AL/PL Series Dual Air Valves - Crispin Valve
Dual Air ValvesAL/PL Series Dual Air ValvesCustomize Your Air Release RequirementsAL/PL SERIESValve Function Single pipelinelocation when bothAir & Vacuum andPressure Valves arerequired at one pointon a pipeline Meets AWWA C-512Please Refer to Air & Vacuumand Pressure Air Release Valvefor Parts Lists.he sizing of a Dual or Combination Valve requires the samedata and parameters of the Air & Vacuum Valve and PressureAir Release Valve. Subsequently, if the required pressureorifice size varies from the standard pressure orifice offered witheach Combination, then a Dual Valve, with its flexibility, can beapplied to accommodate specific orifice requirements.The flexibility of the Dual Valve allows a wide variety of conditions to be addressed. For example: if the system pump capacitywere to dictate the air and vacuum sizing of 2” for air release, thenthat same capacity would normally require a Pressure Air ReleaseValve in the Midget size.However, if a greater amount of air was expected to beentrained in the liquid, because of siphoning through leaky joints orpacking, or because of turbulence, etc., then a larger PressureValve with a greater orifice size could be provided.Also, should vacuum relief be the deciding Air and Vacuumsizing parameter, because of pipe slope, size, and/or materials ofconstruction, then the corresponding Universal or CombinationPressure Air Release orifice could be larger than would actually berequired for the system.In this case, the flexibility of the Dual Valve would accommodate the system performance requirements.TDimensions and 62/PL20Valve Size eight (B)13 1/4”14 3/4”18 1/4”18 1/2”16”19 3/4”20 1/4”20 1/4”23 3/424 1/4”22 1/4”22 1/2”25 1/2”26”29”29 3/4”32 1/2”33 1/4”34 1/4”35”36 1/2”37 1/2”Width (A)9 3/4”12 1/4”12 1/4”12 1/4”16”16”16”20”20”20”21”21”24 1/2”24 1/2”33 3/4”33 3/4”34 1/2”34 1/2”36 1/2”36 1/2”39 1/4”39 3195245747758281023121011431326* Available up through 24”. Please contact factory for sizes 18” and larger.8AL/PLCrispin Valve, 600 Fowler Ave., Berwick, PA 18603 1-800-AIR-VALV T: (570) 752-4524 F: (570) 752-4962 WWW.CRISPINVALVE.COM sales@crispinvalve.com
Submittal Sheet for Crispin A/M Series1/2” Dual Body Combination Air ReleaseManufactured in compliance with ANSI/AWWA C51295111110502484114 12142950PARTS LIST FOR AIR & VACUUMDESCRIPTIONMATERIALTOPCAST IRONFLANGECAST IRONBODYCAST IRONGASKETARMSTRONG N-8092SEATBUNA-N RUBBERFLOATSTAINLESS-STEELHANGERSTAINLESS STEELCUPSTAINLESS STEELRIVETSTAINLESS STEELBOLTSTEELNUTSTEELDIFFUSERSTAINLESS STEELPLUGBRASSINTERFERENCE PINSTAINLESS STEELASTMA126 CL. BA126 CL. BA126 CL. BN/AD2000A240A240A240A582A307A563A240B505A582PARTS LIST FOR PRESSURE RELEASE UNIT12456789101112H13291245VALVE SEATSTAINLESS STEELA276PLUNGER BUTTONVITOND2000VALVE LEVERSTAINLESS STEELA240SCREW (DRIVE)STAINLESS STEELA193BALL FLOATSTAINLESS STEELA240HINGE PINSTAINLESS STEELA580HINGE BUTTSTAINLESS STEELA240BOLTSTEELA307SCREWSTAINLESS STEELA193FLANGECAST IRONA126 CL.BBODYCAST IRONA126 CL.BGASKETARMSTRONG N-8092N/APLUG (NOT SHOWN)BRASSB505PARTS LIST FOR CONNECTING PARTSNIPPLEELBOWNIPPLETEESTEELMALLEABLE IRONSTEELMALLEABLE IRONA53A338A53A338The Air and Vacuum Valve shall operate bysealing the BUNA-N rubber outlet seat with aperipherially guided float as the liquid entersthe valve chamber to raise the float. All CrispinValves are hydrostatically tested to 150% oftheir maximum working pressure.The Pressure Valve shall operate through acompound lever system and shall have a” orifice with valve sealingfaces, of an adjustable BUNA-N rubber valveand (stainless steel or PVC) and shall operateat PSIG and be capable ofpassing SCFM of air. Valveswhich use a needle valve to seal the orificewill not be acceptable.CP1CP2The combination air valve(s) shall be installedat high points in the system or at points selected by the engineer. This will permit discharging the surge of air from an empty line whenfilling and relieve the vacuum when the line isdraining, or is under negative pressure. Thevalve(s) shall also release the accumulationof air when the system is under pressure.Valve construction shall be ”NPT screwed or ANSI Class (125,250)flanged inlet connection and shall be cast iron body, top, and inlet flange(where required), stainless steel float with bronze and (brass or stainless steel)trim. Refer to Air & Vacuum and Pressure Air Release specifications for Valvedescription.The valve(s) shall be CRISPIN Model Dual Air Valve(s), TypeN, (PVC seat and BUNA-N rubber valve) or Type P (stainless steel seat andBUNA-N rubber valve) pressure valve(s) as manufactured by Crispin-Multiplex Manufacturing Co., Berwick, Pa. The valve(s) shall include a CrispinPressure Air Release Valve.Option: A protectop shall be supplied to prevent debris from entering the outlet of the Air and Vacuum Valve.Option: (Where pressures are greater than 300 psig), the valve(s) shall beANSI Class flanged inlet connection and shall have a (steel,stainless steel, or ductile iron) body, top and inlet flange.Standard operating pressure for Crispin Air Valves is 20 to 150 PSIG.Please check one of the following if your operating needs differ:2 to 40 PSIG151 to 300 PSIGOrifice OptionsDIAMETER5/321/83/321/163/641/32MAX. PRESSURE40 PSIG50 PSIG85 PSIG150 PSIG200 PSIG300 PSIGDISCHARGE RATE12.6 SCFM9.6 SCFM8.3 SCFM6.1 SCFM4.5 SCFM3.2 SCFMSUBMITTAL SHEET FOR A/M SERIESSpecifications113Date: October, 2001Size SpecificationsMODELA5/M5INLET SIZE1/2” NPTOUTLET SIZE A1/2” NPT12.00B9.00WT.209Crispin Valve, 600 Fowler Ave., Berwick, PA 18603 1-800-AIR-VALV T: (570) 752-4524 F: (570) 752-4962 WWW.CRISPINVALVE.COM sales@crispinvalve.com A/M
Submittal Sheet for Crispin AL/M Series1”–3” Dual Body Combination Air Release10ADate: October, 5CP26SECTION A-ACSUBMITTAL SHEET FOR AL/M SERIESManufactured in compliance with ANSI/AWWA C512CP1CP3Orifice OptionsDIAMETER5/321/83/321/163/641/3229** Includes ANSI #125 or #250companion flange and nippleSpecificationsThe combination air valve(s) shall be installed at high points in thesystem or at points selected by the engineer. This will permit discharging the surge of air from an empty line when filling andrelieve the vacuum when the line is draining, or is under negativepressure. The valve(s) shall also release the accumulation of airwhen the system is under pressure.The Air and Vacuum Valve shall operate by sealing the BUNA-N rubber outlet seat with a peripherially guided float as the liquid enters thevalve chamber to raise the float. All Crispin Valves are hydrostatically tested at 150% of their maximum working pressure.The Pressure Valve shall operate through a compound lever system and shall have a ” orifice with valve sealingfaces, of an adjustable BUNA-N rubber valve and (stainless steel orPVC) and shall operate at PSIG and be capableof passing SCFM of air. Valves which use a needlevalve to seal the orifice will not be acceptable.Valve construction shall be ” NPT screwed or ANSIClass (125,250) flanged inlet connection and shall be cast ironbody, top, and inlet flange (where required), stainless steel float withbronze and (brass or stainless steel) trim. Refer to Air & Vacuumand Pressure Air Release specifications for Valve description.The valve(s) shall be CRISPIN Model Dual AirValve(s), Type N, (PVC seat and BUNA-N rubber valve) or Type P(stainless steel seat and BUNA-N rubber valve) pressure valve(s)as manufactured by Crispin-Multiplex Manufacturing Co., Berwick,Pa. The valve(s) shall include a Crispin Pressure Air Release Valve.Option: A protectop shall be supplied to prevent debris from entering the outlet of the Air and Vacuum Valve.Option: (Where pressures are greater than 300 psig), the valve(s)shall be ANSI Class flanged inlet connection andshall have a (steel, stainless steel, or ductile iron) body, top and inletflange.Standard operating pressure for Crispin Air Valves is 20 to 150PSIG. Please check one of the following if your operating needsdiffer: 2 to 40 PSIG151 to 300 PSIGMAX. PRESSURE DISCHARGE RATE40 PSIG12.6 SCFM50 PSIG9.6 SCFM85 PSIG8.3 SCFM150 PSIG6.1 SCFM200 PSIG4.5 SCFM300 PSIG3.2 SCFMSIZE 1011121329CP1CP2CP3CP4INLET SIZE1” NPT2” NPT2” 125# FLG2” 250# FLG3” NPT3” 125# FLG3” 250# FLGOUTLET SIZE1” NPT2” NPT2” NPT2” NPT3” NPT3” NPT3” S LIST FOR AIR & VACUUMDESCRIPTIONMATERIALASTMTOPCAST IRONA126 CL. BFLANGECAST IRONA126 CL. BBODYCAST IRONA126 CL. BGASKETARMSTRONG N-8092N/ASEATBUNA-N TSTEELA563PLUGBRASSB505INTERFERENCE PINSTAINLESS STEELA58EYE NUTFORGED STEELA563PARTS LIST FOR PRESSURE RELEASE UNITVALVE SEATSTAINLESS STEELA276PLUNGER BUTTONVITOND2000VALVE LEVERSTAINLESS STEELA240SCREW (DRIVE)STAINLESS STEELA193BALL FLOATSTAINLESS STEELA240HINGE PINSTAINLESS STEELA580HINGE BUTTSTAINLESS STEELA240BOLTSTEELA307SCREWSTAINLESS STEELA193FLANGECAST IRONA126 CL.BBODYCAST IRONA126 CL.BFLANGE GASKETARMSTRONG N-8092N/APLUG (NOT SHOWN)BRASSB505PARTS LIST FOR CONNECTING PARTSNIPPLESTEELA53NIPPLESTEELA53ELBOWMALLEABLE IRONA3381/2” GATE VALVEBRASSN/AAL/M Crispin Valve, 600 Fowler Ave., Berwick, PA 18603 1-800-AIR-VALV T: (570) 752-4524 F: (570) 752-4962 WWW.CRISPINVALVE.COM sales@crispinvalve.com
Submittal Sheet for Crispin AL/PL Series4”–10” Dual Body Combo. Air Release (1 of 2)Manufactured in compliance with ANSI/AWWA C5122 19A-171822A21222910137A-2139CP1C122085418 22613111S23 251N-1P241H105529186CP3CP1329SpecificationsThe combination air valve(s) shall be installed at highpoints in the system or at points selected by the engineer. This will permit discharging the surge of air froman empty line when filling and relieve the vacuum whenthe line is draining, or is under negative pressure. Thevalve(s) shall also release the accumulation of air whenthe system is under pressure.CP2SECTION A–A-Orifice OptionsDIAMETER MAX. PRES. DISCHARGE RATE5/16100 PSIG105 SCFM1/4150 PSIG98 SCFM3/16200 PSIG72 SCFM5/32250 PSIG61.1 SCFM1/8300 PSIG46.7 SCFMSIZE SPECIFICATIONSMODELINLET SIZEOUTLET SIZE*AL40/PL10 4” NPT4” NPT*AL41/PL10 4” 125# FLG4” NPT*AL42/PL10 4” 250# FLG4” NPTAL61/PL10 6” 125# NPT6” NPTAL62/PL10 6” 250# FLG6” NPTAL81/PL10 8” 125# FLG8” NPTAL82/PL10 8” 250# FLG8” NPTAL101/PL10 10” 125# FLG10” NPTAL102/PL10 10” 250# FLG10” NPT* 4” Valve also available with a 4” NPT .245359198221289319524574The Air and Vacuum Valve shall operate by sealing theBUNA-N rubber outlet seat with a peripherially guided floatas the liquid enters the valve chamber to raise the float. All Crispin Valves are hydrostatically tested at 150% of their maximum working pressure.The Pressure Valve shall operate through a compound lever system and shall have a ” orifice with valve sealing faces, ofan adjustable BUNA-N rubber valve and (stainless steel or PVC) and shall operate at PSIG and be capable of passingSCFM of air. Valves which use a needle valve to seal the orifice will not be acceptable.Valve construction shall be ” NPT screwed or ANSI Class (125,250) flanged inlet connection and shall be cast iron body, top,and inlet flange (where required), stainless steel float with bronze and (brass or stainless steel) trim. Refer to Air & Vacuum and Pressure AirRelease specifications for Valve description.The valve(s) shall be CRISPIN Model Dual Air Valve(s), Type N, (PVC seat and BUNA-N rubber valve) or Type P (stainlesssteel seat and BUNA-N rubber valve) pressure valve(s) as manufactured by Crispin-Multiplex Manufacturing Co., Berwick, Pa. The valve(s)shall include a Crispin Pressure Air Release Valve.Option: A protectop shall be supplied to prevent debris from entering the outlet of the Air and Vacuum Valve.SUBMITTAL SHEET FOR AL/PL SERIESADate: October, 2001Option: (Where pressures are greater than 300 psig), the valve(s) shall be ANSI Class flanged inlet connection and shall have a(steel, stainless steel, or ductile iron) body, top and inlet flange. Standard operating pressure for Crispin Air Valves is 20 to 150 PSIG. Pleasecheck one of the following if your operating needs differ: 2 to 40 PSIG151 to 300 PSIGCrispin Valve, 600 Fowler Ave., Berwick, PA 18603 1-800-AIR-VALV T: (570) 752-4524 F: (570) 752-4962 WWW.CRISPINVALVE.COM sales@crispinvalve.com AL/PL
Submittal Sheet for Crispin AL/PL Series4”–10” Dual Body Combo. Air Release (2 of 2)SUBMITTAL SHEET FOR AL/PL SERIESManufactured in compliance with ANSI/AWWA C512PARTS LIST FOR AIR & LUGLIFTING LUGMATERIALHRCQ STEELCAST IRONCAST IRONCAST IRONARMSTRONG N—8092BUNA—N RUBBERSTAINLESS STEELSTEELSTEELSTEELSTEELBRASSSTEELASTMN/AA126 CL.BA126 CL.BA126 CL.BN/AD2000A240A307A307A563A307B505A563PARTS LIST FOR PRESSURE RELEASE 29VALVE SEATVALVE SEATVALVE PLUNGERPLUNGER NUTLOCK WASHERVALVE FULCRUMVALVE LEVERLlNKBALL FULCRUMBALL FLOATBALL LEVERBEARING PINBEARING PINBEARING PINCOTTER PINBOLTNUTTOPFLANGEBODYFULCRUM WASHERFULCRUM WASHERSEAT GASKETFLANGE GASKETBOLTPLUGPVCSTAINLESS STEELBUNA—N RUBBER & S/SSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTAIN LESS STEELSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTEELSTEELCAST IRONCAST IRONCAST IRONFIBERFIBERBUNA—N RUBBERARMSTRONG N-8092STAINLESS 82A240A240A582A582A582A493A307A563A126 CL.BA126 CL.BA126 CL.BD710D710D2000N/AA193B505PARTS LIST FOR CONNECTING PARTSCP1CP2CP312Date: October, 2001NIPPLESTREET ELBOW1” GATE VALVESTEELMALLEABLE IRONBRASSA53A338N/A* Parts are interchangable and optional at customer’s request ** Optional at customer’s requestCrispin Valve, 600 Fowler Ave., Berwick, PA 18603 1-800-AIR-VALV T: (570) 752-4524 F: (570) 752-4962 WWW.CRISPINVALVE.COM sales@crispinvalve.com
Submittal Sheet for Crispin AL/PL Series12”–16” Dual Body Combo. Air Release (1 of 2)Manufactured in compliance with ANSI/AWWA C512Date: October, 200117A-2613292 19232211N-1P25 2622 22A20242F11 6 355711F18A- CP4945 81211FA3W5128 71510 13219CP4 CP3B29CP2CP1SECTION A–A-Orifice Options3FHDIAMETER MAX. PRES. DISCHARGE RATE3/8100 PSIG152 SCFM5/16150 PSIG152 SCFM1/4200 PSIG127 SCFM3/16250 PSIG88 SCFM5/32300 PSIG73 SCFM296SpecificationsThe Combination Air Valve(s) shall be installed at highpoints in the system or at points selected by the engineer. This will permit discharging the surge of air froman empty line when filling and relieve the vacuum whenthe line is draining, or is under negative pressure. Thevalve(s) shall also release the accumulation of air whenthe system is under pressure.SIZE L142/PL20AL161/PL20AL162/PL20INLET SIZE12” 125# FLG12” 250# FLG14” 125# FLG14” 250# FLG16” 125# FLG16” 250# FLGOUTLET SIZE12” NPT12” NPT14” NPT14” NPT16” NPT16” 537.5WHT.7758281023121011431326The Air and Vacuum Valve shall operate by sealing the BUNA-N rubber outlet seat with a peripherially guided float as the liquid enters the valvechamber to raise the float. All Crispin Valves are hydrostatically tested to 150% of their maximum working pressure.The Pressure Valve shall operate through a compound lever system and shall have a ” orifice with valve sealing faces, ofan adjustable BUNA-N rubber valve and (stainless steel or PVC) and shall operate at PSIG and be capable of passingSCFM of air. Valves which use a needle valve to seal the orifice will not be acceptable.Valve construction shall be ANSI Class (125,250) flanged inlet connection and shall be cast iron body, top, and inlet flange (whererequired), stainless steel float with bronze and (brass or stainless steel) trim. Refer to Air & Vacuum and Pressure Air Release specifications for Valve description.The valve(s) shall be CRISPIN Model Dual Air Valve(s), Type N, (PVC seat and BUNA-N rubber valve) or Type P (stainlesssteel seat and BUNA-N rubber valve) pressure valve(s) as manufactured by Crispin-Multiplex Manufacturing Co., Berwick, Pa. The valve(s)shall include a Crispin Pressure Air Release Valve.Option: A hood shall be supplied to prevent debris from entering the outlet of the Air and Vacuum Valve.SUBMITTAL SHEET FOR AL/PL SERIESAOption: (Where pressures are greater than 300 psig), the valve(s) shall be ANSI Class flanged inlet connection and shall have a(steel, stainless steel, or ductile iron) body, top and inlet flange.Standard operating pressure for Crispin Air Valves is 20 to 150 PSIG. Please check one of the following if your operating needs differ:2 to 40 PSIG151 to 300 PSIG13Crispin Valve, 600 Fowler Ave., Berwick, PA 18603 1-800-AIR-VALV T: (570) 752-4524 F: (570) 752-4962 WWW.CRISPINVALVE.COM sales@crispinvalve.com AL/PL
Submittal Sheet for Crispin AL/PL Series12”–16” Dual Body Combo. Air Release (2 of 2)SUBMITTAL SHEET FOR AL/P SERIESManufactured in compliance with ANSI/AWWA C51214AL/PLDate: October, 2001PARTS LIST FOR AIR & NHOODFLANGEBODYGASKETSEATFLOATFLOAT ROD GUIDESEAT BOLTSWASHERBOLTBOLTBOLTNUTPLUGLIFTING LUGVALVE SEATMATERIALHRCQ STEELCAST IRONCAST IRONARMSTRONG N—8092BUNA—N RUBBERSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTEELSTEELSTEELSTEELBRASSSTEELPVCASTMN/AA126 CL.BA126 401784PARTS LIST FOR PRESSURE RELEASE UNIT*1 P233W56789101112131517181920212222A2324252629VALVE SEATVALVE PLUNGERNUTLOCK WASHERVALVE FULCRUMVALVE LEVERLlNKBALL FULCRUMBALL FLOATBALL LEVERBEARING PINBEARING PINBEARING PINCOTTER PINBOLTNUTTOPFLANGEBODYFULCRUM WASHERFULCRUM WASHERSEAT GASKETFLANGE GASKETBOLTNUTPLUGSTAINLESS STEELBUNA—N RUBBER & S/SSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTAIN LESS STEELSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTEELSTEELCAST IRONCAST IRONCAST IRONFIBERFIBERBUNA—N RUBBERARMSTRONG N-8092STAINLESS 582A240A240A582A582A582A493A307A563A126 CL.BA126 CL.BA126 CL.BD710D710D2000N/AA193A563B50PARTS LIST FOR CONNECTING PARTSCP1NIPPLECP2ELBOWCP31” GATE VALVECP4NIPPLE** Optional at customer’s requestSTEELMALLEABLE IRONBRASSSTEEL* Parts are interchangable and optional at customer’s requestA53A338N/AA53Crispin Valve, 600 Fowler Ave., Berwick, PA 18603 1-800-AIR-VALV T: (570) 752-4524 F: (570) 752-4962 WWW.CRISPINVALVE.COM sales@crispinvalve.com
The valve(s) shall be CRISPIN Model _ Dual Air Valve(s), Type N, (PVC seat and BUNA-N rubber valve) or Type P (stainless steel seat and BUNA-N rubber valve) pressure valve(s) as manufactured by Crispin-Multi-plex Manufacturing Co., Berwick, Pa. The valve(s) shall include a File Size: 242KBPage Count: 7Explore furtherThe AL Series Air and Vacuum Valvescrispinvalve.comAlfa Laval SRC Divert Valve Parts Listwww.csidesigns.comAlfa Laval ARC Divert Valve Parts List - csidesigns.comwww.csidesigns.comAlfa Laval - Double Seat Valves or Mixproof Valveswww.alfalaval.com4-WAY VALVES 1/4”, 3/8” & 1/2” - Allenairwww.allenair.comRecommended to you b
Precision Air 2355 air cart with Precision Disk 500 drill. Precision Air 2355 air cart with row crop tires attached to Nutri-Tiller 955. Precision Air 3555 air cart. Precision Air 4765 air cart. Precision Air 4585 air cart. Precision Air 4955 cart. THE LINEUP OF PRECISION AIR 5 SERIES AIR CARTS INCLUDES: Seven models with tank sizes ranging from
SMB_Dual Port, SMB_Cable assembly, Waterproof Cap RF Connector 1.6/5.6 Series,1.0/2.3 Series, 7/16 Series SMA Series, SMB Series, SMC Series, BT43 Series FME Series, MCX Series, MMCX Series, N Series TNC Series, UHF Series, MINI UHF Series SSMB Series, F Series, SMP Series, Reverse Polarity
Avionics: Honeywell 6-Tube EFIS. Enrolled on Honeywell HAPP. Dual Honeywell SPZ-8400 Digital Auto Pilot Dual Honeywell FZ-820 Flight Guidance Computers Dual Honeywell NZ-2010 LR NAV/FMS w/ 6.1 Software Dual Collins VHF-422B COMM (8.33 Spacing) Dual Collins VIR-432 NAV w/ FM Immunity Dual Collins ADF-462 Dual Collins DME-442
1.2.7 Dual monitor set-up screen*9) This page is concerning the dual monitor usage. Use the dual monitor function Check here when you wish to use dual monitor function. OS management dual monitor Select whether it is OS management dual monitor or video card management dual monitor. It is
58 AIR FORCE Magazine / May 2016 Acronyms & Abbreviations AABactivated 1935. Named for Lt. Col. Frederick I. Eglin, Army Air Base AAFRG (ANG), RPA operations; 309th Aerospace Army Airfield AB Air Base ABG Air Base Group ABW Air Base Wing ACC Air Combat Command ACG Air Control Group ACS Air Control Squadron ACTS Air Combat Training Squadron ACWHistory: Air Control Wing
be connected to an extended duration air supply hose line to supply breathing air to the respirator user. The DUAL EBSS accessory hose is available on the SCOTT AIR-PAK 75, AIR-PAK NxG, and AIR-PAK X3 series SCBA. Breathing support may be provided one of two ways with the DUAL EBSS hose.
Dual Port Cylinder Covers Can be used on all 1600 based dual port engines. This is the clean way to move on up to dual port cylinder heads. 1988 Dual Port Cylinder Covers - Black (set of 2) 1993 Dual Port Cylinder Covers - Chrome (set of 2) Deflector Plates Stock Factory Deflector Plates are used on all Type-1, 2 & 3 VW engines. They are .
dis. cod. descrizione description 1 s/149/06 listello portabr p90-p90b-p906 burners holder for p90-p90b-p90_6 2 a/434/04 portainiett a gomito grill/fuochi injector holder grill/cooktop 3 a/434/06 portainiett bruc aux dual dual burner injector holder 4 a/066/10 farfalla reg bruciat aux dual dual burner regul valve 5 a/014/23 bruciatore (venturi) aux dual small dual burner
