Fisher ET, EAT, And ETR Sliding Stem Control Valves
Product BulletinET Valve51.1:ETOctober 2020D100022X012Fisher ET, EAT, and ETR Sliding-StemControl ValvesFisher ET, EAT, and ETR general-purpose control valves(figures 1, 2, and 3) are used for throttling or on-offcontrol of a wide variety of liquids and gases. All threevalve designs have single ports, balanced valve plugs,and cage guiding. Metal-to-PTFE seating for stringentshutoff requirements is standard in all valves exceptthose with Cavitrolt III cages. Metal-to-metal seatingfor higher temperatures is standard for valves withCavitrol III cages and optional for all other valves.The temperature limits of ET valves can be extendedabove 232 C (450 F) by using PEEK(PolyEtherEtherKetone) anti-extrusion rings incombination with a spring-loaded PTFE seal. The PEEKanti-extrusion rings expand to close off the clearancegap between the plug and the cage where the PTFEseal may extrude at high temperatures and pressures.The temperature limits are extended to 316 C (600 F)for non-oxidizing service and to 260 C (500 F) foroxidizing service.The ET product line is available for a wide range ofapplications, including sulfide and chloridestress-cracking environments common to the oil andgas production industries. To discuss availableconstructions, contact your Emerson sales office andinclude the applicable codes and standards requiredfor these environments.W1916-4FISHER ET CONTROL VALVEWITH 667 ACTUATORnDifferent cage/plug styles that provide particularflow characteristics for highly-specializedapplications. The standard cage comes in threedifferent flow characteristics: quick-opening, linear,or equal percentage.nWhisper Trimt I, Whisper Trim III (figure 6), andWhisperFlot cages (figures 4 and 5) attenuateaerodynamic noise in gaseous service.nTo help eliminate cavitation damage in aproperly-sized valve, a standard-travel, Cavitrol III,one-stage cage (figure 8) and a long-travel, CavitrolIII, two-stage cage are available in the NPS 1through NPS 8 ET control valve.The easy-e Valve FamilyET, EAT, and ETR control valves are part of the versatileeasy-e family of Fisher industrial control valves. easy-evalves share the following characteristics:nMultiple trim material choicesnInterchangeable, restricted-capacity trims andfull-sized trims to match variable process flowdemandswww.Fisher.com
Product BulletinET Valve51.1:ETOctober 2020D100022X012FeaturesnCompliance with the Clean Air Act— ENVIRO-SEAL packing systems (figures 9 and 10) that provide animproved stem seal to help prevent the loss ofprocess fluid are available. These packing systemsfeature PTFE or Graphite ULF packing withlive-loading for reduced packing maintenance.nPTFE Seating for Long-Lasting ShutoffCapability—Controlled compression of standardseat construction protects PTFE disk between metaldisk seat and disk retainer (figure 1). Only the edgeof the PTFE disk is contacted by the flowstreamduring normal operation. Excellent shutoff ismaintained by a backup ring or spring-loading thatforces the valve plug seal ring against the cage(figure 1).nValve Plug Stability— Rugged cage guiding provideshigh valve plug stability, which reduces vibrationand mechanical noise.nCost-Effective Operation and MaintenanceEconomy—Increased wear resistance of hardenedstainless steel trim means longer-lasting service.When inspection or maintenance is necessary, thebody can stay in the pipeline during removal of trimparts. Balanced valve plug construction permits useof smaller, lower-cost Fisher actuators. The ETRvalve also permits easy body interior access withouthaving to remove the bonnet or actuator (figure 3).And, trim inventory costs are cut becausedimensional standardization permits use of moststandard easy-e trim parts.nCompliance with European Standards— Valves areavailable with dimensions specified by EN/DINstandards. See figure 14.nSour Service Capability— Unless otherwise noted,references are to NACE MR0175-2002. Optionalmaterials are available to meet NACE MR0103 andNACE MR0175 / ISO 15156. Material requirementsunder these standards vary by edition and year ofissue; the specific standard must be specified.Table of ContentsFeatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ENVIRO-SEAL Packing SystemSpecifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ENVIRO-SEAL and HIGH-SEALPacking Systems . . . . . . . . . . . . . . . . . . . . . . . . . . .ANSI/FCI Class VI ShutoffCapabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TablesAvailable Constructions . . . . . . . . . . . . . . . . . . . . . . .Shutoff Classifications . . . . . . . . . . . . . . . . . . . . . . . .Class VI Shutoff Availability . . . . . . . . . . . . . . . . . . . .Class VI Trim Materials . . . . . . . . . . . . . . . . . . . . . . . .2234665566Trim Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Materials and Temperature Limits forOther Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Valve Body/Trim TemperatureCapabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Bonnet Selection Guidelines . . . . . . . . . . . . . . . . . .Maximum Flow Coefficients . . . . . . . . . . . . . . . . . .Port Diameters, Valve Plug Travel,Stem and Yoke Boss Diameters . . . . . . . . . . . . .Metal Trim Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . .Bolting Materials and Temperature Limits . . . . . .Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . .10171920202124242528
Product BulletinET Valve51.1:ETOctober 2020D100022X012Specifications(cast 316 stainless steel), J CF3M (cast 316Lstainless steel) or J other materials upon requestValve Plug, Cage, and Metal Seating Parts:All Valves Except Those with Cavitrol III or Whisper TrimIII Cages: See table 5Valves with Cavitrol III Cages: See table 6Valves with Whisper Trim III Cages: See table 8Valves with WhisperFlo Cages: See table 7Bellows Seal Assembly: J 316L stainless steel orJ N04400All Other Parts: See table 9Available ConfigurationsET: Single-port, globe-style control valve with cageguiding, balanced valve plug, and push-down-to-closevalve plug action (figure 1)EAT: Angle version of ET control valve, used tofacilitate piping or in applications where aself-draining valve is desired (figure 2)ETR: Same as ET control valve except withpush-down-to-open valve plug action (figure 3)Valve Sizes and End Connection StylesFlanged raised-face per EN 1092-1/B and see table 1Material Temperature Capabilities(2)Body/Trim Combinations:All Valves Except Those with Cavitrol III or Whisper TrimIII Cages: See figure 11Valves with Cavitrol III Cages: See table 6Valves with Whisper Trim III Cages: See table 8Valves with WhisperFlo Cages: See table 7Bolting For NACE MR0175 / ISO 15156 and MR0103:See table 19Bonnets: See table 11All Other Parts: See table 9Maximum Inlet Pressures and Temperatures(1,2)As listed below, unless limited by maximum pressuredrop or material temperature capabilitiesValves with Cast Iron BodiesFlanged: Consistent with CL125B or 250B per ASMEB16.1Valves with Steel and Stainless Steel BodiesFlanged: Consistent with CL150, 300, and 600(3) perASME B16.34Screwed or Welding: Consistent with flanged CL600per ASME B16.34Flow CharacteristicsStandard Cages: J Quick-opening, J linear, orJ equal percentageWhisper Trim, WhisperFlo, and Cavitrol Cages: LinearMaximum Pressure Drops(2)Same as maximum inlet pressure for specificconstruction defined above, except where furtherlimited as follows:All Valves Except Those with Cavitrol III, Whisper TrimIII, and WhisperFlo Cages: See figure 11.Valves with Cavitrol III Cages: See figure 12.Valves with Whisper Trim III Cages: 0.999 ΔP/P1maximum for levels A1 through D3Valves for NACE MR0175 / ISO 15156 and MR0103:See figure 13Flow DirectionsETStandard Cage: Normally downWhisper Trim and WhisperFlo Cages: Always upCavitrol Cage: Always downEATStandard Cage with Liner for Metal Seat: NormallydownStandard Cage without Liner: Flow up or downWhisper Trim and WhisperFlo Cages: Always upETRStandard Cage: Normally upWhisper Trim Cage: Always downShutoff Classifications Per ANSI/FCI 70-2and IEC 60534-4Class IV, V, or VI. See tables 2, 3, or 4Construction MaterialsBody, Bonnet, and Bonnet Spacer or Bottom Flange, ifused: J Cast iron, J WCC carbon steel, or J LCCcarbon steel, J WC9 chrome moly steel, J CF8MFlow Coefficients and Noise Level PredictionSee table 12 and Catalog 12- continued -3
Product BulletinET Valve51.1:ETOctober 2020D100022X012Specifications (continued)Port Diameters and Maximum Valve Plug TravelsSee tables 13, 15, and 16Yoke Boss and Stem DiametersSee table 14Typical Bonnet StylesSee table 11Packing ArrangementsStandard Material: Single PTFE V-ringOptional Materials: See table 9ENVIRO-SEAL Packing Systems: See figures 9 and 10ENVIRO-SEAL Packing Systems in vacuum service:Standard ENVIRO-SEAL packing systems can be usedin vacuum service with packing rings in standardorientation. Do not reverse the ENVIRO-SEAL PTFEpacking rings. Also, see Bulletin 59.1:061,ENVIRO-SEAL Packing Systems for Sliding-StemValves (D101633X012).Approximate WeightsNPS 1: 14 kg (30 lb)NPS 1-1/2: 20 kg (45 lb)NPS 2: 39 kg (85 lb)NPS 2-1/2: 45 kg (100 lb)NPS 3: 57 kg (125 lb)NPS 4: 77 kg (170 lb)NPS 6: 159 kg (350 lb)NPS 8: 408 kg (900 lb)Optional Safety Instrumented System ClassificationSIL3 capable — certified by exida Consulting LLCAdditional OptionsJ Lubricator, J lubricator/isolating valve, J drilledand tapped connection in extension bonnet forleak-off service, J body drain plug, J style 3fabricated extension bonnet made on order to aspecific length for cryogenic service, J style NSbonnet for seismic service requirements, J packingssuitable for nuclear service, J Class V shutoff for ETabove 232 C (450 F) using PEEK anti-extrusion rings1. EN (or other) ratings and end connections can usually be supplied; consult your Emerson sales office.2. The pressure or temperature limits in this bulletin, and any applicable code limitations, should not be exceeded.3. Certain bonnet bolting material selections may require a CL600 easy-e valve assembly to be derated. Contact your Emerson Automation Solutions sales office for more information.4. Limitation based on excessive noise increase if max ΔP/P1 ratio for a given cage level is exceeded.ENVIRO-SEAL Packing System SpecificationsApplicable Stem DiametersJ 9.5 mm (3/8 inches), J 12.7 mm (1/2 inches),J 19.1 mm (3/4 inches), J 25.4 mm (1 inch), andJ 31.8 mm (1-1/4 inches) diameter valve stemsMaximum Pressure/Temperature Limits(1)To Meet the EPA Fugitive Emission Standard of 100PPM(2)For ENVIRO-SEAL PTFE and ENVIRO-SEAL Duplex packingsystems: full CL300 up to 232 C (450 F)For ENVIRO-SEAL Graphite ULF packing: 104 bar (1500psig) at 316 C (600 F)Construction MaterialsPTFE Packing SystemsPacking Ring and Lower Wiper: PTFE V-ring(3)Male and Female Adaptor Rings: Carbon-filled PTFEV-ringGraphite ULF Packing Systems: Graphite ringsDuplex Packing Systems:Male and Female Adaptor Rings: Carbon-filled PTFEV-ringGuide Bushings: Carbon graphitePacking Rings: Graphite compositePacking Washer: PTFEAnti-Extrusion Washer: Filled PTFE (not required forGraphite ULF or duplex packing)Lantern Ring: S31600 (316 stainless steel) (notrequired for Graphite ULF packing)Packing Box Flange: S31600Spring: J 17-7PH stainless steel or J N06600Packing Follower: S31600 lined with carbon-filledPTFEPacking Box Studs: Strain-hardened 316 stainlesssteelPacking Box Nuts: 316 stainless steel SA194 Grade8M1. Refer to the valve specifications in this bulletin for pressure/temperature limits of valve parts. Do not exceed the pressure/temperature rating of the valve. Do not exceed any applicable codeor standard limitation.2. The Environmental Protection Agency (EPA) has set a limit of 100 parts per million (ppm) for fugitive emissions from a valve in selected VOC (Volatile Organic Compound) services.3. In vacuum service, it is not necessary to reverse the ENVIRO-SEAL PTFE packing rings.4
Product BulletinET Valve51.1:ETOctober 2020D100022X012Table 1. Available ConstructionsVALVE BODY MATERIAL AND END CONNECTION STYLE(1)VALVEVALVE SIZE,NPSCast Iron Valve BodyCarbon Steel, Alloy Steel, or Stainless Steel Valve BodyCL125FF FlangedCL250RF FlangedScrewedRF or RTJ FlangedCL150CL300CL600ButtWeldSocketWeldET1, 1-1/2, or 22-1/2, 3, 4, 6, or 8XXXXX---XXXXXXXXXXEAT1 or 23, 4, or 6---------------XXXXXXXXXXETR1, 1-1/2, or 22-1/2, 3, or 4----------X---X---X---X---X---X---VALVEVALVE SIZE,DNPN16PN25PN40PN63PN100ET25, 40, 50, 65, 80,100, 150, or 200XXXXXEAT25, 50, 80, 100, or150XXXXXETR25, 40, 50, 65, 80,or 100XXXXXSTEEL VALVE BODY MATERIAL AND RAISED-FACE END CONNECTION STYLE(2)X Available Construction.1. End connection style abbreviations: FF - Flat Faced, RF - Raised Face, RTJ - Ring Type Joint.2. End connection EN1092-1/B.Table 2. Shutoff Classifications Per ANSI/FCI 70-2 and IEC 60534-4Valve DesignSeatingShutoff ClassPTFEV (optional)V Air TestVI (optional)(3)All except those with Cavitrol III cagesIV (standard)MetalV (optional)(1)VI (optional)(3)IV (standard)ET with Cavitrol III one-stage cageMetalET with Cavitrol III two-stage cagesMetalVET and EAT w/ TSO (Tight Shutoff) trim(CL125 through 600)Replaceable,protected soft seatET w/ TSO (Tight Shutoff) trim (CL125through 600)Std or Cavitrol IIItrim. Replaceable,protected soft seat.TSO(2)TSO is not an ANSI/FCI leakage class.Valves with TSO trim are factory tested to a more stringent Emerson AutomationSolutions test requirement of no leakage at time of shipment. Test medium is water.Specify service nP when ordering. Shutoff class V.V (optional)1. Class V shutoff requires spring-loaded seal ring, radius-seat plug, and wide-bevel seat ring (not available with 8-inch port, quick-opening cage). Not available with trims 4, 29, and 85.2. For additional information, contact your Emerson sales office.3. Refer to table 3.5
Product BulletinET Valve51.1:ETOctober 2020D100022X012ENVIRO-SEAL, HIGH-SEALPacking SystemsULF packing system (figure 10) is offered. TheHIGH-SEAL packing system provides improved sealingat pressure/temperature ratings beyond ENVIRO-SEALlimits.ENVIRO-SEAL and HIGH-SEAL packing systems offerexceptional sealing capabilities. These systems easilyinstall in existing valves or can be purchased with newvalves. These systems help seal the process toconserve valuable process fluid. The long-life andreliability of these systems also reduce maintenancecosts and downtime.ENVIRO-SEAL packing systems, available with PTFE,Graphite ULF, or duplex packing, and the HIGH-SEALGraphite ULF packing system feature live-loading andunique packing-ring arrangements for long-term,consistent sealing performance.For applications requiring compliance withenvironmental protection regulations, the uniqueENVIRO-SEAL packing system (figure 10) and a uniqueENVIRO-SEAL bellows seal system (figure 9) areoffered. The emission control packing system keepsemission concentrations below the EPA 100 ppmrequirement.ANSI/FCI Class VI ShutoffCapabilitiesET valves with soft seat and metal seat constructionscan provide ANSI/FCI Class VI shut-off capabilities. Seetables 3 and 4.For an excellent stem seal in applications that are notenvironmentally-sensitive, the HIGH-SEAL GraphiteTable 3. Class VI Shutoff Availability(1, 2)ValvePort Size, InchesSeatET 3.4375 7SoftMinimum Seat LoadSee Catalog 14ET 3.4375 7Metal300 lbs/lineal inch1. Limited retrofit capability. Consult your Emerson sales office.2. Not for use with NPS 8.Table 4. Class VI Trim MaterialsVALVECAGE/SEATRING RETAINERVALVE PLUGSEAT RINGSEAL RING316 SST / ENCS31600 w/standard beveledseatS31600/PTFE316 SST / ENCET17-4 SST(17-4PH SST)S31600/CoCr-Aseat w/radiused seat(special design)S41600 w/standard beveledseat17-4 SST1. UHMWPE (Ultra High Molecular Weight Polyethylene)6S41600 w/radiused seat(special design)TRIM TEMPERATURE LIMITCFUHMWPE(1)R30003-198 to 66-325 to 150S31600 w/ widebeveled seat(special design)UHMWPE R30003-198 to 66-325 to 150S31600/PTFEUHMWPE R30003-29 to 66-20 to 150S31600 w/ widebeveled seat(special design)UHMWPE R30003-29 to 66-20 to 150
Product BulletinET Valve51.1:ETOctober 2020D100022X012Figure 1. Fisher ET Sectional with Standard CagesRETAININGRINGSEAL RINGLOADRINGMETALBACKUPRINGSEAL RINGW7019-1W0995-2W2914-1STANDARD NPS 8CONSTRUCTIONNPS 1 THROUGH 4 ET(ALSO NPS 1 THROUGH 6 EAT)NPS 6 OR 8 ETSPRING-LOADED SEAL RING CONSTRUCTIONFOR USE WITH CAVITROL CAGES AND FORMETAL SEAT WITH OPTIONALCLASS V SHUTOFFPTFE V-RINGPACKINGCAGEGASKETBONNETGASKETBONNET GASKETBACKUP RINGSEAL RINGVALVE MSPIRALWOUNDGASKETW2001-2OPTIONAL RESTRICTED TRIMPINSEAT RINGGASKETMETALDISK SEATW3162-3PTFE DISKMETAL DISKRETAINERSTANDARD NPS 1 THROUGH6 CONSTRUCTIONMETALSEATRINGW0983-2OPTIONAL METAL-TO-METALSEATING7
Product BulletinET Valve51.1:ETOctober 2020D100022X012Figure 2. Fisher EAT SectionalFigure 3. Fisher ETR SectionalW0972-3W1557-4Figure 4. Typical Valve with WhisperFlo Aerodynamic TrimW6980WhisperFlo TRIMW6851-18
Product BulletinET Valve51.1:ETOctober 2020D100022X012Figure 5. Typical WhisperFlo CageW7065W6851-19
Product BulletinET Valve51.1:ETOctober 2020D100022X012Table 5. Typical Combinations of Metal Trim Parts for All Valves Except Those for NACE MR0175 / ISO 15156 andMR0103 Specifications(1), Cavitrol III(2), Whisper Trim III(3), and 4, 6, and 8-Inch WhisperFlo Cages(6)Disk Seat and RetainerforStandardPTFE-SeatConstructionSeat Ring orLiner for OptionalMetal-Seat ConstructionOptional Liner(Metal SeatEAT ValveOnly)---S41600 HT or CA15 HT(4)S41600 HTR30006 orR30016 (alloy 6)---R30006 (alloy 6)---17-4 SST HTS31600S31600S31600R31233R30006 Disk Seat &retainerR30006 (alloy 6)---S31603 CRPLR30006 Disk Seat &retainerR30006 (alloy 6)---316 SST withelectroless nickelcoating (ENC)S31600disk retainer withCoCr-A disk seatR30006 (alloy 6)---316 SST withelectroless nickelcoating (ENC)S31600disk retainer withCoCr-A disk seatR30006 (alloy 6)---Trim DesignationValve PlugCage1 (typically used with optionalmetal-seat constructions in alldesigns and body materialsexcept CF8M)S41600 HT17-4 SST HT17-4 SST HT HT(5)17-4 SST HT(5)34(7)5(5)6(5)2728(8)S31600 with seat andguide hard facedwith CoCr-Ahardfacing alloyS31600S31600 with seat andguide hard faced withCoCr-A hardfacingalloyS31600 with seat andguide hard faced withCoCr-A hardfacingalloyS31600 with seat andguide hard facedwith CoCr-Ahardfacing alloyS31600 with seathard faced withCoCr-A hardfacingalloy29 (standard for CF8M bodies inall designs regardless of seatconstruction)(8)S31600316 SST withelectroless nickelcoating (ENC)S31600S31600S3160037 and 37H (trim 37H hasclearances for high-temperatureservice above 210 C [410 F])S31600with seat and guidehard faced withCoCr-A17-4 SST HTS31600disk retainer withCoCr-A disk seatSeat Ring:R30006 (alloy 6)---17-4 SST HT(5)S31600------57 (standard for standardPTFE-seat ET, EAT, ETR in all bodymaterials except CF8M)17-4 SST HT(5)316LS31603316L SST withelectroless nickelcoating (ENC)S31603S31603---316L HFS31603 with seat andguide hard facedwith CoCr-Ahardfacing alloy316L SST withelectroless nickelcoating (ENC)S31603 disk retainerwith CoCr-A disk seatR30006 (alloy 6)---S41600 HT1. For NACE MR0175 / ISO 15156 and MR0103 specification trims, see table 182. For Cavitrol III trims, see table 6.3. For Whisper Trim III trims, see table 84. CA15 is used for NPS 6 and 8 full-sized and restricted-trim valves.5. For 8-inch Whisper Trim I.6. For 4, 6, and 8-Inch WhisperFlo trims, see table 7.7. Not for use with Whisper Trim I.8. Not for use with Whisper Trim I with 136 mm (5.375 inch) and larger ports.10
Product BulletinET Valve51.1:ETOctober 2020D100022X012Table 6. Cavitrol III(1) Metal Trim Part Materials and Body/Trim Temperature CapabilitiesTRIMDESIGNATION76VALVEPLU
www.Fisher.com Fisher ET, EAT, and ETR Sliding-Stem Control Valves Fisher ET, EAT, and ETR general-purpose control valves (figures 1, 2, and 3) are used for throttling or on-off
IP Office Essential Edition - Issue 1a (16 May 2010) ETR Telephones: 1. ETR Telephones The IP Office PARTNER Version supports the ETR Series of Avaya phones. The models supported are the ETR 6D, ETR 18D and ETR 34D phones. Feature ETR 6ETR 6DETR 18ETR 18DETR 34D Programmable buttons with lights 4 4 16 16 32 Programmable buttons without lights 0 .
www.Fisher.com D100022X012 Design ET, EAT, and ETR Sliding-Stem Control Valves Design ET, EAT, and ETR general-purpose control valves (figures 1, 2, 3, and 4) are used for throttling or on-off control of a wide variety of liquids and gases. All three valve designs have single ports, balanced valve plugs, and cage guiding.
ETR PR-06 Form Using the ETR Form document The ETR Form is a dynamic .pdf file that will change format as data is entered. Input fields expand to accommodate content. Some sections may be duplicated as needed. Some sections may be omitted based on user responses. Fields such as names and dates are linked to reduce duplication of entry.
Scalarexponential: Matrixexponential: eat 1 at a2t2 2! a3t3 3! . eAt I At A2t2 2! A3t3 3! . ea 0 1 eA I e at 1 eat e At eAt 1 ea (t1 2) eat1eat2 eA 1 t2) eAt1eAt2 e(a1 2)t e1tea2t e(A1 A2 eA1te 2t onlyifA 1A2 A2A1 d dt e at ae eata d dt eAt AeAt eAtA t 0 eatdt 1 a eat 1 t 0 eAtdt A 1 eAt I eAt I A 1 ifA
spaige@eat.uk.com mmota@eat.uk.com vwood@eat.uk.com flewis@eat.uk.com 01924 478 482 Reach Academy Head Teacher Hannah Lord hlord@eat.uk.com 01924 478 482 Ethos College DSL Diane Dunn ddunn@eat.uk.com 01924469170 07803508293 Ethos College DDSLs Lucy Beeby Michelle Brown lbeeby@eat.uk.com mbrown@eat.uk.com 07803508245 07803508232
If information provided by the parent is listed on the ETR planning page, the information must appear in Part 1 and be summarized in Part 2 of the ETR. It should list relevant content relating to the student’s background, medical history, stren
6. Instruct the empl oyee to begin the test and to utilize maximum effort to cover the 4‐Minutes 7. Record the meter distance for the 4 ‐Minute test on the ETR ‐164 8. Sign the ETR‐164 and obtain the signature of the employee who was tested 9. Send ETR‐164 to the Physical Fitness inbox at Physicalfitness@dps.texas.gov in the format .
Study program Administrimi Publik (2012/2013) Fakulteti Shkencat Shoqërore Bashkëkohore Cikli i studimeve Cikli i parë (Deridiplomike) SETK 180 Titulli I diplomuar në administrim publik Numri në arkiv i akreditimit [180] 03-671/2 Data akreditimit 22.06.2012 Përshkrimi i programit Programi i Administratës publike ka një qasje multidiciplinare të elementeve kryesore të studimit në .
