Jeep Liberty 3-Wheel Stroller JL031 Instructions
Jeep Liberty 3-Wheel StrollerInstruction SheetInstrucciones para carriola de 3 ruedasJeep LibertyFeuillet d'Instructions pour Poussetteà Trois Roues pour Jeep Liberty 2009 Kolcraft Enterprises, Inc.S77-T-R311/08
WARNINGAvoid serious injury from falling or sliding out. Always use Restraint System.Your child's safety depends on you. Proper stroller use cannot be assuredunless you follow these instructions. DO NOT USE STROLLER UNTIL YOUREAD AND UNDERSTAND THESE INSTRUCTIONS.IMPORTANT SAFETY INFORMATION:How to Keep Your Child Safe While Using this Stroller Adult Assembly Required. NEVER LEAVE YOUR CHILD UNATTENDED WHILE IN STROLLER.Accidents can happen quickly while your back is turned. You mustalways keep your child in view while your child is in the stroller,even when sleeping. Do not use this product as a bed. Your childmay become tangled in straps or pads and suffocate. Always use restraint system to keep child from standing up orfalling out of the stroller. Do not use product without full 5-pointHarness Restraint. Removing the shoulder straps will notadequately restrain child. Always lock the stroller open before allowing your child in or nearthe stroller. This prevents injuries caused by stroller collapsing. Only use this stroller with children who weigh less than 40 lbs. (18.1kg) or are less than 40” (1 meter) tall, and who’s head rests below thetop of the seat back. Use by larger children may damage the stroller,or cause a hazardous unstable condition to exist. Use this stroller in the reclined position until child can sit up unassisted. Always set the wheel brakes when stroller is not moving, especiallyon an incline. This prevents the stroller from rolling away. Always fasten the canopy onto the seat back when using thestroller in the reclined position.What to Avoid While Using this Stroller Always balance the weight of the stroller evenly. To prevent thestroller from becoming unstable or tipping: Do not place parcels or accessory items on the stroller canopy,seat, or over the handle. Do not put more than 10 lbs. (4.54 kg) in the basket. Do not put more than 2.5 lbs. (1.13 kg) in each cargo bag (select models).2Continued on next page
DO NOT place more than 3 lbs.(1.36 kg) in the parent tray to avoidtipping! Do not allow children to play with or hang onto the stroller. Never use this stroller on stairways or escalators. DO NOT lift by tray or toys. Make sure children are clear of any moving parts if you adjust thestroller, otherwise they may be injured. THIS IS NOT AN EXERCISE STROLLER! Do not use this productwhile running, jogging, in-line skating or participating in otherathletic activities. DO NOT put child in basket. Reflectors are for decorative purpose only. Take care when folding and unfolding to prevent finger pinching. Product may become unstable if a parcel bag, other than the onerecommended by the manufacturer is used. DO NOT allow children to climb into stroller unassisted. Strollermay tip over and injure child. Keep air filled wheels at a recommended tire pressure of 30 p.s.i.(210 kPa) (select models). Only use replacement parts supplied by the manufacturer. If youhave a flat air filled tire, you may use a standard bicycle tire repairkit or take it to a bicycle shop to be repaired. (Select Models)How to Use this Stroller with Your Infant Car Seat AVOID SERIOUS INJURY FROM FALLS: This product is only to be used with certain Infant Car Seats. See belowfor list of compatible Infant Car Seats. When using this product with your Infant Car Seat, infant must alwaysbe secured in the car seat with the car seat harness. To ensure your Infant Car Seat is properly installed on the stroller,make sure it is: Facing the person pushing the stroller. Tightly secure to the stroller with the car seat restraint straps. If at any time your Infant Car Seat does not secure properly to thestroller, or if you have questions about assembly or use of the stroller,Do Not use this product. Call Kolcraft at 1-800-453-7673. Only transport infants that are within the size and weight limitations ofyour Infant Car Seat, as described in the instruction manual providedby the Infant Car Seat manufacturer.Continued on next page3
THE FOLLOWING INFANT CAR SEATS CAN BE USED WITH THIS STROLLER: Britax Companion Chicco Key Fit & Key Fit 30 Graco Snug Ride Series Graco Safe Seat Peg Pérego Primo Viaggio SIP If your Infant Car Seat is not one of the models listed above, DONOT use your infant car seat with this stroller. Other Infant CarSeat models will not fit properly and may result in serious injury toyour child.Britax , Chicco , Graco , and Peg Pérego are trademarks of theirrespective owners. They are not associated with Kolcraft Enterprises, Inc. and no approval by them is to be implied.Parts ListStroller FrameRear Wheels (2)Air FilledCargo Bags (2)(Select Models)Front Tray(Select Models)Front WheelAir Filled(Select Models)Basic Parent Tray(Select Models)Rear Wheels (2)EVAFront WheelEVA(Select Models)(Select Models)iBaby Parent Tray(Select Models)Front WheelAssemblyiBaby (Select Models)Electronic Toys(Select Models)1” Screws (2)Non Electronic Toys(Select Models)Brake Assemblywith Rear AxelCotter Pins (2)Tool Needed: Phillips Screwdriver4Hub Caps (2)Washers (2)
How to Assemble Your StrollerTo Open Stroller1 Remove any cardboard inserts or plasticties used to protect the product duringshipment.22 Release the locking latch.3 Unfold, making sure both side locks snapinto place.To Assemble Rear WheelsRemove and discard protective plastic1 sleevefrom ends of brake assembly with2rear axle. Place stroller on floor with seatfacing down.2 Position brake assembly with rear axle asshown, with brake levers pointingtowards stroller handle.3 Push both sides of brake assembly ontorear leg tubes at the same time untilspring loaded buttons click into place.NOTE: Make sure that spring loadedbuttons pop through.4CAUTION: If spring loaded buttons DONOT pop through, front wheel assemblycould fall off during use.4 Slide a rear wheel onto the axle thenslide a washer onto the axle.55 Fit straight part of cotter pin throughhole on axle as shown.Line up each of the tabs in the hub cap6 withthe slots in the wheel, snap hub capinto place.7 Repeat for second side.5
To Assemble Front Wheel Tube1 Place stroller so the handle bar and rearwheels are touching the floor.2 Position front wheel assembly over2plastic side housings.Side Housing3 Align tubes with plastic housings andpush front wheel assembly on the frame.You may need to depress the springloaded buttons slightly while assemblingthe tubes.NOTE: If your spring loaded buttonbecomes out of place, take pliers andfeed button into hole.NOTE: Make sure that spring loadedbuttons pop through.3CAUTION: If spring loaded buttons DONOT pop through, front wheel assemblycould fall off during use.Secure Front Wheel Tube to the front4 frametubes using screws. The screwsshould be aligned into the 2 holeslocated on the underside of plasticside housing. Secure with a Phillipsscrewdriver on both sides.46
To Attach Front Wheel1 Discard plastic protective bar at the endof stroller fork. Align front wheel axlewith cutouts in the front wheel fork. Youmay need to loosen the nuts on bothend of the axle in order to make roomfor the front wheel fork.12 Ensure that the tab on the tear dropshaped washer is aligned with the holeon the front fork as shown. Tighten nutwith wrench. Repeat for other side.2To Attach Storage Basket1 Secure rear portion of the fabric storagebasket by snapping the basket aroundcargo tube.12 Fasten velcro strap on side of storagebasket to seat tube. Repeat on oppositeside.27
To Attach Cargo Bags (select models)WARNINGDO NOT put more than 2.5 lbs.(1.13 kg) in each cargo bag.11 To attach cargo bags, feed and secureone end of Velcro strap through slot onthe plastic side housings.2 Secure other side of cargo bag tovertical support tube using velcro straps.To Attach Front Trayposts on tray with receptacles on1 Alignplastic side housings.2 Push until each side clicks in place.1release, push one button and swivel3 Totray.38
To Install Batteries in Electronic Toys (select models)insert batteries, use a Phillips head1 Toscrewdriver to unfasten battery cover.Insert batteries as shown. Requires 2“AA” batteries (Not Included). Securebattery cover.12 Turn switch on ‘II’ to play sounds. To turnO’.off, move switch to ‘OCAUTION: Do not mix old and newbatteries. Do not mix alkaline, standard(carbon-zinc) or rechargeable (nickelcadmium). Remove battery(ies) beforestoring this product for a prolongedperiod of time.To Attach Toys (select models)1 Place toy so that they face the child inthe stroller.22 Align tabs on back of toy with slots inchild tray.down firmly on toy until front and3 Pressback tabs lock toy securely in place.44 To remove toy from tray, pull front wall oftoy toward seat and rotate toy upwarduntil rear tabs release.9
To Install Batteries into iBaby (select models)Requires 4 “AAA” Batteries (Not Included).Use a Phillips screwdriver to remove the1 batterydoor.1Place batteries in the compartment2 followingpolararity directions.Screw the battery door back onto the3 unit and replace the foam.To Attach Parent TrayWARNINGDO NOT place more than 3 lbs.(1.36 kg) in this tray to avoid tipping!DO NOT place hot liquids in this tray.Hot liquids can burn your child.tray holes with posts near handle1 Alignand snap on.TO REMOVE, pull each side up and out.For cleaning, parent tray is top rackdishwasher safe.Install iBaby Sound System (select models)WARNING1 Loud volume can damage your child’s hearing. Whenturning on music, gradually adjust the volume to acomfortable listening level so child is not startled. Do not place hot liquids in this tray. Hot liquids canburn your child.To attach iBaby , align device over center1 compartment of iBaby parent tray. Pushdown to snap into place.2To remove iBaby , with one hand2 depressbutton on rear of device andlift device up with other hand.10
How to Properly Use Your New StrollerTo Operate BrakesTO LOCK BRAKE: Push both brakes1 downto lock wheels.UnlockLockTEST: Push stroller slightly to make surebrakes are engaged.2 TO UNLOCK BRAKE: Lift up on brakes.To Secure Child In StrollerWARNINGAvoid serious injury from falling or slidingout. Always use restraint system. Do notuse product without full 5-point HarnessRestraint. Removing the shoulder strapswill not adequately restrain child.3both foot brakes to keep stroller1 Lockfrom rolling.2 Place child in stroller.43 Hook shoulder straps to waist belt.4 To fasten restraint system buckles - pushtogether. Be sure both buckles arefastened to secure child safely.65 To unsnap restraint system buckles press tabs to release.Adjust RestraintSystem Harnessproper fit, adjust shoulder straps and6 Forwaist band as shown.11
Car Seat Restraint Storagebelts for the Infant Car Seat are1 Restraintred and are located in the small pocketson each side of the stroller seat.1Restraint beltsCAUTION: When not using your redinfant car seat restraint belts, store theminside pocket. Failure to store restraintbelts may cause strangulation.To Install Car SeatBelow is a list of car seats that will fit on the Jeep Liberty 3-Wheel Stroller. If your Infant CarSeat is not one of the models listed below, DO NOT use your infant car seat with this stroller.Other Infant Car Seat models will not fit properly and may result in serious injury to your child. Britax Companion Chicco Key Fit & Key Fit 30 Graco Snug Ride Series Graco Safe Seat Peg Pérego Primo Viaggio SIP 1 Recline stroller seat first and push canopyback.2 Place car seat in seating area of strollerso that child is facing handle of stroller.Make sure the car seat is resting againstfront tray and that the car seat is level.Your child’s head should be slightlyabove their knees. Do not let infant carseat sit on top of tray.2N O T E : Your Infant Car Seat may have alevel indicator. It is not necessary foruse with this stroller and the indicatormay fall outside the recommendedarea. The level indicator is for use whilethe Infant Car Seat is in an automobile.XThread RED infant car seat restraint belts3 locatedin the side pockets through theclips on the top of the car seat.3NOTE: Some car seats do not have clips.Secure belt over lowest point of carseat.12Continued on next page
4 Tighten belt as much as you can tosecure infant car seat (see TO SECUREINFANT CAR SEAT section). Fastenbuckle.4ensure your Infant Car Seat is secure,5 Topull up on shell of car seat by child’s feet.Infant Car Seat should not move morethan 1/4 of an inch. If it becomes loose,repeat Step 3. DO NOT use this productwith your Infant Car Seat if it moves morethan 1/4”. Serious injury or death mayresult from poor installation.To Secure Infant Car Seat2Lock both foot brakes to keep stroller1 fromrolling.To fasten car seat restraint belts - open2 uploop of the restraint belt. Adjust beltuntil the buckles almost touch.334Pull end tab of restraint belt to set.3 Pushbuckles together to secure.4 To unsnap Restraint Belt - press tabs.13
To Recline Seatavoid finger entrapment or pinching, do not adjustseat back while child is in the stroller. To avoid headWARNING Totheentrapment, always fasten the canopy to the seat backwhen using the stroller in the reclined position.1 To recline seat back, loosen belt.2 To raise seat back, tighten belt.To Operate Swivel Wheel LockLOCK FRONT SWIVEL: Adjust front1 wheelso that wheel is straight and lockis forward. Push lock to right.UNLOCK FRONT SWIVEL: Push lock to2 left.NOTE: On rough surfaces, lock thewheel to keep straight. On smoothsurfaces, unlock to allow the wheel toswivel.To Operate iBaby (select models) 1 Connect the iBaby plug to the head-phone jack of your personal sound system (iPod ** or MP3 player).Turn on iBaby by locating the power button2 asshown. A red light will indicate that the1power is on.3 To avoid startling your child, adjustvolume on your personal sound systemto its lowest level. Turn on your personalsound system and slowly increasevolume to a comfortable listening levelfor you and your child.NOTE: If sound cuts out or becomes distorted, check your personal sound system batterylevel. If battery level is okay and sound is stilldistorted, replace iBaby’s batteries. DO NOTleave iBaby in a hot car or outside in the rain.For use with iPhone a seperate jack adaptercan be purchased at Apple Retailers.214
To Adjust Shoulder Strap HeightLowerHigherNOTE: For a secure fit, straps should beat or below the child's shoulder. Adjuststraps to higher position as your childgrows.readjust shoulder restraints, unbuckle1 Toshoulder strap from waist strap. Removefabric shoulder sleeve.12 Feed and push buckle back through theslot that is currently used.the back of the seat locate the3 Onslot for higher position and pushbuckle through slot as shown. Repeatfor second side.24 Replace fabric shoulder sleeve andreattach shoulder strap to waist strap.315
To Fold Stroller4a1 Lock brakes.2 Recline seat fully.4b3 Close canopy.4 (A) Push and hold red button to left with(B) thenthumb to unlock positionsqueeze large red lever on handle tofold stroller.NOTE: If 1-Hand fold feature does notoperate properly, pull up latches onframe to fold.65 Push stroller down to fold.6 Engage locking latch.Care & Maintenance To keep your stroller running smoothly and avoid squeaking wheels use a silicone or graphitebased lubricant. It is important to get it into the axle and the wheel assembly. Clean metal parts with a damp cloth and wipe dry. Clean woven fabric or vinyl parts with mild soap and water solution. Dry wet stroller with a soft cloth to prevent rusting. When storing stroller, never stack other items on top of it; this may damage the stroller. Periodically check for worn parts, loose screws, torn materials or stitching. Replace any damaged parts immediately.**iPod is a registered trademark of Apple Computer, Inc.Apple Computer, Inc. is not associated with Kolcraft Enterprises, Inc. or Jeep and noapproval by them is to be implied.16
Limited WarrantyJeep is a registered trademark of Chrysler LLC and is used under license by Kolcraft . Chrysler LLC 2009.Kolcraft warrants this product to be free of defects in materials and workmanship, as follows:For a period of ONE YEAR from the date of purchase, Kolcraft will repair or replace, at itsoption, the defective product. If you have a problem or are not satisfied with this product,please contact the Consumer Service Department at Kolcraft.REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVEREMEDY OF THE CONSUMER. KOLCRAFT SHALL NOT BE LIABLE FOR ANY INCIDENTALOR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT, EXCEPT TO THE EXTENT REQUIRED BY APPLICABLE LAW. ANYIMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSEON THIS PRODUCT IS LIMITED TO THE DURATION OF THIS WARRANTY.Some states do not allow the exclusion or limitation of warranties set forth above, so theabove exclusions may not apply to you. This warranty gives you specific legal rights, and youmay also have other rights which vary from state to state. We sincerely thank you for yourpurchase of this Kolcraft product.To obtain warranty service, please call Kolcraft’s Consumer Service Department at1-800-453-7673 in U.S. and Canada, 1-910-944-9345 outside U.S. and Canada or contact usvia email at customerservice@kolcraft.comIf the product is returned to Kolcraft’s Consumer Service Department for repair orreplacement, it must be shipped prepaid and adequately insured.For further information visit www.kolcraft.comRecall WEBSITE: HELP KEEP YOUR CHILD SAFE. Check www.recall.gov to see if anyproducts you use with your child or any of your child's toys have been recalled.Personal Record CardOnce in a while, we are less than perfect and one of our products reaches a customer witha problem. In most cases, we can solve your problem with replacement parts. Pleasecontact us before you return one of our products to the store. Once a product is returned,it cannot be resold. The materials and the energy used to make it are wasted.Please fill in the information in the space provided and attach a copy of your purchasereceipt. You will need this information to obtain warranty service.You can find the Model Number and Date of Manufacture on a sticker located on the rearstroller leg, or sewn on the back of the seat.Please direct any comments, questions or replacement part requests to:Kolcraft Enterprises, Inc. Consumer Service Department10832 NC Highway 211EastAberdeen, NC 283151-800-453-7673 in U.S. & Canada, 1-910-944-9345 outside U.S. & CanadaEastern Standard Time, 8 am-6:45 pm Monday - Thursday, 8 am-3:30 pm Fridayfax: 910-944-3490e-mail: customerservice@kolcraft.comModel / Style Number:Date of Manufacture:Date of Purchase:17Turn to page 51 to see a list ofreplacement parts
ADVERTENCIAEvite daños serios causados por caídas o al deslizarse del asiento. Siempreuse el sistema de cinturones. La seguridad de su hijo/a depende de usted.No se puede asegurar un uso apropiado de la carriola a menos que ustedsiga estas instrucciones. NO USE LA CARRIOLA HASTA QUE USTED HAYALEÍDO Y COMPRENDIDO ÉSTAS INSTRUCCIONES.INFORMACIÓN IMPORTANTE DE SEGURIDAD:Cómo mantener a su hijo seguro mientras utiliza ésta carriola Ensamblado por un Adulto es necesario. NUNCA DEJE A SU NIÑO SOLO EN LA CARRIOLA. Pueden ocurriraccidentes repentinamente mientras usted se encuentra de espaldas.Debe mantener a su niño siempre a la vista minetras esté en lacarriola, aunque esté durmiendo. No utilice esté producto comocama. Su niño pudiera quedar atrapado entre las correas o sofocarsecon los colchoncitos. Siempre use el sistema de sujeción para evitar que su niño se pareen la carriola o se caiga. No utilice el producto sin un arnés desujección de 5 puntos. Si remueve los ajustes de los hombr
Jeep Liberty Feuilletd'InstructionspourPoussette . kit or take it to a bicycle shop to be repaired. (Select Models) How to Use this Stroller with Your Infant Car Seat AVOID SERIOUS INJURY FROM FALLS: This product is only to be used with certain Infant Car Seats. See below for list of compatible Infant Car Seats.
WARNING: WHEN A CHILD IS IN THE STROLLER KEEP THE CHILD TRAY ATTACHED TO THE ADAPTORS AT ALL TIMES. F Stand beside of the stroller & pull the fabric back from the sides of the stroller to expose the stroller hinge. Take one chld tray adapter at a time & insert the adaptor into the stroller hinge as shown.
used. ! Never use stroller on stairs or escalators.! Keep away from high temperature objects, liquids, and electronics.! Never allow your child to stand on the stroller or sit in the stroller with head toward front of stroller. ! Never place the stroller on roads, slopes or dangerous areas.! Do make sure all mechanisms are fixed before using .
stroller. TO PREVENT STROLLER FROM BEING IN A HAZARDOUS . UNSTABLE CONDITION, never place parcels or other items on the stroller handle or canopy. DO NOT. place more than 10lbs (4.5 kg) in the storage basket. TO AVOID STRESS AND TO . PREVENT A HAZARDOUS UNSTABLE CONDITION ON STROLLER, stroller is intended for a child who weighs up to 45lbs (20 .
the stroller. This prevents injuries caused by stroller collapsing. † Only use this stroller with children who weigh less than 40 lbs. (18.14 kg). Use by larger children may damage the stroller, or cause a hazardous unstable cond
Tandem Stroller Instructions . stroller, or if you have questions about assembly or use of the stroller, Do Notuse this product. Call Kolcraft at 1-800-453-7673. † Make sure the stroller is fully unfolded and securely latched
stroller with head toward front of stroller. NEVER ALLOW YOUR STROLLER to be used as a toy. STROLLER TO BE USED only at walking speed. Product not intended for use while jogging, skating, etc. USING GRACO INFANT CAR SEAT WITH STROLLER: USE ONLY A GRACO SNUGRIDE , SNU
Do not leave pet unsupervised in the stroller. Before making adjustments to the stroller ensure that the pet’s body is clear of any moving parts. Do not hang bags from handles as this may cause the product to become unstable. Do not use on escalator or stairs; fold the stroller and carry. Put on brake whenever you park the stroller.
Jan 30, 2019 · ness is not used. ! Never use stroller on stairs or escalators.! Keep away from high temperature objects, liquids, and elec-tronics.! Never allow your child to stand on the stroller or sit in the stroller with head toward front of stroller. ! Never place the
