VNC1045-DBJ - Esxnavi.de
3.1NIOT1AVLL IDEAT US GINVNC1045-DBJ1
IMPORTANT NOTESThis guide is an aid for the professional installation of the device.Please note the following notes before installation: Always handle all parts of the device and the components of your vehicle withcare. Under all circumstances observe the regulations of the vehicle manufacturerand do not make any changes to the vehicle which could impair driving safety. For safety reasons, disconnect the vehicle battery’s ground connection beforeinstallation. Please always pay attention to the correct polarity of the connections. Please do not modify any harnesses or connections of the device or the vehicleas this may affect the warranty. Make sure that no cables are squashed or cause a short circuit. Do not lay cables in front of the airbags, e.g. in the dashboard or in a way thataffects their function.2
RECOMMENDED TOOLS:Ø 20 mmUnlock devicesPlastic mounting wedgesPlastic drillCable tiesPhillips screwdriver or bitTorx screwdriver or bitRECOMMENDED ACCESSORIES:Steering wheel control adapters:VNA-LFB-FD2FIAT DUCATO IV, PEUGEOT BOXER III, CITROËN JUMPER III (Type 290, since2015) with radio preparation, ISO connectionVNA-LFB-FD3FIAT DUCATO IV, PEUGEOT BOXER III, CITROËN JUMPER III (Type 290, since2015) with original radio or original navigation system, CAN bus (52-PIN), USB port(optional), AUX port (optional)VNA-LFB-FD4FIAT DUCATO IV, PEUGEOT BOXER III, CITROËN JUMPER III (Type 290, since2015) with original radio Delphi F250, ISO connectorVNA-LFB-FD5 (included)FIAT DUCATO III, PEUGEOT BOXER II, CITROËN JUMPER II (Type 250, 2006 2015) ISO connection3
INSTALLATION GUIDEOnly with radio ex-factory:Pull the radio out of the slotusing the release tools.Only with radio ex-factory:Remove the connectors on the back of the radio.Only with radio ex-factory:Loosen the 4 screws.Loosen the 2 screws underneath.Open the storage tray and loosen the 2screws.Pull the storage tray upwards.4
INSTALLATION GUIDELoosen the 2 screws underneath.Remove the ventilation ducts on the left andright with a screwdriver and leverage asshown.The dashboard should now look like this. Loosen the 2 screws.Lift the rubber tray and remove the screw underneath.5
INSTALLATION GUIDERemove the original panel.Release the plugs.Loosen the 2 screws.Remove the original panelby lifting it and pulling itforward.PRELIMINARY6
INSTALLATION GUIDERemove all marked clips from theoriginal panel and attach them tothe supplied enclosed panel.Pull the cover out from back to top (asshown).Loosen the 2 screws.Loosen the 2 screws and put the speedometer display on top (The plugs can stay). 1x ScrewLoosen the screws on the left side below thesteering wheel.Loosen the screw on the right side below thesteering wheel.7
INSTALLATION GUIDEThen install the supplied enclosed panel,where the GPS antenna is integrated.Pay attention to the GPS cable and fasten the2 screws.Then insert the cable of the GPS antenna tothe device and connect it to the GPS socketas described on page 14.Put in the storage tray and lift it, then attach the 2 screws.Attach the 2 screws on the front.8VNA-BTBOX connection* (optional):Remove the cover from the fuse box. Loosenthe screw.
INSTALLATION GUIDEVNA-BTBOX connection* (optional): Remove the cap of theconnector.VNA-BTBOX connection* (optional):Connect the supplied VNA-BTBOX connector.(like shown)Place the microphone.Lay the microphone cableas shown.(Picture shows cable with factory installed radio)(Picture shows cable without factory installed radio)VNA-BTBOX connection* (optional):Lay the VNA-BTBOX connection cable.Connect the respective cables to the ESX device as described from page 14 on.* Optional accessories9
INSTALLATION GUIDEPut in the speedometer display and the cover.Slide the ESX device into the slot.Attach the screws.ESX device after the installation.Attach the screw and set in the rubber tray.10
STEERING WHEEL CONTROL (optional adapter required)Steering wheel control - teaching multifunction buttonsSwitch to the system settings of the device and select „Steering wheel control“.Then the following menu appears:Press at first on “RESET”. Then press on the desired function and then on the regarding buttonon the multifunction steering wheel via which this function is to be controlled. After you havesuccessfully assigned a function, the field is highlighted.11
SCOPE OF DELIVERYITEM12IMAGEAMOUNTMain Device1Panel incl. GPS Antenna1MicroSD Memory Card 8 GBNavigation Software1Remote Controller1Microphone1DAB Box1
SCOPE OF DELIVERYITEMIMAGEAMOUNTAntenna Splitter (active) forFM/DAB Radio Reception1DAB Wiring1Audio Cables1Camera/AUX/Video Cables1Video Cables1USB Extension1System Cable1Steering Wheel Control Adapter1Video Box(Camera relay)113
WIRING DIAGRAM14
WIRING DIAGRAM DAB BOXSWCSteeringwheel controlAMP TURNVEHICLEANTENNAOPTIONALANTENNA SPLITTER (ACTIVE)FOR FM/DAB RADIO RECEPTION 12 V15
CONNECTION CAMERASRear View CameraVIDEO BOXGNDREVERSETRIGGERREVERSE CAMERA POWERFRONT CAMERA INNOTE: The reverse gear signal mustbe connected to the green REVERSEcable in the ISO connector A3.REVERSE CAMERA INExample: VNA-RCAM-SHUTTERDual Lens Camera 1VIDEO BOXGNDREVERSE CAMERA POWERCutcableFRONT CAMERA INREVERSE CAMERA INInsulate the opencable end and protect itagainst short circuit!Connect together with the signal cablefrom the reverse gear of the green REVERSE cable in the ISO connector A3.Example: VNA-RCAM-DUALSHUTTERConnect the camera power supply to the ignitionplus in the ISO connector A7.16REVERSETRIGGER
CONNECTION CAMERASDual Lens Camera 2VIDEO BOXGNDREVERSE CAMERA POWERCutcableREVERSETRIGGERFRONT CAMERA INREVERSE CAMERA INInsulate the opencable end and protect itagainst short circuit!Connect together with the signal cablefrom the reverse gear of the green REVERSE cable in the ISO connector A3.Example: VNA-RCAM-DBJ200Connect the camera power supply to the ignitionplus in the ISO connector A7.17
CONNECTION CAMERASDual Lens Camera 3VIDEO BOXGNDREVERSE CAMERA POWERCutcableFRONT CAMERA INREVERSE CAMERA INInsulate the opencable end and protect itagainst short circuit!Connect together with the signal cablefrom the reverse gear of the green REVERSE cable in the ISO connector A3.Example: VNA-RCAM-CS220Connect the camera power supply to the ignitionplus in the ISO connector A7.18REVERSETRIGGER
NOTES19
DESIGNESX Car Media Systems · Audio Design GmbHAm Breilingsweg 3 · D-76709 Kronau/GermanyTel. 49 7253 - 9465-0 · Fax 49 7253 - 946510www.esxnavi.de - www.audiodesign.de 2019 All Rights Reserved / Alle Rechte vorbehaltenReprinting and reproduction, even in part, is prohibited.
Put in the storage tray and lift it, then attach the 2 screws. Then install the supplied enclosed panel, where the GPS antenna is integrated. Pay attention to the GPS cable and fasten the 2 screws. Then insert the cable of the GPS antenna to the device and connect it to the GPS socket as described on page 14. Attach the 2 screws on the front.
for a portable roll up version of this antenna for backpacking or ARES. This paper describes how the principles of the DBJ-1 can be extended to a portable roll-up antenna. Since it is the second version of this antenna, it will be referred to as the DBJ-2. Principles of the DBJ-1 The DBJ-1
Ed Fong, WB6IQN The TBJ-1 – A tri-band base antenna The May meeting speaker will be Ed Fong (WB6IQN). As many of you know, he is the inventor of the DBJ-1 and DBJ-2 antenna that was featured in the February 2003 and March 2007 QST. The DBJ-1 is a highly effective du-al band VHF/UHF base station a
Creating the Dual-Band DBJ-1 So how can one add UHF to the con-ventional 2-meter J-Pole? First of all, a half-wave 2 meter antenna does resonate at UHF. Resonating is one thing, but work-ing well is another. The DBJ-1 not only resonates, but also performs
Our guest speaker for the May meeting will be Ed Fong WB6IQN. As many of you know, he is the inventor of the DBJ-1 and DBJ-2 antenna that was featured in the February 2003 and March 2007 QST. His latest article in QST was the TBJ-1 – a triband base antenna published in
presented by Ed Fong, WB6IQN. After a break, the second part will allow Ed to finish his program if necessary, and allow time for club announcements, questions and comments. As many of you know, Ed is the inventor of the DBJ-1 and DBJ-2 antenna t
Dualband Roll-up J-pole Antenna by Jason Bowman, WG8B Jason’s presentation will include a discussion with Edison Fong on his design of the DBJ-1 and DBJ-2 roll-up J-pole antennas. These are roll-up J-pole antennas that are designed to work on both VHF and UHF amateur bands. A typical
The DBJ-1 and DBJ-2 are Dual-band (144-148 MHz and 440-450 MHz) vertical and roll-up antennas. The TBJ-1 is the triband, verti-cal antenna for 2m / 1.25m(220 MHz) / 70cm. (Patent #9 608 336) (Continued on page 2) Wow, here we in Feburary already, don’t for-get about valentines day guys! I hope every body was able to survive the high winds we
Business Studies Notes Year 9 & 10 Chapter 1 The purpose of Business Activity A NEED is a good or service essential for living (food, water, shelter, education etc.). A WANT on the other hand is something we would like to have but is not essential for living (computer games, designer clothing, cars etc.). people’s wants are unlimited. The Economic Problem results from an unlimited amount of .
