Suzuki Manual Master - Duitman Hengelo
COPYRIGHT 2009SUZUKIUNLOCKINGTECHNOLOGYVERSION 2.8 JULY 2011Copyright 2011
COPYRIGHT 2009SUZUKI - CONTENTSPAGEAPPLICATIONSADS109ADS1622SUZUKI (Non CAN)SUZUKI CAN/PROXIMITY34DIAGNOSTIC SOCKETS LOCATIONS5SPECIAL FUNCTIONSSUZUKI KEY PROGRAMMINGSUZUKI CAN/PROX KEY PROGRAMMING6-78-9TIPS & HINTS10REMOTE CONTROL PROGRAMMING11 - 12VERSION 2.8 JULY 2011Copyright 2011
COPYRIGHT 2009APPLICATIONSSUZUKI - ADS109PRO12343AD100ALTOALL ADC151DADC128BALENOALL ADC151DADC128CARRY 1.3ALL ADC151DADC128GRAND VITARAALL ADC151DADC128XL7ALL ADC151DADC128IGNISALL ADC151DADC128JIMNYALL ADC151DADC128LIANAALL ADC151DADC128SAMURAIALL ADC151DADC128SWIFT 2005 ADC151DADC128VITARAALL ADC151DADC128WAGON-RALL ADC151AADC110-BX-90ALL ADC151DADC128VERSION 2.8 JULY 2011Copyright 2011
COPYRIGHT 2009APPLICATIONSSUZUKI CAN/PROXIMITY - ADS162*PRO1234SWIFT (CAN)ZC11S2005 ADC151A SWIFT (PROX)ZC21S / ZC31S2005 ADC151A TRACKER2005 ADC151A AZTEK2005 ADC151A SX4 (CAN)2005 ADC151A SPLASH (CAN)2005 ADC151A * PRO ONLY4AD100VERSION 2.8 JULY 2011Copyright 2011
COPYRIGHT 2009DIAGNOSTIC SOCKET LOCATIONSSUZUKIBALENOIGNISJIMNYVITARASWIFTWagon R5ALTONEW SWIFTCARRYSX4VERSION 2.8 JULY 2011Copyright 2011
COPYRIGHT 2009SPECIAL FUNCTIONSSUZUKI (Non CAN)KEY PROGRAMMINGVEHICLE SELECTIONKEYS PROGRAMMED ALTOIMPORTANTKEYS PROGRAMMED: 2 BALENOWHEN INSTRUCTED ENSURE THETESTER IS TURNED OFF ANDDISCONNECTED FROM THE VEHICLE BALENO DHW GRAND VITARA GRAND VITARA XL-7PRESS ENTER KEY IGNISDIAGNOSTIC MENU CLEAR KEYSSWITCH IGNITION ONPROGRAM KEYSKEYS PROGRAMMEDRESETEACH KEY NEEDS TO BEPROGRAMMED INDIVIDUALLY.THIS PROCEDURE NEEDS TO BEREPEATED FOR EACH KEY.AFTER ALL KEYS PROGRAMMED,SWITCH IGNITION OFF,DISCONNNECT TESTER AND CYCLEALL KEYS (DO NOT START ENGINE)MAX 4 KEYSPRESS ENTER KEYPRESS ENTER KEYECU IDENTIFICATIONDIAGNOSTIC MENUCLEAR KEYS ONLT NEEDS TO BEPERFORMED IF YOU WANT TODELETE ALL EXISTING KEYS.SUZUKIIF YOU ONLY WANT TO ADD A KEYTHEN GO TO ‘PROGRAM KEY’ MENUSELECTION.PRESS ENTER KEYDIAGNOSTIC MENUECU IDENTIFICATIONCLEAR KEYSPROGRAM KEYS KEYS PROGRAMMEDRESETPRESS ENTER KEYCLEAR KEYSSWITCH IGNITION OFFSECURITY ACCESSACCESS GAINEDFAULT CODES SPECIAL FUNCTIONSPRESS ENTER KEYPRESS ENTER KEYDIAGNOSTIC MENUCLEAR KEYSPROGRAM KEYSPLEASE WAITELAPSED TIME: 02PLEASE WAIT02CLEAR KEYSPROGRAM KEYSPROCEDURE COMPLETEPROCEDURE COMPLETESWITCH IGNITION OFFSWITCH IGNITION OFFDISCONNECT TESTERFROM VEHICLEDISCONNECT TESTERFROM VEHICLECLEAR KEYSPROGRAM KEYS KEYS PROGRAMMEDRESETPRESS ENTER KEYSECURITY ACCESSACCESS GAINED6VERSION 2.8 JULY 2011Copyright 2011
COPYRIGHT 2009SPECIAL FUNCTIONSSUZUKI (Non CAN)RESETON CERTAIN VEHICLES IF THEBATTERY HAS BEEN DISCONNECTEDOR GONE FLAT THE KEYS WILL NOTWORK or THE IMMO LIGHT ISFLASHING AFTER KEYPROGRAMMINGTHEN USE THE RESET FUNCTION.REMOTE PROGRAMMINGPROGRAMMING REMOTES IS AMANUAL PROCEDURE.PLEASE REFER TO REMOTEPROGRAMMING SECTIONDIAGNOSTIC MENUCLEAR KEYSPROGRAM KEYSKEYS PROGRAMMED RESETPRESS ENTER KEYRESETDATE RECORDEDPRESS ENTER KEYRESETPROCEDURE COMPLETEPRESS ENTER KEY7VERSION 2.8 JULY 2011Copyright 2011
COPYRIGHT 2009SPECIAL FUNCTIONSSUZUKI CAN/PROXKEY PROGRAMMINGVEHICLE SELECTIONDIAGNOSTIC MENUENTER MONTH KEYS STORED IGNISPROGRAM KEYS JIMNY LIANA SAMURAI1234567890 SWIFT VITARAVEHICLE SELECTIONKEYS PROGRAMMEDWEB SECURITYKEYS STORED: 0308 20052005 2008 PROXIMITYXL7PRESS ENTER KEY DIAGNOSTIC MENUENTER YEARKEYS STOREDREMOVE MECHANICAL KEY FROMFOB.INSERT THE MECHANICAL KEY ANDTURN ON WHEN INSTRUCTED.SWITCH IGNITION ON PROGRAM KEYS1234567890CLEAR KEYSWEB SECURITYALL KEYS WILLBE CLEARED2008CONTINUEYES ENTERNO BACKPRESS ENTER KEY ECU IDENTIFICATIONPROGRAM KEYSPROGRAM KEYSSUZUKI SWIFTPLEASE ENSUREPLEASE WAITIGNITION ON02WITH VALID KEYPRESS ENTER KEYPRESS ENTER KEYDIAGNOSTIC MENUPROGRAM KEYSPROGRAM KEYSCLEAR KEYSPLEASE WAITSUCCESS10ECU IDENTIFICATION SPECIAL FUNCTIONSPRESS ENTER KEY8VERSION 2.8 JULY 2011PRESS ENTER KEYCopyright 2011
COPYRIGHT 2009SPECIAL FUNCTIONSSUZUKI CAN/PROXKEY PROGRAMMINGREMOTE PROGRAMMINGPROGRAM KEYSPROGRAM KEYSKEY PROGRAMMEDKEY PROGRAMMEDPROGRAMPROGRAMNEXT KEYYES ENTERNO BACKPRESS ENTER KEYNEXT KEYYES ENTERNO BACKPRESS ENTER KEYREPEAT THE PROCEDURE FORPROGRAMMING MORE KEYS.REMOVE KEY FROM IGNITION.INSERT THE NEXT MECHANICAL KEYAND TURN ON WHEN INSTRUCTED.MAX 4 KEYSPROGRAM KEYSTURN IGNITION ONWITH NEXT KEYAND PRESS ENTERPROGRAM KEYSPLEASE WAIT02PROGRAM KEYSPLEASE WAIT10PLEASE WAITTRYING TO COMMUNICATE9VERSION 2.8 JULY 2011Copyright 2011PROGRAMMING REMOTES IS AMANUAL PROCEDURE.PLEASE REFER TO REMOTEPROGRAMMING SECTION
COPYRIGHT 2009TIPS & HINTSSUZUKI (NON CAN)1.Up to 5 keys can be "registered"2.You will receive the "fail" message if you try to program an existing key that is already stored within theImmobiliser control unit.3.The immobiliser control unit is located around the key barrel and uses 2 fused feeds, one directly from the fusebox and one indirectly from the engine control unit.4.Communication is on pins 7 (blue) and 9 (Yellow) of the diagnostic socket (engine and immobiliser)5.There are two earth points for the immobiliser circuit (pin 4 of the immobiliser control unit, splits into twowires) and they are on the steering column support and in the O/S kick panel.6.If your get an ERROR message during programming, this can be caused by the number of keys alreadyprogrammed being the maximum allowed (5 is maximum). Clear the existing keys before programming the new keyswill overcome this.SUZUKI CAN/PROX1.2.3.Up to 4 keys can be "registered"The remotes need to be programmed manually.At the end of the procedure start the vehicles using the actual key to complete the programming procedureSUZUKI SX4If remote controller or keyless start control module is replaced with a new one or additional remote controller isnecessary, register ID code(s) of remote controller.1)2)3)4)Sit in driver seat and close all doors.Check that door lock of driver seat is unlocked.Insert ignition key (1) into ignition key cylinder.Perform Steps (a) through (f) described blow within 25 seconds after Step (3).a) First push manual door lock switch toward lock side and then push it toward unlock side.b) Repeat Step a) 2 more times.c) Push lock side of manual door lock switch.d) Remove ignition key from ignition key cylinder once and then insert it again.e) Repeat Step d) 3 more times.f) Start engine and wait for 3 seconds.5) Turn ignition switch to OFF position.When ignition switch is turned to OFF position, buzzer sounds twice and door lock is activated from lock position tounlock position. This operation indicates that keyless start control module has entered registration mode.6) Push lock or unlock button of remote controller within 30 seconds after Step 5) to be registered.When lock or unlock button of remote controller is pushed, buzzer sounds twice, door lock is activated to lock positionand then to unlock position. This operation indicates that remote controller ID code has been registered in keylessstart control module. If an additional remote controller needs to be registered, repeat the procedure of Step 6) within30 seconds after Step 5).7) To end registration mode, remove ignition key from ignition key cylinder or turn it to ON position.In case of vehicle equipped with immobilizer control system, if engine start function of keyless start system does notwork after registration, check ECM if DTC P1615 is detected. If it is detected, go to DTC P1615: Steering Lock UnitCommunication Error. If it is not detected, perform registration procedure again.10VERSION 2.8 JULY 2011Copyright 2011
COPYRIGHT 2009REMOTE PROGRAMMINGSUZUKI (NON CAN)VITARAProcedure1.Switch ignition OFF and close all doors.2.Open drivers door and switch ignition on3.Switch ignition OFF4.Press and release drivers door ajar switch 3 times5.Switch ignition ON and then OFF6.Press and hold each button of the remote in turn for 5 seconds each7.Central locking should activate8.Press remote control lock button9.Maximum of 2 remotes possibleAERIOGRAND VITARAXL-7If a remote or BCM (included in junction block assembly) is replaced with a new one oradditional remote(s) is necessary, program remote code(s).Procedure1.Confirm that all doors are closed and ignition key is out of ignition key cylinder.2.Open driver side door.3.Turn ignition switch to ON position, and then remove ignition key from ignition keycylinder within 10 seconds after that.4.Push and release driver side door switch (1) at 3 times by hand within 20 seconds after removing ignition keyfrom ignition key cylinder.5.Turn ignition switch to ON position, and then drawn ignition key from ignition key cylinder within 10 secondsafter that. All doors automatically lock and unlock once. With this, registration mode.6.Push “UNLOCK” button (2) on transmitter (3) within 20 seconds after Step 5. All doors automatically lock andunlock once. With this, code registration is completed.7.11If an additional transmitter, needs to be programmed repeat the procedure of Step 1.VERSION 2.8 JULY 2011Copyright 2011
COPYRIGHT 2009REMOTE PROGRAMMINGIGNISProcedure1.Confirm that IG switch is OFF position.2.Remove DOOR LOCK fuse and install it again.3.Press the button on the remote one time toward the receiver within 30 sec4.If two transmitters are registered, repeat step 1) to 3) with other remotesNotes: a.Two transmitter codes can be registered.b.When a 3rd/new remote is registered, the oldest one will be cleared.SUZUKI Can/PROXSWIFT (RS413 and RS415)Procedure1 Sit in driver’s seat, close all doors, all doors unlocked.2 Insert ignition key (emergency blade) into ignition3 Press door locking switch (in the driver’s door panel) to lock4 Press door locking switch (in the driver’s door panel) to unlock5 Press door locking switch (in the driver’s door panel) to lock6 Press door locking switch (in the driver’s door panel) to unlock7 Press door locking switch (in the driver’s door panel) to lock8 Press door locking switch (in the driver’s door panel) to unlock9 Press door locking switch (in the driver’s door panel) to lock10 Remove the key from ignition11 Insert key in ignition12 Remove the key from ignition13 Insert key in ignition14 Remove the key from ignition15 Insert key in ignition16 Remove the key from ignition17 Insert key in ignition18 Start engine and wait for 3 seconds19 Turn the ignition OFF20 Buzzer sounds and door locks are activated21 Press a button on the remote - a buzzer will sound and the doors will lock and unlock22 Doors will lock and unlock23 Turn ignition ON12VERSION 2.8 JULY 2011Copyright 2011
COPYRIGHT 200913VERSION 2.8 JULY 2011Copyright 2011
COPYRIGHT 2009Advanced Diagnostics LtdDiagnostics HouseEastboro FieldsHemdaleNuneatonCV11 6GLT: 44(0)2476 347000F: 44(0)2476 347100W: www.advanced-diagnostics.co.uk14VERSION 2.8 JULY 2011Copyright 2011
1. Up to 4 keys can be "registered" 2. The remotes need to be programmed manually. 3. At the end of the procedure start the vehicles using the actual key to complete the programming procedure SUZUKI SX4 If remote controller or keyless start control module is replaced with a new one or additional remote controller is
SUZUKI SUZUKI Years Hybrid SYSTEM #105590 SUZUKI 250 2x4 ‘97-01 N/D SUZUKI 280 King Quad ‘98 & Older N/D SUZUKI 300 King Quad ‘99-01 N/D SUZUKI 400 Eiger 2x4, 4x4 ‘02-07 N/D SUZUKI 400 King Quad 4x4/AS/AF/ASi/AFi ‘08-18 Yes SUZUKI 450 King Quad 4x4/AXi ‘07-10 Yes SUZUKI 500 King Quad AXI ‘09-18 Yes SUZ
2015 suzuki king quad (lt-a400asi) tr 2016 suzuki king quad (lt-a400asi) tr 2017 suzuki king quad (lt-a400fsi) tr 2004 suzuki quad sport (lt-z400) tr 2005 suzuki quad sport (lt-z400) nt 2006 suzuki quad sport (lt-z400) nt 2007 suzuki quad sport (lt-z400) nt 2008 suzuki quad sport (lt-z400) nt 2009 suzuki quad
Suzuki Violin Books & CD's Suzuki Piano Accompaniment Books (for violin) Suzuki violin MIDI disks Suzuki Association of the Americas International Suzuki Society pdf: Suzuki Violin Repertoire List Books by & about Dr. Suzuki Agopian, Edmond: The no time to practice technique companion ASTA String Syllabus 2003 Bachman, A.: Encyclopedia of Violin
MIC Suzuki flute teacher Meret Bitticks was a guest clinician for the Suzuki Association of Minnesota’s workshop in November. MIC Suzuki cello teacher Tanya Carey taught a Suzuki Book 2 teacher training course in Houston, Texas on January 1-5, 2020. List of December Suzuki Sunday performers Piano jamboree:
The Suzuki Service Portal Site provides information for maintenance, diagnosis and repair of Suzuki automobiles to authorized Suzuki workshops and independent workshops. It contains the following types of documents: Manuals: Here you will be able to find the official Workshop Manuals and Supplements for Suzuki Automobiles.
SUZUKI MOTORCYCLE 2018 2018 SUZUKI MOTORCYCLE FULL LINE UP Suzuki’s “Way of Life!” is the heart of . Read your Owner’s Manual carefully. . CRUISER BOULEVARD M109R P28BOULEVARD M90 BOULEVARD M50 BOULEVARD C90 P29 BOULEVARD C50 P30BOULEVARD S40 .
pajero io all . procedure in the manual and follow the steps indicated. leave the tetser connected erase/reprog remotes remote 1 programmed back to exit press enter key note : the tester will indicate when each remote is programmed by
1 AWWA MANUAL M41 Chapter 1 General Information and History This manual provides the user with both technical and general information to aid in the design, specification, procurement, installation, and understanding of ductile-iron pipe.
