2007 SUSPENSION Rear Suspension - H3
2007 Hummer H32007 SUSPENSION Rear Suspension - H32007 SUSPENSIONRear Suspension - H3SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONSFastener Tightening SpecificationsSpecificationMetricEnglish125 N.m92 lb ft76 N.m56 lb ft85 N.m63 lb ft85 N.m63 lb ft95 N.m70 lb ft35 N.m26 lb ft80 N.m59 lb ft80 N.m59 lb ft50 N.m37 lb ftApplicationLeaf Spring to Front Bracket NutLeaf Spring U-Bolt NutsSpring Shackle to Frame NutSpring Shackle to Leaf Spring NutShock Absorber Lower BoltShock Absorber Upper BoltsStabilizer Bar Lower Link NutStabilizer Bar Upper Link to Frame NutStabilizer Clamp BoltsREPAIR INSTRUCTIONSSTABILIZER SHAFT REPLACEMENTRemoval Procedure1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .2. Support the rear axle at curb height.IMPORTANT: Do not attempt to hold the stabilizer shaft link near the boot.Use the hex feature on the end of the stud. Failure to do socould damage the boot.MYSunday, March 29, 2009 9:31:439:31:39 PMPage 1 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 1: Removing/Installing Stabilizer Shaft-To-Link NutCourtesy of GENERAL MOTORS CORP.3. Remove the stabilizer shaft to link nut.MYSunday, March 29, 2009 9:31:40 PMPage 2 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 2: Stabilizer Shaft Insulator Bracket Mounting BoltsCourtesy of GENERAL MOTORS CORP.4.5.6.7.Remove the stabilizer shaft insulator bracket mounting bolts.Remove the stabilizer shaft.Remove the stabilizer shaft insulator brackets.Remove the stabilizer shaft insulators.Installation ProcedureMYSunday, March 29, 2009 9:31:40 PMPage 3 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 3: Stabilizer Shaft Insulator Bracket Mounting BoltsCourtesy of GENERAL MOTORS CORP.1.2.3.4.Install the stabilizer shaft insulators to the stabilizer shaft.Install the stabilizer shaft.Install the stabilizer shaft insulator brackets to the rear axle.Install the stabilizer shaft bracket mounting bolts.MYSunday, March 29, 2009 9:31:40 PMPage 4 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 4: Removing/Installing Stabilizer Shaft-To-Link NutCourtesy of GENERAL MOTORS CORP.NOTE:Refer to Fastener Notice .IMPORTANT: Do not attempt to hold the stabilizer shaft link near the boot.Use the hex feature on the end of the stud. Failure to do socould damage the boot.5. Install the stabilizer shaft to link nut.MYSunday, March 29, 2009 9:31:40 PMPage 5 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Tighten:1. Tighten the stabilizer bar link nut to 80 N.m (59 lb ft).2. Tighten the insulator bracket bolts to 50 N.m (37 lb ft).6. Remove the rear axle support.7. Lower the vehicle.STABILIZER SHAFT INSULATOR REPLACEMENTRemoval Procedure1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .2. Support the rear axle at curb height.Fig. 5: Stabilizer Shaft Insulator Bracket Mounting BoltsCourtesy of GENERAL MOTORS CORP.MYSunday, March 29, 2009 9:31:40 PMPage 6 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H33. Remove the stabilizer shaft insulator bracket mounting bolts.4. Remove the stabilizer shaft insulator brackets.5. Remove the stabilizer shaft insulators.Installation ProcedureFig. 6: Stabilizer Shaft Insulator Bracket Mounting BoltsCourtesy of GENERAL MOTORS CORP.1. Install the stabilizer shaft insulators to the stabilizer shaft.2. Install the stabilizer shaft insulator brackets to the rear axle.NOTE:Refer to Fastener Notice .3. Install the stabilizer shaft bracket mounting bolts.MYSunday, March 29, 2009 9:31:40 PMPage 7 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Tighten: Tighten the bolts to 50 N.m (37 lb ft).4. Remove the rear axle support.5. Lower the vehicle.STABILIZER SHAFT LINK REPLACEMENTRemoval ProcedureFig. 7: Removing/Installing Stabilizer Shaft-To-Link NutCourtesy of GENERAL MOTORS CORP.MYSunday, March 29, 2009 9:31:40 PMPage 8 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H31. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .2. Support the rear axle at ride height.IMPORTANT: Do not attempt to hold the stabilizer shaft link near the boot.Use the hex feature on the end of the stud. Failure to do socould damage the boot.3. Remove the stabilizer shaft link upper nut.4. Remove the stabilizer shaft link lower nut.5. Remove the stabilizer shaft link.Installation ProcedureMYSunday, March 29, 2009 9:31:40 PMPage 9 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 8: Removing/Installing Stabilizer Shaft-To-Link NutCourtesy of GENERAL MOTORS CORP.IMPORTANT: Do not attempt to hold the stabilizer shaft link near the boot.Use the hex feature on the end of the stud. Failure to do socould damage the boot.1. Install the stabilizer shaft link.NOTE:Refer to Fastener Notice .MYSunday, March 29, 2009 9:31:40 PMPage 10 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H32. Install the stabilizer shaft link mounting nuts.Tighten: Tighten the stabilizer bar link lower mounting nut to 80 N.m (59 lb ft). Tighten the stabilizer bar link upper mounting nut to 80 N.m (59 lb ft).3. Remove the axle support.4. Lower the vehicle.SHOCK ABSORBER REPLACEMENTRemoval ProcedureNOTE:The front shock absorbers of the vehicle are multifunctional. Inaddition to contributing to a smooth ride they also provide the onlystop to the front suspension when fully extended. Therefore, whenservicing the shock absorber, service replacement shock absorbersmust be equivalent to original shock absorbers in both extendedlength and strength. Use of shocks not complying to originalequipment or strength could result in suspension over-travel orshock breakage. Suspension over-travel may result in suspensioncomponent breakage.1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .2. Support the rear axle at ride height.MYSunday, March 29, 2009 9:31:40 PMPage 11 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 9: View Of Upper Absorber BoltsCourtesy of GENERAL MOTORS CORP.3. Remove the upper absorber bolts.MYSunday, March 29, 2009 9:31:40 PMPage 12 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 10: View Of Lower Shock Absorber Mounting Bolt & NutCourtesy of GENERAL MOTORS CORP.4. Remove the lower absorber nut and the bolt.5. Remove the absorber.Installation ProcedureMYSunday, March 29, 2009 9:31:40 PMPage 13 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 11: View Of Upper Absorber BoltsCourtesy of GENERAL MOTORS CORP.1. Install the absorber.NOTE:Refer to Fastener Notice .2. Install the upper absorber bolts.Tighten: Tighten the bolts to 35 N.m (26 lb ft).MYSunday, March 29, 2009 9:31:40 PMPage 14 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 12: View Of Lower Shock Absorber Mounting Bolt & NutCourtesy of GENERAL MOTORS CORP.3. Install the lower absorber bolt and nut.Tighten: Tighten the nut to 95 N.m (70 lb ft).4. Remove the rear axle support.5. Lower the vehicle.SHOCK ABSORBER DISPOSALCAUTION: Gas charged shock absorbers contain high pressure gas. Donot remove the snap ring from inside the top of the tube. If theMYSunday, March 29, 2009 9:31:40 PMPage 15 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3snap ring is removed, the contents of the shock absorber willcome out with extreme force which may result in personalinjury.CAUTION: To prevent personal injury, wear safety glasses whencenterpunching and drilling the shock absorber. Use care notto puncture the shock absorber tube with the centerpunch.MYSunday, March 29, 2009 9:31:40 PMPage 16 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3MYSunday, March 29, 2009 9:31:40 PMPage 17 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 13: Drilling Hole In Shock Absorber At Centerpunched LocationsCourtesy of GENERAL MOTORS CORP.1. Make an indentation 10 mm (0.4 in) from the bottom (4) of the tube (3) using acenterpunch.2. Clamp the shock absorber in a vise horizontally with the shock absorber rod (1) completelyextended.3. Drill a hole in the shock absorber at the centerpunch (4) using a 5 mm (3/16 in) drill bit.Gas or a gas/oil mixture will exhaust when the drill bit penetrates the shock absorber. Useshop towels in order to contain the escaping oil.4. Make an indentation in the middle (2) of the tube (3) with a centerpunch.5. Drill a second hole in the shock absorber at the centerpunch (2) using a 5 mm (3/16 in) drillbit. Oil will exhaust when the drill bit penetrates the shock absorber. Use shop towels inorder to contain the escaping oil.6. Remove the shock absorber from the vise. Hold the shock absorber over a drain panhorizontally with the holes down. Move the rod (1) in and out of the tube (3) to completelydrain the oil from the shock absorber.SPRING JOUNCE BUMPER REPLACEMENTMYSunday, March 29, 2009 9:31:40 PMPage 18 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 14: Spring Jounce Bumper ReplacementCourtesy of GENERAL MOTORS CORP.Spring Jounce Bumper ReplacementCalloutComponent NameNOTE:Refer to Fastener Notice .Fastener Tightening Specifications: Refer to Fastener TighteningSpecifications.Preliminary Procedure: Remove the rear tire and wheel. Refer to Tireand Wheel Removal and Installation .Rear Jounce Bumper Mounting Bolts (Qty: 4)1Tighten: 30 N.m (22 lb ft)MYSunday, March 29, 2009 9:31:40 PMPage 19 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H32Rear Jounce Bumper (Qty: 2)LEAF SPRING REPLACEMENTRemoval Procedure1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .2. Support the rear axle independently in order to relieve the tension on the leaf springs.3. Disconnect the rear park brake cable. Refer to Parking Brake Rear Cable Replacement Left Side or to Parking Brake Rear Cable Replacement - Right Side .4. Remove the absorber lower mounting nut and bolt. Refer to Shock AbsorberReplacement.5. Remove the trailer hitch if equipped. Refer to Trailer Hitch Replacement .MYSunday, March 29, 2009 9:31:40 PMPage 20 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 15: Removing/Installing U-Bolt Nuts & WashersCourtesy of GENERAL MOTORS CORP.6. Remove the U-bolt nuts (5) and washers (4).7. Remove the anchor plate (3).8. Remove the U-bolts (1).MYSunday, March 29, 2009 9:31:40 PMPage 21 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 16: Removing/Installing Rear Spring Hanger Bracket BoltCourtesy of GENERAL MOTORS CORP.9. Remove the rear spring hanger bracket nut and bolt.MYSunday, March 29, 2009 9:31:40 PMPage 22 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 17: View Of Front Spring Bracket BoltCourtesy of GENERAL MOTORS CORP.10. Remove the front spring bracket bolt.MYSunday, March 29, 2009 9:31:40 PMPage 23 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 18: Removing/Installing Leaf Spring AssemblyCourtesy of GENERAL MOTORS CORP.11. Remove the leaf spring assembly (1) from the vehicle.Installation ProcedureMYSunday, March 29, 2009 9:31:40 PMPage 24 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 19: Removing/Installing Leaf Spring AssemblyCourtesy of GENERAL MOTORS CORP.1. Install the leaf spring assembly (1) to the vehicle.MYSunday, March 29, 2009 9:31:40 PMPage 25 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 20: View Of Front Spring Bracket BoltCourtesy of GENERAL MOTORS CORP.2. Install the front spring hanger bracket bolt.3. Install the front spring hanger bracket nut.MYSunday, March 29, 2009 9:31:40 PMPage 26 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 21: Removing/Installing Rear Spring Hanger Bracket BoltCourtesy of GENERAL MOTORS CORP.4. Install the rear spring hanger bracket bolt.5. Install the rear spring hanger bracket nut.MYSunday, March 29, 2009 9:31:40 PMPage 27 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 22: Removing/Installing U-Bolt Nuts & WashersCourtesy of GENERAL MOTORS CORP.IMPORTANT: Do not reuse the U-bolts.6. Install the new U-bolts (1).7. Install the anchor plate (3).MYSunday, March 29, 2009 9:31:40 PMPage 28 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3NOTE:Refer to Fastener Notice .8. Install the U-bolt washers (4) and nuts (5).Tighten: Tighten the U-bolt nuts to 76 N.m (56 lb ft).9. Install the absorber lower mounting nut and bolt. Refer to Shock Absorber Replacement.10. Install the trailer hitch, if equipped. Refer to Trailer Hitch Replacement .11. Connect the rear park brake cable. Refer to Parking Brake Rear Cable Replacement Left Side or to Parking Brake Rear Cable Replacement - Right Side .12. Remove the rear axle support.13. Lower the vehicle.14. With the vehicle at trim height, tighten the front leaf spring to frame nut and the rear leafspring shackle nuts.Tighten: Tighten the front leaf spring nut to 125 N.m (92 lb ft). Tighten the rear leaf spring shackle nuts to 85 N.m (63 lb ft).SPRING SHACKLE REPLACEMENTRemoval Procedure1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .MYSunday, March 29, 2009 9:31:40 PMPage 29 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 23: Removing/Installing Shackle Nut & BoltCourtesy of GENERAL MOTORS CORP.2.3.4.5.Support the rear axle at ride height.Remove the shackle nut and the bolt from the frame.Remove the shackle nut and the bolt from the spring.Remove the shackle assembly from the vehicle.MYSunday, March 29, 2009 9:31:40 PMPage 30 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Installation ProcedureFig. 24: Removing/Installing Shackle Nut & BoltCourtesy of GENERAL MOTORS CORP.1. Install the shackle assembly to the spring.NOTE:Refer to Fastener Notice .MYSunday, March 29, 2009 9:31:40 PMPage 31 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H32.3.4.5.6.Install the shackle nut and bolt to the spring. Do not tighten.Install the shackle nut and bolt to the frame. Do not tighten.Remove the rear axle support.Lower the vehicle.With the vehicle at trim height, tighten the rear shackle nuts.Tighten: Tighten the rear shackle nuts to 85 N.m (63 lb ft).SHACKLE BUSHING REPLACEMENTTools RequiredJ 21474-01 Control Arm Bushing Service KitRemoval Procedure1. Remove the spring shackle. Refer to Spring Shackle Replacement.2. Remove the spare tire when servicing the left side bushing.MYSunday, March 29, 2009 9:31:40 PMPage 32 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 25: View Of Bushing FlangeCourtesy of GENERAL MOTORS CORP.3. Use a blunt punch to straighten out the bushing flange that comes through the inner frame.MYSunday, March 29, 2009 9:31:40 PMPage 33 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 26: Using J 21474-01Courtesy of GENERAL MOTORS CORP.4. Remove the spring shackle bushing using J 21474-01 .Installation ProcedureMYSunday, March 29, 2009 9:31:40 PMPage 34 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 27: Using J 21474-01Courtesy of GENERAL MOTORS CORP.1. Install the new spring shackle bushing using J 21474-01 .MYSunday, March 29, 2009 9:31:40 PMPage 35 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 28: View Of Bushing FlangeCourtesy of GENERAL MOTORS CORP.2. Pull the spring shackle bushing into the frame rail until the flanged portion of the springshackle bushing is flush with the rail.MYSunday, March 29, 2009 9:31:40 PMPage 36 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H3Fig. 29: View Of Spring Shackle Bushing Inner FlangeCourtesy of GENERAL MOTORS CORP.3. Use a blunt punch to stake or flare the spring shackle bushing inner flange.4. Install the spare tire when servicing the left side bushing.5. Install the spring shackle. Refer to Spring Shackle Replacement.WHEEL STUD REPLACEMENTTools RequiredJ 43631 Ball Joint RemoverRemoval Procedure1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .MYSunday, March 29, 2009 9:31:40 PMPage 37 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H32. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation .3. Remove the brake rotor. Refer to Rear Brake Rotor Replacement .Fig. 30: Removing Wheel Stud From Hub FlangeCourtesy of GENERAL MOTORS CORP.MYSunday, March 29, 2009 9:31:40 PMPage 38 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H34. Remove the wheel stud from the hub flange using the J 43631 .5. Remove the wheel stud from the hub flange.Installation ProcedureFig. 31: View Of Wheel Studs, Hub & Rotor Assembly - Rear (W/Dual Wheels)Courtesy of GENERAL MOTORS CORP.1. Install the new stud into the hub flange hole using firm hand pressure.2. Install 4 washers to the new wheel stud.MYSunday, March 29, 2009 9:31:40 PMPage 39 2005 Mitchell Repair Information Company, LLC.
2007 Hummer H32007 SUSPENSION Rear Suspension - H33.4.5.6.7.8.9.10.Thread a wheel nut onto the new stud with the flat side facing the front hub flange.Tighten the lug nut until the stud contacts the back of the hub flange.Remove the wheel nut.Remove the washers.Install the brake rotor. Refer to Rear Brake Rotor Replacement .Install the tire and wheel. Refer to Tire and Wheel Removal and Installation .Remove the safety stands.Lower the vehicle.DESCRIPTION AND OPERATIONGENERAL DESCRIPTIONThese vehicles use a leaf spring and a solid rear axle suspension system.The rear axle assembly is attached to multi-leaf springs with U-bolts. The front ends of the springsare attached to the frame at the front hangers with bolts and are isolated utilizing rubber bushings.The rear ends of the springs are attached to the frame with bolts at the shackles. The shackles alsoutilize rubber bushings for isolation. Shackles allow the springs to change position while thevehicle is in motion.Two direct double-acting shock absorbers provide ride control. The shock absorbers are anglemounted between the frame. The shock absorbers are attached to the anchor plate.The rear spring steel stabilizing shaft helps minimize body roll and sway during cornering. Therear stabilizer shaft is connected to the rear axle and the frame with the following components: The rubber insulatorsThe clampsThe link assembliesSPECIAL TOOLS AND EQUIPMENTSPECIAL TOOLSSpecial ToolsIllustrationTool Number/DescriptionMYSunday, March 29, 2009 9:31:41 PMPage 40 2005 Mitchell Repair Information Comp
2. Support the rear axle independently in order to relieve the tension on the leaf springs. 3. Disconnect the rear park brake cable. Refer to Parking Brake Rear Cable Replacement - Left Side or to Parking Brake Rear Cable Replacement - Right Side . 4. Remove the absorber lower mounting nut and bolt. Refer to Shock Absorber Replacement . 5.
1935-40 FORD Car and Pickup Suspension Parts 13 1935-1940 Frame and Suspension Parts Call 402.886.2275 or click: www.heinzmanstreetrods.com CHEVROLET DRIVETRAIN 1. Rear Spring Hanger 2. Rear Spring - Dodge or C.E. Slider 3. Rear End, Nova - others 4. Rear Shock Kit 5. Rear Sway Bar 6. Transmission Mount Kit
rear front base pairs rear front 1-pc multi-slot bases ext multi-slot bases rear front rear front anschutz . rear front base pairs rear front 1-pc multi-slot bases ext multi-slot bases rear front rear front} topper 30, 22 jet & mod 158 (pre 1973) 18 60a (48064)} handy rifle 82 (48082) herters} j9 45 (48045) 46 (48046) 402 (48108) s45 (48226 .
rear suspension 622-1m5 neway adz 246 46,000# rear air suspension 300 621-012 neway ad/ard/adz; hendrickson has; reyco 240ar, 10.00" ride height 431-001 standard axle seats in axle clamp group 624-010 60 inch axle spacing 888-003 manual dump valve for air suspension with indicator light and gauge 910-004 dual air rear suspension leveling valves
727602 Dump Trailers with Watson & Chalin TA-5000-DB-19 Air Suspension REAR M83122 BECK BUS Deck and 1/2 Bus - Trailing Wheel REAR M85301 BENSON TRUCK BODIES INC. A-20002 Models with Hendrickson Intraax Air Suspension REAR M85000 M89436 90044089 Models with Neway Air Suspension REAR M83124 BLUEBIRD BUS All American Series (FE & RE Models)
19. Install bolt, washer and nut into rear suspension and screw it to rear wing spar by hand. Bolt head must be oriented opposite to the flight direction. Tighten it by socket wrench. 20. The rear wing suspension cover with bolts. Shorter one is for the hole next to flap. 21. Install rear suspension attachment covers. 22.
FM LNG 6x4 Tractor - Rear Air Suspension - Contact Regional Business Manager before quoting FM 64T LA2 Chassis Dimensions [mm] WB Wheelbase 3900 A Overall Chassis Length 7630 D Center of rear axle to back of cab 2904 N Rear Overhang (Min.) 805 N Rear Overhang (Max.) 995 T Theoretical Wheelbase 4585 .
FH LNG 6x4 Tractor - Rear Air Suspension - Contact Regional Business Manager before quoting FH 64T LA2 Chassis Dimensions [mm] WB Wheelbase 3900 A Overall Chassis Length 7630 D Center of rear axle to back of cab 2910 N Rear Overhang (Min.) 805 N Rear Overhang (Max.) 995 T Theoretical Wheelbase 4585 .
as advanced engineering mathematics and applied numerical methods. The greatest beneÞt to the reader will probably be derived through study of the programs relat-' 2003 by CRC Press LLC. ing mainly to physics and engineering applications. Furthermore, we believe that several of the MATLAB functions are useful as general utilities. Typical examples include routines for spline interpolation .
