oil flow of 80 litres per minute are designed for applications with small and medium sizecylinders. Valves with oil flow of 150 litres per minute are designed for applications with medium and largesize cylinder. Both types are ideal for applications with medium size underbody tippers.These valves are controlled electrically. This solution is very good choice for smaller trucks without apneumatic supply system and underbody cylinders. The hydraulic connections are G ½ “. A pressuresensor can be also connected.Electric tipping valvesThese valves are designed for applications with small size cylinders. Valves with oil flow of 40 litres perminute are ideal for applications with small size underbody tippers.hyva.comSubject to change without notice20PG-E PDCL-0005 / 01-06-2020 / RV AA
TIPPING VALVES MECHANICALTIPPING VALVE MECHANICAL 40LTR - CABLE KNOCK-OFFPart no.DescriptionFlow(L/min.)Weight(kg)Ports hydraulicRelief valve setting(bar)*Connectionof cable**021418150021418151TIP VALVE FM-40-140BAR MECHANICAL402.5G½”140BAYONETTIP VALVE FM-40-180BAR MECHANICAL402.5G½”180BAYONET* These valves are standard set on 140-180 bar. The maximum setting is 220 bar and can be adjusted by the customer** You can find suitable cable controls with bayonet end on page 28 & 2917657FIXING DIMENSIONS½” GAS30OPTIONAL2666OPTIONAL4XØ8.5½” GASTANK646½” GASLOW6TIPOPTIONAL: PRESSURE SWITCHMOUNTING KITPart no.hyva.com6833.548128.59021418185Subject to change without notice21Part no.Description021416010PRESSURE SWITCH HYD ADJ 350BAR 1/8”BSPOTPG-E PDCL-0005 / 01-06-2020 / RV AA
TIPPING VALVES MECHANICALTIPPING VALVE MECHANICAL 80LTR - CABLE KNOCK-OFFPart no.DescriptionFlow(L/min.)Weight(kg)PortsTANK 1OUTTANK 2INRelief valvesetting (bar)Connectionof cable**021418160TIP VALVE 3/3-80-140-½” CABLE802.5G ”G½”G ”G½”140THREADED021418161TIP VALVE 3/3-80-170-½” CABLE802.5G ”G½”G ”G½”170THREADED021418162TIP VALVE 3/3-80-190-½” CABLE802.5G ”G½”G ”G½”190THREADED** You can find suitable cable controls with threaded end on page 28 & 29144614123A3Rest positionTippingLoweringCable control attachment2IN½”G48125106TANK 2 ”GOPTIONALTANK 1 ”G31OUT ½”G1243.598.5MOUNTING KITPart no.021418186OPTIONAL: PRESSURE SWITCHhyva.comSubject to change without notice22Part no.Description021416010PRESSURE SWITCH HYD ADJ 350BAR 1/8”BSPOTPG-E PDCL-0005 / 01-06-2020 / RV AA
TIPPING VALVES PNEUMATICTIPPING VALVE PNEUMATIC 80LTR - CABLE KNOCK-OFFPart no.DescriptionFlow(L/min.)Weight(kg)PortsTANK 1OUTTANK 2INRelief valve setting(bar)14767620TIP VALVE 080-140-½” TOP PN802.5G ”G½”G ”G½”14014767622TIP VALVE 080-170-½” TOP PN802.5G ”G½”G ”G½”170123AB256Rest positionTippingLoweringProportional loweringTipping3481255014INTANK 2 ”G2½”G9716141ABTANK 1 ”GOUT38½”GMOUNTING KITPart no.021418185OPTIONAL: PRESSURE SWITCHhyva.comSubject to change without notice23Part no.Description021416010PRESSURE SWITCH HYD ADJ 350BAR 1/8”BSPOTPG-E PDCL-0005 / 01-06-2020 / RV AA
TIPPING VALVES PNEUMATICTIPPING VALVE PNEUMATIC 150LTR - CABLE KNOCK-OFFPart TIP VALVE 150-170- ” SIDE PNRelief valve setting(bar)Ports262TANKOUTING ”G ”G ”123AB319IN ”G1702Rest positionTippingLoweringProportional loweringTipping8315.5160184ABTANK ”GOUT ”G60MOUNTING KITPart no.021418186OPTIONAL: PRESSURE SWITCHhyva.comSubject to change without notice24Part no.Description021416010PRESSURE SWITCH HYD ADJ 350BAR 1/8”BSPOTPG-E PDCL-0005 / 01-06-2020 / RV AA
TIPPING VALVES ELECTRICALELECTRICAL TIPPING VALVE*Part sTANKOUTINRelief valve setting(bar)14700094TIPPING VALVE ELECTRICAL 12V-40L-140/190BAR40123.5G ”G ”G ”140 up to 19014700106TIPPING VALVE ELECTRICAL 24V-40L-140/190BAR40243.5G ”G ”G ”140 up to 190* On the electrical tipping valve is no mechanical knock-off possible.TPMMMTPManual (emergency) overide.Push and hold to operate.Test point connection (G ”)MOUNTING KITSPart no.Description021418180FOR MOUNTING ON 3-HOLE (HT) MOUNTING PLATE021418185FOR NATIVE 4-HOLE MOUNTINGOPTIONAL: PRESSURE SWITCHhyva.comSubject to change without notice25Part no.Description021416010PRESSURE SWITCH HYD ADJ 350BAR 1/8”BSPOTPG-E PDCL-0005 / 01-06-2020 / RV AA
TIPPING VALVES ELECTRICALELECTRICAL TIPPING VALVE*Part sTANKOUTINRelief valve setting(bar)021418100TIPPING VALVE ELECTRICAL 12V-40L-140BAR40123.38G ”G ”G ”021418104TIPPING VALVE ELECTRICAL 12V-40L-170BAR40123.38G ”G ”G ”170021418140TIPPING VALVE ELECTRICAL 24V-40L-140BAR40243.38G ”G ”G ”140021418144TIPPING VALVE ELECTRICAL 24V-40L-170BAR40243.38G ”G ”G ”170021418147TIPPING VALVE ELECTRICAL 24V-40L-190BAR40243.38G ”G ”G ”190140* On the electrical tipping valve is no mechanical knock-off possible.264MG½” OUTLOWER128TIP26TPTPManual (emergency) overide.Push and hold to operate.Test point connection (G ”)G½” IN469964824Ø8.5 (4x)MMG ” TPG ” TANKOPTIONAL: PRESSURE SWITCHMOUNTING KITSPart no.DescriptionPart no.Description021418180FOR MOUNTING ON
Ÿ spare parts pressure relief valves . 14767217 tip valve ht-tnk/sae-1150-170-p¾” 150 3.7 g¾” g¾” g¾”-sae g¼” 170 . 14810517 air coupling ” - 6mm - 00 2 seal kits and air
39 Metsästyskiväärit Mauser 9.3x62 SN: 1238xx, aseessa kiikari Nickel 1-4x hakajaloilla, Kunto: hyvä 250 250 40 Metsästyskiväärit Winchester Model 94 .30-30 Win SN: 44568xx, aseessa kiikari Tasco 2-7x32, Kunto: hyvä 200 0 41 Metsästyskiväärit Arisaka 6.5 SN: 2513xx, Arisaka kivääristä tehty metsästysase, Kunto: hyvä 40 0
at this "tipping point" for solar PV. 1. The Tipping Point In his recent best-selling book The Tipping Point, Mal-colm Gladwell scrutinized "that magic moment when an idea, trend, or social behavior crosses a threshold, tips, and spreads like wildfire" [2]. Our PV technology can be char-acterized by such tipping points during its .
the tipping point is determined in part by the strength of white preferences for minority contact, and is higher when whites are more tolerant of minority neighbors. We then set out to test for tipping behavior using decadal changes in neighborhood racial/ethnic composition. A major obstacle is that the location of the tipping point is unknown.
The cause of the tipping can be very different in the two cases, and especially the possibility of predicting a tipping will be different. In the case that the underlying dynamics or the control-parameter are not com-pletely known, there could still be early warning signals in the statistics of the observed fluctuations prior to a tipping point.
HYQUEST SOLUTIONS PTY LTD Tipping Bucket Raingauge TB4 100-01 Issue 9 - 3.13 INSTRUCTION MANUAL TIPPING BUCKET RAINGAUGE MODEL TB4 HYQUEST SOLUTIONS PTY LTD PO BOX 332, LIVERPOOL B.C NSW 1871, AUSTRALIA . V TEST OPERATION C Manually tip the bucket a number of times, ensuring that each tip is being
Chapter 4: Are we facing a 'tipping point'? 26 4.1 Our recycling bins are nearly full 26 4.2 'Empty space' will decrease, but parcels will hit three billion in 10 years 26 4.3 Recycling of packaging is on the decline 27 4.4 A potential 'tipping point' 27 4.5 The importance of separation of materials at our homes 28
Tipping Point facilitated staff reflection on their attitudes and personal beliefs, and built technical knowledge and skills related to the project outcomes. The facilitated dialogues provided an opportunity for staff to weigh their own values, beliefs and opinions about gender, sexuality and power. Phase 1 of the Tipping Point incorporated
BTEC Entry Level (E1, E2, E3) BTEC Level 1 (QCF) expectations for your centre. PSD, Workskills (Level 1 & 2) Life Skills years).BTEC Specialist (Level 1-3)* BTEC Professional (Level 4-7)* BTEC qualification Internal ungraded unit (‘Pass/fail’) We reviewed the information you submitted to us (actual unit grades and CAG) against our
