SOUTHWEST RESEARCH INSTITUTE CALIBRATION LABORATORY MEMORANDUM
SOUTHWEST RESEARCH INSTITUTECALIBRATION LABORATORYMEMORANDUMMarch 21,2005To:KENCHIANG DN20 B57From:Walt Hill, Metrology Group LeaderInstitute Calibration LaboratorySubject: Status of Calibration SupplierManufacturer/Model: TROEMNER 1GDescription: WEIGHT, CLASS 2Serial Number: 66665Asset Number: 01 1115Work Order Number: 303063075Date Calibrated: March 16, 2005Supplier: TROEMNER, THOROFARE NJ NVLAP - 856 686-1600Remarks: TROEMNER CERT. # 3 13672-1.(/Supplier is on the Approved Suppliers List (ASL).( ) Supplier is not on the Approved Suppliers List.(Aalibration is IS0 17025 accredited.( ) Calibration is not I S 0 17025 accredited.( ) There is no known supplier to meet IS0 17025 accreditation at this time.Please notify the Institute Calibration Laboratory, extension 52 15, of any discrepancies with the it m rcalibration documentation.Attachment(s)m:\nonasl2.rpt Rev 7 Dec 01
TROEMNERHenry Troemner LLC201 Wolf Drive P.O. Box 87 Thorofare, NJ 08086-0087 Phone: 856-686-1600 Fax: 856-686-1601www.troemner.com e-mail: troemner@troemner.comPage 1 of 7 PagesWeightCertificate Number 3 13672-1Date of Calibration 16-MAR-2005SECTION 1: NAME AND ADDRESS OF CUSTOMEREnd userSouthwest Research Inst .6220 Culbera RoadSan Antonio TX 78238-5166ClientSouthwest Research Inst. (TX)P.O.Box 28510Attn: Accounts PayableSan Antonio TX 78228-0510SECTION 2: APPROVED SIGNATORYKatharine EllisSECTION 3: PERSON PERFORMING WORK&Stephanie FoyleSECTION 4: CERTIFICATE INFORMATIONDescription of Masses: Troemner S/S S/K l g Individual WeightAccuracy ClassOrder NumberConstructionMaterial::::ASTM E617-97 Class 2579498ROMTwoPieceStainless SteelDate ReceivedDate of CalibrationDate of IssueWeight N 5: ENVIRONMENTAL CONDITIONS DURING TESTTemperature: 21.80 CPressure: 76 1.71 mm HgRelative Humidity: 42%SECTION 6: PERTINENT INFORMATIONThe Weights listed on this calibration report have been compared to reference mass standards that aredirectly traceable to the National Institute of Standards and Technology under Test No. 822/270236-04.Reference standards and balances used to perform the calibration are listed in Section 10.The weights calibrated for this report have been calibrated in accordance with Troemner'scalibration process. The calibration performed meets Level 11criteria as described in theNIST/NVLAP Technical Guide 150-2.This calibration also meets specifications as outlined in IS0 9001, ISO/IEC 17025,ANSI/NCSL 2540-1-1994, NCR Document lOCFR5O Appendix B, and applicable documents.This certificate of calibration shall not be reproduced except in full, without the written approval of Troemner, LLC. This certificate ofcalibration must not be used by the customer to claim product endorsement by NIST, NVLAP or any agency of the U.S. government.
Henry Troemner LLC201 Wolf Drive P.O. Box 87 Thorofare, NJ 08086-0087 Phone: 856-686-1600 Fax: 856-686-1601www.troemner.com e-mail: troemner@troemner.comPage 2 of 7 PagesWeightCertificate Number 3 13672-1Date of Calibration 16-MAR-2005NAME AND ADDRESS OF CUSTOMERClientSouthwest Research Inst. (TX)P.O.Box 285 10Attn: Accounts PayableSan Antonio TX 78228-0510End userSouthwest Research Inst.6220 Culbera RoadSan Antonio TX 78238-5166SECTION 7: TRUE MASS (MASS IN VACUUM) CALIBRATION DATANominalSerialMass ValueNumber1 g666651 Density is assumed unless otherwise stated--------- True Mass ---------As Found1.000011 gAs Left1.000011 gDensity'Uncertaintyof Weight( or-)8.0300 g/cm30 . 0 0 5 mg
TROEMNERHenry Troemner 11C201 Wolf Drive P.O. Box 87 Thorofare, NJ 08086-0087 Phone: 856-686-1600 Fax: 856-686-1601www.troemner.com e-mail: troemner@troemner.comPage 3 of 7 PagesWeightCertificate Number 3 13672-1Date of Calibration 16-MAR-2005NAME AND ADDRESS OF CUSTOMERClientSouthwest Research Inst. (TX)P.O.Box 28510Attn: Accounts PayableSan Antonio TX 78228-0510End userSouthwest Research Inst .6220 Culbera RoadSan Antonio TX 78238-5166SECTION 8: MASS IN AIR CALIBRATION VALUE VS. REFERENCE DENSITY 8000 kg m -3NominalSerialMass ValueNumber1 g66665---- Conventional Mass Value ---As FoundAs Left1.000011 g1.000011 gUncertaintyTolerance( or-)( or-)0.005 mg0.0540 mg
TROEMNERHenry Troemner LLC201 Wolf Drive P.O. Box 87 Thorofare, NJ 08086-0087 Phone: 856-686-1600 Fax: 856-686-1601www.troemner.com e-mail: troernner@troemner.comPage 4 of 7 PagesWeightCertificate Number 3 13672-1Date of Calibration 16-MAR-2005NAME AND ADDRESS OF CUSTOMERClientSouthwest Research Inst. (TX)P.O.Box 28510Attn: Accounts PayableSan Antonio TX 78228-0510End userSouthwest Research Inst.6220 Culbera RoadSan Antonio TX 78238-5166SECTION 9: MASS IN AIR CALIBRATION DATA VS. REFERENCE DENSITY 8000 kg mNominalMass Value1 gSerialNumber66665-- Conventional Mass Correction -As Found0.011 mg-3As LeftUncertainty( or-)Tolerance( or-)0.011 mg0.005 mg0.0540 mg
TROEMNERHenry Troemner LLC201 Wolf Drive P.O. Box 87 Thorofare, NJ 08086-0087 Phone: 856-686-1600 Fax: 856-686-1601www.troemner.com e-mail: troemner@troemner.comPage 5 of 7 PagesWeightCertificate Number 3 13672-1Date of Calibration 16-MAR-2005NAME AND ADDRESS OF CUSTOMERClientSouthwest Research Inst. (TX)P.O.Box 28510Attn: Accounts PayableSan Antonio TX 78228-0510End userSouthwest Research Inst.6220 Culbera RoadSan Antonio TX 78238-5166SECTION 10: CALIBRATION PROCEDURE DATANominalMass Value1 sed03/31/05 UMT5/6-116CalDue03/31/05ProcedureUsedA-B-A
TROEMNERHenry Troemner LLCI201 Wolf Drive P.O. Box 87 Thorofare, NJ 08086-0087 Phone: 856-686-1600 Fax: 856-686-1601NAME AND ADDRESS OF CUSTOMEREnd userSouthwest Research Inst.6220 Culbera RoadSan Antonio TX 78238-5166www.troemner.com e-mail: troemner@troemner.comPage 6 of 7 PagesWeightCertificate Number 3 13672-1Date Of Calibration 16-MAR-2005ClientSouthwest Research Inst. (TX)P.O.Box 285 10Attn: Accounts PayableSan Antonio TX 78228-0510SECTION 11: GENERAL INFORMATIONThis calibration was performed in Troemner's High Precision Level I Mass Metrology Laboratory at201 Wolf Drive, Thorofare, New Jersey 08086 unless otherwise noted on page one. The internal proceduresused are CAL-CLASSI, CAL-MMAP, and NIST HB 145.SECTION 12: DEFINITIONS AND TERMSMASS IN A VACUUM - The mass of a weight as if it were measured in a vacuum. Also known as True Mass.MASS IN AIR - The conventional value of the result of weighing in air, in accordance to InternationalRecommendation OIML R 33. For a weight taken at 20" C, the conventional mass is the mass ofa reference weight of a density of 8000 kgm-3which it balances in air of a density of 1.2 kg m-?AS FOUND MASS IN A VACUUM - The measured value of the mass(es) as they were received by Troemner.If the customer requires cleaning prior to calibration, the after cleaning value would be reported.AS LEFT MASS IN A VACUUM - The measured value of the mass(es) after they were adjusted, repairedor replaced when necessary. The As Found Mass in a Vacuum will equal the As Left Mass in a Vacuumif the mass(es) did not require adjustment, repair or replacement.NOMINAL MASS - The mass value as marked on the weight.CORRECTION - The difference between the mass value of a weight and its nominal value. A positivecorrection indicates that the mass value is greater than the nominal value by the amount of the correction.AS FOUND CONVENTIONAL MASS CORRECTION - The conventional correction of the result, as it wasreceived by Troemner, of weighing in air in accordance to International Recommendation R 33. For aweight taken at 20" C, the conventional mass is the mass of a reference weight of density 8000 kg m -3which it balances in air density of 1.2 k g m -3. If the customer requires cleaning prior to calibration,the after cleaning correction would be reported.AS LEFT CONVENTIONAL MASS CORRECTION - The conventional correction of the result, after adjust-,ment repair, or replacement of weighing in air in accordance to International Recommendation R 33. Fora weight taken at 20" C, the conventional mass is the mass of a reference weight of density 8000 kg m -3which it balances in air density of 1.2 kg-m'? The As Found will equal the As Left Conventional MassCorrection if the mass(es) did not require adjustment, repair or replacement.UNCERTAINTY - The error in assignment of the correction due to the measurement process. Uncertaintyis calculated in accordance with UKAS document M3003 using a coverage factor of k 2 ( k 2 definesan interval having a level of confidence of approximately 95 percent). The error does not include theeffects of magnetism. (continued on next page)
TROEMNERHenry Troemner LLCP201 Wolf Drive P.O. Box 87 Thorofare, NJ 08086-0087 Phone: 856-686-1600 Fax: 856-686-1601www.troemner.com e-mail: troemner@troemner.comPage 7 of 7 PagesWeightNAME AND ADDRESS OF CUSTOMEREnd userSouthwest Research Inst.6220 Culbera RoadSan Antonio TX 78238-5166Certificate Number 3 13672-1Date of Calibration 16-MAR-2005ClientSouthwest Research Inst. (TX)P.O.Box 285 10Attn: Accounts PayableSan Antonio T X 78228-0510SECTION 12: DEFINITIONS AND TERMS (continued)TOLERANCE - Defines the limits in which the correction value and the uncertainty must fall to meet thetolerance specification for the given Class.AS FOUND CONVENTIONAL MASS VALUE - The measured value of the mass(es) as they were receivedby Troemner, of weighing in air in accordance to International Recommendation R 33. For a weight takenat 20" C, the conventional mass is the mass of a reference weight of density 8000 kg*m-'which it balancesin air density of 1.2 k g m - If .the customer requires cleaning prior to calibration, the after cleaning valuewould be reported. F denotes Out of Tolerance Weight.AS LEFT CONVENTIONAL MASS VALUE - The measured value of the mass(es) after they were adjusted,repaired or replaced when necessary, of weighing in air in accordance to International RecommendationR 33. For a weight taken at 20" C, the Conventional Mass is the mass of a reference weight of density8000 kg*m-3which it balances in air density of 1.2 kgm-3. The As Found will equal the As LeftConventional Mass Value if the mass(es) did not require adjustment, repair or replacement.ASTM E617-97* - Weights meet the tolerance specification for ASTM E617-97. Weights 2kg - l gscreened for magnetism using a Gaussmeter.
SOUTHWEST RESEARCH INSTITUTE CALIBRATION LABORATORY MEMORANDUM March 21,2005 To: KENCHIANG DN20 B57 From: Walt Hill, Metrology Group Leader Institute Calibration Laboratory Subject: Status of Calibration Supplier Manufacturer/Model: TROEMNER 1 G Description: WEIGHT, CLASS 2 Serial Number: 66665 Asset Number: 01 1 1 15 Work Order Number: 303063075
Calibration (from VIM3) Continued NOTE 1 A calibration may be expressed by a statement, calibration function, calibration diagram, calibration curve, or calibration table. In some cases, it may consist of an additive or multiplicative correction of the indication with associated measurement uncertainty. NOTE 2 Calibration should not be .
1.7.1.1 e) v) The laboratory may replace a calibration standard provided that a. the laboratory analyzes the replacement standard within twenty-four (24) hours of the original calibration standard analysis for that particular calibration level; b. the laboratory replaces all analytes of the replacement calibration standard if a standard within the
Host action Target needed * : Timings are given for information only, they can vary depending on the Host capabilities Calibration Data result Calibration data Calibration data Calibration data Calibration data Device initialization SPADs calibration Temperature calibration Offset calibrat
calibration. The vertical comparator was built during the year 2003. The calibration facility is designed to calibrate up to 3-m-long invar rods, both for system calibration of digital levels and for tradi-tional rod calibration. SLAC System Calibration Facility The procedure of system calibration of digital levels is described
1 Manual calibration introduction 3 1.1 Purpose 3 1.2 Manual calibration software 3 2 Manual calibration overview 3 3 Manual calibration process 4 3.1 Setup MCR program 4 3.2 Calibration pattern positioning 9 3.3 Capturing pattern image 14 3.4 Using the Synergy Calibration tool 18 3.5 Fine tuning side images 24
Calibration C-0942, Mechanical(Dimensional, Pressure, Mass & Volume) Calibration C-0943 & Thermal Calibration C-0944. Our company is also ISO 17025:2005 Certified for Mechanical Calibration, Elctro Technical Calibration & Thermal Calibration. The firm is proud to have earned distinction in its various services and we are performing as a
SOUTHWEST FREEWAY TRANSITWAY Prepared for Robert Reid, Inc. Texas Transportation Institute The Texas A&M University System Houston, Texas September 1993 . . 13 U.S. 59 Southwest WB Frontage Road to Edloe NB 3,065 3,349 4,575 14 Edloe SB to U.S. 59 Southwest WB Frontage Road Exit 2,180 2,382 3,254 15 Edloe NB - North of U.S. 59 Southwest 7,558 .
The aim of this book is to introduce the idea of Extensive Reading by using Graded Readers, and to show how it should fit into an overall reading program. This booklet will: explain why Extensive Reading is so important and necessary for all language learners show how and why Extensive Reading works show teachers how to start an Extensive Reading Program suggest a balanced reading approach for .
