Installation Instructions RACO Freestanding Classic .
·.-::. .Installation instructions RACO Freestanding Classic aluminum door framesFreestanding frames install ceiling height or less than ceiling height.Specify regular studs fors/a"gypsum board; specify "shim" studs for1f2" board.Freestanding "separate studs" frames(Gyp-board screws concealed)Freestanding"FASTRAK " frames(Gyp-board screws outside jambs)RACO parts list (Separate studs)RACO parts list (FASTRAK studs)1111011 FS-1 door header with clips installed1 FS-2F hinge jamb assembly with stud segments andstop installed1 FS-3F strike jamb assembly with studs segments andstop installed2 R-4 speed screws1 R-46 strike clip with screws and washersFS-1 door header with clips installedFS-2S hinge jamb & FS-3S strike jambpair R-3A aluminum studsR-4 speed screws and 2 snap-on stopsR-46 strike clip with screws and washersRough opening Door opening width 1V4", dooropening height 1/2". Hold drywall stud back 4"each side (approximately 10" for '12" board).Rough opening Door opening width 1V4", dooropening height 1/2". Hold drywall stud back 4"each side (approximately 10" for '12" board).Preliminary steps: Gut RAGa studs to frame heightless 4".Gut jambs to floor if necessary.Preliminary steps:Step 1: Shoot drywall track to floor. Put RAGa studsin wall (no clips).Step 1: Shoot drywall track to floor. Put RAGa framesin wall. Remove short stop pieces at tops ofjambs and screw jambs to header clips. Replacestop pieces.Step 2:Plumb hinge stud and screw off gyp-board.Align strike stud with hinge stud using dooropening plus 3/16" and screw off gyp-board.Step 2:Plumb hinge stud and screw off gyp-board.Step 3:Put frame over studs and install header. Screwjambs to headerclips.Screw hinge jamb to stud.Attach stop.Step 3:Step 4:Hang door, if available, and swing closed.Adjust strike jamb for even cracks at top andedge of door. If door not available,adjust headerwith levefand jamb with spreader. Screw strikejamb to stud. Attach stop. Note: Studs are notdrilled for hinge screws;RAGa R-25self-drillingscrews are recommended, pages 00 & 00.Hang door, if available, and swing closed.Adjust strike jamb for even cracks at top andedge of door. If door is not available, adjustheader with level and jamb with spreader.Screw off gyp-board. Note: stud segments aredrilled for hinge screws but are not threaded;RAGa R-25 or R-25ND self-threading screwsare recommended, pages 00 & 00.Gut jambs to floor if necessary.Note: Install aluminum studs with 1" No.6 drywall screws,spaced 12" on center, each side of wall. Lowermostscrews shall penetrate floor track.Note: Install hinge and strike stud segments with 1" No.6 dry·wa II screws, using th ree screws each side of wall for eachsegment. Lowermost screws shall penetrate floor track.Approximate time to install frame and hinges:One carpenter - 26 minutesApproximate time to install frame and hinges:One carpenter - 16 minutesApproximate time to hang pre-machined door:One carpenter - 4 minutes(no lockset)Approximate time to hang pre-machined door:Orie carpenter - 4 minutes(no lockset)Installation times for both types of frames are based on all required tools and material being available at aprepared rough opening.140
RACO FREESTANDING frame styles compared.AS INSTALLEDAS SHIPPED[h . ()(Shown33/4" or 47/8"Scale: 6" 1'0"New TRIMSTYLE designo0oo oSpecify regular studsfor51."drywall;specify shim studs for,,," drywall.Do () 0o0 .j\.c 5/8" or '12"Scale: 6" 1'0"RACO CLASSIC design with separate studsr-I12""(Shown)3""-110' 4, 1 5/8"or '/2"Scale: 6" 1'0"RACO CLASSIC design with FASTRAK studsRACOiQ)i!J i!J IRl RaglandBox55527ManufacturingHouston, lx. 77055Co., Inc.I (800) 272-RACOm IillI (713) 682-6100675
RACO Freestanding CLASSIC prefinished aluminum door frames andsidelite frames. (U.S. Patent Nos. 3,676,966; 3,886,688; and 4,126,343)."Freestanding"9/32"1 I,-L-r- ;TrT1112"en FS-1L"JCLASSIC frames in-stall ceiling height or less in conjunctionwith FS-1 integral type door frame headers. These headers terminate at thejambs of the frame. Any type of partitionheader except continuous PR-1 can beused. Freestanding sidelite frames use amodified header consisting of PR-1 orPR-6 which terminate at the frame jambsand carry a section of PR-4 over the doorsection, and PR-5 over the glass.'fI't')',-- 13{. Polypropylenepile soundseal,Freestanding CLASSIC frames are furnished with aluminum attachment studsor stud segments. The attachment studscarry all door weight and are secured directly to wall panels for maximumstrength and elimination of twisting moment. The header serves as a thrustmember to carry the door weight from thehinge to the strike side of the frame. Inthis manner,any pull-out tendency due todoor weight is effectively overcome.continuousFS-2Optionalprep. for light switchFS-3FS-2FS-3NOTE: Frames taller than 7' furnished with extra lengthjambs unless ordered exact length. See page 140 forinstallation instructions.RAca Freestanding CLASSIC frames upto 3' x 9', single, and 6' x 9', double arefire-rated and 20-minute labeled for usein one-hour partitions in all throat sizes,21/4". 33/4" and 47/8". Single sideliteframes can also be rated with 121/2" exposed width of rated glass. Only three41/2" x 4" template hinges per jamb arerequired for any of the rated frames (.134ga. only).R-46DStrikeStrikeClip(shown withStrikePlate NIC). CliP.(S ownWithStnker- I :R-46DlJR-31 47/8" ASA strike prep(for 31." latch or lock bolt) a'R-46SD Plate NIC).fJ. R-46SD R-31SAluminum attachment studs for each ofthe three throat sizes of FreestandingCLASSIC frames are available to accommodate either 1/2" or 5/8" thick gypsumboard. The studs for 5/8" board are called"regular" studs and those for 1f2" boardare called "shim" studs. Studs can be either screw-attached or secured withmodified contact adhesive (no screws).Thus the three stock jamb members, series 225, series 375, and series 487 arereadily adapted to a wide range of partition designs.23/4" ASA strike prep(for 3/." latch or lock bolt)FreestandingCLASSIC door frame shown with selfheader, FS-1. Frame IllustratedIs right hand swing.Optional prep. for light switch - pp 58, 59.As ShippedAs Installed"Separate studs" is the designation for Freestanding CLASSIC frames furnished with unassembled, full-length aluminum studs; thestuds are installed independently so that drywall screws can be covered by jamb membersof the frame. Installation time for Freestandingframe with separate studs: 26 minutes for oneperson. (Note: Hinge holes in full lengthsstuds to be job drilled; use R-25 hinge screws.)80Freestanding CLASSIC frames are prefinished in 0-3 dark bronze, satin black,or frost white Duralaq. This hard, chip-resistant baked coating is comparable toautomotive finishes. Other colors and allanodized finishes lareavailable on special order. Series'375 frames are stockedin natural anodized finish in addition toDuralaq.As InstalledAs Shipped"FASTRAKstuds"is the designationforFreestanding CLASSIC frames with factoryassembledstud segments;framessoequipped are fastest to install and can use thedoor as a template for maximum precision.Drywall screws require spackling. Installationtime for FreestandingFASTRAK frames: 16minutes for one person. (Note: Hinge holesfactory punched; use R-25 hinge screws.)6Either 23/4" or 47/8" ASA strike plates areheld in place by means of cold-drawnsteel clamp-in strike boxes which are furnished with each frame. Prep. is available for electric strikes (see page 56),dead bolt locks (page 55), and jambmounted light switches (page 59).RACO OOIril """" ",'0",,,,, 1f" ""'I!;;;;"Ragland Manufacturing Co., Inc.Box 55527l:iouston,77055(713)682-6100I (600)Tx.272-RACOI'
2-R56BR-20B(w/PR-6)(w/PR-l)'x" . . -. ,','','-'",',"".PR-4(w/2-R34 if PR-l)Prep. for 4112" hinges (.134" thick)Optionalprep.for light switchFS-2(with PR stud orstud segments)Aluminumstud segmentsNOTE: Frames furnished with extra lengthunless ordered exact length.iambsFreestanding CLASSIC single frame shown with continuous header, PR-6. Frame illustrated is right handswing. Optional prep. for light switch - see pages 58, 59. Sidelite strike jambs are strengthened by full-strengthstiff-leg side lite studs. Additional security can be gained by 'Use of horizontal mull at strike jamb (page 71).Sidelites can be attached to either orboth jambs of Freestanding frames.Glazing extrusions provide 5/8" total coverage for glass, a feature of particular impC' nce to glazers where temperedis installed. Frames with glass attn. .) jamb are furnished with 12-gagesteel stud with 10-gage clip welded on forrigid attachment to header. See page 71for similar detail.RACOfO)iOllf'll m iIlIDlE BoxRagland55527ManufacturingHouston. Tx. n055Co., Inc.(713) 682-6100 1(800) 272·RACOInstallation suggestions: Gypsum board opening is door width plus exposed glasswidth plus 25/8" for frame illustrated.1.2.3.4.5.6.AlternatePR-26 IIPInstall header. Shoot drywall track to floor each side of opening.Install PR-5M. Trim bottom of jambs if required.Install hinge jamb and header with R-18 clip secured to header.Hang door or use spreader to position strike jamb; secure clips.Install PR-5 and PR-lO base portion. Field measure for glass.HighboyInstall glass, add PR-7D upper portions. Install vinyl furnished with frame if fitSillacceptable.NON-STOCK681
Freestanding CLASSIC prefinished aluminum door frames and sidelite frameslYpical door opening sizesAll frames are fabricated toorder in any size to 18' jambheight. Hardware locationsare optional. Stock framesare 3-hinge spaced 5"-10"and equal with 47/8" ASAstrike centered 38" fromfloor.Designer series 225 21/4" throat openingUniversal series 375 33/4" throat openingInstitutionalseries 487 47/8" throat openingStock finishes: 0-3 dark bronze, satin black, and frost whitePart & NumberNo. ScaleDuralaq, and black, bronze or natural anodized available on special order. Series 375 stocked in natural anodized in addition toDuralaq.Complete FreestandingCLASSIC door fram s - shipped withaluminum studs, steel mounting clips, uncut snap-in header,RACO speed screws, and R-46 strike clip.FS-1FS-2FS-3orFS-2(a)Specify "Separate studs" (S) frames if separate full lengthstuds are desired. Specify "FASTRAK@ studs" (F) for factoryinstalled stud segments. Prices of "F" and "S" types aresame for single frames.(b)(c)(d)Specify 5/8" or '/2" gypsum board.Specify size, swing and finish.Gypsum board openingrequired is door width plus1'/4". First drywall stud should be held back 4" each sideof frame for 5/8" board, 10" for 1/2" board. Allow '/2"clearance at head.FS-123F or S - (Single)FS-122F or S - (Double),IiPR-1 or PR-6PR-4I/i"FS-2PR-3l:PR-5/1I::!:::i /PR-5M;j;/0:PR-7D(e)FS-234F or S-LT (Single)FS-224F or S-LT (Double)I!r(1/PR-5PR-4F-23' xx7'3'9'10'/2"F-5}F-36' x 7'101/2"F-46' X 8'10'12"6' Xx7'9'10'/2"6'3'3'x7'3' x 3'X7'10'/2"3'xF-6}F-93' x 8'10'/2"X3' x 3' x 9'10'/2"6'3'xF-107'x6' x 3' x 7'10'/2"6'X3'X8'10'/2"6'X3'X9'10'/2"3/4" to 1door frameswithF-133' xxratedxsldelites6'x with3' xxx 7'10'/2"7'10'/2"12'/2"max. twofirehori6' gextrusionsshippedinGypsum gandfinish&quiredisdoorwidthplus3'xheight3'glassx 9'10'/2"F-12clips,glazingvinylandRACO3'xx 3'6'3' xx 3'3' xspeedx 7'3' x 7'shippedwith lengths.steel studs, mountinguncut stock(e).ab ve(c)(d)7'10'/2"X3' x 8'10'/2"Gypsum board opening required is door width olus glassI' width plus 25/8", door height Glazing extrusionsshipped in uncut stock lengths.(1)PR-1 or PR-6mullbar.-5Mor safety'12" glass.F-13'Complete FreestandingCLASSIC door frames with sideliteframes - shipped with aluminum studs, snap-in header, steelmounting clips, glazing vinyl and RACO speed screws. (One steelstud with double frames.)(a) Specify "Separate studs" (S) frames if separate full lengthstuds are desired. Specify "FASTRAK studs" (F) for factoryinstalled stud segments at no change in prices.(b) Specify 5/8" or '/2" gypsum board; specify whether '/4",3/8",or '/2" glass.(c) Specify size, swing and finish.(d) Specify width of glass opening; 12'12" max. fire rated withhorizontal safety bar" .PR-5ShopDrawingFonns3' x 6' x 3' x 9'10'/2"PR-5MIIPR-5PR-2Il/JPR-7DFS-234-2 LT (Single)FS-224-2 LT (Double)---. . \J. F&1Transom\bar for panell ; rl 82Transom""PR-4PR-22bar for glassi", ii"Hinge jamb at glassStrike jamb at glass.\Left hand", plale'!:Channel[]'1 b!i]brackelback'::,1//' ,-/Io\fRight hand"I. Horizontalsafety bars. Specifytype desired, PR-7M or PR-22. Barrequiredfor fire-ratedsideliteframes. Additional bars pg. 71.6/\///Swing designationsfor RACO frames.Non-handed frames are not available.RACOIQ) """.". IrtnliAl"""",,,,,Ragland Manufacturing Co., Inc.In055Box 55527Houston,Tx.272-RACO(713)682-6100(BOO)
)PR,,6Mo I.l,,I\I-'- --'IINSTAlLATION INSTRUCTIONS FOR A BoMOWEDFREESTANDING CONDIT/ON(]'1 LITEIVl'ri - . ' "" .1,.'rVl,.'"'0EI0-bOJI-I-lQ)I,0eeCO .\tI-1. r, ;CJdPR 6/PR-5I'rr-i're ,OJ.0r-iCo0l'tl -,.00)eIen'"'0.f-) 0l'tl'"'0 ,0 1c:OJOJO'lII-0 N-I-l-:.L-I ;0I. . (2)Rough Opening Dimensions:Width: daylite 1-114"Height: dqylite 1-314"(add 518" ifsill sitting on floor).All dimensions may vary to field conditions(allow approximately 1/8").eachI.1.) Cut sample (4" - 6") of PR-6 and PR-7D, capover rough-in opening at each corner of headand sill to detennine length of PR-5M verticaljambs. Jambs must be field notched 718" at topand 518" at bottom to fit over drywall. Afternotching is complete, install PR-5M jambs andallow to float until next step is complete.2.) Determine finish width of lite, cut PR-6 and PR-7Dand attach at head and sill with drywall screws.All joints to be butt-cut.3.) Using 2 each R-56B clips at each corner, securePR-5M to head and sill making certain joints aretight .4.) Measure and cut PR-5 snap-in header and PR-7Dsnaps' (wide and narrow).5.) Field measure and install desired thickness of glass(114" and 318" typical,' specify when ordering RACOaluminum material). RACO rubber gasket installs ononly one side of glass .eachcornerR-56BclipsLPR-5MPR-7DLf) 0.PR 70'rll 1 II K--36" I I.K--3'3"-- tI
RACO Freestanding CLASSIC prefinished aluminum door frames and sidelite frames. (U.S. Patent Nos. 3,676,966; 3,886,688; and 4,126,343). Freestanding CLASSIC frames are fur nished with aluminum attachment studs or stud segments. The attachment studs carry all door wei
1 Raco Fittings tRaining Manual CONFIDENTIAL History of raco RACO was founded by Walter Roach and Earnest Appleton in Chicago, Illinois in 1921.
authorized by RACO, please complete the authorization form in the Owners Manual and return the form to RACO to ensure the warranty. Under no circumstances will RACO be responsible for consequential or secondary damages. The defective product should be returned, insured and freight prepaid, securely packaged to the address listed below.
WCF9 Classic Window 1 Pane (Fixed) 3.6 24.27 WCS9 Classic Window 1 Pane (Sash) 5.8 33.14 WCF12 Classic Window 1 Pane (Fixed) 3.8 26.28 WCS12 Classic Window 1 Pane (Sash) 6.5 36.41 . CLASSIC TOPPERS . KG PRICE QTY WCT6 2 Pane Classic Top Lite Window 5.8 32.19 WCT9 2 Pane Classic Top Lite Window 6.9 38.21 .
Solid VERSA-LOK Standard units do it all, including easy-to-install freestanding walls with the same natural, classic look as VERSA-LOK Standard retaining walls. VERSA-LOK units are easily modified by splitting off the back of the units. From these split units, installers can build freestanding walls with textured faces on both sides.
INSTALLATION INSTRUCTIONS 30" (76.2 CM) FREESTANDING GAS RANGES Table of Contents . Install anti-tip bracket to floor or wall per installation instructions. Slide range back so rear range foot is engaged in the slot of the anti-tip bracket. . G.This shaded area recommended for installa
installation instructions freestanding 30" gas with double oven range installation and service must be performed by a qualified installer. important: save for local electrical inspector's use. read and save these instructions for future reference. _ for your safety: do not st
installation instructions 30" (76.2 cm) freestanding gas ranges instructions d'installation des cuisiniÈres À gaz autoportantes de 30" (76,2 cm)
Kata Kunci : Asam folat, Anemia, Gagal Ginjal Kronik, Rawat Inap . ii ABSTRACT A STUDY OF FOLIC ACID USE IN ANEMIC CHRONIC RENAL FAILURE PATIENTS HOSPITALIZED IN RSUD SIDOARJO Chronic renal failure is disturbance of kidney functions that progressive and irreversible where the ability of kidney to maintain the metabolism and liquid balance also electrolit causes uremic. Anemic is a complication .
