Service Manual - W11169659 - Whirlpool & Maytag 27' Front .

2y ago
15 Views
2 Downloads
7.44 MB
80 Pages
Last View : 22d ago
Last Download : 2m ago
Upload by : Ophelia Arruda
Transcription

L-98SERVICE MANUALWHIRLPOOL & MAYTAG27” FRONT-LOADGAS & ELECTRIC DRYERSW11169659

FORWARDThis Whirlpool Service Manual, (Part No. W11169659), provides the In-Home Service Professional withservice information for the “WHIRLPOOL & MAYTAG 27” FRONT-LOAD GAS & ELECTRIC DRYERS.”The Wiring Diagram used in this Service Manual is typical and should be used for training purposesonly. Always use the Wiring Diagram supplied with the product when servicing the dryer.For specific operating and installation information on the model being serviced, refer to the “Use andCare Guide” or “Installation Instructions” provided with the dryer.GOALS AND OBJECTIVESThe goal of this Service Manual is to provide information that will enable the In-Home ServiceProfessional to properly diagnose malfunctions and repair the “WHIRLPOOL & MAYTAG FRONT-LOADDRYERS.”The objectives of this Service Manual are to: Understand and follow proper safety precautions. Successfully troubleshoot and diagnose malfunctions. Successfully perform necessary repairs. Successfully return the dryer to its proper operational status.WHIRLPOOL CORPORATION assumes no responsibility for any repairs made on ourproducts by anyone other than authorized In-Home Service Professionals.Copyright 2019, Whirlpool Corporation, Benton Harbor, MI 49022ii n Whirlpool & Maytag Front-Load Dryers

TABLE OF CONTENTSWHIRLPOOL & MAYTAG FRONT-LOAD DRYERSSECTION 1 — GENERAL INFORMATIONDRYER SAFETY.1-2WHIRLPOOL CONTROL PANEL & FEATURES (HMI IN DOOR).1-3WHIRLPOOL CONTROL PANEL & FEATURES (CONSOLE).1-4MAYTAG CONTROL PANEL & FEATURES (CONSOLE).1-6MODEL & SERIAL NUMBER LABEL LOCATION.1-8WIRING DIAGRAM LOCATION.1-8MODEL AND SERIAL NUMBER NOMENCLATURE.1-9PRODUCT SPECIFICATIONS.1-10SECTION 2 — DIAGNOSTICS & TROUBLESHOOTINGWHIRLPOOL & MAYTAG DIAGNOSTICS (CONSOLE MODELS).2-2WHIRLPOOL/AMANA/INGLIS CONTROL PANEL.2-2MAYTAG CONTROL PANEL.2-3ABBREVIATIONS.2-4DIAGNOSTIC GUIDE.2-4SERVICE DIAGNOSTIC MODE.2-4ACTIVATING SERVICE DIAGNOSTIC MODE.2-4SERVICE DIAGNOSTIC MENU TABLE.2-4KEY ACTIVATION & ENCODER TEST.2-5SERVICE TEST MODE.2-5SERVICE TEST MODE CHART.2-5SOFTWARE VERSION DISPLAY.2-7FAULT/ERROR CODES.2-7EXITING SERVICE DIAGNOSTIC MODE.2-7WHIRLPOOL DIAGNOSTICS (LCD IN DOOR MODELS).2-8ABBREVIATIONS.2-8DIAGNOSTIC GUIDE.2-8SERVICE DIAGNOSTIC MODE.2-8ACTIVATING SERVICE DIAGNOSTIC MODE.2-8SERVICE DIAGNOSTIC MODE TESTS.2-9COMPONENT ACTIVATION.2-10SERVICE TEST MODE.2-10SERVICE FAULT/ERROR CODES CHART.2-11CUSTOMER DIAGNOSTIC CODES CHART.2-11TROUBLESHOOTING GUIDE.2-12VOLTAGE TO HEXADECIMAL CODES.2-14SECTION 3 — COMPONENT TESTINGCOMPONENT TESTING: SAFETY INFORMATION.3-2COMPONENT LOCATIONS.3-3WIRING DIAGRAM - WHIRLPOOL, ELECTRIC.3-4WIRING DIAGRAM - WHIRLPOOL, GAS.3-5WIRING DIAGRAM - MAYTAG, ELECTRIC.3-6WIRING DIAGRAM - MAYTAG, GAS.3-7COMPONENT TESTING.3-8TEST #1: ACU POWER CHECK.3-8ACU BOARD / CONNECTORS & PINOUTS.3-9TEST #2: SUPPLY CONNECTIONS.3-10TEST #3: MOTOR CIRCUIT.3-12TEST #4: HEAT SYSTEM.3-14TEST #4A: THERMISTORS.3-16Whirlpool & Maytag Front-Load Dryers n iii

TABLE OF CONTENTSWHIRLPOOL & MAYTAG FRONT-LOAD DRYERSTEST #4B: THERMAL FUSE.3-17TEST #4C: THERMAL CUTOFF.3-17TEST #4D: GAS VALVE.3-18TEST #5: MOISTURE SENSOR.3-19TEST #6: BUTTONS AND INDICATORS.3-20TEST #7: DOOR SWITCH.3-21TEST #8: DRUM LED.3-22TEST #9: WATER VALVE.3-23SECTION 4 — COMPONENT ACCESSCOMPONENT LOCATIONS.4-2DOOR REVERSAL — ROUND SHAPED DOORS.4-3DOOR REVERSAL — SQUARE SHAPED DOORS.4-7REMOVING THE TOP PANEL.4-9REMOVING THE CONSOLE/HMI.4-9REMOVING THE APPLIANCE CONTROL UNIT (ACU).4.10REMOVING THE FRONT PANEL & DOOR SWITCH.4-11REMOVING THE DRUM LIGHT.4-12REMOVING THE MOISTURE SENSOR.4-12REMOVING THE BELT, DRUM, AND ROLLERS.4-13REMOVING THE DRIVE MOTOR.4-15REMOVING THE THERMAL FUSE & OUTLET THERMISTOR.4-16REMOVING THE HEATER ELEMENT.4-17REMOVING THE HIGH LIMIT THERMOSTAT & THERMAL CUTOFF.4-17REMOVING THE IGNITOR, FLAME SENSOR (GAS).4-18REMOVING THE HIGH-LIMIT THERMOSTAT & THERMAL CUTOFF (GAS).4-19REMOVING THE GAS BURNER ASSEMBLY COILS (GAS).4-20REMOVING THE REAR PANEL.4-21REMOVING THE WATER VALVE.4-22SECTION 5 — CONNECTIVITYINTERNET CONNECTIVITY GUIDE.5-2INITIAL SETUP.5-2DOWNLOAD AND INSTALL WITH TOUCH SCREEN.5-2DOWNLOAD AND INSTALL WITH NON-TOUCH SCREEN.5-2CONNECTION STATUS.5-3TROUBLESHOOTING GUIDE.5-3PRODUCT SPECIFICATIONS & WARRANTY INFORMATION SOURCES (inside back cover)iv n Whirlpool & Maytag Front-Load Dryers

GENERAL INFORMATIONSection 1:General InformationThis section provides general safety, parts, and information forthe “Whirlpool & Maytag Front-Load Gas & Electric Dryers.” Dryer Safety Whirlpool Control Panel & Features (HMI in Door) Whirlpool Control Panel & Features (Console) Maytag Control Panel & Features (Console) Model/Serial Number Location Wiring Diagram Location Model & Serial Number Nomenclature Product SpecificationsWhirlpool & Maytag Front-Load Dryers n 1-1

GENERAL INFORMATIONDryer SafetyYour safety and the safety of others are very important.We have provided many important safety messages in this manual and on your appliance. Always read and obey all safetymessages.This is the safety alert symbol.This symbol alerts you to potential hazards that can kill or hurt you and others.All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”These words mean:DANGERWARNINGYou can be killed or seriously injured if you don't immediatelyfollow instructions.You can be killed or seriously injured if you don't followinstructions.All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what canhappen if the instructions are not followed.1-2 n Whirlpool & Maytag Front-Load Dryers

GENERAL INFORMATIONCONTROL PANEL AND FEATURESWhirlpool Control Panel & Features (HMI in Door)Not all features and cycles are available on all models.NOTE:controlpanelfeaturesa sensitivesurfacethat responds to a light touch of your finger. To ensure your selections areNot allThefeaturesandcyclesare availableon allmodels.registered, touch the control panel with your fingertip, not your fingernail. When selecting a setting or option, simply touch theNOTE: The button.control panel features a sensitive surface that responds to a light touch of your finger. To ensure your selections areappropriateregistered, touch the control panel with your fingertip, not your fingernail. When selecting a setting or option, simply touch theappropriate button.52.4:28What to DryREGULARTemperatureLOW0:45How to DryNORMALSet Auto-Drying L.NORMALWrinkle ShieldOFF11. Use Tools button to change13other6settings,7 if desired41 POWER/CANCEL BUTTONToolsTouch to turn the dryer on or off or to a cancel a cycle.2 HOME BUTTON1 POWER/CANCEL BUTTONTouch this button and the LCD screen will show the homeTouchturn theon or youroff orcycle,to a cancelcycle.screen,towhereyoudryercan selectsettings,a andoptions.2 HOME BUTTONFAVORITESBUTTON3 Touchthis buttonand the LCD screen will show theStoresandaccessesyourcanfavoriteand alsoaccesseshome screen, where youselectcycles,your cycle,settings,a historyof recently run cycles.andoptions.3 FAVORITES4 LCD SCREEN BUTTONStores and accesses your favorite cycles, and alsoUse this screento selectcycle,settings,accessesa historyof recentlyruncycles. options, etc.4Swiping the screen gives access to five frequently runcycles.SCREENLCDUse this screen to select cycle, settings, options, etc.REMOTEtheENABLE5 SwipingscreenBUTTONgives access to five frequently runcycles.Download the Whirlpool app and follow the instructionsto connect your dryer to your home Wi-Fi network. Youmay also visit www.whirlpool.com/connect. In Canada,visit www.whirlpool.ca/connect. After having connectedto Wi-Fi, press the REMOTE ENABLE button any time youwant to use the app. Pressing this button locks out theLCD screen and you will be prompted with a messageabout the dryer waiting for input from the app. To exit thismode, press the REMOTE ENABLE button again.6 TOOLS BUTTONTouch this button to access the Tools screen.7 START/PAUSE BUTTONTouch and hold to start, or touch to pause a cycle. Whenthe dryer drum begins to move, release the START/PAUSEbutton. Continuing to hold the Start/Pause button afterthe dryer has started will cause the dryer to stop.6 -XO ('7 5(/( 6('125REMOTE ENABLE BUTTONDownload the Whirlpool app and follow the instructionsto connect your dryer to your home Wi-Fi network. YouThe Toolsgivesaccess to many other settings,utilitymaybuttonalso visitwww.whirlpool.com/connect.In uttonTheToolsbuttongivesaccessto many ersettings,havingconnectedto accessthe Toolswhich containsthefollowing(youcycles,andTouch theTOOLStopreferences,Wi-Fi,pressscreen,the information.REMOTEENABLEbuttonany ingertotheaccessof se theapp.Pressingthis buttonlocksalloutselections).(youwillneedto scrollwithfinger withto accessLCDscreenand downyou willbeyourprompteda message aboutallof theLockselections).Controlthe dryer waiting for input from the app. To exit this mode, thetoPress &thislock thecontrols.buttonSwipeagain.up to unlock.pressREMOTELoadGoiconDispenser1 ENABLEMute this icon to access:Press76 TOOLSBUTTON StatusDispenser1 andsounds.choose between:LoadGoiconPress &thistobuttonmuteorunmuteTouchthisto access the Tools screen. For more ActiveUtilityinformation,Cycle(1 Cycle)see page 11. DisabledPressicon to access utility cycles: Rinse, Spin, Drain, Clean Cycle.Offthis(Permanently) 7 r 1 and choose between:DetergentTouch and hold to start, or touch to pause a cycle. When2X SelecttheSteamRefreshtoreduceodorsreleaseand lightindryer drum beginsto move,thewrinklesSTART/PAUSE dry4Xloadsconsistingof ngtoholdtheStart/Pausebuttonafter6X blends, common knits, and synthetics. If you will be unable the8X dryerahas startedwill causethe dryerto stop.to removeloadimmediately,touchWRINKLESHIELD to addup to &150of periodictumbling. You may select the LoadGominutesDispenser2Steam setting to add a short steam cycle after 60 minutes toPressthisicontoaccess:help smooth out wrinkles.Load & Go Status Dispenser 2 and choose between:PreferencesActive Pressto accessTimes and Dates, Sound Volume, DisplayDisabled(1 Cycle) Settings,and Regional. Follow the screen prompts.Off (Permanently) LoadWiFi & Go Content Dispenser 2 and choose between:Softener Pressto access Connect to Network, SAID Codes, Mac Address, Detergentand WiFi. Follow the screen prompts.Once set at Detergent:InfoSet Concentration Dispenser 2 and choose between:Press2X to access Service & Support, Store Demo Mode, Restore Factory,4X WiFi Terms and Conditions, and Software Terms and Conditions.Follow the screen prompts.6X 8XWhirlpool & Maytag Front-Load Dryers n 1-3TouchTo pauonce,cycle,estimaOnce ythe doduring1314After agarmeControl Lock,Q VRPH (XURSHDQ IDFWRULHV WKH OHWWHU : RI WKH SDUW FRGH PHQWLRQHG KHUHLQ ZLOO EH DXWRPDWLFDOO\avoid SODFHG E\ WKH QXPEHU H J : EHFRPHV Mutegarmeback t

GENERAL INFORMATIONControlPanel & Features (Console)CONTROLWhirlpoolPANEL ANDFEATURESNot all features and cycles are available on all models.NOTE: The control panel features a sensitive surface that responds to a light touch of your finger. To ensure your selections areregistered, touch the control panel with your fingertip, not your fingernail. When selecting a setting or option, simply touch theappropriate button.STEAM MODELS1236454NON-STEAM MODELS123564541POWER2WHAT TO DRY/HOW TO DRYMore Time/Less Time Timed Dry AdjustTouch MORE TIME or LESS TIME with the Timed Dry/Quick cycle to increase or decrease the length of thecycle.Touch to turn the dryer on and off. Touch to stop/cancela cycle at any time.Once a “What to Dry” is selected, the dryer automaticallyselects the recommended or last-used “How to Dry”option, as well as the recommended/last-used modifiers.Both the “How to Dry” and modifiers can be changed ifdesired. See the “Cycle Guide” for details.3START/PAUSE4MODIFIERSTouch and hold until LED counts down “3-2-1” and thedryer starts; then let go to start a cycle, or touch oncewhile a cycle is in process to pause it.Use to select available modifiers for your dryer. Not allcycles and options are available on all models.TempWhen using Timed Dry/Quick Cycle, you may selecta dry temperature based on the type of load you aredrying. Use the warmest setting that is safe for thegarments in the load. Follow garment label instructions.NOTE: Automatic Cycles will give you up to fourtemperatures to adjust, depending on the model andthe “What to Dry” or “How to Dry” selections that havebeen made.DrynessYou may adjust the Dryness on Automatic Cycles(except for the Sanitize cycle), if desired.NOTE: Dryness is for use with Automatic Cycles only.55OPTIONSUse to select available options for your dryer. Not allcycles and options are available on all models.Wrinkle Shield OptionIf you will be unable to remove a load immediately,touch WRINKLE SHIELD to add up to 150 minutesof periodic tumbling to help reduce wrinkling. Youmay select the “ Steam” setting (on some models)to add a short steam cycle after 60 minutes to helpsmooth out wrinkles.NOTE: If you open the dryer door prior to the endof the Wrinkle Shield option, the dryer will go intostandby.Steam Refresh (steam models only)This cycle is best for reducing wrinkles and odorsfrom dry items. Cycle time will increase, dependingon number of items. This is an independent cycle thatcannot be combined with any other cycle.Cycle SignalUse this option to turn the signal indicating the endof a drying cycle to low, medium, high, or off. Thevolume you select here will also be applied to theDamp Dry Signal.NOTE: You may also turn off the tones that soundwhen a feature, setting, or option is touched. Touchand hold CYCLE SIGNAL for about 3 seconds to turnsounds to low, medium, high, or off.61-4n Whirlpool & Maytag Front-Load Dryers,Q VRPH (XURSHDQ IDFWRULHV WKH OHWWHU : RI WKH SDUW FRGH PHQWLRQHG KHUHLQ ZLOO EH DXWRPDWLFDOO\ -XO ('7 5(/( 6('UHSODFHG E\ WKH QXPEHU H J : EHFRPHV

Appearance may vary.GENERAL INFORMATIONThe Cycle Status Indicators show the progress of a cycle.Whirlpool Control Panel & Features(Console)continuedNot all indicatorsare available onall models.66WetSensingDamp Dry SignalTheSensingload is indicatorstill wet and/ortheperiodicallycycle just started.Thewill lightduring SensorTouch to turn the Damp Dry Signal on or off. WhenCycles to indicate that the moisture sensor on the dryer isselected, a series of beeps will sound when the loadDampoperating. This indicator will not light during Timed Cyclesis damp, but not completely dry. This will allow you toindicatorthat Shield .the load is partially dried andorThisoptionssuch showsas Wrinkletake clothes out of the load that do not need to dryitems that you may wish to hang up or iron while stillcompletely. This option is available on some cycles.damp may be removed.WetDampDry SignalThe DampDry signal is selected as a default for theTheload is still wet and/or the cycle just started.TouchtoturntheDampDrySignalonoroff.When,Q VRPH (XURSHDQ IDFWRULHVBulky Items/Normal, Bulky Items/Wrinkle Control,Cool Downselected,a seriesof beepswill cycles,sound whenthe load -XO ('7 5(/( 6('UHSODFHand BulkyItems/HeavyDutyas a reminderThedryer has finished drying with heat and is nowDampis todamp,but notcompletelydry.Thismidwaywill allowyou owsload withoutheattoiscoolit theclothescycle. out of the load that do not need to dryitems that you may wish to hang up or iron while stillcompletely. This option is available on some cycles.Check Ventdamp may be removed.ReduceStatic(onsomemodels)The Damp Dry signal is selected as a default for theThe Check Vent indicator is a feature available forTouchto add the ReduceStatic option toControl,selectedBulkyItems/Normal,Bulky Items/WrinkleAutomaticCoolDown cycles only. This indicator will show the statusAutomaticcycles. The Dutydryercycles,will automaticallytumble,andBulky Items/Heavyas a reminderof airflowthroughthedryingdryer andsystemThedryer hasfinishedwith theheatdryerand ventis nowandrepositionintroducebulkya smallamountof moisturetopause,manuallyloadsmidwaythroughfor the dryer’slife.Duringheatthe tosensingtumblingthe loadwithoutcool itphasedown.at theintothe load to help reduce static. This option addsthecycle.beginning of the cycle, the Check Vent light will come onCheckVent vent or low airflow issue is detected. This lightapproximately 3 minutes to the total cycle time.if a blockedReduce Static (on some models)TheCheckVenta featureavailablefor Ventwillstayonfor indicatorthe entireiscycle.Shouldthe CheckControlLockTouchto addthe Reduce Static option to selectedAutomaticcycles referonly. toThisindicatorwill show ectionUse this optionlockthe willcontrolsof the ,offorairflowthroughthe dryerandissue.the dryer vent systempotentialsolutionsto theandavoidanaccidentalchangeincycleoptionspause, and introduce a small amount of moisturefor the dryer’s life. During the sensing phase at theThe light ofwillbecycle,clearedcompletionthecycle,or thepreferencesduringa dryingcycle.intoload to helpreducestatic.This option addsbeginningthetheuponCheckVent eCheckVentlightlightapproximately 3 minutes to the total cycle sTouch and hold CONTROL LOCK or DAMP DRYwillcontinuetoilluminateduringthe cycleunlessVentthe AL(depending on the model) for 3 seconds toControlLockcauseis resolved.lightilluminate,refer to the “Troubleshooting” sectionlockor optionunlocktothecontrolsof the dryer.Usethislockthe controlsof the Duringdryer thisREMEMBER:The dryerwillissue.continue to operate evenforpotentialsolutionsto thetime,theLEDDisplaywillcountdown“3-2-1.”and avoid an accidental change in cycle optionswhiletheindicatorislit,butpoorairflow ofcanthe controlsarelocked,cycle.the LED DisplayThe light will be cleared upon completiontheimpactcycle, dryorOncepreferencesduringa dryingtimes andoverallFor moreinformationonwill display “Loc.”touchingPower,or performance.opening the door.The CheckVent lightmaintaininggoodairflow,duringsee “CheckYourVent theSystemTouch and hold CONTROL LOCK or DAMP DRYwillcontinue toilluminatethe cycleunlessrootfor GoodAirflow.”NOTE: (dependingThe ControlonLockmaybe enabledSIGNALthe functionmodel) for3 secondstocauseis resolved.whenrecoveringfrom a powerTo unlocklockor unlockthe controlsof thefailure.dryer. uestoduringa cycle,REMEMBER: Thecontinueoperateevencontrol,touchand holdor DAMPtime,the LEDDisplaywill CONTROLcount downLOCK“3-2-1.”the CheckVent indicatorwillnotairflowlight up.Seethe GNAL(dependingon thethe LEDmodel)for at leastOncecontrolsare locked,Display“Troubleshooting”section.times and overall performance. For more information on3 seconds.willdisplay “Loc.”maintaininggood airflow, see “Check Your Vent SystemEndOptionEcoBoost forThisGoodNOTE:The ControlLock function may be enabledwillAirflow.”indicate that the selected cycle has endedThe recoveringEcoBoost fromoptionwill defaultfor thewhena powerfailure.onToonlyunlocktheand theload maybe removedfromduringthe dryer.If WrinkleNOTE:If thereare othererror issuesa cycle,Regular/Normaland is only LOCKavailableon thatcontrol,touch andcyclehold CONTROLor DAMPShield selected,thelightdryertotheCheck hasVentbeenindicatorwill notup.maySeecontinuethecycle.This thetomodel)for yourat leasttumble the load, section.even if “End” is displayed.“Troubleshooting”3 savingsseconds.by using a slightly lower heat level. TheControl LockEcoBoost option will increase drying times byEndOptionEcoBoost Thiswillilluminatethe controlsarelocked.approximately40 minutes, which will be reflectedThiswillindicatethatoncethe selectedcyclehasendedTheoptionwill defaultfor theon EcoBoost the LED Display.If optimaltimeonisonlydesired,touchand the load may be removed from the dryer. If WrinkleRegular/Normalandthisis onlyavailable on thatECOBOOST tocycleturn offoption.Shield has been selected, the dryer may continue tocycle. This option allows you to increase your energytumble the load, even if “End” is displayed.savings by using a slightly lower heat level. TheLEDDISPLAYControl LockEcoBoost option will increase drying times byWhenyou select aits defaultwill light upThis will illuminate once the controls are locked.approximately40cycle,minutes,which settingswill be reflectedandTimeIf Remaining(forCycles)onthetheEstimatedLED Display.optimal timeis Automaticdesired, touchwillECOBOOSTvary dependingon off“WhatDry” and “How to Dry”to turnthis tooption.selections, or actual time remaining for Timed Dry cycles(for Manual Cycles) will be displayed.LED DISPLAYWhen you select a cycle, its default settings will light upCYCLESTATUSINDICATORSandthe EstimatedTimeRemaining (for Automatic Cycles)will vary depending on “What to Dry” and “How to Dry”selections, or actual time remaining for Timed Dry cycles(for Manual Cycles) will be displayed.CYCLE STATUS INDICATORSAppearance may vary.The Cycle Status Indicators show the progress of a cycle.Not all indicatorsare availableall models.Appearancemayonvary.SensingThe Sensing indicator will light periodically during SensorCycles to indicate that the moisture sensor on the dryer isoperating.This indicatornot thelightprogressduring TimedCyclesTheCycle StatusIndicatorswillshowof a cycle.or alloptionssuch areas WrinkleNotindicatorsavailableShield .on all models.SensingWhirlpool & Maytag Fron

This washer/dryer has a tight seal to avoid water leaks. To avoid odors, leave the door open to allow the washer/dryer to dry between uses. If a dry cycle is interrupted and the load removed before the cool-down period at the end of the cycle, the load will be very hot.

Related Documents:

Whirlpool & Maytag Direct Drive Top Load Washer. FORWARD . This Whirlpool Service Manual, (Part No. W10864849), provides the In-Home Service Professional with service information for the "WHIRLPOOL & MAYTAG 6.2 CU. FT. DIRECT DRIVE TOP LOAD WASHER." The Wiring Diagram used in this Service Manual is typical and should be used for training .

www.whirlpool.com or www.whirlpool.ca HOTTE DE CUISINIÈRE CONFIGURÉE EN ÎLOT À MONTAGE MURAL 30" (76,2 CM) ET 36" (91,4 CM) Instructions d’installation et Gu ide d’utilisation et d’entretien Au Canada, pour assistance, installation ou service composez le 1-800-807-6777 ou visitez notre site web à www.whirlpool.ca

www.whirlpool.com or www.whirlpool.ca LAVADORA AUTOMÁTICA CABRIO Manual de Uso y Cuidado Si tiene preguntas respecto a las características, funcionamiento, rendimiento, partes, accesorios o servicio técnico, llame al: 1-800-253-1301 En Canadá, llame al: 1-800-807-6777 o visite nuestro sitio web en www.whirlpool.com o www.whirlpool.ca LAVEUSE

Whirlpool Electric Range Whirlpool Electric Range THANK YOU for purchasing this high-quality product. Register your range at www.whirlpool.com. For future reference, please make a note of your product model and serial numbers. These can be found on the label located on the upper-right corner of the front frame. RANGE SAFETY

W11218737B French Door Bottom Mount Refrigerator Use & Care Guide www.maytag.com U.S.: 1-800-688-9900 www.maytag.ca Canada: 1-800-807-6777

This Maytag Heritage Job Aid, “Failure Codes And Wiring Diagrams For Gas & Electric Ranges,” (Part No. 8178713), provides the technician with information on Diagnosing and Troubleshoot-ing Maytag Heritage Gas & Electric Ran

www.whirlpool.fr Whirlpool France SAS - 2 rue Benoît Malon - BP300 - 92156 Suresnes Cedex *le sens de la différence rcs 325041 481 cuisinez 3 fois plus rapidement Grâce à Whirlpool, l’expert de la cuisson au micro-ondes ! idées recettes et astuces

Send comments (with copy to psa@ansi.org) to: Christina Earl, (315) 339-6937, cearl@esda.org TCIA (ASC A300) (Tree Care Industry Association) Revision BSR A300 (Part 3)-201x, Tree Care Operations - Tree, Shrub, and Other Woody Plant Management - Standard Practices (Supplemental Support Systems) (revision of ANSI A300 (Part 3)-2006)