QUESTION - Kitec.vecv-skillcomp
Category: TRUCKRound: Round 2Note: Question may have ONE OR MORE alternatives as correctR2T01QUESTIONModel/Variant: FH (4),6*4, RADD-G2, RSS-AIRAs per the image, which among the statements is/are correct regarding component AA.B.C.D.2-way solenoid air pilot valve3-way solenoid air pilot valve2-way solenoid electrical pilot valve3-way solenoid electrical pilot valveReference: Impact identity :135467887Sme: Sumesh KrishnanR2T02QUESTIONModel/Variant: FM (4)Which of the below statement is/are correct as per the given imageA.B.C.D.In A, the resistance should be approx. 35 10 Ώ for a 24-volt solenoid.In C, Orifice shall be used together with F1-25The length of Spring (2) should be approx. 55mmOrifice (C), should not be reusedReference: Impact Id 136971245Sme: Sumesh Krishnan
R2T03QUESTIONModel/Variant: FM (4)The pass-through holes in the cab roof are provided with rubber grommets,part number20442926.How may wires can pass through the grommetA.B.C.D.1357Reference: YVD-VBI-FM-4 - Electricity-Wiring - page no :9Sme: Sumesh KrishnanR2T04QUESTIONModel/Variant: FM (4) CHH-LOWWhat is the rear axle tire compensation for load above 12000kg?A.B.C.D.16 mm24 mm8 mm31 mmReference: Impact identity 143581197Sme: Sumesh KrishnanR2T05QUESTIONModel/Variant: GeneralWhat is the Abbreviation of WIS?A.B.C.D.Weight Information SystemWork Information SystemWork Infotainment SystemWalsh Information SystemReference: YVD -Portal -system information-WISSme: Praveen Kumar
R2T06QUESTIONModel/Variant: FM (4) Euro 4As per P1E5N, the indicated voltage value is 12V. How many number of radiators aremounted?A.B.C.D.1234Reference : Tech tool - test - 17037-3 sensor and parameter values monitoringSme: Sumesh KrishnanR2T07QUESTIONModel/Variant: FM (4)Which among below components are pyrotechnicalA.B.C.D.Bi stable relaySeat belt pre tensionerAir BagBattery SensorReference: FM (4) wiring diagram- Wiring diagram page PE-SRS, Supplementary RestrainSystem, airbagSme: Sumesh KrishnanR2T08QUESTIONModel/Variant: FM (4)What is the filter element rating of return line filter (Hypratek wet kit)?A.B.C.D.15 µ20 µ25 µ10 µReference: YVD- Yellow Binder Hypratek wet kit docSme: Jacob Mathew
R2T09QUESTIONModel/Variant: FM (4)Driver Information Display shows warning - Take a break! what does it meanA.B.C.D.When the driver shows signs of less attentionWhen the performance is not improved within a set timeWhen vehicle has been driven more distance than which is set in trip dataWhen EDP determines, driver needs a break on account of safetyReference : Impact identity : 143011382Sme: Sumesh KrishnanR2T10QUESTIONModel/Variant: FM (4)For a FM (4) truck reported with engine complaint of abnormal noise from engine @ 15000Ehrs. On investigation observed main and connecting rod bearings worn out completelywith symptoms of heat caused by insufficient lubrication. Engine oil (VDS 4, 15W40) samplecollected and was tested as a part of basic investigation. Results of parameters tested areFe 60 ppm, Pb 20 ppm, Cr 4 ppm, Viscosity 12.3 cst, Fuel 4%.Analyse the test results using standards and identify which of the following options arecorrect.A. Fe, Pb, Cr, Viscosity & Fuel % are within acceptable limitsB. Fe, Pb & Fuel dilution are beyond acceptable limits, Cr is within acceptable limits,Viscosity is below acceptable limits.C. Fe & Pb are within acceptable limits, Viscosity is below acceptable limits, Cr &Fuel dilution are beyond acceptable limitsD. Fe, Pb & Cr are within acceptable limits, Viscosity is below acceptable limits, Fueldilution is beyond acceptable limit.Reference: Impact / Service tab/ Design Description and function /17 Lubricant, fluids and oilanalysis/ Service and maintenance.Correct limits: Fe 100ppm, Pb 20 ppm, Cr 5ppm, Viscosity 12.5 16.3, Fuel 3%Sme: Madhu Kiran
R2T11QUESTIONModel/Variant: FMx 460One of the customer using FM (4) Euro IV truck (D13A) had approached ourworkshop asking whether Bio-diesel can be used in our trucks, which of the followingstatements are correct.A. Fuel containing below 7% FAME can be used in customer truck without anyspecific service requirements.B. Fuel containing more than 30% FAME is allowed in Euro IV engines withsome specific service requirements.C. The SCR muffler must be replaced after 100000 km. Interval might also depend onvehicle usage and fuel quality and a SCR muffler change can also be triggered byan after treatment fault code.D. Before starting usage of Bio-diesel in current truck an aftermarket kit PN21509751 to be usedReference: Impact / Service tab/ Description, Design and function /170 Bio-Diesel,general, YVD/ Truck accessories/ Driveline Equipment/ Bio-Diesel B30Sme:Madhu KiranR2T12QUESTIONModel/Variant: FM 6 4 T, D13A 440, FAA10, Fitted with DISC WHEEL,8.5" X 20"8-940266 truck reported to workshop after meeting with front accident, steering gearbox,front axle is completely damaged (nothing can be reused). Select which of the followingoptions are correct with respect to turning angle adjustment.A. Inner wheel angles 41.5 , Outer wheel angle32.5 Stopper Bolts washers 5no’s, Spacer Sleeve “Nil”, Extra washers 1no.Permitted clearance, front stop screw- 0.5 0.5mm. Permitted clearance, rear stop screw- ZeroclearanceB. Inner wheel angles 44 , Outer wheel angle 34 Stopper Bolts washers 4no’s, Sleeve “Nil, Extra washers 1no.Permitted clearance, front stop screw- 0.5 0.5mm. Permitted clearance, rear stop screw- ZeroclearanceC. Inner wheel angles 49 , Outer wheel angle 34.5 Stopper Bolts washers 2no’s, Spacer Sleeve “Nil”, Extrawashers “Nil” Permitted clearance, front stop screw- 0.5 0.5mm.Permitted clearance, rear stop screw- Zero clearanceD. Inner wheel angles 34 , Outer wheel angle 28 Stopper Bolts washers 2no’s, Spacer Sleeve 1no, Extra washers “Nil”.Permitted clearance, front stop screw- 0.5 0.5mm. Permitted clearance, rear stop screw- Zeroclearance
Reference: Impact / Service tab/ Specifications /6 Wheel suspension and steering/ Wheelalignment,YVD/ VDA/ Vehicle Information card- Check the steering specificationsWTD-D335/ WTDF20/ TF12/ FAT-RIG/ ACKMAN 5/ FA-HIGH/ RC-ROUGH.Sme: Madhu KiranR2T13QUESTIONModel/Variant: FE (3), S1051746Customer bought vehicle to workshop for complaint of excessive engine oil consumption.What are the probable causes need to be check with respect to this complaint?A. Air compressor is pumping lubricating oil into the airsystem. Turbocharger waste gate is malfunctioning, ifequipped. Lubricating oil filter is not correct.Engine control module (ECM) is malfunctioning.B. Cylinder head valve guides are excessivelyworn.Valve stem clearance is excessive or the valve stem seals aredamaged. Engine angularity during operation exceedsspecification.Air compressor is pumping lubricating oil into the air system.C. Valve stem clearance is excessive or the valve stem seals aredamaged. Lubricating oil filter is not correct.Lubricating oil pump ismalfunctioning. Vibration damper isdamaged or loose.D. Drivetrain is not correctly matched to the engine.Lubricating oil suction or transfer tube is loose or broken, or the gasket or o-ringsare leaking Cylinder head valve guides are excessively worn.Lubricating oil pump is malfunctioning.Reference : Impact identity 135667618Sme: Abdul ShukoorR2T14QUESTIONModel/Variant: FM (4)What are the types of batteries available in DESSA.B.C.D.Enhanced flooded batteryStandard flooded batterStarter batteryGEL batteryReference : Impact Identity 144512686Sme: Sumesh Krishnan
R2T15QUESTIONModel/Variant: FM (4)What is the maximum wear gap allowed for cradle bush of a tipping cylinder (MK Body)A.B.C.D.1.2mm1.5mm2.0mm2.5mmReference : PM-service scheduled for FM ( 4)Sme: Jacob MathewR2T16QUESTIONModel/Variant: FM (4) 8-957977Which of the following statements are true with respect to starting gear in an I-shift truck?A. If the truck is stopped with a non-permitted starting gear engaged in the M mode,then the starting gear is automatically selected.B. If the truck is approaching crest or hill in A mode, move the lever position to M forselecting the lowest possible starting gear.C. The choice of starting gear is reset to the original settings when truck is driven inthe high range area (from gear 7 onwards)D. The performance program generally provides higher engine speed than theeconomy program and a lower starting gear is selected.Reference: YVD / Drivers handbook / Driver Handbook Online/ Driver DigitalHandbook/ Volvo FMX/ Select Model, chassis No, E-mail and send/ PDF link will besent to e-mail/ Open handbook / PG 102, 103, 104.Sme: Madhu KiranR2T17QUESTIONModel/Variant: B9RWhich among the below statement/s is /are correct with respect to sealing of jointsA.B.C.D.Non-welded joints and gaps should be sealedThe sealing should take place after primingUse only dextroit 450 sealantThe priming should take place after sealingReference : Impact identity 53220307Sme: Sumesh Krishnan
R2T18QUESTIONModel/Variant: B9RWhat should be the push in depth of a pipe with diameter 4mmA.B.C.D.25.2mm20.5mm19.5mm17.2mmReference : Impact identity 121792156Sme: Sumesh KrishnanR2T19QUESTIONModel/Variant: B11R-188777Identify correct statements related to B11R-188777 bus with D11C engine.A.B.C.D.There will be 40% torque reduction with SCR system faultThe bus is WITHOUT GANGWAY LIGHTThe diameter of steering wheel is 450mmThe vehicle is equipped with data log mode in the displayReference: YVD - VariantsSme:Senthil KumarR2T20QUESTIONModel/Variant: B7R, D7EWhich of the below statement is/ are true regarding the start engine (K7) relay operationin B7R busA.B.C.D.Maximum current supplied to the Pin No 30 of relay is limited to 10AIf Start enable switch is in OFF condition, then the relay coil will not get supplyThe relay coil is controlled by engine ECU through a LDO signalRelay 87 Pin is connected to K65 relay through VIC MID couplerReference: Wiring diagram of B7R for the given chassis idSme: Rajendra Padiyar
R2T21QUESTIONModel/Variant: B8R (3)Which signal indicates whether it is the engine or retarder that is currently generating,limiting or determining the torque in Data link SAE J1939A.B.C.D.VP2EEC1CCVSTSC1Reference : Impact identity 134165532Sme:Sumesh KrishnanR2T22QUESTIONModel/Variant: GeneralWhat is the part number for Volvo FCI rence : YVD - system information tab-tech tool-information-Getac accessoriescatelogue-ENG-page 31Sme : Sumesh KrishnanR2T23QUESTIONModel/Variant: 8-823451What is the Cabin Colour of the truck which was assembled at the factory in1998 - Chassis no 8-823451.A.B.C.D.Lemon YellowSilver WhiteScarlet RedWinter WhiteReference: YVD- Impact search -Components-fg-8-Additional Vehicle InfoSme: Praveen kumar
R2T24QUESTIONModel/Variant: FH (4)When changing APM 1PRV (assembly P/N 22242663 (ECU P/N 21904205)) to APM 2PRV(assembly P/N 22358797 (ECU P/N 22341588)).Which among the below statement/s is/are correctA.B.C.D.Above change is not allowed as per DIN standardIf any fault code related to EBS system is generated, then reprogram EBS ECUHave to run conversion kit P/N 85142842 as accessory kit using the diagnostics toolMay need to perform lateral acceleration sensor calibrationReference: TPI 561-033 (impact identity 143321638)Sme: Sumesh KrishnanR2T25QUESTIONModel/Variant: FH (4)Add washer 994861 between oil cooler and brackets to increase distance to ---------------A.B.C.D.TransmissionCompressorTurbo chargerRadiatorReference: Impact identity 143995810 TPI 491-010, RadiatorSme: Sumesh KrishnanR2T26QUESTIONModel/Variant: FM 7What is the Type of Range Gear Shifting Rod used on FM7 truck Chassis no 8-828866A.B.C.D.GSS-RGSS-AGSHYDTRANGSS-SRReference : YVD-VDA-Vehicle variantSme:Praveen Kumar
R2T27QUESTIONModel/Variant: GeneralA warranty claim is registered with UDS pump as the causal part. There is proofavailable in the Product History Viewer that GD was used to diagnose this failure for thatchassis.A.B.C.D.VST 17906 and 17010 both to be claimed under labour tab in UCHPVST 17010 and 19010 both to be claimed under labour tab in UCHPVST 17906 to be claimed under labour tab in UCHPVST 19010 and 17906 to be claimed under labour tab in UCHPReference : WB 1.4.4,1.4.6VST 17906: Guided Diagnostic (GD) to trace the fault.VST 17010: Connection and Disconnection of VTTVST 19010: For repairs where a Warranty Protocol is mandatoryHere from the question it is clear that GD was performed (17906). 17010 is part of 17906.Hence 1 is wrong. When GD is performed for UDS pump, protocol is not required; hence theWS cannot claim 19010. Hence 2 & 4 are incorrect. Only 17906 is correct.Sme: Richard BabuR2T28QUESTIONModel/Variant: GeneralWhich is the most important supporting document to avail 2 year fitted parts warranty?A.B.C.D.Proof of part purchase from an authorised Volvo service centreGuarantee from customer that part fitment is as per Volvo standardsDocument specifying technician to truck ration of 1:15 for trucks and 1:12 for busesA PC ‘0’ labour invoice for fitment of the spare part against the specific ChassisReference: WB 1.2.4Sme:Richard BabuR2T29QUESTIONModel/Variant: GeneralWhat are the minimum requirements of a Branded area in a Volvo dealership?A. Each Volvo Group brand represented at the dealership hasits own branded area, dedicated to promoting its values and offeringsB. Only magazines and brochures for external use are provided – not internalpublications.C. Offers and promotions are adapted to the current season and campaigns.D. Each branded area is tidy and inviting.
Reference: YVD portal -Retail Development-customer experience from highway tohandshake-from highway to handshake bookletSme : Sumesh KrishnanR2T30QUESTIONModel/Variant: GeneralEnvironmental care has been a core value for Volvo Trucks since the 70’s.Since then, Volvo have reduced the emission of air pollutants from Volvo trucks by up to .and CO2 emissions by .A. 85% and 35 %B. 90% and 40%C. 93% and 45%D. 95 % and 50%Reference: YDV portal- Parts product-Heavy Facts-Volvo exchange parts-clutch, exchangeSme:Sumesh KrishnanR2T31QUESTIONModel/Variant: GeneralA Truck broke down at site on 20-Jan-19 10:00 Hrs, upon checking the truck, the technicianfound that the 3rd axle differential failed. The differential was sent to workshop for repair on20-Jan-19 17:00 Hrs and a repair estimate was submitted to Customer on 22-Jan-19 14:00hrs for approval. As some of the parts was not available at workshop, the same wasordered at PDC on 22-Jan-19 16:00 Hrs. Parts & Customer approval are awaited. Thisinformation need to be entered by the site technician in the Uptime App. Select the correctstatement / statements about this scenarioA. Job Type is Aggregate Repair & Job comments should be Differential failure. EnterJob start time as 20-Jan-19 10:00B. Once the break down is entered in App and the data is Synchronized, Status thisparticular repair can be monitored by Area Engineer, ASM, RSM & HO teamthrough the Uptime Web portalC. Open a Delay reason, with the category of “Volvo – Repair at Workshop”, enter starttime as20-Jan-19 17:00Open a Delay reason, with the category of “Customer – Approval / PO”, enter starttime as 22-Jan-19 14:00Open a Delay reason, with the category of “Volvo – Parts not available”, enter starttime as 22-Jan-19 16:00D. Open a Delay reason, with the category of “Volvo – Repair at Workshop”, enter starttime as20-Jan-19 17:00. And enter End time as 22-Jan-19 14:00Reference: CD Portal-Volvo uptime centre-self-study-session informationSme:Bala Dhandapani
R2T32QUESTIONModel/Variant: FM (4) I shiftA pre-warning alert is created for a vehicle in VOSP portal, if the estimated remainingclutch wear is less thanA.B.C.D.2 mm8 mm6.5 mm3 mmReference: Competence portal-C312/1 VOSP - the Service Scheduling application andprocess-- Uptime promise and connectivity vehiclesSme:RajathR2T33QUESTIONModel/Variant: 8-891634Customer wants to install his own Fleet Management System/Telematics in the truck.Which is the most appropriate hardware & software package that can be offered to thecustomer to tap the vehicle data?A.B.C.D.Hardware kit: 21930659; Software kit: 85135865Hardware kit: 21027152 ; Software kit: 85130445Hardware kit: 21930659 ; Software kit: 85153286Hardware kit: 21027152 ; Software kit: 85111487Reference: Trucks Portal-Accessories, Volvo trucks Software FMS GatewaySme:RajathR2T34QUESTIONModel/Variant: GeneralWhich of these is not a benefit for the customer (if he has Gold Agreement for his vehicle)A.B.C.D.Complete preventive & runningrepairsRepair cost is known for the agreement periodLimited number of invoicesCost of repair due to poor driving practiceReference: -services/service-contracts.htmlSme: Abhishek Banerjee
R2T35QUESTIONModel/Variant: GeneralFor which of these agreements, monthly tax invoice (To Customer) cannot be raised inadvanceA.B.C.D.Blue AgreementGold AgreementParts AgreementSilver AgreementReference: -services/servicecontracts.htmlSme: Abhishek BanerjeeR2T36QUESTIONModel/Variant: GeneralWhich tools can be used when the CSR have the first contact with the customer?A. Tech ToolB. Driver InterviewC. VOSPD. ImpactReference: T4312E/1 (704310) EDRP - Electronic Diagnostic and Repair Process - Test- CDportalSme: Sumesh Krishnan
Handbook/ Volvo FMX/ Select Model, chassis No, E-mail and send/ PDF link will be sent to e-mail/ Open handbook / PG 102, 103, 104. Sme: Madhu Kiran R2T17 QUESTION Model/Variant: B9R Which among the below statement/s is /are correct with respect to sealing of joints A. Non-welded joints and gaps should be sealed B.
Chapter 1 Question 1-1: Question 1-2: Question 1-3: Question 1-4: Question 1-5: Question 1-6: Question 1-7: Question 1-8: Question 1-9: Question 1-10: . QDRO take them into account? . 33 How may the participant’s retirement benefit be div
GCSE (91) edia Studies C 2019 Contents Introduction 3 Question 1 4 Question 2 6 Question 3 9 Question 4 13 Question 5 14 Question 6 16 Question 7 17 Question 8 18 Question 9 20 Would you prefer a Word version? Did you know that you can save this pdf as a Word file using Acrobat Pr
Question 6 : Ethyl Pentanoate is an ester. Esters are used for flavouring. Question 7 : Question 8 : H sub 2 /sub SO sub 4 /sub math pH - \log_{10} \left ( 2 \times 0.1 \right ) 0.69897 /math Question 9 : Question 1 0 : Question 1 1 : AAS is used to detect concentrations of ''metal'' ions. Questio n 1 2 : Question 1 3 : Question 1 4 :
Graduate Aptitude Test in Engineering Notations : Question Paper Name: CH: CHEMICAL ENGINEERING 31st Jan Shift1 Number of Questions: 65 Total Marks: 100.0 Number of Questions: 10 Section Marks: 15.0 Question Number : 1 Question Type : MCQ Options : Question Number : 2 Question Type : MCQ Options : Question Number : 3 Question Type : MCQ
Mar 10, 2021 · 3 Question No. 1-10 and Question No. 18 – 27 (including two Case Based Questions) are 1 mark questions and are to be answered in one word/sentence. 4 Case Based Questions (CBQ’s) are Question No. 7-10 and Question No. 25-27. 5 Question No. 11-12 and Question No. 28 – 29 are 3 mark
Solution to 79 Question 80 Solution to 80 Question 81 Solution to 81 Question 82 Solution to 82 Question 83 Solution to 83 Question 85 Solution to 85 Question 86 Solution to 86 Chapter 7: Cables Question 88 Solution to 88
QUESTION 3: 40 marks; 30 minutes Topic of the question: This question integrates: Statement of Financial Position and notes to the Financial Statements Financial accounting Statement of financial position Note to the financial statement Ratio and analysis QUESTION 4: 22 marks; 20 minutes Topic of the question: This question integrates:
vation in automotive retail is the imperative – and the time to get started is now. Against this backdrop and based on our extensive research and analyses (Textbox 2), we will provide a comprehensive perspective on three key questions that are currently a top priority for automotive OEMs and dealers: 1. Why exactly is the traditional automotive retail model so severely under pressure at .
