BP Strut Cat 2S - PIPE SUPPORTS
Static and Dynamic Restraints Catalog 09S
WARRANTYBergen-Power Pipe Supports, Inc. (“Bergen-Power”) warrants to the original buyer (the “Buyer”) of productsmanufactured by it that all such products will be free from defects in material and workmanship for a period of one(1) year after the date of shipment when used in the manner and for the purpose recommended by Bergen-Power.Bergen-Power does not warrant goods manufactured by other parties, except to the extent that such goods are coveredby a warranty to Bergen-Power. Notice of a claim for a breach of a warranty must be given to Bergen-Power withinthirty (30) days after the date that the Buyer first has knowledge of an alleged breach of warranty, but in no eventlater than one (1) year after the date of shipment. Bergen-Power’s obligations under this Warranty are limited to itsrepair or replacement of those products that it determines, to its satisfaction, are defective, and it shall not be liablefor any charge or expense incurred by the Buyer in repairing or replacing said products. Notwithstanding anythingelse contained herein to the contrary, Bergen-Power’s liability under this Warranty for defective products is limitedto the net sales price of such products. The foregoing constitutes the Buyer’s sole and exclusive remedy for defective products.In the event that Bergen-Power provides engineering design or fabrication services, the Buyer’s acceptance ofBergen-Power’s design or delivery of the products shall relieve Bergen-Power of all further obligations with respectto such design and fabrication, except to the extent that Bergen-Power may otherwise expressly provide in a productwarranty. In no event, shall Bergen-Power be responsible for design errors due to inaccurate or incomplete information provided by the Buyer or its representatives. Bergen-Power reserves the right to revise product design withoutnotification.THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDINGWARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHERMATTER. IN NO EVENT AND UNDER NO CIRCUMSTANCE SHALL BERGEN-POWER BE LIABLE FOR(A) PERSONAL INJURY OR PROPERTY DAMAGES OR (B) CONSEQUENTIAL, SPECIAL OR INCIDENTAL DAMAGES, WHETHER FOR BREACH OF CONTRACT OR WARRANTY, NEGLIGENCE OR ANYOTHER TORTIOUS ACT OR OMISSION. THIS WARRANTY SHALL NOT APPLY TO PRODUCTS THATHAVE BEEN SUBJECT TO ALTERATION OR REPAIR MADE BY A PARTY OTHER THAN BERGEN-POWER,ACCIDENT, ABUSE, OR MISUSE. THIS WARRANTY SUPERCEDES ALL CONTRARY OBLIGATIONSIMPOSED ON BERGEN-POWER BY ANY PURCHASE ORDER.The terms of this Warranty may not be modified or changed except by a writing signed by an authorized officer ofBergen-Power.
STATIC AND DYNAMIC RESTRAINTSBergen-Power Pipe Supports is a complete linemanufacturing and engineering organization offeringpipe hangers. supports, restraints and specialty devicesto support and control piping and equipment used infossil power generating stations, petro-chemical plantsand other industrial processing piping systems.In addition to our product line, representing one of themost complete in the industry, Bergen-Power providescomplete engineering and technical services, includinganalysis, hanger design and detailing, and other construction support programs. To provide effective distributionof our products and services, engineering and salesoffices are maintained in major cities throughout thecontinental United States.INDEXFigure No.PageIntroduction .2Structural Attachment1000 .3Rigid Strut Assemblies2015 .42250 .52252 .6Vibration Check – Sway bracesIntroduction .72300 .72301 .82302 .82303 .92304 .102305 .10Sway Brace Pipe Clamp6180 .11Hydraulic Shock and Sway ArrestorsIntroduction .122525 .132530 .14GENERAL NOTESOutline dimensions and data shown in this catalog are forreference only and are not intended for inspection purposes.Designs and dimensions are subject to change without notice.All hanger products shown herein are manufactured in accordance with industry standards and are for installation andservice as described. When used for other purposes or inways other than those for which designed and manufactured,Bergen-Power cannot be held responsible for product failure,injuries, or property damage.Cataloged products meet requirements of MSS-SP-58 andMSS-SP-69.Maximum rated loads for hangers are based on a safetyfactor applicable to the codes listed in this catalog or theallowable stresses specified in ASME B31.1, ASME B31.3,and MSS-SP-58.Restraint Yoke Clamp6175 .15Restraint Pipe Clamp6202 .176222 (Alloy) .17Off-axis Restraint Pipe Clamp6252 .19Restraint Riser Clamp6280 .216281 (Alloy) .21Welding Lug Attachment6410 .22Typical Arrangements .241
STATIC AND DYNAMIC RESTRAINTSINTRODUCTIONBergen-Power markets the widest selection of restraintassemblies and devices which allows the designer to selectdevices technically and economically suited for the specificapplication by type, size and configuration.Bergen-Power restraint systems now cover a broader rangeof load ratings and allow greater flexibility in field adjustment. High precision steel ball bushings and pins are nowstandard components throughout the line. Also included isa new series of restraint yoke clamps.Bergen-Power hydraulic snubbers have also been improvedand are available with options to better suit the differentconditions the application requires.SPECIFICATIONSAll Bergen-Power restraints are designed to meet requirements of: Manufacturers Standardization Society SP-58,Manufacturers Standardization Society SP-69 and ASMECode for Pressure Piping ASME B31.1 and Process PipingASME B31.3. Units meeting the requirements of theASME Boiler and Pressure Vessel Code, Section III arealso available in accordance with Bergen-Power loadcapacity data sheets.RIGID STRUT ASSEMBLIESRECOMMENDED SERVICE: Used to restrain movement of piping in one direction. Movement due to thermalexpansion in other directions should be evaluated.STANDARD DESIGN FEATURES: Designed to restrain tensile and/or compressive forces. Tight fitting connections allow positive control of pipingsystems. Spherical, self-aligning ball bushing at both ends of thestrut allow for 5 of angular motion or misalignment. Can be installed in any spatial orientation. Field adjustment is available in all assemblies. All welding work required in the field is recommendedto be fillet welds. Paint — Standard primer finish.HYDRAULIC SNUBBERASSEMBLIESGENERAL APPLICATION: Used for the control andprotection of piping and equipment subject to shock(impulse) loading and swaying (cyclic) conditions. Its usetransfers any imposed forces on the piping or equipmentdirectly to the building structure at the instant of shockoccurrence, while at all other times allowing free unrestricted movement through its normal operating range.SPECIFIC APPLICATIONS: Earthquake protection. To prevent damage by wind in outdoor installations. Employed at points in piping systems subject to shockloadings generated by quick closing valves, water hammer, relief valve reaction or other applied shock loads.STANDARD DESIGN FEATURES: Piping and/or equipment movement is controlled bytamper-proof dual stage flow control poppets designedwith self-cleaning orifices. Furnished as a complete, compact, and efficient unit,ready for immediate use. Manifold configuration requiring no external piping. Spherical, self-aligning ball bushings allow for 5 ofangular motion or misalignment. Pressurized hydraulic reservoir allows mounting in anyspatial orientation. Virtually no resistance to normal thermal movements ofthe piping. Paint — standard primer finish. Large restraining forces compared to size. Functions in restraining tension and compression. Stroke determination is made from built-in-datum pointlocated on piston rod wrench flats. Fluid Level Indicator — Provides concise determinationof exact fluid level in the unit, thereby eliminating estimate of reserve fluid level.OPTIONAL DESIGN FEATURES: Remote Reservoir Mounting – The snubber’s pressurized reservoir can be remotely mounted for snubberlocations that are difficult to reach. Integral Relief Valve — A non-adjustable valve, whichis factory preset at 133%, or 200% of rated load. Protective Boot – Installed over the piston rod for protection in corrosive and/or dusty areas. Rigid Strut Application — When no thermal growth isanticipated after lock-up an optional poppet valve, without bleed, is furnished. Must be ordered with optionalintegral relief valve.For information concerning Bergen-Power snubbersand snubber assemblies please contact your localBergen-Power Pipe Supports sales office.2
STATIC AND DYNAMIC RESTRAINTSSTRUCTURAL ATTACHMENTFigure 1000Size Range: 700 through 130,000 pounds ( 3,114 Nthrough 578,240 N) load.Material: Carbon steel except load pin which isstainless steel.Service: For attachment of struts to structures.Maximum Temperature.: 350 F (177 C) for therated loads shown.Features: Can be used as a second end attachment.Used With: Bergen‐Power Figure Numbers 2015, 2250,2252, 2525, 2530.Ordering: Specify Figure Number and size.For Metric applications specify Figure M1000 and size.NOTE: This product is designed to function with a10 cone of action, and a 90 arc of loading. Load‐ing beyond this cone or arc is not recommended.FIGURE 1000 ‐ STRUCTURAL 6690480,000355872130,0005782921 7/8482 1/4572 1/4572 7/8732 7/8733 7/8984 1/41085 5/81436 1/41598 1/22161/2135/8165/8167/8227/8221 3/8351 1/2381 11/16431 13/16462 1/16521 1/8291 1/2381 1/2383 1/2893 1/28951275 3/41467 1/41849 1/423511 5/82959/16143/4193/4191 1/2381 1/2382 1/8542 3/8603763 5/8924 5/81173/8101/2131/2133/4193/4191251 1/4321 1/2381 3/4442 1/2641/2133/4193/4191251251 1/2381 3/4442 1/4572 1/2643 1/4831/2131/2131/2133/4193/4191251 1/4321 1/2381 3/4441 3/4441 1/2381 3/4441 3/4443 1/4833 1/4834 1/4108512761527 3/41978 GRAMSTORQUEINCH‐POUNDSNEWTON‐METERS3
STATIC AND DYNAMIC RESTRAINTSLIGHT DUTYRIGID ROD STRUTFigure 2015Size Range: 700 to 4,000 pounds ( 3,114 N to17,792 N ) load.Material: Carbon steel except load pin which isstainless steel.Service: For rigid restraint applications whereshort pin to pin dimensions are required.Installation: Securely fasten end bracket to struc‐ture. Screw rod into paddles and adjust for thedesired overall length. Fasten strut to pipe attach‐ment (in place). After all minor adjustments aremade the unit is locked by tightening the hex nutagainst the paddle.NOTE: Rods should be visible in paddle sightholes to insure proper thread engagement.Field Adjustment: Plus or minus 1½ inch (38 mm).Used With: Bergen‐Power Figures 6175,6202,6222, 6252.Ordering: Specify figure number, size, strut length(pin to pin length) and customer mark number (ifany). Restraint attachments must be ordered sepa‐rately. For Metric applications specify Figure M2015.FIGURE 2015‐ LIGHT DUTY RIGID ROD CELSUISP TO PMIN.MAX.10 3/43327383810 3/43327383813 AEP3/4193/4191251 7/8482 1/4572 TERSRS11 1/225381 1/8 1 1/229381 1/4 1 3/43244T1/2135/8165/816WGT @ MIN.P TO P62.794.1125.4TORQUE (Q)(NOMINAL)152015203547
STATIC AND DYNAMIC RESTRAINTSADJUSTABLE RIGID STRUTFigure 2250Size Range: 700 through 130,000 pounds ( 3,114 Nthrough 578,240 N) load.Material: Carbon steel except load pin which isstainless steel.Service: For rigid restraint applications allowing thegreatest amount of field adjustment without fieldwelding.Installation: Securely fasten end bracket to struc‐ture. Attach strut paddle to end bracket. Adjust strutfor the desired overall length. Fasten strut to pipeattachment (in place). After all minor adjustments aremade, the unit is locked by tightening the hex nutsagainst the extension piece.NOTE: Rods should be visible in the sight holes ateach end of the strut to assure proper thread engage‐ment. Special lengths or other increments availableupon request.FIELD ADJUSTMENT: Plus or minus two inches (51 mm)(minimum).Used With: Bergen‐Power Figure Numbers 6175, 6202,6222, 6252.Ordering: Specify figure number, size, strut length(pin to pin length) and customer mark number (ifany). For Metric applications specify Figure M2250.FIGURE 2250 ADJUSTABLE RIGID 0,000578292P TO 30481203048120304812030481203048DIMENSIONS MILLIMETERSCELSUISNEWTONS KILOGRAMSPIPE SIZEEPRST1 7/8482 1/4572 1/4572 7/8732 7/8733 7/8984 1/41085 5/81436 1/41598 1/22163/8101/2131/2133/4193/4191251 1/4321 1/2381 3/4442 1/2641251 1/8291 1/4322512512 5/8672 5/8673 5/8924 1/810561521 1/2381 1/2381 3/4442 1/2642 1/2643763 1/2893 1/28941025 1/41331/2135/8165/8167/8227/8221 3/8351 1/2381 11/16431 13/16462 1/1652D1 1/2401 1/2402502 1/2652 1/2653803 521/831/831/831/461/461/461/463/8103/8101/213WGT. @ MIN.P TO PTORQUE 136560100254136TORQUEINCH‐POUNDSNEWTON‐METERS5
STATIC AND DYNAMIC RESTRAINTSFIELD WELDED ADJUSTABLERIGID STRUTFigure 2252Size Range: 700 through 130,000 pounds ( 3,114 Nthrough 578,240 N) load.Material: Carbon steel except load pin which isstainless steel.Service: For rigid restraint applications where pinto pin dimension is to be determined in the field.All struts will be shipped at maximum pin to pindimension.Installation: Determine pin to pin dimension, cutstrut tube to required length and weld adapter end tostrut. Securely fasten end bracket to structure. Adjuststrut to desired overall length. Fasten strut to pipeattachment (in place). After all minor adjustmentsare made, the unit is locked by tightening the hexnuts against the extension piece.Note: Rods should be visible in the sight holes ateach end of the strut to assure proper thread engage‐ment. One end shipped loose for field welding.Field Adjustment: Plus or minus four inches(102 mm) after final welding.Note: For sizes and dimensions refer to Figure 2250 on page 5.For sizes 60 thru 130 insert field weld adapter into 1" pipe and weld.Ordering:dSpecifyf part number,b size, andd customermark number (if any). For Metric applications specifyFigure STORQUEINCH‐POUNDSNEWTON‐METERS
STATIC AND DYNAMIC RESTRAINTSVIBRATION CHECK‐SWAY BRACESSpecifications: All Bergen‐Power Pipe Support VibrationCheck‐Sway Braces are designed to meet the requirement of:Manufacturers Standardization Society SP‐58Manufacturers Standardization Society SP‐69,and ASME Code for Pressure Piping ASME B31.1and ASME B31.3.Type Selection: Specify a Figure 2303 where adjustabilityof the preload is desired, in most other cases a Figure2300 is usually sufficient.Size Selection: The size of the vibration check‐sway braceis determined by calculating the amount of resistive forcerequired by the sway brace to overcome the inertia force ofthe vibrating object. This is done by taking into considera‐tion the mass, amplitude, frequency and angle of approachof the sway brace from the axis of movement.How To Size Assemblies: The Figures 2301 and 2304assemblies are recommended where the pin to pin dimen‐sions are small. For assemblies with large pin to pin dimen‐sions, use the Figure 2302 or 2305 assemblies. Refer to theindividual assemblies for maximum lengths.Final Setting: The sway brace should be in the neutral(zero force) position when the system is HOT and operat‐ing. If not, the rod coupling must be turned to readjust tothe neutral position.Ordering: Specify figure number, size, pipe size, preload aand length (pin to pin length), customer mark number (ifany). Pipe clamp, Figure 6180, must be ordered separately.For Metric applications specify Figures M2300M2300, M2301M2301,M2302, M2303, M2304, M2305.Bergen‐Power Pipe Supports has designed its units into sixsizes, based on past experience, relating to specific pipesizes. In general, we recommend the use of these sizes.Size Range: Preloads from 60 to 2,000 pounds ( 267 N to8,896 N) up to maximum forces of 240 to 8,000 pounds( 1,068 N to 35, 584 N).Service: For controlling vibration, to prevent externallycaused pipe sway, as an energy resisting device to opposeshock forces and as a guide or restraint to control pipe linemovements.Temperature: 350 F (177 C) for all components exceptpipe clamp and temperature effect on spring coil.Features: Compact and suitable for use in a confined space. Each size has 3” (76mm) of travel in either direction. All steel construction to protect the spring againstdamage and weather conditions. Nameplate and movement indicator plate are anti‐corrosive. These plates are mechanically fastenedto prevent accidental removal. Paint — standard primer finish. Rod coupling allows for field adjustment.Optional Feature: Corrosion Resistant — available forprotection against moderate corrosive conditions or severeweather. The unit is galvanized, per ASTM A‐153, exceptthe spring which is neoprene coated. The final closure weldat time of assembly is metalized.metalizedSINGLE ADJUSTMENTSWAY BRACEFigure 2300FIGURE 2300 ‐ SINGLE ADJUSTMENT SWAY BRACERATED LOADSPRINGSizeAINITIAL MAX.RATELOADLOAD16024060 lbs./in.3/41267106811 N/mm192175700175 lbs./in.12778311431 N/mm2535002000 500 lbs./in.132224889688 N/mm2541,0004000 1000 lbs./in. 1 1/44444817793 175 N/mm3251,5006000 1500 lbs./in. 1 1/25667226689 263 N/mm3862,0008000 2000 lbs./in. 1 1/26889635586 350 N/mm38EHJLW12 1/431113 1/833317 7/845417 1/843519 3/849221 1/45401 1/2381 3/4441 3/4442512 1/2642 1/2641251 1/4321 1/4321 1/2382512518 5/8219922913 3/434912 5/832113 7/835215 3/44004 3/81114 3/81114 3/81116 1/21656 1/21656 : 1) Length adjustment is 1‐1/2" (38mm) in either direction when installed in an assembly.2) Each size has 3" (76mm) travel in either direction.DIMENSIONS EINCH‐POUNDSNEWTON‐METERS7
STATIC AND DYNAMIC RESTRAINTSSINGLE ADJUSTMENT SWAY BRACE ASSEMBLIESFigure 2301Figure 2302FIGURE 2301, 2302 ‐ SINGLE ADJUSTMENT SWAY BRACE FIGURE2300†SIZE112233445566EE1E212 1/431113 1/833317 7/845417 1/843519 3/849221 1/454018 1/247019 5/849824 3/861924 1/861327 1/8689297372 1/264376376376376376* Minimum P to P for Part 2302 is maximum P to P for Part 2301.† Refer to Part 2300 for rated loads, complete dimensions and STORQUEINCH‐POUNDSNEWTON‐METERSMIN.230119 1/249521 3/854326 1/866426 3/867029 5/875231 1/2800P TO PMAX.230136 1/492137 1/894341 7/8106441 1/8104543 3/8110245 2591W11/831/831/833/1651/461/46
STATIC AND DYNAMIC RESTRAINTSDOUBLE ADJUSTMENT SWAY BRACEFigure 2303Preload Adjustment:Turn the adjuster nuton the structuralattachment end untilthe desired preload isattained. Turn thecompression nut untilit takes up the slack.Lock in position.Note that the indicat‐ed deflection must begreater than the ther‐mal movement.FIGURE 2303‐ DOUBLE ADJUSTMENT SWAY BRACE ASSEMBLYRATED LOADSPRINGINITIALMAX.RATELOADLOADSIZEA16024060 lbs./in.3/41267106811 N/mm192175700175 lbs./in.12778311431 N/mm2535002000500 lbs./in.132224889688 N/mm2541,00040001000 lbs./in.1 1/44444817793175 N/mm3251,50060001500 lbs./in.1 1/25667226689263 N/mm3862,00080002000 lbs./in.1 1/26889635586350 N/mm38E17 5/844819 1/4489246102461027 3/869529 1/4743H4 5/81175 1/81305 1/81305 5/81436 1/41596 1/4159J1251 1/4321 1/4321 1/2381 3/4441 3/444L9 1/22411025414 3/437513 3/434915 5/839717 1/2445W4 3/81114 3/81114 3/81116 1/21656 1/21656 1/2165NOTES: 1) Length adjustment is 1‐1/2" (38mm) in either direction when installed in an assembly.2) Each size has 3" (76mm) travel in either direction.3) Either of the two forces is adjustable up to the maximum rated load.DIMENSIONS AMS NEWTON‐METERS9
STATIC AND DYNAMIC RESTRAINTSDOUBLE ADJUSTMENT SWAY BRACE ASSEMBLIESFigure 2304Figure 2305FIGURE 2304, 2305 ‐ DOUBLE ADJUSTMENT SWAY BRACE FIGURE2303†SIZE112233445566E17 5/844819 1/4489246102461027 3/869529 1/4743E123 5/860025 3/465430 1/27753178735 1/889237940E22 1/264376376376376376* Minimum P to P for Part 2305 is maximum P to P for Part 2304.† Refer to Part 2303 for rated loads, complete dimensions and MSTORQUEINCH‐POUNDSNEWTON‐METERSMIN.230424 7/863227 1/269932 1/481933 1/484537 5/895639 1/21003P TO PMAX.230441 5/8105743 1/4109948121948121951 3/8130557 2794W11/831/831/833/1651/461/46
STATIC AND DYNAMIC RESTRAINTSSWAY BRACE PIPE CLAMPFigure 6180Size Range: 2 through 24 inches (50 mm to 600 mm).Material: Carbon SteelFinish: PlainService: For use with our standard line of sway brace .assemblies only, in the control of vibration and shockloading.Maximum Temperature: 650ºF (343ºC) for ratedloads shown.Features: Tight fitting load pin.Size Selection: See the chart shown below to matchthe appropriate clamp to the desired sway braceassembly.Ordering: Specify figure number and pipe size.For Metric applications specify Figure M6180.FIGURE 6180 ‐ SWAY BRACE PIPE CLAMPASSEMBLYSIZE1PIPESIZE2502 1/2653803 1/290E3ASSEMBLYSIZE5 1/81305 1/21405 15/161516 3/161572PIPESIZE4100512561508200E36 1/216571788 5/82199 10 5/827011 7/83021333013 14 7/837816 1/441317 1/843518 TON‐METERSE3* Sizes 5 and 6 as specified by customer.DIMENSIONS POUNDSNEWTONS11
STATIC AND DYNAMIC RESTRAINTSSHORT STRUT HYDRAULICSNUBBERFigure 2525Size Range: Available in seven sizes from 3,000to 130,000 pounds (3,114 N through 578,240 N)load and stroke lengths of 6, 12, and 18 inches(152 mm, 305 mm, and 457 mm).Service: For dynamic restraint applications requir‐ing the smallest overall assembly length in tight fitapplications.Piston Rod Setting: The factory will preset andclamp the piston rod at the proper cold installingstroke position. Unless specified otherwise, thissetting will position the piston so that its calculat‐ed thermal movement will straddle the mid‐strokeposition of the unit, giving equal reserve at eachend of the stroke. See Installation Instructions todetermine or change piston rod setting.Used With: Bergen‐Power Figures 6175, 6202,6222, 6252, 6520, 6521, 6525, 6526.Ordering: Specify figure number, size, cylinderstroke, thermal movement and direction (tensionor compression), preset, overall assembly length(pin to pin length), options (if any), and customermark number (if any). Restraint attachments mustbe ordered separately. For Metric applicationsspecify Figure M2525.FIGURE 2525 ‐ SHORT STRUT HYDRAULIC SNUBBERINCHES/MMSIZEMAX. 130,000578240CYL.BORE1 1/2382 1/2643 1/4834102512761528203P TO P†MIN. 22 3/4578266602973731 3/87973383836 3/493342 5/161075E2 1/4572 7/8733 7/8984 1/41085 5/81436 1/41598 1/2216H*L †L1518 1/4 4 1/2127464114619 3/4 6 1/41525021596 3/8 21 3/8 7 5/81625431948 1/2 22 1/2 8 7/821657222510 1/4231026058425411 7/82511 3/43026352981628 7/16 13 7/8406722352PR1/2133/4191251 1/4321 1/2381 3/4442 1/2641 1/4322512 5/8672 5/8673 5/8924 1/81056152WGT. PRESET(APPROX.)MIN. MAX. 1 3/45/83/4 6 3/435441619171162 1/27/83/4 6 3/4706422191713231 3/83/4 6 3/4125763519171573 1/2 1 1/23/4 6 3/4155893819171703 1/2 1 11/16 3/4 6 3/425589431917111641 13/16 3/4 6 3/441010246191711865 1/4 2 1/16 3/4 6 3/48051335219171365ST† Unit length fully retracted. Dimensions shown are for 6"/152mm stroke unit.For 12"/304mm and 18"/457mm stroke units add stroke difference.* Envelope STORQUEINCH‐POUNDSNEWTON‐METERS13
STATIC AND DYNAMIC RESTRAINTSADJUSTABLE STRUT HYDRAULIC SNUBBERFigure 2530SIZE RANGE: Available in seven sizes from 3,000 to 130,000pounds ( 3,114 N through 578,240 N) and stroke lengths of6, 12, and 18 inches (152 mm, 305 mm, and 457 mm).SERVICE: For dynamic restraint applications allowing thegreatest amount of field adjustment or where the exactoverall length must be determined on‐site.USED WITH: Bergen‐Power Figures 6175, 6202, 6222,6252, 6520, 6521, 6525, 6526.ORDERING: Specify figure number, size, cylinder stroke,thermal movement and direction (tension or compression),preset, overall assembly length (pin to pin length), options(if any), and customer mark number (if any). Restraintattachments must be ordered separately. For Metricapplications specify Figure M2530.FIGURE 2530 ‐ SHORT STRUT HYDRAULIC SNUBBERSIZEMAX. 130,000578240P TO P†MAX.MIN.c33 3/864848162636 7/888937223540 1/81061019269242 7/81091089276945 3/41781162452150 1/42111276535957 9/1623214625893INCHES/MME15 1/838417 1/843518 3/447620 3/851822 3/457825 1/464129 1/8740PIPE SIZE2502 1/2653803 1/290512561508200For Dimensions not given refer to Figure 2525.† Unit length fully retracted. Weight shown is for minimum P to P and 6"(152mm) stroke unit.cDimensions shown are for 6"/152mm stroke unit.For 12"(304mm) and 18" (457mm) stroke units add stroke GHT(APPROX.) 763547100136100136100136100136100136100136
PIPE CLAMPS AND ATTACHMENTSON‐AXIS RESTRAINTYOKE CLAMPSFigure 6175Size Range: 700 to 130,000 pounds ( 3,114 Nthrough 578,240 N) load.Material: Carbon steel except U‐bolt which isalloy steel, and load pin which is stainlesssteel.Finish: PlainMax. Temp.: 650ºF (343ºC).Service: For non‐integral on‐axis attachment tothe piping system in restraint applications.Used With: Bergen‐Power Figures 2015,2250, 2252, 2525, 2530.Ordering: Specify figure number, load sizeand pipe size. Strut assembly must be orderedseparately. For Metric applications specifyFigure M6175.NOTE: This clamp is designed to function withina 10º cone of action, perpendicular to the pipe.Loading beyond this cone is not recommended.FIGURE 6175 ‐ ON‐AXIS RESTRAINT YOKE CLAMPSSIZEMAX. 130,000578,240INCHES/MMD3/4193/4193/4191 1/4321 1/4322512 1/2642 1/2643 1/4834102G1/2135/8165/8167/8227/8221 3/8351 1/2381 11/16431 13/16462 1/1652P3/8101/2131/2133/4193/4191251 1/4321 1/2381 3/4442 1/264T1251251 1/4321 3/4441 3/4442 1/2643763 1/28961528203TORQUE 013565257128351132NOTE: "E" Dimension is shown on following page.DIMENSIONS MILLIMETERSCELSUISNEWTONS KILOGRAMSTORQUEINCH‐POUNDSNEWTON‐METERS15
PIPE CLAMPS AND ATTACHMENTSFIGURE 6175 – ON AXIS RESTRAINT YOKE 80808080,000355,840130130130,000578,240E WGT. E WGT. E WGT. E WGT. E WGT. E WGT. E WGT. E WGT. E WGT. E WGT.6464.5658138131521.8 152 2.01522.3 2035.9 203 5.961 2561 25.56 1 2681 21581 2151652.3 165 2.51652.7 2166.8 216 6.871 16671 16671 16 6.51792.7 179 2.71792.979 16679 16779 168 99 1624 99 16 24 109 16 341922.7 192 3.21923.6 24311243 112681599 16999 16 1099 1611 109 16 24 109 16 24 119 16
Bergen-Power Pipe Supports, Inc. (“Bergen-Power”) warrants to the original buyer (the “Buyer”) of products manufactured by it that all such products will be free from defects in material and workmanship for a period of one (1) year after the date of shipment when used in the manner and for the purpose recom
2007 cat d6t xl 2012 cat d6t lgp (3) 2006 cat d6r xl series iii 2004 cat d6r lgp 2012 cat d6n lgp (2) 2012 cat d6k-lgp (4) cat d6h lgp cat d6h 2012 cat d5k2-xl (3) 2008 cat d4g 2012 cat d3k lgp (3) 2002 john deere 750c 2006 john deere 700lgp 2013 komatsu d39 px motor graders cat 16g 2014 cat
2011 Cat 950H (1 of 3) 2008 Cat 740 2007 Cat D6R 20 April Rockingham Circuit, United Kingdom UNRESERVED PUBLIC AUCTION. . Crawler Loader 2006 Cat 953C Crawler Tractors 2007 Cat D6N LGP 2007 Cat D6R 2007 Cat D6R LGP Excavators 2013 Cat 308E 2012 Cat 308E (2) 2007 Cat D6R
Cat C2.4 (DI Turbo) Cat C4.4 Cat C7.1 ACERT Cat C4.4 ACERT Cat C7.1 ACERT Cat C7.1 Cat C7.1 Cat C9.3B Cat C7.1 ACERT Cat C9.3 Cat C13 Engine 47 91 157 143 157 260 212 311 259 346 405 Net Horse Power (hp) 0.25 0.65 1.2 1 1.3 - 1.4 1.8 1.6 2.12 1.88 2.69 2.41 - 3.21 Bucket Capacity (m3) Large boom base for strength and .
Anvil-Strut Cross Reference Guide B-LINE 2 * Comparable with some deviation in dimension or configuration. B-Line Number Anvil-Strut Number B-Line Number Anvil-Strut Number B-Line Number Anvil-Strut Number B-Line Number Anvil-Strut Number ATR G
strut is available with hanger rod, washers & nuts, beam clamps, strut cover, strut buckles and end sealant. It is sold in ten foot lengths. Trough, Wireway & Strut Attributes . PVC Coated Pipe Straps FT6612 2" 1" 3" 4" PVC Coated Pipe S
Anvil Steel Pipe Nipples & Steel Pipe Couplings SPF Steel Pipe Nipples Merit Tee-lets, Drop Nipples & Steel Welding Flanges SPF O'lets Anvil Pipe Hangers & Supports, All Thread Rod Anvil-Strut Strut & Strut Fittings Mueller Valves Mueller Indicator Posts
of Grip Strut Grating cushions the impact of walking, lessening worker fatigue and increasing efficiency. Heavy-Duty Grip Strut Safety Grating products offer the advantage of regular Grip Strut Safety Grating (detailed in Catalog GSSGST-09), but are designed for applications of great
22-796900 US&R Rescue Support System (qty. 1 kit below) 1 (including (2) 6 ft Deployable Raker Kits shown in listing) 22-796212 AcmeThread Strut 12-15 in. 4 22-796206 AcmeThread Strut 19-25 in. 4 22-796200 AcmeThread Strut 25-36 in. 4 22-796202 AcmeThread Strut 37-58 in. 4 22-796204 AcmeThread Strut
