INSTALLATION MANUAL HEIGHT ADJUSTABLE TABLE: TWO LEG KIT
INSTALLATION MANUALHEIGHT ADJUSTABLE TABLE: TWO LEG KITTCSS180 Rev. E
ContentsHardware List and Tools Required / Warnings/Disclaimer.2Installation Instructions - STEP 1 - STEP 8. 3Installation Instructions - STEP 9 - STEP 11. 44-Position Memory Control. 4B10.39Hardware List and Tools RequiredNUMBERITEMQTY.TOOL REQUIRED4.16M6 x 15 BoltA22.87#W 10 XOO 7/8DSC " LREWBC4 pieces5mm Allen KeyM4 x 25Phillips Screw2 pieces#2 Phillips Screw Driver#10 x 7/8" LPhillips Screw18 pieces#2 Phillips Screw Driver8 pieces5mm Allen Key4 piecesN/A4 pieces4mm Allen Key2 piecesN/AM10 x 35 BoltDLevelerESet ScrewFTop SpacerGWarnings/DisclaimersINSTALLATION WARNINGS: Read the entire instruction manual before beginning any installation or assembly.Improper installation of this product may cause extensive property damageor serious personal injury, either during or after installation.DISCLAIMER: The manufacturer will bear no responsibility for any damages of any kindarising from improper installation of this product.Work surfaces will vary widely and the ultimate method of installingis out of the manufacturers control. It is imperative that the installer consultthe work surface installation guide to ensure that it can safely handle theapplied load.2 Installation Manual: HEIGHT ADJUSTABLE TABLE: Two Leg KitADJUSTMENT NOTIFICATION: Routine maintenance checks and adjustments are suggested to properlysupport the quality and optimal performance of this product.Over tightening of bolts during installation or adjustments can damagethe product and affect the function and warranty.
Installation InstructionsSTEP 1Remove base from box.STEP 2STEP 3STEP 5STEP 6Place the table leg frame on the bottom sideof the table top.A. Apply Top Spacers toadjustable-width portionof crossbar by removingstandard grommets fromcenter support rails.Slide the Side Support Brackets into the left andright ends of the table leg frame. The bracketsmust be fully inserted into the frame. A rubbermallet may be needed to complete engagement.B. Install Top Spacers intocenter support rails.Top SpacerGSTEP 4Lift each leg into the final vertical position andtighten the already installed screws.Insert 4 x Bolt A through the sides of the tableleg frame to secure the side support brackets.Adjust the width of the table leg frame to fitthe table top.Use 5 mmAllen Key totighten.Use 5 mmAllen Key totighten.Bolt ASTEP 710.39A. Secure the table leg frame to the tabletop with 18 x Screw C.STEP 8Tighten the 4 x pre-installed Set Screw Fon the inner side of the table leg frame.Use 4 mmAllen Key totighten.BUse a #2 PhillipsScrewdriver totighten.STEP 9Place the table feet onto the ends of the legs.(Ensure the feet are facing the correct direction).Use 8 x Bolt D to secure the feet to the legs.The Levelers will have to be adjusted once the tableis upright to ensure the table is level and stable.4.1622.87#10 X 7/8" LWOOD SCREWScrew CScrew FBolt DUse 5 mm AllenKey to tighten.Screw BHeight Adjustablecontroller holder.LevelerB. Position the Height Adjustable controller in thefinal desired location at the edge of the tabletop. Secure to the table top with 2 x Screw B.Installation Manual: HEIGHT ADJUSTABLE TABLE: Two Leg Kit3
Installation InstructionsSTEP 10Connect the height adjustment controller cableto the table controller.STEP 11Connect the power cable to the controller.STEP 12Flip the table over. Reset the 4-Position MemoryController before use.Digital SwitchA RESET ***PERFORM RESET BEFORE FIRST USE***1. Clear the area under and around the table.2. Press bothandbuttons at the same time until the table is in its lowest position.3. The display on the height adjustment controller will show "000" while conducting reset.4. When height adjustment controller beeps, the buttons can be released and reset is complete.NOTE: If Collision Detection feature is activated by table contacting an object, the reset function will need to be performed.B NORMAL OPERATION1.2.3.Press any button and the display shows current height in inches (in).Press and holdorbutton to adjust the height.When no button has been pressed for 30 seconds, the system goes to 0.1 W standby mode, and the display turns off.Press any button to wake the system and display the current base height.C CALIBRATE1.2.3.4.The default starting height for an Extended Electric table is approximately 25", and for a Standard Electric table 27.5".Press thebutton until reaching lowest position. At the lowest position, pressbutton again for 5 secondsuntil display starts flashing for 10 seconds.Immediately, pressorbuttons to display the measured table height. Then pressandbuttons togetherfor 3 seconds to store this position.Display stops flashing and the new starting height is shown in the display.4 Installation Manual: HEIGHT ADJUSTABLE TABLE: Two Leg Kit
D MEMORY PRESETS1.2.3.4.Operate the desk to preferred height.2 3 4 together withPress any of 1 ①②③④orfor 2 seconds to store the current height.Display shows P1/P2/P3/P4 when the position has been stored.To return table/desk to a stored position, hold the memory preset button 1①②③④ 2 3 4 until the desk reaches the stored height.Memory presets can be overwritten with a new position at any time.E UPPER LIMIT1. Move the table to the preferred upper limit.2. Press and together, and release within 3 seconds (before Reset is initiated).3. Continue to hold the Button for 5 secondsF LOWER LIMIT1. Move the table to the preferred lower limit.2. Press and together, and release within 3 seconds (before Reset is initiated).3. Continue to hold the Button for 5 seconds.G UNDO UPPER LIMIT PROGRAMMING1. Raise table to programmed upper limit.2. Press and together, and release within 3 seconds (before Reset is initiated).3. Continue to hold the Button for 5 seconds.H UNDO LOWER LIMIT PROGRAMMING1. Lower table to programmed lower limit.2. Press and together, and release within 3 seconds (before Reset is initiated).3. Continue to hold the Button for 5 seconds.I RESET1. If a reset is required, proceed to Section A.NOTE: The table will travel to its lowest factory setting during a reset so ensure the area under the table is clear.TCSS180 Rev. E
final desired location at the edge of the table top. Secure to the table top with 2 x Screw B. Height Adjustable Screw B Use 4 mm Allen Key to Screw F controller holder. B 10.39 4 22.87.16 #10 X 7/8" L WOOD SCREW STEP 9 Place the table feet onto the ends of the legs. (Ensure the feet are facing the correct direction).
minimum mounting height: 15'-0" permitted sigh height: the mmh sign itself b. permitted sign area: 40 sf minimum mounting height: 15'-0" permitted sigh height: 16'-0" maximum height maximum sign height needs to be adjusted 6'-0" maximum sign height 7'-0" minimum mounting height c. permitted sign height: 6'-0" monument .
lugano collection ttache orma ey overall width overall depth overall height frame height seat height arm height foot height seat height (floor to cushion seam) seat height (floor to frame) inside seat width inside seat depth w/ back cushion inside seat depth w/o back cushion inside back height w/ seat & back cushions inside back height
Mitsubishi Diamana S 60 Regular 60 Mid Mid Stiff 61 Mid Mid DRIVER SPECS STOCK GRAPHITE SHAFT Loft Length Lie Left-hand 9 (Adjustable) 45.5" Adjustable Yes 10.5 (Adjustable) 45.5" Adjustable Yes 12 (Adjustable) 45.5" Adjustable Yes Model Flex Weight (grams) Torque Kick Point Fujiku
2 1-800-349-3839 info@upliftdesk.com www.upliftdesk.com This height adjustable desk has an electric motor and is designed for use in dry work areas only. The desk height is adjustable so that it can
SC11006 6" Adjustable Wrench SC11008 8" Adjustable Wrench SC11010 10" Adjustable Wrench SC11012 12" Adjustable Wrench SC11015 15" Adjustable Wrench SC12001A 7-Piece Hex Wrench Set, Ball Style (SAE) SC12501A 9-Piece Hex Wrench Set, Ball Style (Metric) SC13016 Ball Peen Hammer, 16 oz. SC1
maxwell collection ttache orma ey overall width overall depth overall height frame height seat height arm height foot height seat height (floor to cushion seam) seat height (floor to frame) inside seat width inside seat depth
Cosm Work Chairs 6 Cosm Chairs Price Book (10/22) HermanMiller Cosm Work Chair continued Specification Information Step 1. FLC1 Step 2. Back Height 4 low back height 1545 5 mid back height 1609 6 high back height 1705 Step 3. Height Adjustment 2 standard-height range 0 3 high-height range 0 Step 4. Tilt S auto-harmonic tilt 0 Step 5. Seat Depth
Advanced level Speciflcation summary 1. 2 Advanced level Speciflcation summary Qualification objective CIPD Advanced level qualifications provide a depth of knowledge alongside the opportunity to specialise in chosen areas of expertise. Candidates will be able to develop their understanding of organisations and the external context within which HR operates. Using critical analysis, self .
