AII37653 2008 Civic 2-4dr Interior . - Bernardi Parts Honda

2y ago
22 Views
2 Downloads
531.94 KB
13 Pages
Last View : 2m ago
Last Download : 2m ago
Upload by : Mya Leung
Transcription

OR ILLUMINATIONP/N 08E10-SNA-1002008 CIVIC2- AND 4-DOORNOTE: The interior illumination lights cannot beinstalled on 2-door vehicles equipped with fog lights.Publications No.All 37653Issue DateAUG 20073 ScrewsPARTS LISTInterior illumination light(with blue tape)2 Interior illumination lights(with white tape)Interior illumination lightharnessBracketWire tie with clip3 Flange nutsSwitchTemplateFuse label10 Wire tiesEPT sealerSwitch trim2 Switch lids 2007 American Honda Motor Co., Inc. - All Rights Reserved.AII 37653 (0708)08E10-SNA-1000-911 of 13

Illustration of the Interior Illumination LightsInstalled on the Vehicle3.INTERIOR ILLUMINATIONLIGHT HARNESSIf equipped, remove the driver’s dashboard undercover (turn the knob counterclockwise, and releasetwo clips and pin).FUSE CASE (2A)PINSWITCHINTERIORILLUMINATIONLIGHT(with white tape)INTERIORILLUMINATIONLIGHT(with white tape)INTERIORILLUMINATIONLIGHT(with blue tape)5306010T2 CLIPSDRIVER’SDASHBOARDUNDER COVERTOOLS AND SUPPLIES REQUIREDPhillips screwdriverFlat-tip screwdriverRatchet10 mm SocketKNOB5202112T4.Remove the driver’s dashboard lower cover (eightclips).DrillDrill bits (3 mm, 5 mm, and 10 mm)FilePushpinUtility knifeScissorsPiece of steel wireElectrical tapeAdhesive tapeEye protection (face shield, safety goggles, etc.)8 CLIPSScaleShop towelDRIVER’SDASHBOARDLOWER COVERINSTALLATIONCustomer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These proceduresshould not be attempted by “do-it-yourselfers.”1.Make sure you have the anti-theft code for theradio, then write down the radio station presets.2.Disconnect the negative cable from the battery.2 of 135202121TAII 37653 (0708) 2007 American Honda Motor Co., Inc. - All Rights Reserved.

5.Lower the tilt lever, and move the steering wheelto its lowest position. After moving the steeringwheel, return the tilt lever to its original position.COMBINATIONLIGHT SWITCHSHOPTOWEL8.Shift to “S” or “2”, and remove the lid from thedashboard center lower cover (four retaining tabs).WIPER/ WASHERSWITCHSHIFT LEVER(“S” or “2” position)DASHBOARD CENTERLOWER COVERSHOPTOWELSTEERINGWHEELSHIFTLEVERTILTLEVERLID4 RETAININGTABS9.5306371T6.Cover the combination light switch, wiper/washerswitch, and shift lever with a shop towel to protectthem from damage.7.Apply masking tape to the dashboard. Removethe instrument panel (one self-tapping screw and11 clips), and unplug the vehicle connector.INSTRUMENTPANEL5202130TRemove the passenger’s dashboard under cover(four clips and two pins).MASKINGTAPE2 PINSPASSENGER’SDASHBOARDUNDER COVER5306360T4 CLIPSVEHICLECONNECTORSELFTAPPINGSCREW11 CLIPS 2007 American Honda Motor Co., Inc. - All Rights Reserved.5624100BAII 37653 (0708)3 of 13

10. Remove the two bolts. Open the glove box, pushinward on the stoppers, and remove the glove box.13. Plug the interior illumination light harness 6-pinconnector into the fuse box 6-pin connector.6-PINCONNECTORCONNECTINGPORTSTOPPERFUSE BOXGLOVE BOX5202260TBOLTSRouting the Interior Illumination Light Harness11. Route the interior illumination light harness 5-pinconnector behind the fuse box, and pull it outthrough the opening of the air duct.INTERIORILLUMINATION LIGHTHARNESS 5-PINCONNECTOR5306033TINTERIOR ILLUMINATIONLIGHT HARNESS 6-PINCONNECTORNOTE: If another accessory is already plugged intothe 6-pin connector, remove the dummy connectorfrom the other accessory harness, and plug the interiorillumination light harness into that connector.BRANCH OFINTERIORILLUMINATIONLIGHT HARNESSOTHER ACCESSORYHARNESS 6-PINCONNECTORWIRE TIE100 mmFUSE BOXOPENINGOF AIRDUCTDUMMYCONNECTOR(Discard.)BRANCHOF VEHICLEHARNESSINTERIORILLUMINATIONLIGHTHARNESSFUSE BOXINTERIOR ILLUMINATIONLIGHT HARNESS 6-PINCONNECTORINTERIORILLUMINATIONLIGHT HARNESS6-PIN CONNECTOR5213100T5306025T12. Measure the vehicle harness from the point ofbranch as shown. Secure the interior illuminationlight harness (6-pin connector side) to the vehicleharness with one wire tie.4 of 13AII 37653 (0708) 2007 American Honda Motor Co., Inc. - All Rights Reserved.

14. Route the two interior illumination light harness 2pin connectors onto the right side of the vehiclealong the vehicle harness.FUSE LABEL(INTERIORILLUMINATIONLIGHT 2A)INTERIORILLUMINATIONLIGHT HARNESS2-PINCONNECTOR17. Route the wire through the opening for the lid ofthe dashboard center lower cover, and wind it ontothe interior illumination light harness 2-pinconnector (long harness side).ELECTRICALTAPESTEEL WIREFUSE LLUMINATIONLIGHT HARNESS5306050TGROUNDTERMINALINTERIOR ILLUMINATIONLIGHT HARNESS 2-PINCONNECTOR5306043T15. Attach the 2A fuse label to the interior illuminationlight harness fuse case.16. Remove the ground bolt from the vehicle. Securethe interior illumination light harness groundterminal with the ground bolt you just removed.18. Secure the other 2-pin connector to the interiorillumination light harness with electrical tape.19. Pull the interior illumination light harness out ofthe lid opening of the dashboard center lowercover by pulling the wire.STEEL WIREINTERIORILLUMINATIONLIGHT HARNESSELECTRICALTAPE5306060T20. Remove the wire and electrical tape from theinterior illumination light harness. 2007 American Honda Motor Co., Inc. - All Rights Reserved.AII 37653 (0708)5 of 13

21. Route the interior illumination light harness 2-pinconnector to the passenger’s side along thevehicle harness.23. Secure the interior illumination light harness to thevehicle harness with three wire ties.WIRE TIEOPENING INGLOVE BOXVEHICLEHARNESSINTERIORILLUMINATIONLIGHT HARNESS2-PIN CONNECTOR5306070T22. Secure the interior illumination light harness to thevehicle harness with two wire ties.VEHICLEHARNESSINTERIORILLUMINATIONLIGHT HARNESS5306090T24. Secure the interior illumination light harness to thevehicle harness using four wire ties if the vehicleis equipped with the driver’s dashboard undercover. Use three wire ties if the vehicle is withoutthe driver’s dashboard under cover.INTERIORILLUMINATIONLIGHT HARNESSWIRE TIEINTERIORILLUMINATIONLIGHTHARNESSWIRE TIEVEHICLEHARNESSFUSE BOX6 of 13WIRE TIE(Vehicle withWIREdriver’s dashboard TIEunder cover only)5306082TAII 37653 (0708)5306100T 2007 American Honda Motor Co., Inc. - All Rights Reserved.

Installing the Interior Illumination Lights27. Secure template (A) to the driver’s dashboardunder cover with tape by aligning it with thesquare hole at the end of the curve as shown.25. Using scissors, cut out the template.CURVED ENDPUSHPINTEMPLATE (A)TEMPLATE5604340THOLEIf the vehicle is equipped without a driver’sdashboard under cover, go to step 34; otherwise,continue with step 26.26. Pull up the insulator on the driver’s dashboardunder cover, and cut into it as shown.DRIVER’SDASHBOARDUNDER COVER5306130T28. Using a pushpin, pierce the template at the threemarked points. Remove the template.29. While wearing eye protection, drill one 10 mm holeand two 5 mm holes at the pierced points on thedriver’s dashboard under cover. First drill with a3 mm bit, then finish with a 5 mm bit/10 mm bit asshown. Using a file, remove any burrs from theholes.60 mmDRILL(3 mmDRIVER’SDASHBOARDUNDER COVER5 mm drill bit)INSULATOR5306120TDRILL(3 mm 10 mmdrill bit)DRIVER’SDASHBOARDUNDER COVER5306140T 2007 American Honda Motor Co., Inc. - All Rights Reserved.AII 37653 (0708)7 of 13

30. Cut the rib of the driver’s dashboard under coveras shown. Using a file, remove any burrs from theedge.32. Bundle the interior light harness and secure theconnector to the bracket using a wire tie with clip.WIRE TIEWITH IVER’SDASHBOARDUNDER COVERDRIVER’S DASHBOARDUNDER COVER5306171T5306150T33. Reinstall the insulator to the driver’s dashboardunder cover, and pass the interior illumination lightconnector through the slit.31. Route one interior illumination light (with whitetape) connector through the 10 mm hole. Installthe interior light and bracket on the driver’sdashboard under cover with a screw and LUMINATIONLIGHT(with white tape)DRIVER’SDASHBOARDUNDER COVERSLITSCREW5306160T8 of 13AII 37653 (0708) 2007 American Honda Motor Co., Inc. - All Rights Reserved.

34. Position template (B) on the lid of the dashboardcenter lower cover.37. Route the interior illumination light (with blue tape)connector through the 10 mm hole. Install thecourtesy light on the lid with the screw and flangenut.PUSHPININTERIORLIGHTCONNECTORLID OFDASHBOARDCENTERLOWER LIGHT(with bluetape)SCREW5306200T5306180T35. Using a pushpin, pierce the template at the threemarked points. Remove the template.36. While wearing eye protection, drill one 10 mm holeand two 5 mm holes at the pierced points on thelid. First drill with a 3 mm bit, then finish with a 5mm bit/10 mm bit as shown. Using a file, removeany burrs from the holes.DRILL(3 mm5 mm drill bit)38. Using scissors, cut one EPT sealer into threeequal pieces and use one of the pieces to wraparound the interior illumination light connector.39. Secure template (C) to the passenger’s dashboardunder cover with tape by aligning it with the squarehole and the end of the curve as shown. Do notuse the marks on the inside of the passenger’sdashboard under cover.DRILL(3 mm 10 mmdrill R COVERLIDTEMPLATE(C)5306190T5306220T40. Using a pushpin, pierce the template at the threemarked points. Remove the template. 2007 American Honda Motor Co., Inc. - All Rights Reserved.AII 37653 (0708)9 of 13

41. While wearing eye protection, drill one 10 mm holeand two 5 mm holes at the pierced points on thepassenger’s dashboard under cover. First drill witha 3 mm bit, then finish with a 5 mm bit/10 mm bitas shown. Using a file, remove any burrs from theholes. Do not use the marks on the inside of thepassenger’s dashboard under cover.If the vehicle is equipped without a driver’sdashboard under cover, continue with steps 44 to47; otherwise, go to step 48.44. Assemble the interior illumination light (with whitetape) with the bracket using the screw and flangenut.VEHICLEBRACKETDRILL(3 mm 10 mmdrill bit)DRILL(3 mm 5 mmdrill bit)FLANGE NUTPASSENGER’SDASHBOARDUNDER COVERINTERIORILLUMINATIONLIGHT(with PPINGSCREW (Reused.)5306230T42. Route the interior illumination light (with whitetape) connector through the 10 mm hole. Installthe interior illumination light on the passenger’sdashboard under cover with the screw and flangenut.FLANGE CONNECTOR5306252T45. Remove the self-tapping screw from the vehiclebracket. Secure the bracket to the vehicle bracketusing the self-tapping screw that you just removed.PASSENGER’SDASHBOARDUNDER COVER46. Wrap the remaining piece of EPT sealer that youcut into three equal pieces around the interiorillumination light connector.47. Plug the interior illumination light connector intothe interior illumination light harness 2-pinconnector, and secure them to the interiorillumination light harness using a wire ORINTERIORLIGHT(with whitetape)SCREW5306241T43. Wrap another piece of the EPT sealer that you cutinto three equal pieces around the interiorillumination light connector.INTERIORILLUMINATIONLIGHT TORWIRE TIE5306303T10 of 13AII 37653 (0708) 2007 American Honda Motor Co., Inc. - All Rights Reserved.

If the vehicle is equipped with a instrument panelpocket, continue with step 48; otherwise, go tostep 51.51. Remove the switch lid from the instrument panel.48. Remove the pocket from the instrument panel(three self-tapping H LID(Discard.)INSTRUMENTPANEL5306330T52. Install the switch in the instrument panel.POCKET(Discard.)53. Plug the interior illumination light harness 5-pinconnector to the switch, and reinstall theinstrument panel.5306260T49. Install the switch trim to the instrument panel withthe three self-tapping T HARNESS5-PINCONNECTOR54. Reinstall the driver’s dashboard lower cover andglove box.SWITCHSWITCHTRIMSWITCHLID5306271T50. Install the switch and two switch lids to the switchtrim. Go to step 53. 2007 American Honda Motor Co., Inc. - All Rights Reserved.AII 37653 (0708)11 of 13

55. If equipped with the driver’s dashboard undercover, plug the interior illumination light harness 2pin connector to the interior illumination lightconnector on the driver’s dashboard under cover,and reinstall the under cover.57. Plug the interior illumination light harness 2-pinconnector to the interior illumination light connectoron the passenger’s dashboard under cover, andreinstall the under NATIONLIGHTCONNECTORINTERIOR ILLUMINATIONLIGHT HARNESS 2-PINCONNECTORDRIVER’SDASHBOARDUNDER COVER5306291TPASSENGER’S DASHBOARDUNDER COVER5306321T56. Plug the interior illumination light harness 2-pinconnector to the interior illumination lightconnector on the lid of the dashboard center lowercover, and reinstall the lid.INTERIORILLUMINATIONLIGHT HARNESS2-PINCONNECTORDASHBOARD CENTERLOWER COVER12 of 13INTERIORILLUMINATIONLIGHTCONNECTORLID5306310TAII 37653 (0708) 2007 American Honda Motor Co., Inc. - All Rights Reserved.

58. Check that all wire harnesses are routed properlyand all connectors are plugged in.HOW TO OPERATE59. Reinstall all removed parts. Check that all clipsand other fasteners are installed securely. Turn the headlight switch to the “ ” and “position (headlights on low beam). Press the courtesy light switch.”60. Reconnect the negative cable to the battery.61. Enter the customer’s radio anti-theft code, andreset the radio station presets.62. Reset the clock.NOTE: When the battery is disconnected, the driver’swindow AUTO function is disabled. Start the engine. Push down on the driver’swindow switch until the window is fully open.OFFPull up on the driver’s window switch to closethe window completely, then hold the switch fortwo seconds or more.COURTESYLIGHTSWITCH HEADLIGHT SWITCHLower and raise the driver’s window to check theoperation of the driver’s window AUTO function. 2007 American Honda Motor Co., Inc. - All Rights Reserved.ON-ONONOFF--5306340TAII 37653 (0708)13 of 13

46. Wrap the remaining piece of EPT sealer that you cut into three equal pieces around the interior illumination light connector. 47. Plug the interior illumination light connector into the interior illumination light harness 2-pin connector, and secure them to the interior illumination light

Related Documents:

Job #1: July, 2008 MAZDA3i Sport 4DR MAZDA3i Touring Value 4DR MAZDA3s Sport 4DR MAZDA3s Touring 4DR MAZDA3s Grand Touring 4DR MAZDA3s Sport 5DR MAZDA3s Touring 5DR MAZDA3s Grand Touring 5DR MAZDASPEED3 Sport 5DR MAZDASPEED3 Grand Touring 5DR Page(s) Product Changes 2 Product Summary 3 Equipment & Features 4-6 Packages & Options 7 Accessories 8 .

BMW 5 Series Touring 5dr Estate RR 2004 2010 (E61) MB-SUPRA230550 BMW 6 Series 4dr Saloon NR 1976 1989 (E24) MB-SUPRA01 BMW 7 Series 4dr Saloon FP 1977 1986 (E23) MB-SUPRA01 BMW 7 Series 4dr Saloon FP 1987 1994 (E32) MB-SUPRA02 BMW 7 Series 4dr Saloon FP 1994 2001 (E38) MB-SUPRA02 BMW 7 ser

Civic Coupe (below ) shown in Lunar Silver Metallic with Honda Genuine Accessories. Civic Sedan (top right ) shown in Modern Steel Metallic with Honda Genuine Accessories. BLACK FABRIC CIVIC SEDAN CIVIC COUPE CIVIC Si Powerful. Agile. Versatile enough to handle almost any condition. It's no wonder Honda

Convertible AWD 2013 & Newer 2013 & Newer Bentley Flying Spur 4DR AWD 2018 & Newer 2018 & Newer Bentley Mulsanne 4DR 2013 & Newer 2011 & Newer Bentley Mulsanne Speed 4DR 2017 & Newer 2017 & N

2014 Chevrolet Cruze 2014 Chevrolet Cruze 1PZ69 4dr Sedan 2LT Auto Code Description MSRP 1PZ69 2014 Chevrolet Cruze 4dr Sedan 2LT Auto 22,480.00 SELECTED VEHICLE COLORS Code Description -Interior: JET BLACK/BRICK, MERIDIAN LEATHER-APPOINTED SEAT TRIM -Exterior 1: SILVER ICE METALLIC -Exterior 2: No color has been selected.

organized around five domains: (a) civic beliefs and values, (b) civic behaviors, (c) civic skills, (d) civic socialization, and (e) character strengths. Sample Description. In Wave 1, we recruited 2,467 youth ages 9–18 ( M 13.2) enrolled in Grades 4–12 from 16 schools in three so

R eady. Set. Civic. The Civic keeps getting better. Since 1998, the Civic has been Canada’s best-selling car and it’s no wonder. The exterior and impressive performance of the 2021 Civic solidify its exciting evolution. The sport-inspired d

American Revolution Wax Museum Project Overview You will become an expert on one historical figure who played a significant role in the American Revolution. For this individual, you complete the following tasks: 1. Notes: Use at least 3 sources to research and take notes about the individualʼs life, views, and impact. At least one of