with Metallic Center SectionE23: EXP VIEW2: INSTAL & OP1: PUMP SPECSE2 Metallic Pumps Aluminum4: WARRANTYService & Operating ManualOriginal InstructionsVersa-Matic2" Elima-Matic Bolted Aluminum – ATEXVERSA-MATIC Warren Rupp, Inc. A Unit of IDEX Corporation800 North Main Street, Mansfield, OH 44902 USA Phone: (419) 526-7296 www.versamatic.com Copyright 2014 Warren Rupp, Inc. All rights reserved
Safety InformationIMPORTANTWARNINGWhen used for toxic or aggressive fluids, the pump shouldalways be flushed clean prior to disassembly.Read the safety warnings and instructions in this manualbefore pump installation and start-up. Failure to comply withthe recommendations stated in this manual could damage thepump and void factory warranty.Before maintenance or repair, shut off the compressed air line,bleed the pressure, and disconnect the air line from the pump.Be certain that approved eye protection and protective clothingare worn at all times. Failure to follow these recommendationsmay result in serious injury or death.When the pump is used for materials that tend to settle outor solidify, the pump should be flushed after each use toprevent damage. In freezing temperatures the pump should becompletely drained between uses.Airborne particles and loud noise hazards. Wear eye and earprotection.CAUTIONIn the event of diaphragm rupture, pumped material may enterthe air end of the pump, and be discharged into the atmosphere.If pumping a product that is hazardous or toxic, the air exhaustmust be piped to an appropriate area for safe containment.Before pump operation, inspect all fasteners for looseningcaused by gasket creep. Retighten loose fasteners to preventleakage. Follow recommended torques stated in this manual.Take action to prevent static sparking. Fire or explosion canresult, especially when handling flammable liquids. The pump,piping, valves, containers and other miscellaneous equipmentmust be properly grounded.Nonmetallic pumps and plastic components are not UVstabilized. Ultraviolet radiation can damage these parts andnegatively affect material properties. Do not expose to UV lightfor extended periods of time.This pump is pressurized internally with air pressure duringoperation. Make certain that all fasteners are in good conditionand are reinstalled properly during reassembly.WARNINGPump not designed, tested or certified to be powered bycompressed natural gas. Powering the pump with naturalgas will void the warranty.Use safe practices when liftingkgGrounding the PumpTo be fully groundable, the pumps must be ATEX Compliant. Refer to the nomenclature page for ordering information.Optional 8 foot long (244 centimeters) Ground Strap is available for easy ground connection.To reduce the risk of static electrical sparking, this pump must be grounded. Check the localelectrical code for detailed grounding instruction and the type of equipment required.Refer to nomenclature page for ordering information.WARNINGTake action to prevent static sparking.Fire or explosion can result, especiallywhen handling flammable liquids. Thepump, piping, valves, containers orother miscellaneous equipment mustbe grounded.www . versamatic . come2mdlCsmATEXAB-rev0514
Table of ContentsSECTION 1: PUMP SPECIFICATIONS.1 Nomenclature Performance Materials Dimensional DrawingsSECTION 2: INSTALLATION & OPERATION.6 Principle of Pump Operation Typical Installation Guide TroubleshootingSECTION 3: EXPLODED VIEW.9 Composite Drawings Parts List Materials CodeSECTION 4: WARRANTY & CERTIFICATES.13 Warranty CE Declaration of Conformity - Machinery ATEX Declaration of Conformity
Performance80Flow RateAdjustable to . . . . . . . . 0-163 gpm (617 lpm)Port SizeSuction . . . . . . . . . . . . . . . . . . . . . . . 2" NPTDischarge . . . . . . . . . . . . . . . . . . . . . 2" NPTAir Inlet . . . . . . . . . . . . . . . . . . . . . 1/2" NPTAir Exhaust . . . . . . . . . . . . . . . . . . . 1" NPTSuction LiftDry . . . . . . . . . . . . . . . . . . . . . . . . 18' (5.5 m)Wet . . . . . . . . . . . . . . . . . . . . . . . 32' (9.8 m)Max Solid Size (Diameter). . . . . . . . . . . . . . . . . . . . . . 7/16" (11.1 mm)Max Noise Level . . . . . . . . . . . . 92 dB(A)Shipping WeightsAluminum . . . . . . . . . . . . . . 81 lbs (36.7 kg)703 Model E2 Aluminum Bolted72006160520100Meters120804010 204012085030AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI6080100432SCFM 020100Feet BAR0020406080100120Capacity in U.S. Gallons Per Minute080160240320400480Capacity in Liters Per Minute140160640560NOTE: Performance based on the following: elastomeric fitted pump, flooded suction,water at ambient conditions. The use of other materials and varying hydraulic conditionsmay result in deviations in excess of 10 20AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI401208200Capacity Per Stroke, 0.53 Gal. (2.00 L)1406080100Discharge Head in PSI320Flow RateAdjustable to . . . . . . . . 0-154 gpm (583 lpm)Port SizeSuction . . . . . . . . . . . . . . . . . . . . . . 2" NPTFDischarge . . . . . . . . . . . . . . . . . . . . 2" NPTFAir Inlet . . . . . . . . . . . . . . . . . . . . . 1/2" NPTAir Exhaust . . . . . . . . . . . . . . . . . . . 1" NPTSuction LiftDry . . . . . . . . . . . . . . . . . . . . . . . . 17' (5.2 m)Wet . . . . . . . . . . . . . . . . . . . . . . . 30' (9.1 m)Max Solid Size (Diameter). . . . . . . . . . . . . . . . . . . . . . 7/16" (11.1 mm)Max Noise Level . . . . . . . . . . . . 92 dB(A)Shipping WeightsAluminum . . . . . . . . . . . . . . 81 lbs (36.7 kg)Flow RateAdjustable to . . . . . . . . 0-143 gpm (541 lpm)Port SizeSuction . . . . . . . . . . . . . . . . . . . . . . 2" NPTFDischarge . . . . . . . . . . . . . . . . . . . . 2" NPTFAir Inlet . . . . . . . . . . . . . . . . . . . . . 1/2" NPTAir Exhaust . . . . . . . . . . . . . . . . . . . 1" NPTSuction LiftDry . . . . . . . . . . . . . . . . . . . . . . . . . . 11' (3 m)Wet . . . . . . . . . . . . . . . . . . . . . . . 29' (9.1 m)Max Solid Size (Diameter). . . . . . . . . . . . . . . . . . . . . . 7/16" (11.1 mm)Max Noise Level . . . . . . . . . . . 102 dB(A)Shipping WeightsAluminum . . . . . . . . . . . . . . 81 lbs (36.7 kg)240Displacement Per Stroke, 0.60 Gal. (2.27 L)14096040E2 - 2” Bolted Aluminum Pump – Metallic CenterELASTOMERIC AND TPE FITTED - DOMEDE2 - 2” Bolted Aluminum Pump – Metallic CenterPTFE FITTED28010Discharge Head in PSI32090432SCFM 0201000Feet BAR020408001606080100120Capacity in U.S. Gallons Per Minute240320400480Capacity in Liters Per Minute140160640560NOTE: Performance based on the following: elastomeric fitted pump, flooded suction,water at ambient conditions. The use of other materials and varying hydraulic conditionsmay result in deviations in excess of 1208040432100Feet BARCapacity Per Stroke, 0.35 Gal. (1.32 L)14010 20 40120AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI60 80100100Discharge Head in PSI1: PUMP SPECSE2 - 2” Bolted Aluminum Pump – Metallic CenterELASTOMERIC AND TPE FITTED - RUGGED1208060SCFM 401606080100120Capacity in U.S. Gallons Per Minute240320400480Capacity in Liters Per Minute140560160640NOTE: Performance based on the following: PTFE fitted pump, flooded suction, waterat ambient conditions. The use of other materials and varying hydraulic conditions mayresult in deviations in excess of 5%.www . versamatic . come2mdlCsmATEXAB-rev0514
7DimensionalDrawings56E2 Aluminum Bolted43 452 3Dimensionally Interchangeable with Versa-Matic Clamped PumpsDimensions in inches (mm dimensions in brackets)The dimensions on this drawing are for reference only. A certified drawing can be requested if physical dimensions are needed.13.13333.5017.72450.092" NPT/BSP TAPEREDDISCHARGE PORT2" NPTR INLET13.1333.52.5063.502" NPT/BSP TAPEREDDISCHARGE PORT2.5063.501/2" NPTAIR INLET25.05636.2725.05636.2719.72500.991" NPTEXHAUST PORT1: PUMP SPECS17.72450.0926.66677.1219.72500.991" NPTEXHAUST 5063.502" NPT/BSP TAPEREDSUCTION 28.603.3785.5113.82350.94BOTTOM VIEW9.00228.603.3785.5113.82350.94BOTTOM VIEWMADE FROMPART E2AAxxxx9CTOLERANCMATERIALMATERIALN/AEFERENCEONLY. A CERTIFIEDe2mdlCsmATEXAB-rev0514ENSIONS ARE NEEDED.AN/A.XX.XXXANGULARModel E2 Aluminum Bolted 4www . versamatic . comVOLUME:INITIAL RELEASEAJLL1/8/13INITIAL RELEASE3inPUMP REFERENCEJLL1/8/13EST WT:lbsPROJECTSURFACE FINSVOLUME:PUMP REFERENDO NOT SCALE D
Dimensional DrawingsE27 Aluminum Bolted54Dimensionally Interchangeable with 6Wilden Clamped PumpsDimensions in inches (mm dimensions in brackets)613.13333.50T PORT022The dimensions on this drawing are for reference only. A certified drawing can be requested if physical dimensions are needed.17.72450.091: PUMP SPECS94352" NPT/BSP TAPEREDDISCHARGE PORT2" NPT/BSP TAPEREDDISCHARGE PORT2.5063.50261/2" NPTAIR 9749.9119.72500.9926.66677.121" NPTEXHAUST PORT.5012.71.5012.712" NPT/BSP TAPEREDSUCTION PORT2" NPT/BSP TAPEREDSUCTION .94PART NUMBER5 Model E2 Aluminum BoltedRTIFIEDRAWING ARE FOR REFERENCE ONLY. A CERTIFIEDE2AAxxxx9C-DWMATERIALwww . versamatic. comN/AMADE FROMN/Ae2mdlCsmATEXAB-rev0514UNLESS OTHESPECIFIETOLERANC.XX.XXXANGULAR
Principle of Pump OperationAir-Operated Double Diaphragm (AODD) pumps are poweredby compressed air or nitrogen.The main directional (air) control valve ① distributescompressed air to an air chamber, exerting uniform pressureover the inner surface of the diaphragm ②. At the same time,the exhausting air ③ from behind the opposite diaphragmis directed through the air valve assembly(s) to an exhaustport ④.DischargedFluidThe pump primes as a result of the suction stroke. Thesuction stroke lowers the chamber pressure (P3) increasingthe chamber volume. This results in a pressure differentialnecessary for atmospheric pressure (P4) to push the fluidthrough the suction piping and across the suction side checkvalve and into the outer fluid chamber ⑦.PUMP INSTALLATION AREADischargeStrokeSAFE AIRSuction (side) stroking also initiates the reciprocating(shifting, stroking or cycling) action of the pump.EXHAUSTThe suctionDISPOSALdiaphragm’s movement is mechanically pulled throughAREA itsstroke. The diaphragm’s inner plate makes contact with an1" DIAMETER AIRactuator plunger aligned to shift the pilot signaling valve.EXHAUST PIPINGOnce actuated, the pilot valve sends a pressureMUFFLERsignal to theopposite end of the main directional air valve, redirecting thecompressed air to the opposite inner chamber.SuctionStrokePrimedFluidSUBMERGED ILLUSTRATIONMUFFLERLIQUIDLEVEL1" DIAMETER AIREXHAUST PIPINGSUCTIONLINEPump can be submerged if the pump materials of constructionare compatible with the liquid being pumped. The air exhaustmust be piped above the liquid level. When the pumped productMUFFLERsource is at a higher level than the pump (flooded suctioncondition), pipe the exhaust higher than the product source toprevent siphoning spills.LIQUIDLEVEL1" DIAMETER AIREXHAUST PIPINGSUCTIONLINEe2mdlCsmATEXAB-rev0514www . versamatic . comModel E2 Aluminum Bolted 62: INSTAL & OPAs inner chamber pressure (P1) exceeds liquid chamberpressure (P2), the rod ⑤ connected diaphragms shifttogether creating discharge on one side and suction on theopposite side. The discharged and primed liquid’s directionsare controlled by the check valves (ball or flap)⑥ orientation.Air Line
Recommended Installation GuideAvailable Accessories:1. Surge Suppressor2. Filter/Regulator3. Air DryerUnregulated AirSupply to SurgeSuppressor1Surge SuppressorPressure GaugeShut-Off ValveNote: Surge Suppressor andPiping must be supported afterthe flexible connection.Pipe Connection(Style Optional)Flexible ConnectorDischarge2: INSTAL & OPCheckValveMuffler(Optional Piped Exhaust)Shut-OffValveDrain Port2Flexible ConnectorVacuumGaugeAir Inlet3Filter RegulatorP/N: 020.V107.000Air DryerSuctionCAUTIONShut-Off ValveThe air exhaust shouldbe p iped to an areafor safe d ispositionof the product b eingpumped, in the event ofa diaphragm failure.Drain PortInstallation And Start-UpLocate the pump as close to the product being pumped as possible. Keep the suction line length and number of fittings to a minimum. Do not reduce the suction linediameter.Air SupplyConnect the pump air inlet to an air supply with sufficient capacity and pressure to achieve desired performance. A pressure regulating valve should be installed toinsure air supply pressure does not exceed recommended limits.Air Valve LubricationThe air distribution system is designed to operate WITHOUT lubrication. This is the standard mode of operation. If lubrication is desired, install an air line lubricatorset to deliver one drop of SAE 10 non-detergent oil for every 20 SCFM (9.4 liters/sec.) of air the pump consumes. Consult the Performance Curve to determine airconsumption.Air Line MoistureWater in the compressed air supply may cause icing or freezing of the exhaust air, causing the pump to cycle erratically or stop operating. Water in the air supply canbe reduced by using a point-of-use air dryer.Air Inlet And PrimingTo start the pump, slightly open the air shut-off valve. After the pump primes, the air valve can be opened to increase air flow as desired. If opening the valveincreases cycling rate, but does not increase the rate of flow, cavitation has occurred. The valve should be closed slightly to obtain the most efficient air flow to pumpflow ratio.7 Model E2 Aluminum Boltedwww . versamatic . come2mdlCsmATEXAB-rev0514
Troubleshooting GuidePump Cycles OncePump Will Not Operate/ CyclePump Cycles and WillNot Prime or No FlowPotential Cause(s):Deadhead (system pressure meets or exceeds airsupply pressure).Air valve or intermediate gaskets installed incorrectly.Bent or missing actuator plunger.Pump is over lubricated.Lack of air (line size, PSI, CFM).Check air distribution system.Discharge line is blocked or clogged manifolds.Deadhead (system pressure meets or exceeds airsupply pressure).Blocked air exhaust muffler.Pumped fluid in air exhaust muffler.Pump chamber is blocked.Cavitation on suction side.Check valve obstructed. Valve ball(s) not seatingproperly or sticking.Product LeakingThrough ExhaustValve ball(s) missing (pushed into chamber ormanifold).Valve ball(s)/seat(s) damaged or attacked by product.Check valve and/or seat is worn or needs adjusting.Suction line is blocked.Excessive suction lift.Suction side air leakage or air in product.Pumped fluid in air exhaust muffler.Over lubrication.Icing.Clogged manifolds.Deadhead (system pressure meets or exceeds airsupply pressure).Cavitation on suction side.Lack of air (line size, PSI, CFM).Excessive suction lift.Air supply pressure or volume exceeds system hd.Undersized suction line.Restrictive or undersized air line.Suction side air leakage or air in product.Suction line is blocked.Pumped fluid in air exhaust muffler.Check valve obstructed.Check valve and/or seat is worn or needs adjusting.Entrained air or vapor lock in chamber(s).Diaphragm failure, or diaphragm plates loose.Diaphragm stretched around center hole or bolt holes.Premature DiaphragmFailureCavitation.Excessive flooded suction pressure.Pump Cycles RunningSluggish/Stalling,Flow UnsatisfactoryMisapplication (chemical/physical incompatibility).Unbalanced CyclingIncorrect diaphragm plates or plates on backwards,installed incorrectly or worn.Excessive suction lift.Undersized suction line.Pumped fluid in air exhaust muffler.Suction side air leakage or air in product.Check valve obstructed.Check valve and/or seat is worn or needs adjusting.Entrained air or vapor lock in chamber(s).Recommendation(s):Increase the inlet air pressure to the pump. Pump is designed for 1:1 pressure ratio at zero flow.(Does not apply to high pressure 2:1 units).Install gaskets with holes properly aligned.Remove pilot valve and inspect actuator plungers.Set lubricator on lowest possible setting or remove. Units are designed for lube free operation.Check the air line size and length, compressor capacity (HP vs. cfm required).Disassemble and inspect main air distribution valve, pilot valve and pilot valve actuators.Check for inadvertently closed discharge line valves. Clean discharge manifolds/piping.Increase the inlet air pressure to the pump. Pump is designed for 1:1 pressure ratio at zero flow.(Does not apply to high pressure 2:1 units).Remove muffler screen, clean or de-ice, and re-install.Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly.Disassemble and inspect wetted chambers. Remove or flush any obstructions.Check suction condition (move pump closer to product).Disassemble the wet end of the pump and manually dislodge obstruction in the check valve pocket.Clean out around valve ball cage and valve seat area. Replace valve ball or valve seat if damaged.Use heavier valve ball material.Worn valve ball or valve seat. Worn fingers in valve ball cage (replace part). Check ChemicalResistance Guide for compatibility.Check Chemical Resistance Guide for compatibility.Inspect check valves and seats for wear and proper setting. Replace if necessary.Remove or flush obstruction. Check and clear all suction screens or strainers.For lifts exceeding 20’ of liquid, filling the chambers with liquid will prime the pump in most cases.Visually inspect all suction-side gaskets and pipe connections.Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly.Set lubricator on lowest possible setting or remove. Units are designed for lube free operation.Remove muffler screen, de-ice, and re-install. Install a point of use air drier.Clean manifolds to allow proper air flowIncrease the inlet air pressure to the pump. Pump is designed for 1:1 pressure ratio at zero flow.(Does not apply to high pressure 2:1 units).Check suction (move pump closer to product).Check the air line size, length, compressor capacity.For lifts exceeding 20’ of liquid, filling the chambers with liquid will prime the pump in most cases.Decrease inlet air (press. and vol.) to the pump. Pump is cavitating the fluid by fast cycling.Meet or exceed pump connections.Install a larger air line and connection.Visually inspect all suction-side gaskets and pipe connections.Remove or flush obstruction. Check and clear all suction screens or strainers.Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly.Disassemble the wet end of the pump and manually dislodge obstruction in the check valve pocket.Inspect check valves and seats for wear and proper setting. Replace if necessary.Purge chambers through tapped chamber vent plugs. Purging the chambers of air can be dangerous.Replace diaphragms, check for damage and ensure diaphragm plates are tight.Check for excessive inlet pressure or air pressure. Consult Chemical Resistance Chart for compatibilitywith products, cleaners, temperature limitations and lubrication.Enlarge pipe diameter on suction side of pump.Move pump closer to product. Raise pump/place pump on top of tank to reduce inlet pressure.Install Back pressure device (Tech bulletin 41r). Add accumulation tank or pulsation dampener.Consult Chemical Resistance Chart for compatibility with products, cleaners, temperature limitationsand lubrication.Check Operating Manual to check for correct part and installation. Ensure outer plates have not beenworn to a sharp edge.For lifts exceeding 20’ of liquid, filling the chambers with liquid will prime the pump in most cases.Meet or exceed pump connections.Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly.Visually inspect all suction-side gaskets and pipe connections.Disassemble the wet end of the pump and manually dislodge obstruction in the check valve pocket.Inspect check valves and seats for wear and proper setting. Replace if necessary.Purge chambers through tapped chamber vent plugs.For additional troubleshooting tips contact After Sales Support at service.warrenrupp@idexcorp.com or 419-524-8388e2mdlCsmATEXAB-rev0514www . versamatic . comModel E2 Aluminum Bolted 82: INSTAL & OPSymptom:
Composite Repair Parts Drawing - Elastomeric and TPE 3030313131313030303032METAL SEAT NSIDE)SIDE)3228DOME DIAPHRAGM HRAGMASSEMBLYASSEMBLY3939393931313131METAL SEAT DISCHARGESIDE)SIDE)1111111188 88373737373522 22303133 3335353535Torque Setting:60 in-lbs.(6.78 N-m)39301131METAL SEAT ASSEMBLY(SUCTION SIDE)IAPHRAGM ASSEMBLY363636362525252530303030DROP IN 22393939392938 2638383818203434343424For XL Material ONLY9 Model E2 Aluminum Bolted23723232323373710 3737 11383838383917393939171717Torque MaterialONLYONLY21Torque Setting:480 in-lbs.(54.2 N-m)600 in-lbs (67.8 N-m)39161616164613Torque bs(67.8 N-m)600in-lbs(67.8N-m)600in-lbsONLY(67.8 N-m)ForXL Material14383833121212121818181828282828323: EXP 929292929368232323232351515151537METAL SEAT ASSEMBLY(DISCHARGE SIDE)1739Torque Setting:275 in-lbs.(31.1 N-m)3634www . versamatic . come2mdlCsmATEXAB-rev051436363636
Composite Repair Parts List - Elastomeric and TPE FittedQty.111161612213DescriptionValve Body Assembly (includes items 2-11)Valve BodyValve Body GasketValve SleeveO-ringValve Spool Assembly (Includes items 7)Glyde Ring AssemblyAir Valve ScreenEnd Cap GasketEnd CapMounting Screws (8 included on item 1)Item #121314151617181920212223Qty.122228161181Item #Qty.Description242526272829303132122222444Main ShaftDiaphragm (See Below Material Chart)O-ringInner Diaphragm PlateBumper WasherOuter Diaphragm PlateValve Seat (See Below Material Chart)Valve Seat O-Ring (See Below Material Chart)Valve Ball (See Below Material Chart)Item #3334Qty.216351361373839122828Air Valve AssemblyCenter Section AssemblyDescriptionCenter Block Assembly (Includes item 13 & 14)Bearing sleeveMain Shaft O-RingAir ChamberAir Chamber GasketBoltPilot Sleeve Assembly (include item 19)O-ringRetaining RingPilot Spool Assembly (Includes item 22)O-ringMufflerDiaphragm Assembly / 21BVB221Part 0S1001Part NumberP24-400DC 530.033.000Part NumberP24-103P24-501V240xx(See Note 2)V241xxVersa-DomeV225xxN/AV226BVB226Wet End AssemblyDescriptionPart NumberWater ChamberV235FBWater Chamber Bolt170.020.330Discharge ManifoldV236FBDischarge Manifold (BSP Option)V236FBBSPDischarge Drop in Manifold518.V006.156Discharge Drop in Manifold (BSP)518.V006.156 EWD Discharge Drop in Manifold518.V006.156 WWD Discharge Drop in Manifold (BSP)518.V006.156 WESuction ManifoldV237FBSuction Manifold (BSP Option)V237FBBSPSuction Drop in Manifold518.V007.156Suction Drop in Manifold (BSP)518.V007.156 EManifold BoltV251DNutV354CWasherV302GAElastomer Material SpecificationsVersa-DomeVersa-Rugged Diaphragm P/N"Ball P/N"Seat P/NDiaphragm 40GV240AN/AN/AN/A(See Note 1 Below)3: EXP VIEWItem #1234567891011Seat O-RingN/AN/AN/AN/AV240TN/AN/AN/AN/ANotes:1.) The metallic seat material is to match the water chamber material. In addition to this seat, (4) o-rings are needed. (Ref Note 2)2.) These (4) o-rings are only used with metallic fitted seats.e2mdlCsmATEXAB-rev0514www . versamatic . comModel E2 Aluminum Bolted 10
Composite Repair Parts Drawing - PTFE Fitted38 383824 242438 38383232 323232 323030 303131 .78(6.78N-m)N-m)36 363639 393911 111129 29291 1130 30308 8835 IDE)SIDE)SIDE)323224METAL SEAT ASSEMBLY(DISCHARGE SIDE)3026 262622 2222METAL SEAT ASSEMBLY27 2727 SIDE) 21 21(SUCTION2125 25259 99 1115 151530 3030392329 2929303928Torque Setting:480 in-lbs.(54.2 N-m)3: EXP VIEW39 3939303234 32 3230 303014273922182039 39392335392117352314173934342936Torque Setting:275 in-lbs.(31.1 N-m)39393234303639323011 Model E2 Aluminum Bolted101213392429113916Torque Setting:275 in-lbs.28(31.1N-m)391091520 1.1(31.1N-m)N-m)242536 36369318263284121319Torque Setting:480 in-lbs.(54.2 N-m)34 343421Torque60 in-lbs(6.78 N-11235 353523 232317 1717277539 39391622254DROP IN MANIFOLDS19325614 141428 28282611 1111835METAL SEAT ASSEMBLY(DISCHARGE SIDE)24 2424Torque Setting:60 in-lbs.(6.78 N-m)39 393936DROP IN MANIFOLDS19 1919118 181820 20201539 39393516 1616FUSION DIAPHRAGM n-lbs.(54.2(54.2N-m)N-m)10 101012 121213 1313303138363932132 32327 77383 33METAL SEAT ASSEMBLY(SUCTION SIDE)294 446 663230FUSION DIAPHRAGM ASSEMBLY2 2230242938DROPDROPDROPIN ININMANIFOLDSMANIFOLDSMANIFOLDS31265 5538www . versamatic . come2mdlCsmATEXAB-rev0514
Composite Repair Parts List - PTFE FittedQty.111161612213DescriptionValve Body (includes items 2-11)Valve BodyValve Body GasketValve SleeveO-ringValve Spool Assembly (Includes items 7)Glyde Ring AssemblyAir Valve ScreenEnd Cap GasketEnd CapMounting Screws (8 included on item 1)Item #121314151617181920212223Qty.122228161181Item #Qty.Description242526272829303132331222222444Main ShaftShaft StudDiaphragmBack Up DiaphragmInner Diaphragm PlateBumper WasherOuter Diaphragm PlateValve Seat (See Material Chart Below)Valve Seat O-RingValve BallItem #3435Qty.216361371383940122828DescriptionWater ChamberWater Chamber BoltDischarge ManifoldDischarge Manifold (BSP Option)Discharge Drop in ManifoldDischarge Drop in Manifold (BSP)WD Discharge Drop in ManifoldWD Discharge Drop in Manifold (BSP)Suction ManifoldSuction Manifold (BSP Option)Suction Drop in ManifoldSuction Drop in Manifold (BSP)Manifold BoltNutWasherAir Valve AssemblyCenter Section AssemblyDescriptionCenter Block Assembly (Includes item 13 & 14)Bearing SleeveMain Shaft O-RingAir ChamberAir Chamber GasketBoltPilot Sleeve Assembly (include item 19)O-ringRetaining RingPilot Spool Assembly (Includes item 22)O-ringMufflerDiaphragm Assembly / ElastomersMaterialAluminumStainless SteelPTFE Two PieceP24-102V221FV224TF-FBV224TFBV221TIV221TOWet End AssemblyMaterial SpecificationsPart 0S1001Part NumberP24-400DC 3.358530.033.000Part NumberP24-501V240xxV240T (See Note 1)V241TFFusionP24-103FN/AV224FN/AN/AN/APart 518.V006.156 E518.V006.156 W518.V006.156 EV237FBV237FBBSP518.V007.156518.V007.156 EV251DV354CV302GA3: EXP VIEWItem #1234567891011Seat P/NV240A (See Note 2 Below)SV240 (See Note 2 Below)Notes:1.) These (4) o-rings are only used with metallic fitted seats.2.) This metallic seat requires (4) V240T O-Rings.e2mdlCsmATEXAB-rev0514www . versamatic . comModel E2 Aluminum Bolted 12
Written Warranty5 - YEAR Limited Product WarrantyQuality System ISO9001 Certified Environmental Management Systems ISO14001 CertifiedVersa-Matic warrants to the original end-use purchaser that no product sold byVersa-Matic that bears a Versa-Matic brand shall fail under normal use and service due to a defect in materialor workmanship within five years from the date of shipment from Versa-Matic’s factory. See complete warranty at anty.pdf DECLARATION OF CONFORMITYDECLARATION DE CONFORMITE DECLARACION DE CONFORMIDAD ERKLÄRUNG BEZÜGLICH EINHALTUNG DER VORSCHRIFTENDICHIARAZIONE DI CONFORMITÀ CONFORMITEITSVERKLARING DEKLARATION OM ÖVERENSSTÄMMELSEEF-OVERENSSTEMMELSESERKLÆRING VAATIMUSTENMUKAISUUSVAKUUTUS SAMSVARSERKLÄRINGDECLARAÇAO DE CONFORMIDADEMANUFACTURED BY:FABRIQUE PAR:FABRICADA POR:HERGESTELLT VON:FABBRICATO DA:VERVAARDIGD DOOR:TILLVERKAD -MATIC Warren Rupp, Inc.A Unit of IDEX Corporation800 North Main StreetP.O. Box 1568Mansfield, OH 44901-1568 USATel: 419-526-7296Fax: 419-526-7289PUMP MODEL SERIES: E SERIES, V SERIES, VT SERIES, VSMA3, SPA15,RE SERIES AND U2 SERIES2006/42/ECThis product complies with the following European Community Directives:Ce produit est conforme aux directives de la Communauté européenne suivantes:on Machinery,Este producto cumple con las siguientes Directrices de la Comunidad Europea:toDieses produkt erfüllt die folgenden Vorschriften der Europäischen Gemeinschaft:Questo prodotto è conforme alle seguenti direttive CEE:Dir produkt voldoet aan de volgende EG-ric
e2mdlCsmATEXAB-rev0514 1 Model E2 Aluminum Bolted WWW.VERSAMATIC.COM Explanation of Pump Nomenclature Model Pump Size Wetted Parts Non-Wetted Parts Diaphragm Material E Elima-Matic 6 1/4" A Aluminum A Aluminum 1 Neoprene U Ultra-Matic 8 3/8" C Cast Iron S Stainless Steel 2 Nitrile (Nitrile) V V-Series 5 1/2" S Stainless Steel P Polypropylene 3 FKM (Fluorocarbon)
e3mdlCsmATEXC-rev1015 1 Model E3 Metallic Clamped WWW.VERSAMATIC.COM Explanation of Pump Nomenclature Model Pump Size Wetted Parts Non-Wetted Parts Diaphragm Material E Elima-Matic 6 1/4" A Aluminum A Aluminum 1 Neoprene U Ultra-Matic 8 3/8" C Cast Iron S Stainless Steel 2 Nitrile (Nitrile) V V-Series 5 1/2" S Stainless Steel P Polypropylene 3 FKM (Fluorocarbon)
connections. An overview of the current methods used to analyze bolted joint connections is given. Several methods for the design and analysis of bolted joint connections are presented. Guidance is provided for general bolted joint design, computation of preload uncertainty and preload loss, and the calculation of the bolted joint factor of safety.
baseball itself, Strat-O-Matic Baseball is easy to learn, yet can pro-vide a lifetime of challenge. Since 1961, when Strat-O-Matic Base-ball made its debut, the game has been enjoyed by children and adults. Many have played Strat-O-Matic for more than 30 years! Strat-O-Matic baseball is
Aluminum Sheet Aluminum Plate Aluminum Round Bar Aluminum Square Bar Aluminum Flat Bar Aluminum Angle Aluminum Structural Channel Aluminum Safety Grip Channel . peeled or smooth turned. Available in a wide selection of lengths and grades. 316/316LAvailable in pump shaft quality. Size
Aluminum Association's Task Group on Visual Quality Attributes of Aluminum Sheet and Plate. ALUMINUM ASSOCIATION SHEET AND PLATE DIVISION COMPANIES Alcan Inc. Alcoa, Inc. ARCO Aluminum Inc. Coastal Aluminum Rolling Mills, Inc. Corus Aluminium Rolled Products Jupiter Aluminum Corporation Kaiser Aluminum & Chemical Corporation Spectrulite .
abrasion resistance and low friction surface. Generally inert, with good chemical resistance except for strong acids and oxidizing agents. 190 F 88 C-20 F-29 C EPDM: Shows very good water and chemical resistance. Has poor resistance to oils and solvents, b
Service & Operating Manual 1: PUMP SPECS 2: INSTAL & OP 3: EXP VIEW 4: WARRANTY Original Instructions. e1mdlCsmFP-rev11 WWW.VERSAMATIC.COM IMPORTANT Read the safety warnings and instructions in this manual before pump installation and start-up. Failure to comply with the recommendations stated in this manual could damage the . Wilden is a .
MySQL Quick Start Guide This guide will help you: Add a MySQL database to your account. Find your database. Add additional users. Use the MySQL command-line tools through ssh. Install phpMyAdmin. Connect to your database using PHP. You’ll also find links to further information that will help you make the most of your database. Customer Support MySQL Quick Start Guide Page 1 Contents .