SDS SNC 2000 DREW MARINE - Algoma MSDS Library
SNC 2000Drew MarineChemwatch: 24-0214Version No: 5.1.1.1Safety Data Sheet according to WHMIS 2015 requirementsIssue Date: 02/10/2017Print Date: 12/06/2018L.GHS.CAN.ENSECTION 1 IDENTIFICATIONProduct IdentifierProduct nameProper shipping nameOther means of identificationSNC 2000ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (contains dipentene and solvent naphtha petroleum, heavy aromatic)Not AvailableRecommended use of the chemical and restrictions on useRelevant identified usesUse according to manufacturer's directions.Engine Parts Cleaner for Vessels.Name, address, and telephone number of the chemical manufacturer, importer, or other responsible partyRegistered company nameAddressTelephoneFaxWebsiteEmailDrew Marine100 South Jefferson Road NJ 07981 United States973 526-5700Not ergency phone numberAssociation / OrganisationEmergency telephone numbersOther emergency telephonenumbersNot AvailableThe numbers below are for EMERGENCY USE ONLY. Use the corporate number above for all other calls.CHEMWATCH: From within the US and CANADA: 1 877-715-9305 OR call 613 9573 3112. From outside the US and Canada: 800 2436 2255 ( 800CHEMCALL) or 613 9573 3112CHEMWATCH EMERGENCY RESPONSEPrimary NumberAlternative Number 1Alternative Number 2(1) 877 715 9305(1) 877 715 9305 612 9186 1132Once connected and if the message is not in your prefered language then please dial 01Une fois connecté et si le message n'est pas dans votre langue préférée alors s'il vous plaît cadran 07SECTION 2 HAZARD(S) IDENTIFICATIONClassification of the substance or mixtureClassificationFlammable Liquid Category 4, Skin Corrosion/Irritation Category 2, Skin Sensitizer Category 1, Specific target organ toxicity - single exposure Category 3(narcotic effects), Aspiration Hazard Category 1, Acute Aquatic Hazard Category 2, Chronic Aquatic Hazard Category 2Label elementsHazard pictogram(s)SIGNAL WORDDANGERHazard statement(s)H227Combustible liquid.H315Causes skin irritation.H317May cause an allergic skin reaction.H336May cause drowsiness or dizziness.H304May be fatal if swallowed and enters airways.H411Toxic to aquatic life with long lasting effects.Continued.
Chemwatch: 24-0214Page 2 of 12Version No: 5.1.1.1SNC 2000Issue Date: 02/10/2017Print Date: 12/06/2018Hazard(s) not otherwise specifiedNot ApplicablePrecautionary statement(s) PreventionP210Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.P271Use only outdoors or in a well-ventilated area.P280Wear protective gloves/protective clothing/eye protection/face protection.P261Avoid breathing mist/vapours/spray.P273Avoid release to the environment.P272Contaminated work clothing should not be allowed out of the workplace.Precautionary statement(s) ResponseP301 P310P331IF SWALLOWED: Immediately call a POISON CENTER/doctor/physician/first aider.Do NOT induce vomiting.P370 P378In case of fire: Use alcohol resistant foam or normal protein foam to extinguish.P302 P352IF ON SKIN: Wash with plenty of water and soap.P312Call a POISON CENTER/doctor/physician/first aider/if you feel unwell.P333 P313If skin irritation or rash occurs: Get medical advice/attention.P362 P364Take off contaminated clothing and wash it before reuse.P391P304 P340Collect spillage.IF INHALED: Remove person to fresh air and keep comfortable for breathing.Precautionary statement(s) StorageP405P403 P233Store locked up.Store in a well-ventilated place. Keep container tightly closed.Precautionary statement(s) DisposalP501Dispose of contents/container in accordance with local regulations.SECTION 3 COMPOSITION / INFORMATION ON INGREDIENTSSubstancesSee section below for composition of MixturesMixturesCAS No%[weight]Name64742-94-570-85solvent naphtha petroleum, heavy aromatic138-86-314-30dipenteneSECTION 4 FIRST-AID MEASURESDescription of first aid measuresEye ContactSkin ContactIf this product comes in contact with the eyes:Wash out immediately with fresh running water.Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and moving the eyelids by occasionally lifting the upper and lower lids.Seek medical attention without delay; if pain persists or recurs seek medical attention.Removal of contact lenses after an eye injury should only be undertaken by skilled personnel.If skin contact occurs:Immediately remove all contaminated clothing, including footwear.Flush skin and hair with running water (and soap if available).Seek medical attention in event of irritation.InhalationIf fumes or combustion products are inhaled remove from contaminated area.Lay patient down. Keep warm and rested.Prostheses such as false teeth, which may block airway, should be removed, where possible, prior to initiating first aid procedures.Apply artificial respiration if not breathing, preferably with a demand valve resuscitator, bag-valve mask device, or pocket mask as trained. Perform CPR ifnecessary.Transport to hospital, or doctor.IngestionIf swallowed do NOT induce vomiting.If vomiting occurs, lean patient forward or place on left side (head-down position, if possible) to maintain open airway and prevent aspiration.Observe the patient carefully.Never give liquid to a person showing signs of being sleepy or with reduced awareness; i.e. becoming unconscious.Give water to rinse out mouth, then provide liquid slowly and as much as casualty can comfortably drink.Seek medical advice.Avoid giving milk or oils.Avoid giving alcohol.If spontaneous vomiting appears imminent or occurs, hold patient's head down, lower than their hips to help avoid possible aspiration of vomitus.Indication of any immediate medical attention and special treatment neededFor acute or short term repeated exposures to petroleum distillates or related hydrocarbons:Continued.
Chemwatch: 24-0214Page 3 of 12Version No: 5.1.1.1SNC 2000Issue Date: 02/10/2017Print Date: 12/06/2018Primary threat to life, from pure petroleum distillate ingestion and/or inhalation, is respiratory failure.Patients should be quickly evaluated for signs of respiratory distress (e.g. cyanosis, tachypnoea, intercostal retraction, obtundation) and given oxygen. Patients with inadequate tidal volumes orpoor arterial blood gases (pO2 50 mm Hg) should be intubated.Arrhythmias complicate some hydrocarbon ingestion and/or inhalation and electrocardiographic evidence of myocardial injury has been reported; intravenous lines and cardiac monitors shouldbe established in obviously symptomatic patients. The lungs excrete inhaled solvents, so that hyperventilation improves clearance.A chest x-ray should be taken immediately after stabilisation of breathing and circulation to document aspiration and detect the presence of pneumothorax.Epinephrine (adrenalin) is not recommended for treatment of bronchospasm because of potential myocardial sensitisation to catecholamines. Inhaled cardioselective bronchodilators (e.g.Alupent, Salbutamol) are the preferred agents, with aminophylline a second choice.Lavage is indicated in patients who require decontamination; ensure use of cuffed endotracheal tube in adult patients. [Ellenhorn and Barceloux: Medical Toxicology]Any material aspirated during vomiting may produce lung injury. Therefore emesis should not be induced mechanically or pharmacologically. Mechanical means should be used if it is considerednecessary to evacuate the stomach contents; these include gastric lavage after endotracheal intubation. If spontaneous vomiting has occurred after ingestion, the patient should be monitored fordifficult breathing, as adverse effects of aspiration into the lungs may be delayed up to 48 hours.SECTION 5 FIRE-FIGHTING MEASURESExtinguishing mediaFoam.Dry chemical powder.BCF (where regulations permit).Carbon dioxide.Water spray or fog - Large fires only.Special hazards arising from the substrate or mixtureFire IncompatibilityAvoid contamination with oxidising agents i.e. nitrates, oxidising acids, chlorine bleaches, pool chlorine etc. as ignition may resultSpecial protective equipment and precautions for fire-fightersFire FightingFire/Explosion HazardAlert Fire Brigade and tell them location and nature of hazard.Wear full body protective clothing with breathing apparatus.Prevent, by any means available, spillage from entering drains or water course.Use water delivered as a fine spray to control fire and cool adjacent area.Avoid spraying water onto liquid pools.DO NOT approach containers suspected to be hot.Cool fire exposed containers with water spray from a protected location.If safe to do so, remove containers from path of fire.Combustible.Slight fire hazard when exposed to heat or flame.Heating may cause expansion or decomposition leading to violent rupture of containers.On combustion, may emit toxic fumes of carbon monoxide (CO).May emit acrid smoke.Mists containing combustible materials may be explosive.Combustion products include:,carbon dioxide (CO2),other pyrolysis products typical of burning organic material.WARNING: Long standing in contact with air and light may result in the formationof potentially explosive peroxides.SECTION 6 ACCIDENTAL RELEASE MEASURESPersonal precautions, protective equipment and emergency proceduresSee section 8Environmental precautionsSee section 12Methods and material for containment and cleaning upMinor SpillsEnvironmental hazard - contain spillage.Clean up all spills immediately.Avoid breathing vapours and contact with skin and eyes.Control personal contact with the substance, by using protective equipment.Contain and absorb spill with sand, earth, inert material or vermiculite.Wipe up.Place in a suitable, labelled container for waste disposal.Major SpillsEnvironmental hazard - contain spillage.Moderate hazard.Clear area of personnel and move upwind.Alert Fire Brigade and tell them location and nature of hazard.Wear breathing apparatus plus protective gloves.Prevent, by any means available, spillage from entering drains or water course.No smoking, naked lights or ignition sources.Increase ventilation.Stop leak if safe to do so.Contain spill with sand, earth or vermiculite.Collect recoverable product into labelled containers for recycling.Absorb remaining product with sand, earth or vermiculite.Collect solid residues and seal in labelled drums for disposal.Wash area and prevent runoff into drains.If contamination of drains or waterways occurs, advise emergency services.Continued.
Chemwatch: 24-0214Page 4 of 12Version No: 5.1.1.1Issue Date: 02/10/2017Print Date: 12/06/2018SNC 2000Personal Protective Equipment advice is contained in Section 8 of the SDS.SECTION 7 HANDLING AND STORAGEPrecautions for safe handlingSafe handlingOther informationDO NOT allow clothing wet with material to stay in contact with skinAvoid all personal contact, including inhalation.Wear protective clothing when risk of exposure occurs.Use in a well-ventilated area.Prevent concentration in hollows and sumps.DO NOT enter confined spaces until atmosphere has been checked.Avoid smoking, naked lights or ignition sources.Avoid contact with incompatible materials.When handling, DO NOT eat, drink or smoke.Keep containers securely sealed when not in use.Avoid physical damage to containers.Always wash hands with soap and water after handling.Work clothes should be laundered separately.Use good occupational work practice.Observe manufacturer's storage and handling recommendations contained within this SDS.Atmosphere should be regularly checked against established exposure standards to ensure safe working conditions.Store in original containers.Keep containers securely sealed.No smoking, naked lights or ignition sources.Store in a cool, dry, well-ventilated area.Store away from incompatible materials and foodstuff containers.Protect containers against physical damage and check regularly for leaks.Observe manufacturer's storage and handling recommendations contained within this SDS.Conditions for safe storage, including any incompatibilitiesSuitable containerStorage incompatibilityMetal can or drumPackaging as recommended by manufacturer.Check all containers are clearly labelled and free from leaks.Avoid reaction with oxidising agentsSECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTIONControl parametersOCCUPATIONAL EXPOSURE LIMITS (OEL)INGREDIENT DATASourceIngredientMaterial nameTWASTELPeakNotesCanada - Alberta OccupationalExposure LimitsdipenteneTurpentine and selected monoterpenes20 ppm / 111 mg/m3Not AvailableNot AvailableNot AvailableEMERGENCY LIMITSIngredientMaterial nameTEEL-1TEEL-2TEEL-3SNC 2000Not AvailableNot AvailableNot AvailableNot AvailableIngredientOriginal IDLHRevised IDLHsolvent naphtha petroleum, heavyaromaticNot AvailableNot AvailabledipenteneNot AvailableNot AvailableMATERIAL DATANOTE M: The classification as a carcinogen need not apply if it can be shown that the substance contains less than 0.005% w/w benzo[a]pyrene (EINECS No 200-028-5). This note applies only tocertain complex oil-derived substances in Annex IV.European Union (EU) List of harmonised classification and labelling hazardous substances, Table 3.1, Annex VI, Regulation (EC) No 1272/2008 (CLP) - up tothe latest ATPExposure controlsEngineering controls are used to remove a hazard or place a barrier between the worker and the hazard. Well-designed engineering controls can behighly effective in protecting workers and will typically be independent of worker interactions to provide this high level of protection.The basic types of engineering controls are:Process controls which involve changing the way a job activity or process is done to reduce the risk.Enclosure and/or isolation of emission source which keeps a selected hazard "physically" away from the worker and ventilation that strategically "adds" and"removes" air in the work environment. Ventilation can remove or dilute an air contaminant if designed properly. The design of a ventilation system mustmatch the particular process and chemical or contaminant in use.Employers may need to use multiple types of controls to prevent employee overexposure.Appropriate engineeringcontrolsLocal exhaust ventilation usually required. If risk of overexposure exists, wear approved respirator. Correct fit is essential to obtain adequate protection.Supplied-air type respirator may be required in special circumstances. Correct fit is essential to ensure adequate protection.An approved self contained breathing apparatus (SCBA) may be required in some situations.Provide adequate ventilation in warehouse or closed storage area. Air contaminants generated in the workplace possess varying "escape" velocities which,in turn, determine the "capture velocities" of fresh circulating air required to effectively remove the contaminant.Type of Contaminant:Air Speed:Continued.
Chemwatch: 24-0214Page 5 of 12Version No: 5.1.1.1Issue Date: 02/10/2017Print Date: 12/06/2018SNC 2000solvent, vapours, degreasing etc., evaporating from tank (in still air).0.25-0.5 m/s (50-100f/min.)aerosols, fumes from pouring operations, intermittent container filling, low speed conveyer transfers, welding, spray drift, platingacid fumes, pickling (released at low velocity into zone of active generation)0.5-1 m/s (100-200f/min.)direct spray, spray painting in shallow booths, drum filling, conveyer loading, crusher dusts, gas discharge (active generationinto zone of rapid air motion)1-2.5 m/s (200-500f/min.)grinding, abrasive blasting, tumbling, high speed wheel generated dusts (released at high initial velocity into zone of very highrapid air motion).2.5-10 m/s(500-2000 f/min.)Within each range the appropriate value depends on:Lower end of the rangeUpper end of the range1: Room air currents minimal or favourable to capture1: Disturbing room air currents2: Contaminants of low toxicity or of nuisance value only.2: Contaminants of high toxicity3: Intermittent, low production.3: High production, heavy use4: Large hood or large air mass in motion4: Small hood-local control onlySimple theory shows that air velocity falls rapidly with distance away from the opening of a simple extraction pipe. Velocity generally decreases with thesquare of distance from the extraction point (in simple cases). Therefore the air speed at the extraction point should be adjusted, accordingly, afterreference to distance from the contaminating source. The air velocity at the extraction fan, for example, should be a minimum of 1-2 m/s (200-400 f/min) forextraction of solvents generated in a tank 2 meters distant from the extraction point. Other mechanical considerations, producing performance deficits withinthe extraction apparatus, make it essential that theoretical air velocities are multiplied by factors of 10 or more when extraction systems are installed or used.Personal protectionEye and face protectionSkin protectionHands/feet protectionBody protectionSafety glasses with side shields.Chemical goggles.Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. A written policy document, describing the wearingof lenses or restrictions on use, should be created for each workplace or task. This should include a review of lens absorption and adsorption for theclass of chemicals in use and an account of injury experience. Medical and first-aid personnel should be trained in their removal and suitable equipmentshould be readily available. In the event of chemical exposure, begin eye irrigation immediately and remove contact lens as soon as practicable. Lensshould be removed at the first signs of eye redness or irritation - lens should be removed in a clean environment only after workers have washed handsthoroughly. [CDC NIOSH Current Intelligence Bulletin 59], [AS/NZS 1336 or national equivalent]See Hand protection belowWear chemical protective gloves, e.g. PVC.Wear safety footwear or safety gumboots, e.g. RubberNOTE:The material may produce skin sensitisation in predisposed individuals. Care must be taken, when removing gloves and other protective equipment, toavoid all possible skin contact.Contaminated leather items, such as shoes, belts and watch-bands should be removed and destroyed.The selection of suitable gloves does not only depend on the material, but also on further marks of quality which vary from manufacturer to manufacturer.Where the chemical is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to bechecked prior to the application.The exact break through time for substances has to be obtained from the manufacturer of the protective gloves and.has to be observed when making a finalchoice.Personal hygiene is a key element of effective hand care. Gloves must only be worn on clean hands. After using gloves, hands should be washed and driedthoroughly. Application of a non-perfumed moisturiser is recommended.Suitability and durability of glove type is dependent on usage. Important factors in the selection of gloves include:·frequency and duration of contact,·chemical resistance of glove material,·glove thickness and·dexteritySelect gloves tested to a relevant standard (e.g. Europe EN 374, US F739, AS/NZS 2161.1 or national equivalent).·When prolonged or frequently repeated contact may occur, a glove with a protection class of 5 or higher (breakthrough time greater than240 minutes according to EN 374, AS/NZS 2161.10.1 or national equivalent) is recommended.·When only brief contact is expected, a glove with a protection class of 3 or higher (breakthrough time greater than 60 minutes accordingto EN 374, AS/NZS 2161.10.1 or national equivalent) is recommended.·Some glove polymer types are less affected by movement and this should be taken into account when considering gloves for long-termuse.·Contaminated gloves should be replaced.As defined in ASTM F-739-96 in any application, gloves are rated as:·Excellent when breakthrough time 480 min·Good when breakthrough time 20 min·Fair when breakthrough time 20 min·Poor wh
Drew Marine SNC 2000 Chemwatch: 24-0214 Version No: 5.1.1.1 Safety Data Sheet according to WHMIS 2015 requirements Issue Date: 02/10/2017 Print Date: 12/06/2018
Drew Marine Caustic Potash DM R R R R R NR Drew Marine Caustic Soda DM R R R R R NR Drew Marine DREW ABD R R R R R NR Drew Marine Drew BC R R R R R R Drew Marine DREW NBD R R R R R R Revision 5, January 4, 2018 2. Jot
POA created Confirming date and qty SNC Enter consumption of components SNC Submit ASN (Mass Upload) SNC IBD Goods Receipt OBD Goods Issue Invoice process in VIM/ERP Subcon invoice Supplier Payment Run Receipt of Payment / Status Updates in SNC SNC Delivery, Pick, Pack DC Update prices i
Registered company name Drew Marine Address 100 South Jefferson Road NJ 07981 United States Telephone 973 526-5700 Fax Not Available Website www.drew-marine.com Email info@drew-marine.com Emergency phone number Association / Organisation Not Available Emergency telephone numbers The numbers below are for EMERGENCY USE ONLY.File Size: 303KBPage Count: 11
3E Online - SDS Flexible, scalable, efficient online SDS management for companies of all sizes and industries. Silver Gold Platinum Overview 3E Online-SDS is a powerful combination of outsourced services and an easy-to-use web-based application providing access to a customer’s chemical inventory and associated Safety Data Sheets (SDSs) 24-7 .File Size: 918KBPage Count: 8Explore furtherProduct: 3E SDS - Free SDS searchwww.msds.comSafety Data Sheets Free SDS Database Chemical Safetychemicalsafety.comSDS Management Information Request - 3E Companyoffers.3ecompany.com3EiQ - Home Pagewww.3eonline.comSDS and Chemical Management - Verisk 3Ewww.verisk3e.comRecommended to you b
DREW ELECTRIC 2000 Chemwatch: 93-3301 Version No: 2.1.1.1 Safety Data Sheet according to WHMIS 2015 requirements Issue Date: 20/02/2018 Print Date: 12/06/2018 L.GHS.CAN.EN SECTION 1 IDENTIFICATION Product Identifier Product name DREW ELECTRIC 2000 Other means of identification Not Available Recommended use of the chemical and restrictions on use
From Pros for Pros www.keil.eu 9 HAMMER DRILL BITS PROFESSIONAL WORK MEANS ECONOMICAL WORK HAMMER DRILL BITS 251 SDS-plus MS5 TURBOHEAD Xpro 12-15 252 SDS-plus W2 TURBOKEIL X-Form 16 253 SDS-plus MS5 TURBOKEIL 17-20 255 SDS-plus MS5 VARIO 21 256 SDS-plus hammer drill bit KEILRAPID 22 270 SDS-max W2 TURBOHEAD Xpro / TURBOKEIL X-Form 23-26
4 St. Norbert College Hockey Yearbook 2019-20 Experience all that St. Norbert College has to offer! Apply today for Fall 2020 at snc.edu/go/apply. Office of Admission 800-236-4878 admit@snc.edu www.snc.edu Pursue what matters at St. Norbert College Student-faculty collaborations that set you apart from your peers.
I am My Brother’s Keeper (2004) As our New Year’s celebration draws near, I once again find myself pondering the enigmatic story that our tradition places before us at this time—the story of the Binding of Isaac. Once again, I walk for those three long days with father Abraham and ponder the meaning of his journey with his son to the mountain. And once again, I find fresh meaning in the .
