Solid Core 520P / 530P - Particleboard Core (PC) 5 & 7 Ply
Solid Core 520P / 530P - Particleboard core (PC) 5 & 7-PlyHardwood Veneer / MDO / HDFHigh Pressure Decorative Laminate—HPDLWDMA: PC-7 / AWS: PC-7WDMA: PC-HPDL-3/5 / AWS: PC-5 PC-HPDL-3/5Top and Bottom Horizontal Edge: 1-1/8” minimumsolid wood or structural composite lumber, one piece,laminated or LVL.Vertical Edge: 1-1/2” minimum hardwood; solid,laminated veneered. Backer or inner ply may be structural composite lumber or LVL.Core: Particle board, ANSI A208, 1, grade LD-1 orLD-2.Core/Edge Interface: Stiles and rails high frequencybonded to core and core assembly sanded prior toapplication of cross band and veneer.Crossband: 2 ply edge glued hardwood or one pieceHDF. (2-ply shown)Faces: Selected hardwoods minimum 1/50”, Grades“A” , “AA” and high pressure laminate, medium density overlay or hardboard. High pressure laminate0.050” direct to core, 0.050” with cross band or0.125”.Warranty: Lifetime for interior use / one year exterior, fully type 1 wood or MDO faces only.Blocking Options:5” (or as specified) top and/or bottom rail(s). For undercutting and specialized hardware. Must be specified if required.Available Options for 520PFire RatingsThicknesses of 1-3/8” to 2-1/4”. Fire rating to 20 minute - Neutral & Positive Pressure, See Page 4 & 9 for requirements and options.STC rating 32 (Flush & Glazed). May require additional gasketing / seals.LEED Credits, See page 11.Carb 1 & 2 compliant components.Lead lined or electro shielding. (See page 5)Vision lite and louver cutouts with matching flush or raised lip stop. Metal Vision panels or louvers supplied upon request. (See page 7)Applied moldings of any configuration,profile and species. (See page 8)Quirks, grooves and inlays. (See page 7)Dutch cut with matching shelf (See page 7).Wicket door (inset to primary door see page 7).2 or 4 panel Bifold units. (See page 6)Page 3Vancouver Door Company, Puyallup WA.1-800-999-3667www.vancouverdoorco.com
Fire Rated Mineral Core Doors, 745, 760 & 790.FIRE DOORS 760 & 790FIRE DOOR 745Mineral Core 45, Minute Rated, See page 9Mineral Core, 60 & 90 Minute Rated, See page 10.WDMA: FD-7 FD-5WDMA: FD-HPDLWDMA: FD-7 FD-5WDMA: FD-HPDLAWS: FD-7 FD-5AWS:FD-HPDL-5Top and Bottom Horizontal Edge: 1” GP FirestopI See Positive Pressure compliance for all ratings atbottom of page.Top and Bottom Horizontal edge: 1-1/2” GP Firestop II I. See Positive Prressure compliance for allratings at bottom of page.Vertical Edge: GP Fire stop 1 or II with laminatedhardwood. See note 1 at bottom of this page.Additional material may be required.Vertical Edge: GP Fire stop II I with laminatedhardwood. See note 1 and bottom of this page.Additional material may be required.Core: Georgia Pacific (proprietary) Mineral core .Core: Georgia Pacific (proprietary) Mineral core .Core/Edge Interface: Stiles and rails high frequency bonded to core and core assembly sandedprior to application of crossband and veneer.Core/Edge Interface: Stiles and rails high frequencybonded to core and core assembly sanded prior toapplication of crossband and veneer.Crossband: 2 ply edge glued hardwood or Onepiece HDF (One piece HDF shown)Crossband: 2 ply edge glued hardwood or Onepiece HDF (One piece HDF shown)Faces: Selected hardwoods minimum 1/50”, highpressure laminate, medium density overlay or hardboard. High pressure laminate 0.050” with crossband or 0.125”.Faces: Selected hardwoods minimum 1/50”, highpressure laminate, medium density overlay or hardboard. High pressure laminate 0.050” with crossband.Warranty: Lifetime for interior use only.Available Options for 745, 760 & 790 AWS: FD-7 FD-5AWS:FD-HPDL-5Thickness, 1-3/4 only.STC rating of 35. May require additionalgasketing / seals.L.E.E.D. credits (See page 11)Vision lites, Metal kits supplied upon request. All glazing must comply with testapprovals. Ask our tech department.Applied moldings. Limited to rating requirements and area limitations.Warranty: Lifetime for interior use only.Note 1: Any technological advancement madeby Georgia Pacific Corp. in Fire Stop I or IIis automatically included.TECHNICAL DATA 745, 760, 790Slam CycleOver 1,000,000Screw Holding1030.4 lbs.Split Resistance847.9 lbs. average.Blocking (Reinforcement) Options:5” (or as specified) for undercutting and specialized hardware. Specify by number and dimension desired.5” TR5” BRHB-1HB-25”x18”Blkg5” Blkg5”x10”BlkgHB-4HB-6HB-8POSITIVE PRESSURE AND “S” LABEL COMPLIANCE ALL RATINGSCategory A and B, Doors and Jambs from the following options; Georgia Pacific FIREDOOR Components / ZERO International / PEMKOManufacturing / Vancouver Door Company Inc. Testing.INTUMESCENT FREE DESIGN ON 20 / 45 / 60 AND 90 MINUTE DOORS ***Any testing advancement by these companies will automatically be available to customers of Vancouver Door Company Inc. Contact ourfactory for updates on these systems.20 Minute/45, 60, & 90 Minute approval to UBC FireTest Standard 7-2, 1997Smoke and Draft Control Door AssembliesUBC 7-2 (1997) Section 7.210Now available 20 Minute Positive Pressure to 4’x9’ single and 8’x9’ Approval for supplemental “S” label. 20, 45, 60 and 90 MinuteRegular and double egress pairs. Series tested was 520P with 11/2” total hardwood laminated stiles.20 Minute (metal frame) to 4’x9’ singles and 8x9’ regular and double egress pairs. (Wood Frames) to 3’x9’singles and 6’x9’ regular pairs. 45, 60, and 90 MinuteMineral Core Fire Doors to 4’x8’ singles and 8’x8’ regular and double egress pairs. Total intumescent andedge sealing system including assemblyinstallation instructions provided by VDC.745, 760 & 790 Mineral CoreFire Doors are available inPositive Pressure to 4’x8’Singles and 8’x8’ regular andDouble egress pairs.Page 4Vancouver Door Company, Puyallup WA.1-800-999-3667www.vancouverdoorco.com
Specialty Doors, Acoustical, X-Ray, Electro Shielding andBullet Resistant.ACOUSTICAL DOORS (STC) 800LEAD LINED (X-RAY DOORS) 600XRSpecial Acoustical CoreVeneer and High Pressure LaminateAlso Available 20 Minute Rated, See, page 9.Particle Core, Stave Lumber Core, StructuralAcoustical Rating STC 37WDMA: SRWDMA: LLAWS: SRTop and Bottom Horizontal edge: 1-1/2” toprail and 2-3/4” bottom rail minimum solid wood,structural composite lumber or LVL.AWS: LLTop and Bottom Horizontal edge: 1-1/4” solidwood or structural composite lumber, one piece orlaminated.Vertical Edge: 1-1/2” minimum hardwood;solid, laminated or veneered. Backer or inner plymay be structural composite lumber or LVL.Vertical Edge: 1-1/2” minimum hardwood;solid, laminated or veneered. Backer or inner plymay be structural composite lumber or LVL.Core: Acoustical material.Core: Particleboard, ANSI A208,1, grade LD-1 orLD-2. Optional Stave core or SCLC also available.Crossband: 2 ply edge glued hardwood or onepiece HDF. (2-ply shown)Lead: Lead shielding is edge to edge under bothfaces.Core/Edge Interface: Stiles and rails high frequency bonded to core and core assembly sandedprior to application of lead, crossband and veneer.Faces: Selected hardwoods minimum 1/50”, highpressure laminate or medium density overlay.High pressure laminate 0.050” with cross band or0.0125”.Crossband: Edge glued or one piece crossband.Faces: Selected hardwoods minimum 1/50”, highpressure laminate, medium density overlay or hardboard. High pressure laminate 0.050” with crossband or 0.125”.Warranty: Five year warranty for interior use /one year exterior, fully Type 1 only, wood orMDO faces only.Warranty: Lifetime for interior use.Electro Shielding doors are constructed similar to X-RayACOUSTICAL RATINGS - ASTM E90 - 97 & 99Lead ThicknessLbs. per sq. ft.STC RATINGTHICKMAX LIGHTOPENINGFIRERATING321-3/4N/A20 MIN.351-3/4N/A45,60 & 90 MIN.361-3/4N/ABULLET RESISTANT 650371-3/4N/AAcoustical rating STC 37Multiple ply ballistic fiberglass core371-3/4FULL LIGHT371-3/4 lead linedN/A391-3/424X30401-3/424X24 10X36421-3/4N/A431-3/4N/A1/16”1/8”1/4”4 (Typical)816UL 752 -Level 3 Thru 520 MIN.Top and Bottom Horizontal edge: 1” solid hardwood .Vertical Edge: 3/4” minimum solid hardwoodand or structural composite lumber or LVL.Core/Edge Interface: Stiles and rails high frequency bonded to core assembly then sanded priorto application of crossband and veneer.STC TEST RESULTS AVAILABLE BY REQUEST.Available Options for 800, 600 & 650.Many of the same options listed for the “Solid Core” products also applyto the products listed on this page.Faces: Selected hardwoods minimum 1/50”, highpressure laminate, medium density overlay or hardboard. High pressure laminate 0.050” with crossband or 0.125”.Check with our sales or technical departments.Warranty: Lifetime for interior use only.Page 5Vancouver Door Company, Puyallup WA.1-800-999-3667www.vancouverdoorco.com
Hollow Core, Bifolds and SlidersSTANDARD HOLLOW CORE 310INSTITUTIONAL HOLLOW CORE 510Honeycomb Core.Honeycomb Core.2 lock blocks & Intermediate rail included.WDMA: IHC-7AWS: IHC-7WDMA: IHC-HPDLWDMA: SHC-7WDMA: SHC-HPDLAWS: SHC-7Top and Bottom Horizontal edge: 1-1/8”minimum solid wood, medium density fiberboard orstructural composite lumber, one piece or laminated.Top and Bottom Horizontal edge: 6-1/2” solidwood, medium density fiberboard or structuralcomposite lumber, one piece or laminated.Vertical Edge: 1” minimum solid, laminated orveneered wood. Backer or inner ply may be structural composite lumber or LVL.Vertical Edge: 2-1/2” minimum solid, laminated orveneered wood. Backer or inner ply may be structuralcomposite lumber.Core: Honeycomb fully expanded to edges.Core: Honeycomb fully expanded to all edges.Bonding: Vertical edges and rails not bonded tocore.Bonding: Vertical edges and rails not bonded tocore.Crossband: Edge glued or one piece cross band.Crossband: Edge glued or one piece crossband.Faces: Selected hardwoods minimum 1/50”,Faces: Selected hardwoods minimum 1/50”,high pressure laminate, medium density overlayor hardboard. High pressure laminate 0.050” withcrossband or 0.125”.High Pressure Decorative Laminate (HPDL)NOT provided on Hollow Core doors.Warranty: One year for interior use. 0nly!Warranty: One year for interior use only.BIFOLD (FOLDING) UNITS, 2 & 4 DOORSLIDERS, POCKET DOORS & PANELSHollow Core & Solid Core. (Non rated)Veneer, HDF, MDO and High Pressure Laminate.1-3/8” - 1-3/4” thicknesses.Hollow Core & Solid Core. (Non rated)Matching Veneer, HDF, MDO and High Pressure Laminate.1-3/8” - 1-3/4” thicknesses.Heavy Duty hardware supplied upon request.Blocking (Reinforcement) Options:Specify by number and dimension desired.5” TR5” BRHB-1HB-35”x18”BlkgHB-45” BlkgHB-55”x5”HookBlockHB-7Available Options: 2 & 4 Door Bifold unitPage 6LEED Credits (Solid core doors only).Vision lite and Louver cut outs.Quirks, grooves and inlays.Hardware preparation.Warranty: Lifetime Interior use onlyVancouver Door Company, Puyallup WA.1-800-999-36672 & 4 Door sliders.www.vancouverdoorco.com
Special Services and Products.Vancouver Door Company’s many custom services reduce job site costs and assist in meeting time requirements on special installations.WICKET DOORSDOORS w/ VISION LITESWicket doors are utilized in applicationswhere only a portion of the door openingneeds to be accessible. They consist ofthe primary door and the wicket insertwhich can be opened to allow accesswhile keeping the primary door closed /locked.Vision lites can be provided in many different configurations and sizes. We canprovide stop and glass. Factory glazing isavailable as well.Faces are matched so that the wicketdoor matches the face on the primarydoor.Check with our sales or tech departmentAvailable non-rated and 20, 45, 60, and90 minute rated. See pages 9 & 10.Standard bead stopWicket doors are attached with continuous or concealed hinges and can belatched with standard lock prep.Not approved for fire rated applications.Not approved for STC rated applications.DOORS & TRANSOMSLOUVER DOORSVeneers may be continuous match, endmatch or no match. (End matchedshown)Variable size and type louvers can beprovided and installed at the factory. Fromsmall to half to full size louvers.See WDMA: I.S. 1-A, Section A-6Great for providing pass throughVentilation and fresh air.Rabetted meeting rails are optional.Chevron style louvers are available inmost hardwoods.Not approved for STC applications.Available non-rated and 20, 45, 60, and90 minute rated. See pages 9 & 10.Available non-rated and 45, 60, and 90minute rated. See pages 9 &10.Check with our sales or tech departmentfor details & options.Not approved for 20 minute!INLAYS, QUIRKS, APPLIED MOLDING.DUTCH DOORSDutch doors are utilized in applicationswhere the upper half of the door may beopened while keeping the lower halfclosed. Both leaves are typically latchedtogether to maintain a single opening.Inlays, Quirks (grooves), Applied moldingcan be provided in many different configurations and sizes based on your specifications.Typical molding profilesDutch door shelves on one side only or onboth sides of the door.All shelves are sent loose for field installation.Available non-rated and 20, 45 or 60minute rated. See pages 9 & 10.Check with our sales or tech departmentfor details & optionsPage 7Vancouver Door Company, Puyallup WA.Available non-rated and 20, 45, 60, and90 minute rated. See pages 9 & 10.1-800-999-3667www.vancouverdoorco.com
Special Services—continuedSKETCH FACEVarious configurations based on any given design and veneer species.EDGE OPTIONSPrefitting and edge beveling.Radius edges.Edge rabbeting.Veneered or plastic laminate edges to match faces.FACTORY MACHININGDoors can be prepared for any standard or custom hardware.Precision factory machining and pre-fitting ensure proper hardwarepreparation for tolerances specified by National Fire ProtectionAssociation (NFPA), the Architectural Woodwork Standards (AWS),the Window and Door Manufacturers Association (WDMA) and theDoor and Hardware Institute (DHI).STILE and RAILWood doors in various species, sizes, configurations and fire ratings.Concealed overhead closer w/fire shield for rated doorsFACTORY PREFINISHINGThe controlled application process in factory prefinishing assures topquality finishes with maximum durability not possible with site appliedcoatings. See WDMA I.S. 1-A, Section F-1 through F-7.Some of our machining options include: Concealed Vertical Rods (Less Bottom Rod—LBR) Raceway’s (Wire-chases)Concealed hinges, Anchor hinges, Pivot hinges.Mortised door bottomsMortised edge guardsOur expert staff can coordinate your projects to ensure a smoothinstallation of hardware to doors.WOOD JAMBSWood and wood veneered jambs in many species side light jambsare also available.Available non-rated, 20 to 90 minute rated.Positive Pressure “S” label available in 20 to 90 minute singlesand pairs.20 minute rated wood jambs in sizes up to 4’x9’ singles and 8’x9’pairs.PARTITIONS, WALL PANELS & DESK TOPS.Provided in any specie veneer and plastic laminate.Sizes up to 4’x10’ in 1” to 1-3/4” thick with edge banding to match oras specified.PRESERVATIVE / INSECT TREATMENTAvailable on request.Page 8Vancouver Door Company, Puyallup WA.1-800-999-3667www.vancouverdoorco.com
Fire Rated Doors - Single Swing and Pairs20 MinuteRatings45 MinuteSwing Door Pair Regularand tranor DoublesomEgressLead LinedSingle SwingSingle Swing,Door and TransomPair Regular orDouble EgressYes*Yes*Yes*Yes*Yes*4’x10’ Single4’x10’ DR/TRMax TR 4’x2Or 3’x3’Up o 8’x9’6’x10’8’x9’ DE4’x9’4’x10’3’x10’ DR/TRMax TR 3’x3’6’x7’ Note: 68’x8’ Reg/DE8’x9’ CVREProtection Plates48”x48”48”x48”48”x48”48”x48” Note: 248”x48” Note: 2EPTYesYesYesYes Note: 2Yes Note: 2Wire ChaseYesYesYesYesYesDutch Door4’x8’No Vision PanelN/AN/A4’x8’No Vision PanelN/AMaximum VisionPanel1,296 sq. in.36” Wide54” High1,296 sq. in.36” Wide54” HighN/A1,296 sq. in.2,638 sq. in. Note: 11,296 sq. in.2,638 sq. in. Note: 1Maximum LouverFusible LinkN/AN/AN/A24”x24”24”X24’ each leafViewersUp to 1” diameterUp to 1” diameterN/AUp to 1” diameterUp to 1” diameterHingesPer NFPA #80Per NFPA #80Per NFPA #80Per NFPA #80Note: 7Per NFPA #80Note: 7LocksCylindrical / unit /mortiseCylindrical / unit /mortiseCylindrical / unit /mortiseCylindrical / unit / mortiseCylindrical / unit / mortiseExit DevicesListed rim, mortise Listed rim, mortise or Listed rim, mortiseor vertical rodvertical rodor vertical rodListed rim, mortise orvertical rodListed rim, mortise orvertical rodPositive Pressure“5” LabelSizesFlush BoltsTop/Bottomfor Inactive LeafsN/AEdge GuardsYes Note: 3Yes Note: 3Yes Note: 3Yes Note: 3Yes Note: 3ConcealedVertical RodYesYes, no channelrequiredN/AYes, 5”channel may berequiredYes, 5” channel may berequiredConcealed Closers YesYesN/AYes Note: 2Yes Note: 2Applied MoldingsYesYesNoYesYesAutomatic DoorBottomsYesYesN/AYes Note: 2Yes note: 2Note: (1)(2)(3)(4)Listed surface manualor automatic flushN/Abolts installed with 28gauge linerSpecial glass and stop required/max size 36”x80”.Special blocking required.Special edges required.Special glass and stop required.Listed surface manual orautomatic flush boltsinstalled with 28 gaugelinerN/A(5) Special blocking required.(6) No astragal required with special blocking.(7) Special hinges and pivots require additional blocking.*Contact factory for maximum sizes and options for Neutral and Positive Pressure requirements.Page 9Vancouver Door Company, Puyallup WA.1-800-999-3667www.vancouverdoorco.com
Fire Rated Doors - Single Swing and Pairs60 MinuteRatings90 MinuteSingle Swing,Door andTransomPair Regular orDouble EgressSingle Swing, Doorand TransomPair Regular or Double EgressYes*Yes*Yes*Yes*4’x10’3’x10’ DR/TRMax TR 3’x3’6’x7’ Note: 68’x8’ Regular/DE8’x9’ CVRE4’x10’3’x10’ DR/TRMax TR 3’x3’6’x7’ Note: 68’x8’ Regular/DE Note: 88’x9’ CVREProtection Plates48”x48” Note: 5page 948”x48” Note: 5 page 948”x48” Note: 5 page 948”x48” Note: 5 page 9EPTYes Note: 2 page 9Yes Note: 2 page 9Yes Note: 2 page 9Yes Note: 2 page 9Wire ChaseYesYesYesYesDutch Door4’x8”No Vision PanelN/AN/AN/AMaximum VisionPanel100 sq. in.1015 sq. in. Note: 4page 9100 sq. in.1015 sq. in. Note: 4page 9100 sq. in.1015 sq. in. Note: 4 page 9100 sq. in.1015 sq. in. Note: 4 page 9Maximum LouverFusible Link24”x24”24”x24” each leaf24”x24”24”x24” each leafViewersUp to 1” diameterUp to 1” diameterUp to 1” diameterUp to 1” diameterHingesPer NFPA #80 Note: Per NFPA #80 Note: 77 page 9page 9Per NFPA #80 Note: 7 page 9Per NFPA #80 Note: 7 page 9LocksCylindrical / unit /mortiseCylindrical / unit / mortiseCylindrical / unit / mortiseCylindrical / unit / mortiseExit DevicesListed rim, mortise orvertical rodListed rim, mortise orvertical rodListed rim, mortise or verticalrodListed rim, mortise or verticalrodFlush BoltsTop/Bottomfor Inactive LeafsN/AListed surface manual orautomatic flush boltsN/AListed surface manual orautomatic flush bolts installedEdge GuardsYes Note: 3, page 9Yes Note: 3 page 9Yes Note: 3 page 9Yes Note: 3 page 9ConcealedVertical RodYes, 5” channel maybe required.Yes, 5” channel may berequiredYes, 5” channel may berequiredYes, 5” channel may berequiredConcealed ClosersYes Note: 2 page 9Yes Note: 2 page 9Yes Note: 2 page 9Yes Note: 2 page 9Applied MoldingsYesYesYesYesAutomatic Door BottomsYes Note: 2 page 9Yes Note: 2 page 9Yes Note: 2 page 9Yes Note: 2 page 9Positive Pressure “5”LabelSizesTesting: Labeled fire doors have been tested in accordancewith UL 10(B), CAN 4S 104(ULC-S104), NFPA 252 and UBC7-2 fire door test standards.Page 10Labeling: Testing, inspection and labeling is by Intertek Testing Services/Warnock Hersey, Inc. Vancouver Door Co. is listed to manufacture and machine fire rated wood doors. Labels are affixed to hingeedge at eye level, or on top rail if positive pressure.Vancouver Door Company, Puyallup WA.1-800-999-3667www.vancouverdoorco.com
Matrix for LEED Credit ContributionsDeveloped by the U/S Green Building Council (USGBC), Leadership in Energy and Environmental Design (LEED)provides building owners and operators a concise framework for identifying and implementing practical and measurable green building design, construction, operations and maintenance solutions.The matrix below identifies the wood doors (Veneered and laminated faces) that qualify for credits for a specificproject. All LEED projects must be specified when submitting a quote request or a purchase order to ensure thatyou obtain the necessary contributions from the doors. Please feel free to contact us with any questions or if youneed additional information. 1-800-999-3667All Vancouver Door products are in compliance with California Air Resource Board (CARB) Phase 2 requirements.Product Type(Wood & HPDL Faces)MR 4.1MR 4.2MR 5.1MR 5.2MR 6MR 7EQ 4.4310 - Hollow Core (HC)YesYesNoNoNoNoNo510 - Institutional Hollow Core (IHC)YesYesNoNoNoNoNo520P - Particle Core (PC)YesYesNoNoNoYesYes520A - Agrifiber Core (AC)NoNoNoNoYesYesYes520S - (SLC)NoNoNoNoNoYesYes520C - (SCLC)YesYesNoNoNoNoYes600P - Lead Lined (LLPC)YesYesNoNoNoYesYes600S - Lead Lined (LLSLC)NoNoNoNoNoYesYes600C - Lead Lined (LLSCLC)YesYesNoNoNoNoYes650P - Bullet Core (BCPC)YesYesNoNoNoYesYes745M - Mineral Core (MC45)YesYesNoNoNoYesYes760M - Mineral Core (MC60)YesYesNoNoNoYesYes790M - Mineral Core (MC90)YesYesNoNoNoYesYes836 - Sound Transmission Class (STC36)YesYesNoNoNoYesYes839 - Sound Transmission Class (STC39)YesYesNoNoNoYesYes840 - Sound Transmission Class (STC40)YesYesNoNoNoNoNo841 - Sound Transmission Class (STC42)YesYesNoNoNoNoNo843 - Sound Transmission Class (STC43)YesYesNoNoNoNoNoMR 4.1 Recycled Content: 10% (Post Consumer 1/2 PrePre-Consumer)MR 4.2 Recycled Content: 20% (Post Consumer 1/2 PrePre-Consumer)MR 5.1:Regional Materials: 10% Extracted, Processed & Manufactured RegionallyMR 5.2 Regional Materials: 20% Extracted, Processed & Manufactured RegionallyMR 6: Rapidly Renewable MaterialsMR7: Certified WoodEQ 4.4: LowLow-Emitting Materials - No Added Urea Formaldehyde (NAUF)Page 11Vancouver Door Company, Puyallup WA.1-800-999-3667www.vancouverdoorco.com
Pan Pacific Hotel SeattleLourdes HospitalZebrawoodFort Harrison Hotel Clearwater, FLPanorama Towers, LV, NevadaVancouver Door Company, Puyallup WA.1-800-999-3667www.vancouverdoorco.com
Core: Particleboard, ANSI A208,1, grade LD-1 or LD-2. Optional Stave core or SCLC also available. Core/Edge Interface: Stiles and rails high fre-quency bonded to core and core assembly sanded prior to application of lead, crossband and veneer. Lead: Lead shielding is edge to edge under
4 4 Standard Particleboard Standard Particleboard is the standard, basic type of Particleboard product. It is not suitable for exterior use, or in interior areas where wetting or prolonged high humidity conditions are likely.
a precision balance (Adventurer SL AS313; Ohaus Corp., USA) to ascertain the optimum particleboard drying time. Fig. 3 shows the relation between mass change and drying time. This result demonstrates that the mass change is slight after 8 h drying time. Then the particleboard was dried in a
National Standard, ANSI A208.1 for mat-formed wood particleboard. Developed under the auspices of the American National Standards Institute, ANSI A208.1 is a voluntary product standard, which means that producers are not restricted to the manufacture of particleboards conforming to the standard. Conformance to the standard is required only when .Cited by: 14Publish Year: 1986Author: C. G. CarllExplore furtherAP-42 CH 10.6.2 Particleboard Manufacturingwww3.epa.govParticle board Wood Productswww.woodproducts.fiArchitectural Woodwork Standards SHEET PRODUCTS 4woodworkinstitute.comParticle board - Wikipediaen.wikipedia.orgRecommended to you b
mat, hot pressing, and finishing. Figure 10.6.2-1 presents a process flow diagram for a typical particleboard plant. The furnish or raw material for particleboard normally consists of wood particles, primarily wood chips, sawdust, and planer shavings. This material may be shipped to the facility or generated onsite and stored until needed.
A208.1 was developed through the sponsorship of the Composite Panel Association (CPA) in conjunction with producers, users and general interest groups. A summary of the Particleboard Property Requirements is included in this Guide and copie
All particleboard components will meet ANSI A208.1 for formaldehyde emission limits, or all exposed particleboard edges will be sealed with a low-VOC sealant or have a factory-applied, low-VOC sealant prior to installation. All MDF edges will meet ANSI A208.2 for formaldehyde emissi
The following information provides a guide to the applications, properties and features of the full product range. It also details the appropriate installation systems for STRUCTAfl or and TERMIfl or. Note: Particleboard fl ooring is not to be used in weather exposed applications or with under-carpet heating. Particleboard Flooring
MBA Artificial Intelligence . Academic Level . 7. Total Credits . 180. Professional Body Accreditation not applicable/ Qualification Date of Professional Body Accreditation . not applicable . Accreditation Period : not applicable : UCAS Code : not applicable: HECoS Code : 100079: Criteria for Admission to the Programme : We welcome applications from students who may not meet the formal entry c
