NI Serial Legacy Hardware - National Instruments
SPECIFICATIONS AND FEATURES GUIDENI Serial Legacy HardwareThis document lists safety and compliance information for NI Serial legacy hardware, as well asphysical specifications, software features, and recommended operating conditions.ContentsNI Legacy Serial Interfaces . 2Serial Hardware Features. 5Connectors and Pinouts . 6DB-9 Male . 6DB-25 Male . 710-Position Modular Jack (10P10C) . 868-Pin Connector. 9100-Pin Connector. 11Cables and Accessories . 13RS-232, RS-422, and RS-485. 14RS-232, RS-422, and RS-485 Features . 14RS-232 Loopback . 14RS-232 Signals . 14RS-485/422 Loopback . 15RS-485/422 Signals . 15RS-485 Topologies . 15RS-485 Transceiver Control. 16UART Data Frame Example . 16Hardware Specifications. 17Legacy PCI Serial Hardware . 17Environmental Characteristics (for All PCI Interfaces) . 20Other Specifications . 21Safety . 21Legacy PXI Serial Hardware . 22Environmental Characteristics (for All Legacy PXI Interfaces) . 26Other Specifications . 26Safety . 27Where to Go for Support . 28
2 NI Legacy Serial Interfacesni.comThe PCI interfaces listed in Table 1 can only accept 5 volts. Table 1. PCI InterfacesNI Serial Legacy Hardware Specifications and Features GuidePCI InterfacesStandard# PortsIsolatedMax Baud (kbits/s)Connector Type*FIFO Size (Bytes)PCI-232/2RS-2322No115.2DB-9 328No115.268-pin SCSI64PCI-232/16RS-23216No115.2100-pin SCSI64PCI-485/2RS-485/RS-4222No460.8DB-9 5/8RS-485/RS-4228No460.868-pin SCSI64PCI-232i/2RS-2322Yes115.2DB-9 S-485/RS-4222Yes460.8DB-9 male64PCI-485i/4RS-485/RS-4224Yes460.810P10C64* Serialconnector cables end in DB-9 male serial connectors.
Table 2. PXI InterfacesNI Serial Legacy Hardware Specifications and Features Guide*PXI InterfacesStandard# PortsIsolatedMax Baud (kbits/s)Connector Type*FIFO Size (Bytes)PXI-8420/2RS-2322No115.2DB-9 -2328No115.268-pin SCSI64PXI-8420/16RS-23216No115.2100-pin SCSI64PXI-8421/2RS-485/RS-4222No460.8DB-9 421/8RS-485/RS-4228No460.868-pin SCSI64PXI-8422/2RS-2322Yes115.2DB-9 S-485/RS-4222Yes460.8DB-9 al connector cables end in DB-9 male serial connectors. National Instruments 3
National Instruments considers the following baud rates to be standard. NI serial hardwaresupports these rates up to the maximum rate 30400960046080014400To set the baud rate, set the VISA Baud attribute or use the Windows SetCommState functionand pass the actual value of the baud rate in the BaudRate field of the DCB structure.Refer to Hardware Specifications for supported baud rates on each board.4 ni.com NI Serial Legacy Hardware Specifications and Features Guide
Serial Hardware FeaturesTo determine which features your product supports, refer to the following table.NI Serial Legacy Hardware Specifications and Features GuideTable 3. Serial Hardware 232,PXI-8420,PXI-8422 PCI-485eight port,PXI-8421eight port All otherPCI-485,PXI-8421,and PXI-8423 Resistors National Instruments* Requires† NotNI-Serial 3.5 or higher, for both Windows or LabVIEW RT.supported in LabVIEW RT. RS-485ProgrammaticallyControlled ansceiverControlHardwareImplemented FlowControl*RTS/CTSDTR/DSRXon/Xoff † † † 5
Connectors and PinoutsDB-9 MaleFigure 1. DB-9 Connector Pin LocationsPin 1Pin 6Pin 5Pin 9Table 4. DB-9 Male Pin DescriptionsPin232 DTE232 DCE422/4851DCD*DCDGND2RXDTXDCTS (HSI )3TXDRXDRTS (HSO )4DTR*DSRRXD 5GNDGNDRXD-6DSR*DTRCTS- (HSI-)7RTSCTSRTS- (HSO-)8CTSRTSTXD 9RI*RITXD-*These signals are “No Connect” on the PCI-232I and PXI-8422 ports and ports 9 to 16 on legacy16-port boards.Note6 ni.com DCE mode supported on USB-232/2 and USB-232/4 only.NI Serial Legacy Hardware Specifications and Features Guide
DB-25 MaleFigure 2. DB-25 Connector Pin LocationsPin 13Pin 1Pin 14Pin 25Table 5. DB-25 Pin Descriptions* ThesePin232422/4852TXDRTS (HSO )3RXDCTS (HSI )4RTSRTS- (HSO-)5CTSTXD 6DSR*CTS- (HSI-)7GNDRXD-8DCD*GND20DTR*RXD 22RI*TXD-signals are “No Connect” on the PCI-232I and PXI-8422 ports.NotePins not listed in this table are “No Connect.”NI Serial Legacy Hardware Specifications and Features Guide National Instruments 7
10-Position Modular Jack (10P10C)Figure 3. 10-Position Modular Jack Pin LocationsPin 1Pin 10Table 6. 10-Position Modular Jack Pin Descriptions* These8 Pin232422/4851No ConnectNo Connect2RI*TXD-3CTSTXD 4RTSRTS- (HSO-)5DSR*CTS- (HSI-)6GNDRXD-7DTR*RXD 8TXDRTS (HSO )9RXDCTS (HSI )10DCD*GNDsignals are “No Connect” on the PCI-232I and PXI-8422 ports.ni.com NI Serial Legacy Hardware Specifications and Features Guide
68-Pin ConnectorThe following figure and table give the 68-pin connector pin locations and descriptions. TheSCSI 68-pin connector and VHDCI 68-pin connector have the same pinout.Figure 4. 68-Pin SCSI Connector Pin LocationsPIN 68PIN 34PIN 35PIN 1NI Serial Legacy Hardware Specifications and Features Guide National Instruments 9
10Table 7. 68-Pin Connector Pin Descriptions ni.com68-Pin Connector Port2345678485 Signal485 D-Sub 9Connector232 Signal232 D-Sub TS 2RXD2655648393122145RTS 3TXD3645547383021134RXD 6625345362819112RTS-7RTS7615244352718101TXD 8CTS8675850413324167TXD-9RI9 1NI Serial Legacy Hardware Specifications and Features Guide
100-Pin ConnectorThe following figure and table give the pin locations and descriptions of the 100-pin connector.Figure 5. 100-Pin Connector Pin LocationsPIN 100PIN 50PIN 51PIN 1NI Serial Legacy Hardware Specifications and Features Guide National Instruments 11
12Table 8. 100-Pin Connector Pin Descriptions ni.com100-Pin Connector Port2345678910111213141516232 Signal232 D-Sub 6 1NI Serial Legacy Hardware Specifications and Features ��———RI*9*These signals are not supported on ports 9 to 16 of the PCI-232/16 and PXI-8420/16 serial boards.
Cables and AccessoriesThe following serial cables and accessories are available from National Instruments. Refer toni.com for more information.Table 9. Serial Cables and AccessoriesPartNumberDescriptionAdapter Cables (DB-9 and DB-25 connectors have jacksockets unless otherwise specified.)182844-01DB-9 RS485 terminating pass-through connector 120 Ω182845-01Serial cable, 10P10C modular plug to DB-9 male, 1 m182845-02Serial cable, 10P10C modular plug to DB-9 male, 2 m182845-03Serial cable, 10P10C modular plug to DB-9 male, 3 m182846-01Serial cable, 10P10C modular plug to DB-25 male, 1 m184428-01Serial cable, 10P10C modular plug to DB-9 male, 1 m, isolated199022-02Serial cable, 10P10C to DB-9 male, jackscrews, 2 m197545-01Serial cable, 68-pin VHDCI to eight DB-9 male, RS-232, 1 m197546-01Serial cable, 68-pin VHDCI to eight DB-9 male, RS-485, 1 mExtension and Null-Modem Cables (All cables have jackscrews.)182238-01Serial cable, RS232 null modem, DB-9 female to DB-9 female, 1 m182238-02Serial cable, RS232 null modem, DB-9 female to DB-9 female, 2 m182238-04Serial cable, RS232 null modem, DB-9 female to DB-9 female, 4 m183045-01Serial cable, RS232 straight through, DB-9 female to DB-9 female, 1 m183045-02Serial cable, RS232 straight through, DB-9 female to DB-9 female, 2 m183045-04Serial cable, RS232 straight through, DB-9 female to DB-9 female, 4 m183283-01Serial cable, RS485/RS422 null modem, DB-9 female to DB-9 female, 1 m183283-02Serial cable, RS485/RS422 null modem, DB-9 female to DB-9 female, 2 m183283-04Serial cable, RS485/RS422 null modem, DB-9 female to DB-9 female, 4 mNI Serial Legacy Hardware Specifications and Features Guide National Instruments 13
RS-232, RS-422, and RS-485RS-232, RS-422, and RS-485 FeaturesTable 10. RS-232, RS-422, and RS-485 FeaturesFeatureRS-232RS-422RS-485Single endedDifferentialDifferentialMaximum number of drivers1132Maximum number of receivers1103250 ft4,000 ft4,000 ft 25 V 7 V 12 to -7 V5 to 25 V2 to 6 V1.5 to 6 V 3 kΩ100 Ω60 ΩType of transmission linesMaximum cable lengthMaximum CMVDriver output*Driver load*Actual driver output varies depending on cable length and load.RS-232 LoopbackFigure 6. RS-232 LoopbackPin 5Pin 9Pin 1Pin 6TX/RXPin 5Pin 9Pin 1Pin 6AllRS-232 SignalsFigure 7. RS-232 Signals25 VSPACE, '0'3VUNKNOWN–3 VMARK, '1'–25 V14 ni.com NI Serial Legacy Hardware Specifications and Features Guide
RS-485/422 LoopbackFigure 8. RS-485/422 LoopbackPin 1Pin 6Pin 5Pin 9TX/RXPin 5Pin 9Pin 1Pin 6AllRS-485/422 SignalsFigure 9. RS-485/422 SignalsIf '–' ' 'then MARK, '1'If '–' ' 'then SPACE, '0'RS-422 Voltage: 7 VRS-485 Voltage:–7 V to 12 VRS-485 TopologiesFigure 10. 2-Wire Multidrop Network Using Terminating ResistorsSlave 1TxSlave 2TxRxSlave nTxRxRxMASTERTx120 Ω120 ΩRxFigure 11. 4-Wire Full-Duplex Multidrop Network Using Terminating ResistorsSlave 1MASTERTxTxRxRxSlave 2TxSlave nTxRx120 Ω120 Ω120 Ω120 ΩRxThe driver directly supports 4-wire full-duplex operation on peer-to-peer RS-485 networks.Multidrop RS-485 networks require additional software development.RS-485 terminators are available at ni.com/serial.NI Serial Legacy Hardware Specifications and Features Guide National Instruments 15
RS-485 Transceiver Control2-WireEnable4-WireDTR/EchoDTR/No EchoAutoTXONDTRDTRTXRXONONDTRTXThe available modes might vary with the controller or interface used. For further informationrefer to ni.com/kb and search for KnowledgeBase 67KEP64G.UART Data Frame Example0xD9—8 Data Bits, Odd Parity, 1 Stop BitDataIdleS10011011001234567PSIdleRS-232 5 V–5 VRS-4855VTX 0V5VTX–0VVoltages are for illustration only. Actual voltage levels may vary.16 ni.com NI Serial Legacy Hardware Specifications and Features Guide
Hardware SpecificationsLegacy PCI Serial HardwareThis section describes the characteristics of the legacy PCI serial hardware and therecommended operating conditions.PCI-232/2 (RS-232) and PCI-485/2 (RS-485/422)Dimensions . 10.67 14.22 cm(4.2 5.6 in.)I/O connector . DB-9 male connectorPower requirement (from PCI channel)PCI-485/2 5 VDC. 350 mA typical750 mA maximumPCI-232/2 5 VDC. 50 mA typical100 mA maximum 12 VDC. 20 mA typical200 mA maximumMaximum baud ratePCI-232/2. 115.2 kbpsPCI-485/2. 430.8 kbpsBoards support standard baud rates below the maximum.PCI-232/4 (RS-232) and PCI-485/4 (RS-485/422)Dimensions . 10.67 14.22 cm(4.2 5.6 in.)I/O connector1 . 10-position modular jack (10P10C)Power requirement (from PCI channel)PCI-485/4 5 VDC. 700 mA typical1.3 A maximumPCI-232/4 5 VDC. 70 mA typical150 mA maximum 12 VDC. 40 mA typical400 mA maximum1The four-port legacy PCI serial boards require a cable to convert the 10-position modular jack (10P10C)to either DB-9 or DB-25 male connectors.NI Serial Legacy Hardware Specifications and Features Guide National Instruments 17
Maximum baud ratePCI-232/4.115.2 kbpsPCI-485/4.430.8 kbpsBoards support standard baud rates below the maximum.PCI-232/8 (RS-232) and PCI-485/8 (RS-485/422)Dimensions .10.67 14.48 cm(4.2 5.7 in.)I/O connector1 .68-pin, SCSI type connectorPower requirement (from PCI channel)PCI-485/8 5 VDC.1.1 A typical2.0 A maximumPCI-232/8 5 VDC.100 mA typical180 mA maximum 12 VDC.80 mA typical800 mA maximumMaximum baud ratePCI-232/8.115.2 kbpsPCI-485/8.430.8 kbpsBoards support standard baud rates below the maximum.PCI-232/16 (RS-232)Dimensions .10.67 17.52 cm(4.2 6.9 in.)I/O connector2 .100-pin, SCSI type connectorPower requirement (from PCI channel)PCI-232/16 5 VDC.250 mA typical500 mA maximumMaximum baud rate .115.2 kbpsBoard supports standard baud rates below the maximum.12The eight-port legacy PCI serial boards require a cable, included in your kit, to convert the 68-pinconnector to eight DB-9 male connectors.The 16-port legacy PCI serial boards require a breakout box, included in your kit, to separate the 100-pinSCSI connector to 16 DB-9 male connectors.18 ni.com NI Serial Legacy Hardware Specifications and Features Guide
PCI-232i/2 (RS-232) and PCI-485i/2 (RS-485/422)Dimensions . 10.67 17.52 cm(4.2 6.9 in.)I/O connector . DB-9 male connectorOperating rated voltage (continuous)RS-232 . -25 V to 25 VRS-485 . -7 V to 12 VIsolation voltagesPort-to-portContinuous. 60 VDC (CAT I)Withstand . 2000 Vrms, verified by a 5 s dielectricwithstand testPort-to-hostContinuous. 60 VDC (CAT I)Withstand . 2000 Vrms, verified by a 5 s dielectricwithstand testPower requirement (from PCI channel)PCI-485i/2 5 VDC. 800 mA typical1.3 A maximumPCI-232i/2 5 VDC. 400 mA typical650 mA maximumMaximum baud ratePCI-232i/2 . 115.2 kbpsPCI-485i/2 . 430.8 kbpsBoards support standard baud rates below the maximum.PCI-232i/4 (RS-232) and PCI-485i/4 (RS-485/422)Dimensions . 10.67 17.44 cm(4.2 6.9 in.)I/O connector1 . 10-position modular jack (10P10C)Operating rated voltage (continuous)RS-232 . -25 V to 25 VRS-485 . -7 V to 12 V1The four-port legacy PCI serial boards require a cable to convert the 10-position (10P10C) modular jackto either DB-9 or DB-25 male connectors.NI Serial Legacy Hardware Specifications and Features Guide National Instruments 19
Isolation voltagesPort-to-portContinuous .60 VDC (CAT I)Withstand .2000 Vrms, verified by a 5 s dielectricwithstand testPort-to-hostContinuous .60 VDC (CAT I)Withstand .2000 Vrms, verified by a 5 s dielectricwithstand testPower requirement (from PCI channel)PCI-485i/4 5 VDC.1.0 A typical1.5 A maximumPCI-232i/4 5 VDC.500 mA typical750 mA maximumMaximum baud ratePCI-232i/4.115.2 kbpsPCI-485i/4.430.8 kbpsBoards support standard baud rates below the maximum.Environmental Characteristics (for All PCI Interfaces)Operating EnvironmentAmbient temperature .0 to 55 C(Tested in accordance with IEC-60068-2-1 andIEC-60068-2-2.)Relative humidity.10 to 90%, noncondensing(Tested in accordance with IEC-60068-2-56.)Altitude (maximum) .2,000 mPollution Degree .2Indoor use only.Storage EnvironmentAmbient temperature .-20 to 70 C(Tested in accordance with IEC-60068-2-1 andIEC-60068-2-2.)Relative humidity.5 to 95%, noncondensing(Tested in accordance with IEC-60068-2-56.)20 ni.com NI Serial Legacy Hardware Specifications and Features Guide
Other SpecificationsMaximum cable lengthRS-4851. 30 m (limited by EMC/surge)RS-232 . 2,500 pF equivalent (TIA-EIA-232-F 2.1.4)Data line ESD protection (human body model)RS-485 . 15 kVRS-232 . 15 kVNoteThis equipment is intended for indoor use only.SafetyThis product meets the requirements of the following standards of safety for electrical equipmentfor measurement, control, and laboratory use: IEC 61010-1, EN 61010-1 UL 61010-1, CSA 61010-1Note For UL and other safety certifications, refer to the product label or the OnlineProduct Certification section.Electromagnetic CompatibilityThis product meets the requirements of the following EMC standards for electrical equipmentfor measurement, control, and laboratory use: EN 61326 (IEC 61326): Class A emissions; Basic immunity EN 55011 (CISPR 11): Group 1, Class A emissions AS/NZS CISPR 11: Group 1, Class A emissions FCC 47 CFR Part 15B: Class A emissions ICES-001: Class A emissionsNote For the standards applied to assess the EMC of this product, refer to theOnline Product Certification section.NoteFor EMC compliance, operate this device with shielded cabling.CE ComplianceThis product meets the essential requirements of applicable European Directives as follows: 2006/95/EC; Low-Voltage Directive (safety) 2004/108/EC; Electromagnetic Compatibility Directive (EMC)1RS-485 is capable of 1.2 km (4,000 ft) without surge limitation.NI Serial Legacy Hardware Specifications and Features Guide National Instruments 21
Online Product CertificationRefer to the product Declaration of Conformity (DoC) for additional regulatory complianceinformation. To obtain product certifications and the DoC for this product, visit ni.com/certification, search by model number or product line, and click the appropriate link in theCertification column.Environmental ManagementNI is committed to designing and manufacturing products in an environmentally responsiblemanner. NI recognizes that eliminating certain hazardous substances from our products isbeneficial to the environment and to NI customers.For additional environmental information, refer to the Minimize Our Environmental Impact webpage at ni.com/environment. This page contains the environmental regulations anddirectives with which NI complies, as well as other environmental information not included inthis document.Waste Electrical and Electronic Equipment (WEEE)At the end of the product life cycle, all products must be sent to aWEEE recycling center. For more information about WEEE recycling centers,National Instruments WEEE initiatives, and compliance with WEEE Directive2002/96/EC on Waste and Electronic Equipment, visit ni.com/environment/weee.EU Customers ᄤֵᙃѻક ᶧ ࠊㅵ⧚ Ё RoHS Ё ᅶ᠋ National Instruments ヺড়Ё ᄤֵᙃѻકЁ䰤ࠊՓ ᶤѯ᳝ᆇ 䋼ᣛҸ(RoHS)DŽ݇Ѣ National Instruments Ё RoHS ড়㾘ᗻֵᙃˈ䇋ⱏᔩ ni.com/environment/rohs chinaDŽ (For information about China RoHS compliance,go to ni.com/environment/rohs china.)Legacy PXI Serial HardwareThis section describes the characteristics of the legacy PXI serial hardware and therecommended operating conditions.PXI-8420/2 (RS-232) and PXI-8421/2 (RS-485/422)Dimensions .100 160 mm(3.94 6.37 in.)I/O connector .DB-9 male connectorPower requirement (from PXI channel)PXI-8420/2 5 VDC.100 mA typical150 mA maximum 12 VDC.20 mA typical200 mA maximum22 ni.com NI Serial Legacy Hardware Specifications and Features Guide
PXI-8421/2 5 VDC. 350 mA typical750 mA maximumMaximum baud ratePXI-8420/2 . 115.2 kbpsPXI-8421/2 . 430.8 kbpsBoards support standard baud rates below the maximum.PXI-8420/4 (RS-232) and PXI-8421/4 (RS-485/422)Dimensions . 100 160 mm(3.94 6.37 in.)I/O connector1 . 10-position modular jack (10P10C)Power requirement (from PXI channel)PXI-8420/4 5 VDC. 125 mA typical200 mA maximum 12 VDC. 40 mA typical400 mA maximumPXI-8421/4 5 VDC. 350 mA typical750 mA maximumMaximum baud ratePXI-8420/4 . 115.2 kbpsPXI-8421/4 . 430.8 kbpsBoards support standard baud rates below the maximum.PXI-8420/8 (RS-232) and PXI-8421/8 (RS-485/422)Dimensions . 100 160 mm(3.94 6.37 in.)I/O connector2 . 68-pin, SCSI type connectorPower requirement (from PXI channel)PXI-8420/8 5 VDC. 150 mA typical250 mA maximum 12 VDC. 80 mA typical800 mA maximum12The four-port legacy PXI serial boards require a cable to convert the 10-position modular jack (10P10C)to either DB-9 or DB-25 male connectors.The eight-port legacy PXI serial boards require a cable, included in your kit, to convert the 68-pinconnector to eight DB-9 male connectors.NI Serial Legacy Hardware Specifications and Features Guide National Instruments 23
PXI-8421/8 5 VDC.1.1 A typical2.0 A maximumMaximum baud ratePXI-8420/8.115.2 kbpsPXI-8421/8.430.8 kbpsBoards support standard baud rates below the maximum.PXI-8420/16 (RS-232)Dimensions .100 160 mm(3.94 6.37 in.)I/O connector1 .100-pin, SCSI type connectorPower requirement (from PXI channel)PXI-8420/16 5 VDC.500 mA typical750 mA maximumMaximum baud rate .115.2 kbpsBoard supports standard baud rates below the maximum.PXI-8422/2 (RS-232) and PXI-8423/2 (RS-485/422)Dimensions .100 160 mm(3.94 6.37 in.)I/O connector .DB-9 male connectorOperating rated voltage (continuous)RS-232 .-25 V to 25 VRS-485 .-7 V to 12 VIsolation voltagesPort-to-portContinuous .60 VDC (CAT I)Withstand .2000 Vrms, verified by a 5 s dielectric withstandtestPort-to-hostContinuous .60 VDC (CAT I)Withstand .2000 Vrms, verified by a 5 s dielectric withstandtest1The 16-port legacy PXI serial boards require a breakout box, included in your kit, to separate the 100-pinconnector to 16 DB-9 male connectors.24 ni.com NI Serial Legacy Hardware Specifications and Features Guide
Power requirement (from PXI channel)PXI-8422/2 5 VDC. 400 mA typical650 mA maximumPXI-8423/2 5 VDC. 800 mA typical, 1.3 A maximumMaximum baud ratePXI-8422/2 . 115.2 kbpsPXI-8423/2 . 430.8 kbpsBoards support standard baud rates below the maximum.PXI-8422/4 (RS-232) and PXI-8423/4 (RS-485/422)Dimensions . 100 160 mm(3.94 6.37 in.)I/O connector1 . 10-position modular jack (10P10C)Operating rated voltage (continuous)RS-232 . -25 V to 25 VRS-485 . -7 V to 12 VIsolation voltagesPort-to-portContinuous. 60 VDC (CAT I)Withstand . 2000 Vrms,verified by a 5 s dielectric withstand testPort-to-hostContinuous. 60 VDC (CAT I)Withstand . 2000 Vrms,verified by a 5 s dielectric withstand testPower requirement (from PXI channel)PXI-8422/4 5 VDC. 500 mA typical750 mA maximumPXI-8423/4 5 VDC. 1.0 A typical1.5 A maximum1The four-port legacy PXI serial boards require a cable to convert the 10-position modular jack (10P10C)to either DB-9 or DB-25 male connectors.NI Serial Legacy Hardware Specifications and Features Guide National Instruments 25
Maximum baud ratePXI-8422/4.115.2 kbpsPXI-8423/4.430.8 kbpsBoards support standard baud rates below the maximum.Environmental Characteristics (for All LegacyPXI Interfaces)Operating EnvironmentAmbient temperature .0 to 55 C(Tested in accordance with IEC-60068-2-1 andIEC-60068-2-2.)Relative humidity.10 to 90%, noncondensing(Tested in accordance with IEC-60068-2-56.)Altitude (maximum) .2,000 mPollution Degree .2Indoor use only.Storage EnvironmentAmbient temperature .-20 to 70 C(Tested in accordance with IEC-60068-2-1 andIEC-
182238-04 Serial cable, RS232 null modem, DB-9 female to DB-9 female, 4 m 183045-01 Serial cable, RS232 straight through, DB-9 female to DB-9 female, 1 m 183045-02 Serial cable, RS232 straight through, DB-9 female to DB-9 female, 2 m 183045-04 Serial cable, RS232 straight through, DB-9 female to DB-9 female, 4 m 183283-01 Serial cable, RS485 .
1 TXD O (1) Serial port (Transmitted Data) 2 DTR_N O (1) Serial port (Data Terminal Ready) 3 RTS_N O (1) Serial port (Request To Send) 4 VDD_325 P RS232 VDD. The power pins for the serial port signals. When the serial port is 3.3V, this should be 3.3V. When the serial port is 2.5V, this should be 2.5V. 5 RXD I (2) Serial port (Received Data)
3 RTS_N O (1) Serial port (Request To Send) 4 VDD_325 P RS232 VDD. The power pins for the serial port signals. When the serial port is 3.3V, this should be 3.3V. When the serial port is 2.5V, this should be 2.5V. 5 RXD I (2) Serial port (Received Data) 6 RI_N I/O (3) Serial port (Ring Indicator) 7 GND P Ground 8 NC No Connect
- HARDWARE USER MANUAL - MANUEL DE L'UTILISATEUR HARDWARE . - HARDWAREHANDLEIDING - MANUALE D'USO HARDWARE - MANUAL DEL USUARIO DEL HARDWARE - MANUAL DO UTILIZADOR DO HARDWARE . - 取扱説明書 - 硬件用户手册. 1/18 Compatible: PC Hardware User Manual . 2/18 U.S. Air Force A -10C attack aircraft HOTAS (**) (Hands On Throttle And .
2.16 Schematic of a legacy logo endorsement 2.17 Example of a legacy program logo endorsement 2.18 Example of a legacy agency logo endorsement 2.19 Legacy logo endorsement of a sub-program or initiative lock up 2.20 Schematic of a legacy logo endorsing a sub-program 2.21 Example of a legacy logo
network governance phases: legacy conceptualization, legacy planning and implementation, legacy transfer, and post-Games legacy governance, as well as a number of governance mechanisms (e.g., contracts, policies) that had an impact on the overall governance of the event's legacy. Finally, a critical analysis of the governance of
HP 500B MT - Serial number-MXL 1240IKS HP Z200 - Serial number-2UA1091G78 HP Prodesk 400G1 SFF - Serial number-MSL5131SMl Rio Magicard Pro - Serial number-61 F7849 HP Compaq DC5700 Microtower - Serial number-2UA7120SFR HP Workstation XW6200 - Serial number-2UA6020G4B REGULAR MEETING. April 5. 2021 Dated this 5th day of April, 2021 ATTEST:
ECHO: PB-770T (Serial. INTRODUCTION (Serial number : 11000001-11999999) (Serial number : 12000001-12999999) (Serial number : 13000001-13999999) number : 11000001-11999999) (Serial number : 12000001-12999999) (Serial number : 13000001-13999999) CONTENTS. We are constantly working on techni
criminal case process; the philosophies and alterna-tive methods of corrections; the nature and processes of treating the juvenile offender; the causes of crime; and the role of government and citizens in finding solutions to America’s crime problems. 2. Develop, state, and defend positions on key issues facing the criminal justice system, including the treatment of victims, police-community .
