7500 CrownPro AcidShield Novolac Epoxy

2y ago
10 Views
2 Downloads
430.27 KB
5 Pages
Last View : 5d ago
Last Download : 2m ago
Upload by : Wren Viola
Transcription

7500 CrownPro AcidShield Novolac EpoxyTECHNICAL DATA SHEETProduct Number: 7500Chemical Resistant Novolac Epoxy Liner, Medium Viscosity Coating and Mortar BinderDESCRIPTION7500 CrownPro AcidShield is a multifunctional phenol novolac resin that is extremely chemical resistant with a high heatdeflection temperature. 7500 CrownPro AcidShield is a moderate viscosity thick film novolac lining designed to cure atambient temperatures to provide superior corrosion protection for surfaces in severe chemical and physical environments.It can be applied directly over 8303 CrownShield MVB (moisture mitigation primer). It is VOC Compliant in all states andprovinces in North America.TYPICAL USES Crude Oil Storage Tanks Food Processing Facilities Internal Tank and Pipe Lining Mining and Milling Industries Petrochemical Plants Power Generating Plants Pulp and Paper Industry Steel Structures and Bridges Secondary Containment Floors and Walls Semi-Conductor Manufacturing and Etching Water and Wastewater Treatment PlantsBENEFITS Complies with USDA, FDA, Food Safety ModernizationAct. See Crown Polymers Technical Bulletin: 3 Foodand Beverage Compliance. Slip Resistance (ADA) See Crown Polymers TechnicalBulletin: 4 Coefficient of Friction. LEED and Green Seal requirements. See CrownPolymers Technical Bulletin: 5 LEED and GreenSeal Information. 100% Solids, Zero VOC and EPA Compliant, andlow odor during installation. Cures to an inert finish.See Crown Polymers Technical Bulletin: 2 VOCCompliance. Strong and Tough Floor. Superior Chemical and Abrasion Resistance Designed for new floors and for resurfacing old floorsand wallsLIMITATIONS This product is best suited for applications intemperatures between 60 F to 90 F (16 C to 32 C). Scratches in certain colors may appear white, such asblue pigmented products. Higher temperatures will result in shortened workingtimes and faster drying time. Color may vary due to batch to batch variation, always“box” different batches to avoid it. Do not use as a primer when concrete slab exceeds 3lbs. or 80% RH.COLORSPigmented only, 15 Standard Colors* and Custom Colors.Available in factory pigmenting or CrownPigment Epoxy 6300 PigmentPack *See Crown PolymersStandard Color Guide Acrylics, Epoxies, Polyaspartics,Polyurethanes (PigmentPack).COVERAGE RATE PER GALLON Primer: 100 to 160 sq. ft. (9.3 to 14.9 sq. m.) WFT 10to 16 mils (0.20 to 0.25 mm) Coating: 100 to 160 sq. ft. (9.3 to 14.9 sq. m) WFT 10to 16 mils (0.25 to 0.41 mm) Broadcast and Trowel: Varies Depending on thicknessof system selected. 1/16 to 1/4 inch (1.59 to 6.35 mm)and more.CONCRETEConcrete must be structurally sound and free of curingagents, coatings, sealers, densifiers, and other bondbreakers.New Concrete: Place concrete per ACI 302.2R Guide for ConcreteSlabs that Receive Moisture-Sensitive Floor Materials. Water Cement Ratio 0.4 to 0.5, and an approximate4,000 psi (28 MPa) strength level. Requiring a positive side moisture barrier in directcontact with the concrete meeting ASTM E1745Standard Specification for Plastic Water RetardersUsed in Contact with Soil or Granular Fill underConcrete Slabs. The moisture barrier needs to be placed per ASTME1643 Standard Practice for Selection, Design,Installation of Water Vapor Retarders Used in Contactwith Earth or Granular Fill Under Concrete Slabs,Class A 15 mils (0.38mm)Existing Concrete:If field tests or laboratory analysis reveals inferior concreteflooring slabs containing contaminants from previouslyapplied unreacted silicate materials that will interfere withthe bond, use 8201 CrownPrime WBC Primer. See CrownPolymers Technical Bulletin: 20 Selecting a Primer. Contaminants include, but are not limited to organicCP 7500 CrownPro AcidShield Novolar Epoxy Medium Viscosty TDS 20210223 DMPage: 1 of 5

hydrocarbon materials, calcium chlorides, andaluminum stearates. Concrete flooring slabs can lose their structuralstrength over time, caused by conditions beyond thecontrol of the flooring manufacturer or the installationcontractor. If the concrete substrate deteriorates sufficiently, it willno longer support the bond of the remediation floorsystem.Such conditions are detailed in ACI 201.2R “Guide toDurable Concrete” published by the American ConcreteInstitute. See Crown Polymers Technical Bulletin: 1Concrete Surface Preparation.CHEMICAL RESISTANCE DATASee Crown Polymers Technical Bulletin: 9 ChemicalResistance Guidelines and Chart.CHECK CONCRETE MOISTUREConcrete must be dry before application of this floorcoating material. Concrete moisture tests are required,either ASTM F1869 (calcium chloride) or ASTM F2170(in situ RH probe). Refer to appropriate Technical DataSheet limits and Crown Polymers Technical Bulletin:6 Moisture Mitigation Negative Side Moisture Barrier.Physical Properties at 77 F (25 C)VOC (Volatile Organic Compounds), (VOC Calculated Per ASTM D3960)0 gr./lt.Pot Life,1 gallon (3.79 liters) Mass, Pot Life is Reduced by Increases in Mass & Temperature20 MinutesMix Ratio, by Volume1:1Minimum Application Surface Temperature50 FDry to Touch 50 F to 90 F (10 C to 32 F)2 to 4 HoursRecoat Time 50 F to 90 F (10 C to 32 F)12 to 24 HoursLight Traffic 50 F to 90 F (10 C to 32 F)72 HoursFull Cure 50 F to 90 F (10 C to 32 F)Shelf Life (shipped and stored) at 40 F to 100 F (4.4 C to 38 C)7 Days1.5 YearsPackaging 2 gal (7.57 lt.), 10 gal (37.9 lt.), and 100 gal (379 lt.)Mechanical Properties at 77 F (25 C) 7 Day Cure (Unless otherwise stated)Surface Preparation ICRI 310.2RConcrete Surface Profile (CSP 2 and above) Depending on System to be Installed and Condition of Concrete.Compressive Strength, ASTM D695, 7 Days12,000 PSITensile Strength, ASTM D6384,500 PSITensile Elongation, ASTM D6382%Adhesion, ASTM D7234, Concrete Failure 400 PSIHardness (Shore D) ASTM D224080-85Water Absorption, ASTM D570 Resin & Hardener0.15%Abrasion Resistance, ASTM D4060 Resin & Hardener500 cycles, Wheel No. CS17, 1000 gr. Load0.026 gr.Microbial (fungi) Resistance, ASTM G21 (Without the Anti-Microbial Agent)Pass #1Moisture Vapor Emission Rate, ASTM F1869*3 lbs.Relative Humidity, F2170*80%*If moisture or relative humidity exceeds the limits consult the Crown Polymers representative and refer to Crown Polymers Technical Bulletin: 6 Moisture Mitigation Negative Side Moisture Barrier.Note: Although testing is critical, it is not a guarantee against future problems. This is especially true if there is not apositive side vapor barrier or it is not functioning properly and/or concrete has contamination from oils, chemical spills,densifiers, excessive salts or other bond breakers.CP 7500 CrownPro AcidShield Novolar Epoxy Medium Viscosty TDS 20210223 DMPage: 2 of 5

CHEMICAL RESISTANCE CHARTThe chemical resistance of 7500 CrownPro AcidShield is influenced by many factors, including exposure to a mixture ofchemicals, service temperature, and housekeeping practices. 7500 CrownPro AcidShield Clear will have superior chemical and stain resistance to 7500 CrownPro AcidShield Pigmented. Successful engineering of the 7500 CrownPro AcidShield must also take into consideration such factors as substrate design, temperature cycling, and anticipated thermaland mechanical shock. Whenever possible, a sample should be tested under actual or simulated field conditions beforea decision is made on the suitability of a given system. Users are urged to consult Crown Polymers technical servicedepartment for recommendations on the specific project.The following chart is a guide to the resistance properties of 7500 CrownPro AcidShield.Key:1. Suitable for continuous contact for 7 days.2. Suitable for intermittent spills and continuous contact up to 72 hours3. Suitable for intermittent spills, when followed promptly by water flushing4. Not recommended* Coating stains when exposed to this chemicalAcetic Acid, 10%1Ethyl Acetate1Acetic Acid, 25%2Ethyl Alcohol1Acetic Acid, 50%3Formaldehyde1Acetic Acid, Glacial3Formic Acid 25%1Acetone2Gasoline1Aluminum Chloride1Hydrobromic Acid, 48%*1Aluminum Nitrate1Hydrochloric Acid, 37%*1Aluminum Sulfate1Hydrofluoric Acid, 25%2Ammonium Hydroxide1Hydrogen Peroxide, 30%1Ammonium Nitrate1Lactic Acid, 50%1Ammonium Sulfate1Lactic Acid, 85%1Aniline3Jet Fuel1Antifreeze (ethylene glycol or propylene glycol)1Isopropyl Alcohol1Barium Chloride1Maleic Acid, 40%2Barium Hydroxide1Methanol1Barium Sulfide1Methylene Chloride3Beer1MEK (Methyl Ethyl Ketone)2Benzene1Mineral Spirits1Betadine*1Motor Oil1Boric Acid1Mustard1Brake Fluid1Nitric Acid, 10%*1N-Butyric Acid, 50%3Nitric Acid, 30%*2Calcium Chloride1Nitric Acid, 50%*3Calcium Hydroxide1Oleic Acid1Calcium Nitrate1Phosphoric Acid, 85%2Calcium Sulfate1Potassium Chloride1Chloroform1Potassium Cyanide1CP 7500 CrownPro AcidShield Novolar Epoxy Medium Viscosty TDS 20210223 DMPage: 3 of 5

Citric Acid, 50%1Potassium Nitrate1Coffee1Potassium Sulfate1Cola Syrup1SkydrolCopper Chloride1Sodium Hydroxide, 50%1Copper Nitrate1Sodium Chloride1Diesel Fuel1Sulphuric Acid, 50%DILUTED per ECOLABS RECOMMENDATIONSSulphuric Acid, 98%*1*1*1 Boost 3200 Diluted 12 fl. oz. per Gal Water2Tetrahydrofuran3 Boost 3201 Dilute 12 f. oz. per Gal Water2Toluene1 Exelerate HS Diluted 1 fl. oz. per Gal Water2Transmission Fluid1 Konduct Alkaline Cleaner Na2O 12.3%2Trichlorethylene3 Mandate Plus Diluted 1 fl.oz. per 3 Gal Water2Trichloroethylene1 Passivation Acid Diluted 50% Water2Urea1 Ster-Bac Quat Diluted 1 fl. oz. per 2.5 Gal Water3Vegetable Oil1 Synerge Diluted 1 fl. oz. per 4 Gal Water2Whiskey1 VORTEXX Diluted 6 fl. oz. per Gal Water2Xylene1 XY-12 Diluted 12 fl. oz. per Gal Water2CHECK TEMPERATURE & HUMIDITYThe concrete must be dry before application of this floorcoating material. Concrete moisture tests are required,either ASTM F1869 (calcium chloride) or ASTM F2170(in situ RH probe). Refer to appropriate Technical DataSheet limits and Crown Polymers Technical Bulletin: 6Moisture Mitigation Negative Side Moisture Barrier.CHECK TEMPERATURE & HUMIDITYFloor and material temperature must be at or above thepublished Technical Data Sheet. Dew Point must be 5 F(3 F) or more below the surface temperature. Do not applyif humidity is at or above 95%. See Crown PolymersTechnical Bulletin: 7 Temperature and Relative HumidityLimits.SURFACE PREPARATIONSurface preparation per: ICRI Guideline No. 310.2RSelecting and Specifying Concrete Surface Preparationfor Sealers, Coatings, Polymer Overlays, and ConcreteRepair. The pH of the concrete substrate should be at 9 orabove. All bond-breaking material must be removed. SeeCrown Polymers Technical Bulletin: 1 Concrete SurfacePreparation.APPLICATION EQUIPMENTDepending on system applied: Disposable 3” brush forcutting in, variable low-speed drill (450 rpm) with Jiffy type impeller mixing paddle, 3/8 inch nap non-sheddingphenolic core roller, and V-notched rubber squeegee forspreading neat epoxy and gauge rake or trowels forthicker applications.OPTIONAL ANTIMICROBIALThe antimicrobial additive is a non-heavy metal biocidethat can be added during the manufacturing process.The antimicrobial agent can be added to the topcoat onlyfor an economical application or it can be added to eachstep of the application, primer, body coat, and topcoat,which is recommended for abusive environments. SeeCrown Polymers Technical Bulletin: 11 Understandingthe Optional Antimicrobial Additive.MIXINGFor ease of mixing and placement, the temperature ofthe “A” and “B” components should be between 70 F to80 F (20 C to 26 C). Pre-mix the “A” and “B” componentsto ensure all raw material and pigments are disperseduniformly. See Crown Polymers Technical Bulletin: 10Mixing Guidelines.APPLICATIONAfter mixing all contents as instructed, immediately pourall liquid material onto the properly prepared concretesubstrate, or next epoxy lift in ribbons and squeegeethe material out evenly. Back-rolling and cross rolling ofmaterial are critical for receiving coat, lock coat, groutcoat, topcoat, and finish coat. Check for desired wet filmthickness with a WFT Gauge. If broadcasting aggregate,CP 7500 CrownPro AcidShield Novolar Epoxy Medium Viscosty TDS 20210223 DMPage: 4 of 5

broadcast into the wet material. Place trowel mortar mixwithin installation sequence. Place all steps per CrownPolymer Installation Guidelines.DISPOSALDispose of empty packaging and other waste per federal,state, province, and local regulations.SKID-RESISTANCESkid-Resistance – Field (in situ) Wet Dynamic Coefficientof Friction (DCOF), ANSI A326.3. See Crown PolymersTechnical Bulletin: 4 Coefficient of Friction.MAINTENANCEInspect the installed floor by spot cleaning and spotrepairing the damaged or cracked areas. To prolong thelife of the flooring system, a daily maintenance programis highly recommended to ensure the floor is safe for itsintended purposes. See Crown Polymers TechnicalBulletin: 8 Care and Maintenance.SHIPPING and STORAGEShip and store material between 40 F to 90 F (4 C to 32 C).Store in a dry environment and out of direct sunlight.SHELF LIFEShelf life is 1 year from the date of manufacture, providedthe containers are unopened.CLEAN-UPClean-up mixing station, tools, and equipment as required.Use acetone, a VOC exempt solvent, for cleaning up.Observe all legal, and health, and safety precautions whenhandling or storing solvents and materials, particularly inconfined spaces. Make sure the working areas are wellventilated at all times during placement and curing time.TECHNICAL SUPPORTFor questions, contact a Crown Polymers Representative.Additional Support Documents are available from CrownPolymers, including brochures, application guidelines,videos and more. Visit Crownpolymers.com or contactCrown for additional resources.DISCLAIMERAll guidelines, recommendations, statements, and technical data contained herein are based on information and tests. The accuracy and completeness of such tests are not guaranteed and are notto be construed as a warranty, expressed or implied. It is the responsibility of the user to document information and tests to determine the intent of the product for ones’ own use. The application,job conditions and user assumes all risks and liability resulting from use of the product. We do not suggest or guarantee any hazards listed herein are the only ones, which may exist. Neither sellernor manufacturer shall be liable to the buyer or any third person for any injury, loss or damage directly or indirectly resulting from use of, or inability to use the product. Recommendations or statements, whether in written or verbal, other than those contained herein shall not be binding upon the manufacturer, unless in writing and signed by a corporate officer of the manufacturer. Technicaland application information is provided for the purpose of establishing a general profile of the material and proper application procedures. Test performance results were obtained in a controlledenvironment and Crown Polymers makes no claim that these tests or any other tests accurately represent all environments. Not responsible for any typographical errors.LIMITED WARRANTYCrown Polymers warrants its products to be free of manufacturing defects and meets all Crown Polymers current published physical properties. Crown Polymers’ sole responsibility shall be toreplace the portion of any product proved to be defective. There are no other warranties by Crown Polymers of any nature whatsoever expressed or implied, including any warranty of merchantability or fitness for a particular purpose in connection with this product. Crown Polymers shall not be liable for damages of any sort, including remote or consequential damages resulting from anyclaimed breach of any warranty whether expressed or implied. Crown Polymers shall not be responsible for the use of this product in a manner to infringe on any patent held by others. In addition, nowarranty or guarantee pertaining to appearance, color, fading, chalking, staining, shrinkage, peeling, normal wear and tear or improper application by the applicator will be issued. Damage causedby abuse, neglect and lack of proper maintenance, acts of nature and/or physical movement of the substrate or structural defects are also excluded from the limited warranty. Crown Polymersreserves the right to conduct performance tests on any material claimed to be defective prior to any repairs by owner, general contractor, or applicator.Crown Polymers Corp. Tel: 847.659.0300 Fax: 847.659.0310info@crownpolymers.com www.crownpolymers.com 2020 Crown Polymers Corp. All rights reservedCP 7500 CrownPro AcidShield Novolar Epoxy Medium Viscosty TDS 20210223 DMPage: 5 of 5

Concrete Surface Profile (CSP 2 and above) Depending on System to be Installed and Condition of Concrete. . ical and stain resistance to 7500 CrownPro AcidShield Pigmented. Successful engineering of the 7500 CrownPro Acid- . Coffee 1 Potassium Sulfate 1 Cola Syrup 1 Skydrol * 1 Copper Chloride 1 Sodi

Related Documents:

Concrete Surface Profile (CSP 2 and above) Depending on System to be Installed and Condition of Concrete. . chemical and stain resistance to 7350 CrownPro AcidShield Pigmented. Successful engineering of the 7350 CrownPro . Coffee 1 Potassium Sulfate 1 Cola Syrup 1 Skydrol * 1

CrownFlex Membrane (0-50 g/L) CrownPro AcidShield (0-50 g/L) CrownPro EPC TempShield (0-50 g/L) . H&C Shield Crete Epoxy Concrete Garage Floor Coating (50-250 g/L) InternationalCoatingsInc. . Miracote, Sinak, Floric Concr

Contents 3 Epoxy resins, water-reducible 4 Epoxy hardeners, water-reducible 5 Epoxy resins solid and solutions 6 Epoxy resins liquid and reactive diluted 7 Reactive diluents for epoxy resins 7 Epoxy hardeners, polyamines 8 Epoxy hardeners, adducts 9 Epoxy hardeners, mannich bases 10 Epoxy hardeners, polyamidoamines 11 Survey of the qu

Tile-Clad HS Epoxy : Water-Based Tile-Clad Pro Industrial High Performance Epoxy : Epolon II Multi-Mil Epoxy Macropoxy HS Epoxy : Macropoxy 646 Fast Cure Epoxy High Solids Catalyzed Epoxy : Macropoxy 846 Winter Grade Epoxy Sher

mechanical properties of epoxy resins, physical and chemical properties of epoxy resins, epoxy resin adhesives, epoxy resin coatings, epoxy coating give into water, electrical and electronic applications, analysis of epoxides and epoxy resins and the toxicology of epoxy resins. It will be a standard reference book for professionals and .

2 Applied Biosystems 7300/7500/7500 Fast Real-Time PCR S ystem Relative Quantification Getting Started Guide Notes About the 7300/7500/7500 Fast System Description The Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System uses fluorescent-based PCR chemistries to prov ide quantitative detection of nu cleic acid sequences using

0811-7500-1, 0811-7500-2, 0811-7500-3 The following instructions provide the necessary information for the proper operation and preventive maintenance of the Binks Airless 75 Spray Gun. Please read and understand all information in this document in order to get the maximum performance from your new Airless 75 spray gun. IMPORTANT!

In recent years, there has been an increasing amount of literature on . A large and growing body of literature has investigated . In recent years, several studies have focused on