FORMULARY INDUSTRIAL MAINTENANCE COATINGS No. 502

2y ago
152 Views
2 Downloads
4.94 MB
17 Pages
Last View : 10d ago
Last Download : 9m ago
Upload by : Amalia Wilborn
Transcription

FORMULARYINDUSTRIAL MAINTENANCE COATINGSNo. 502

FORMULARYPaint & Paper DepartmentNo. 502Industrial Maintenance Coatings FormularyACTIV-8 Drier, Stabilizer and Accelerator is a solution of 1,10-phenanthroline, a chelating agentfor metals. ACTIV-8 acts as drier accelerator and stabilizer when used with cobalt and/ ormanganese driers in paints and coatings based on oleoresinous binders. A ratio of 10 parts ofACTIV-8 to 1 part of drier metal is most often used in solvent-borne coatings. ACTIV-8 does notaffect the activity of the other commonly used drier metals. ACTIV-8 is used in combination withmanganese and/or cobalt driers in coatings that cure by oxidative polymerization. In general,ACTIV-8 is used with manganese and cobalt in solvent-borne coatings. The surface dryingactivity of manganese is accelerated to a much greater degree than that of cobalt. The activitywith cobalt improves through dry and long term aging stability, especially in waterborne coatingswhere loss of dry often occurs. DARVAN 7-N Dispersant is a sodium polymethacrylate, a clear to slightly opalescent colorlessliquid. It shows very little tendency to foam. It is used as a dispersant for minerals and pigments inthe dispersion portion of manufacture of water based paints and coatings.DARVAN C-N Dispersant is an ammonium polyacrylate dispersing agent for minerals andextenders for water-based paints. DARVAN C-N has good zinc oxide stability and inhibits gelformation.VANSIL W Wollastonite is a calcium metasilicate mineral, available in five grades of fineness tomeet the requirements of the coatings industry. Each grade exhibits a lower viscosity in paint thanis indicated by its oil absorption value. The relatively high pH (10-11) of VANSIL W is particularlyuseful in maintaining the desired alkaline pH level of latex paints and preventing the early rustingof latex maintenance coatings. VANSIL W is an excellent extender pigment for powder coatingsas well as solvent-thinned and latex paints. VANSIL W-50 disperses to a 6 to 7 Hegman finenessat three pounds per gallon. This grade is suitable for liquid industrial and corrosion resistantcoatings, powder coatings, and semi-gloss architectural coatings. In powder coatings, this gradeis desirable for smoother films and improved gloss.ACTIV-8 Drier, Stabilizer and Accelerator, DARVAN Dispersant and VANSIL Wollastonite are registered trademarks ofR.T. Vanderbilt Holding Company, Inc. and/or its respective wholly owned subsidiaries.rev09/10/2013Before using, read, understand and comply with the information and precautions in the Safety Data Sheets, label and other product literature. The information presented herein, while not guaranteed,was prepared by technical personnel and, to the best of our knowledge and belief, is true and accurate as of the date hereof. No warranty, representation or guarantee, express or implied, is maderegarding accuracy, performance, stability, reliability or use. This information is not intended to be all-inclusive, because the manner and conditions of use, handling, storage and other factors may involveother or additional safety or performance considerations. The user is responsible for determining the suitability of any material for a specific purpose and for adopting such safety precautions as maybe required. Vanderbilt Minerals, LLC does not warrant the results to be obtained in using any material, and disclaims all liability with respect to the use, handling or further processing of any such material.No suggestion for use is intended as, and nothing herein shall be construed as, a recommendation to infringe any existing patent, trademark or copyright or to violate any federal, state or local law orregulation.

PROTOTYPE FORMULAFormula 081501Water-Reducible Alkyd/Acrylic Latex Direct To Metal PrimerVANSIL W-501 Wollastonite, ACTIV-8 1 Drier, Stabilizer and AcceleratorPoundsDISPERSION65.6Kelsol 3961-B2G-75228.1Arcosolv DPM3Preblend the next four items and add.23.4Arcosolv DPM4.7Arcosolv PM Acetate30.4ACTIV-81 Drier, Stabilizer and AcceleratorCobalt Hydrocure II41.546.8Ti-Pure R 9005VANSIL W-501 Wollastonite76.1Halox SW 111674.9Disperse at high speed for 20 minutes.Reduce speed and add:1.9AMP-95 7Water57.5Measure pH and adjust to 8.0 to 8.5 with AMP-95.Mix at slow speed for 5 minutes.LET DOWN2.5% Cellosize QP 44008Mix at medium speed for 5 minutes.NeoCryl 6085 Latex9Mix at slow speed for 10 100.0117.49100.01PAINT PROPERTIESDensity% Solids by weight% Solids by volume% PVCPigment to binder ratioCalculated VOC9.8 lbs/gal44.833.4230.82:11.72 lbs/gal1.17 g/ml205 g/lRAW MATERIAL SUPPLIERSTRADEMARKS1Registered and pending trademarks appearing printed in bold in these materials are thoseof Vanderbilt Minerals, LLC. For a complete listing, please visitVanderbilt Minerals, LLC, Norwalk, CT2Reichhold, Inc., Research Triangle Park, NC3Lyondell Chemical Company, Rotterdam, The Netherlands4OM Group, Inc., Cleveland, OH5E.I. DuPont de Nemours & Company, Wilmington, DE6Halox Pigments, Hammond, IN7Angus Chemical Company, Buffalo Grove, IL8Dow Chemical Company, Midland, MI9AstraZeneca Pharmaceuticals LP, Wilmington, DEhttp://www.vanderbiltminerals.com/ee content/Documents/Technical/Trademarks VM Web.pdfAMP-95 is a registered trademark of Angus Chemical Company.Acrysol is a registered trademark of Rohm & Haas Company.Cellosize is a registered trademark of Union Carbide Chemicals & Plastics TechnologyCorporation.Cobalt Hydrocure is a registered trademark of OM Group, Inc.Halox is a registered trademark of Halox Pigments.Kelsol is a registered trademark of Reichhold Chemical, Inc.NeoCryl is a registered trademark of DSM NeoResins B.V.Ti-Pure is a registered trademark of E.I. DuPont de Nemours & Company.Rev02/19/2013Before using, read, understand and comply with the information and precautions in the Safety Data Sheets, label and other product literature. The information presented herein, while not guaranteed,was prepared by technical personnel and, to the best of our knowledge and belief, is true and accurate as of the date hereof. No warranty, representation or guarantee, express or implied, is maderegarding accuracy, performance, stability, reliability or use. This information is not intended to be all-inclusive, because the manner and conditions of use, handling, storage and other factors may involveother or additional safety or performance considerations. The user is responsible for determining the suitability of any material for a specific purpose and for adopting such safety precautions as maybe required. Vanderbilt Minerals, LLC does not warrant the results to be obtained in using any material, and disclaims all liability with respect to the use, handling or further processing of any such material.No suggestion for use is intended as, and nothing herein shall be construed as, a recommendation to infringe any existing patent, trademark or copyright or to violate any federal, state or local law orregulation.

PROTOTYPE FORMULAFormula 0821012K Water-borne Epoxy Fast Dry Shop PrimerVANSIL W-501 WollastonitePoundsGallonsPART A334.337.1Epi-Rez 5522-WY-552Diacetone Alcohol7.30.93.60.4Rhodoline 6403Water60.87.372.11.7Mapico 214 M4Barytes72.11.9VANSIL W-501 Wollastonite107.94.5Moly-White 2125101.54.172.13.1Talcron 40 LOA Talc6325 mesh wet ground mica7.70.3Disperse at high speed for 15 minutes. Reduce speed for let down.149.016.6Epi-Rez 5522-WY-552Water14.51.7Mix at slow speed for 5 minutes.TOTALS PARTS 913.47.3513.396.9313.39Totals PART B172.9Add PART B to PART A, mix well, let stand 1 hour prior to use.20.320.7420.32Totals PART A plus PART B99.9141.09100.01PART BEpi-Cure 8290-Y-602WaterMix at slow speed for 5 minutes.1175.8PAINT PROPERTIES (PART A plus PART B)Density% Solids by weight% Solids by volume% PVCPigment to binder ratioCalculated VOC11.8 lbs/gal62.947.033.31.42:11.11 lbs/gal1.41 g/ml133 g/lRAW MATERIAL SUPPLIERSTRADEMARKS1Registered and pending trademarks appearing printed in bold in these materials are thoseof Vanderbilt Minerals, LLC. For a complete listing, please visitVanderbilt Minerals, LLC, Norwalk, CT2Hexion Specialty Chemicals, Houston, TX3Rhodia Inc., Cranbury, NJ4Rockwood Pigments NA, Inc., Beltsville, MD5Moly-White Pigments Group, Cleveland, OH6Specialty Minerals, Inc., Barretts, MThttp://www.vanderbiltminerals.com/ee content/Documents/Technical/Trademarks VM Web.pdfEpi-Cure and Epi-Rez are registered trademarks of Resolution Performance Products.Mapico is a registered trademark of Rockwood Pigments NA, Inc.Moly-White is a registered trademark of SWIMC, Inc.Rhodoline is a registered trademark of Rhodia.Talcron is a registered trademark of Minerals Technologies Inc.Rev02/19/2013Before using, read, understand and comply with the information and precautions in the Safety Data Sheets, label and other product literature. The information presented herein, while not guaranteed,was prepared by technical personnel and, to the best of our knowledge and belief, is true and accurate as of the date hereof. No warranty, representation or guarantee, express or implied, is maderegarding accuracy, performance, stability, reliability or use. This information is not intended to be all-inclusive, because the manner and conditions of use, handling, storage and other factors may involveother or additional safety or performance considerations. The user is responsible for determining the suitability of any material for a specific purpose and for adopting such safety precautions as maybe required. Vanderbilt Minerals, LLC does not warrant the results to be obtained in using any material, and disclaims all liability with respect to the use, handling or further processing of any such material.No suggestion for use is intended as, and nothing herein shall be construed as, a recommendation to infringe any existing patent, trademark or copyright or to violate any federal, state or local law orregulation.

PROTOTYPE FORMULAFormula 111808Interior Floor CoatingDARVAN 7-N1 Dispersant, VANSIL W-501 WollastoniteDISPERSIONWaterIgepal CO 6302Soya LecithinDARVAN 7-N1 DispersantDrewplus L 4753Ti-Pure R 9024ATTAGEL 505VANSIL W-501 WollastoniteHigh speed disperse for 20 minutes. Set 0.130.20124.89100.02LET DOWN19.2Water160.0370.042.1Aquamac 450 Latex61.50.2Drewplus L 4753Add dispersion while mixing at medium speed.Preblend the next five items, mix at slow speed for 1 minute and add:Ethylene Glycol5.00.515.01.9Texanol 7Butyl Carbitol 84.00.510.01.1Acrysol RM 2020 NPR910.01.1Acrysol RM 8259Water75.09.02.50.3Polyphobe TR 11681.00.1AMP-95 101.50.2Drewplus L 4753Mix at slow speed for 30 minutes. Post add black tint paste to make the paint gray.TOTALSPAINT PROPERTIESDensity% Solids by weight% Solids by volume% PVCPigment to binder ratioCalculated VOC1041.010.4 lbs/gal43.729.332.51.40:10.68 lbs/gal100.21.25 g/ml81 g/lRAW MATERIAL SUPPLIERSTRADEMARKS1Registered and pending trademarks appearing printed in bold in these materials are thoseof Vanderbilt Minerals, LLC. For a complete listing, please visitVanderbilt Minerals, LLC, Norwalk, CT2Rhodia Inc., Cranbury, NJ3Ashland Chemical Company, Covington, KY4E.I. DuPont de Nemours & Company, Wilmington, DE5BASF Corporation, Florham Park, NJ6Hexion Specialty Chemicals, Houston, TX7Eastman Chemical Company, Kingsport, TN8Dow Chemical Company, Midland, MI9Rohm & Haas Company, Philadelphia, PA10Angus Chemical Company, Buffalo Grove, ILhttp://www.vanderbiltminerals.com/ee content/Documents/Technical/Trademarks VM Web.pdfAcrysol is a registered trademark of Rohm & Haas Company.AMP-95 is a registered trademark of Angus Chemical Company.Aquamac is a registered trademark of Resolution Specialty Materials.ATTAGEL is a trademark of BASF Catalysts LLC.Carbitol and Polyphobe are registered trademarks of Union Carbide Chemicals & PlasticsTechnology Corporation.Drewplus is a registered trademark of Ashland Licensing and Intellectual Property LLC.Igepal is a registered trademark of Rhodia.Texanol is a registered trademark of Eastman Chemical Company.Ti-Pure is a registered trademark of E.I. DuPont de Nemours & Company.Rev02/19/2013Before using, read, understand and comply with the information and precautions in the Safety Data Sheets, label and other product literature. The information presented herein, while not guaranteed,was prepared by technical personnel and, to the best of our knowledge and belief, is true and accurate as of the date hereof. No warranty, representation or guarantee, express or implied, is maderegarding accuracy, performance, stability, reliability or use. This information is not intended to be all-inclusive, because the manner and conditions of use, handling, storage and other factors may involveother or additional safety or performance considerations. The user is responsible for determining the suitability of any material for a specific purpose and for adopting such safety precautions as maybe required. Vanderbilt Minerals, LLC does not warrant the results to be obtained in using any material, and disclaims all liability with respect to the use, handling or further processing of any such material.No suggestion for use is intended as, and nothing herein shall be construed as, a recommendation to infringe any existing patent, trademark or copyright or to violate any federal, state or local law orregulation.

PROTOTYPE FORMULAFormula 0620012K Water-Borne Epoxy Fast Dry Shop PrimerVANSIL W-501 WollastonitePoundsGallonsPART A334.337.1Epi-Rez 5522-WY-552Diacetone Alcohol7.30.93.60.4Rhodoline 6403Water60.87.3Red Iron Oxide72.11.772.11.9Huberbrite 4107.94.5VANSIL W-501 Wollastonite101.54.1Moly-White 212572.13.1Zeeospheres G 40067.70.3325 mesh wet ground mica7Disperse at high speed for 15 minutes. Reduce speed for let down.149.016.6Epi-Rez 5522-WY-55214.51.7WaterMix at slow speed for 5 minutes.TOTALS PART .01PART BEpi-Cure 8290-Y-602WaterMix at slow speed for 5 minutes.Totals PART B172.9Add PART B to PART A, mix well, let stand 1 hour prior to use.Totals PART A plus PART B1175.8PAINT PROPERTIES (PART A plus PART B)Density% Solids by weight% Solids by volume% PVCPigment to binder ratioCalculated VOC11.8 lbs/gal62.947.033.31.42:11.11 lbs/gal1.41 g/ml133 g/lRAW MATERIAL SUPPLIERSTRADEMARKS1Registered and pending trademarks appearing printed in bold in these materials are thoseof Vanderbilt Minerals, LLC. For a complete listing, please visitVanderbilt Minerals, LLC, Norwalk, CT2Hexion Specialty Chemicals, Houston, TX3Rhodia Inc., Cranbury, NJ4J.M. Huber Corporation, Edison, NJ5Moly-White Pigment Group, Cleveland, OH63M Company, Minneapolis, MN7KMG Minerals Inc., Kings Mountain, NChttp://www.vanderbiltminerals.com/ee content/Documents/Technical/Trademarks VM Web.pdfEpi-Cure and Epi-Rez are registered trademarks of Resolution Performance Products.Huberbrite is a trademark of J.M. Huber Corporation.Moly-White is a registered trademark of SWIMC,Inc.Rhodoline is a registered trademark of Rhodia.Zeeospheres is a registered trademark of 3M Company.Rev02/19/2013Before using, read, understand and comply with the information and precautions in the Safety Data Sheets, label and other product literature. The information presented herein, while not guaranteed,was prepared by technical personnel and, to the best of our knowledge and belief, is true and accurate as of the date hereof. No warranty, representation or guarantee, express or implied, is maderegarding accuracy, performance, stability, reliability or use. This information is not intended to be all-inclusive, because the manner and conditions of use, handling, storage and other factors may involveother or additional safety or performance considerations. The user is responsible for determining the suitability of any material for a specific purpose and for adopting such safety precautions as maybe required. Vanderbilt Minerals, LLC does not warrant the results to be obtained in using any material, and disclaims all liability with respect to the use, handling or further processing of any such material.No suggestion for use is intended as, and nothing herein shall be construed as, a recommendation to infringe any existing patent, trademark or copyright or to violate any federal, state or local law orregulation.

PROTOTYPE FORMULAFormula 020503Black Gloss Enamel Water-Reducible Alkyd CoatingACTIV-8 1 Drier, Stabilizer and AcceleratorPoundsGallonsGRIND145.016.6Kelsol 3961-B2G-752Preblend the next four items and add:20.02.8Arcosolv PnB320.02.5Calcium sulfonate corrosion inhibitorACTIV-81 Drier, Stabilizer and Accelerator2.00.3Cobalt Hydrocure II44.80.610.01.3AMP-95 5Measure pH and adjust to 8.0 to 8.5 with AMP-95.Mix at slow speed for 5 minutes.Raven 1255617.51.2Water250.730.0Steel ball mill to 7 Hegman fineness. Transfer to let down tank.LET DOWNKelsol 3961-B2G-752AMP-955Adjust pH to 8.0 to 8.5Premix the next two items and add:Arcosolv PnB3WaterMix at slow speed for 10 minutes.TOTALSPAINT PROPERTIESDensity% Solids by weight% Solids by volume% PVCPigment to binder ratioCalculated .68845.299.8101.5699.978.5 lbs/gal25.121.15.70.90:12.71 lbs/gal1.06 g/ml325 g/lRAW MATERIAL SUPPLIERSTRADEMARKS1Registered and pending trademarks appearing printed in bold in these materials arethose of Vanderbilt Minerals, LLC. For a complete listing, please visitVanderbilt Minerals, LLC, Norwalk, CT2Reichhold, Inc., Research Triangle Park, NC3Lyondell Chemical Company, Rotterdam, The Netherlands4OM Group, Inc., Cleveland, OH5Angus Chemical Company, Buffalo Grove, IL6Columbian Chemicals Company, Marietta, GAhttp://www.vanderbiltminerals.com/ee content/Documents/Technical/Trademarks VM Web.pdfAMP-95 is a registered trademark of Angus Chemical Company.Arcosolv is a registered trademark of Lyondell Chemical Company.Cobalt Hydrocure is a registered trademark of OM Group, Inc.Kelsol is a registered trademark of Reichhold Chemical, Inc.Raven is a registered trademark of Columbian Chemical Company.Rev09/10/2013Before using, read, understand and comply with the information and precautions in the Safety Data Sheets, label and other product literature. The information presented herein, while not guaranteed,was prepared by technical personnel and, to the best of our knowledge and belief, is true and accurate as of the date hereof. No warranty, representation or guarantee, express or implied, is maderegarding accuracy, performance, stability, reliability or use. This information is not intended to be all-inclusive, because the manner and conditions of use, handling, storage and other factors may involveother or additional safety or performance considerations. The user is responsible for determining the suitability of any material for a specific purpose and for adopting such safety precautions as maybe required. Vanderbilt Minerals, LLC does not warrant the results to be obtained in using any material, and disclaims all liability with respect to the use, handling or further processing of any such material.No suggestion for use is intended as, and nothing herein shall be construed as, a recommendation to infringe any existing patent, trademark or copyright or to violate any federal, state or local law orregulation.

PROTOTYPE FORMULAFormula 020398Water Reducible Alkyd Modified Acrylic Latex Direct to Metal PrimerACTIV-8 1 Drier, Stabilizer and AcceleratorPoundsGallonsDISPERSION68.17.8Kelsol 3961-B2G-75225.03.2Barium sulfonate corrosion inhibitorPreblend the next four items and add:26.23.6Arcosolv PnB35.20.7Arcosolv PM Acetate3ACTIV-81 Drier, Stabilizer and Accelerator0.40.1Cobalt Hydrocure e pH and adjust to 8.0 to 8.5 with triethanolamine.50.01.5Ti-Pure R 9005High speed disperse for 15 minutes. Reduce speed for let 180.5015.043.610.650.050.200.5015.046.001.50LET DOWNNeoCryl 6085 Latex6Arcosolv PnBWaterMix at slow speed for 10 .322.92TOTALS895.3100.0106.25100.01PAINT PROPERTIESDensity% Solids by weight% Solids by volume% PVCPigment to binder ratioCalculated VOC9.0 lbs/gal36.530.750.19:11.98 lbs/gal1.06 g/ml238 g/lRAW MATERIAL SUPPLIERSTRADEMARKS1Registered and pending trademarks appearing printed in bold in these materials arethose of Vanderbilt Minerals, LLC. For a complete listing, please visitVanderbilt Minerals, LLC, Norwalk, CT2Reichhold, Inc., Research Triangle Park, NC3Lyondell Chemical Company, Rotterdam, The Netherlands4OM Group, Inc., Cleveland, OH5E.I. DuPont de Nemours & Company, Wilmington, DE6AstraZeneca Pharmaceuticals LP, Wilmington, DEhttp://www.vanderbiltminerals.com/ee content/Documents/Technical/Trademarks VM Web.pdfArcosolv is a registered trademark of Lyondell Chemical Company.Cobalt Hydrocure is a registered trademark of OM Group, Inc.Kelsol is a registered trademark of Reichhold Chemical, Inc.NeoCryl is a registered trademark of DSM NeoResins B.V.Ti-Pure is a registered trademark of E.I. DuPont de Nemours CompanyRev09/10/2013Before using, read, understand and comply with the information and precautions in the Safety Data Sheets, label and other product literature. The information presented herein, while not guaranteed,was prepared by technical personnel and, to the best of our knowledge and belief, is true and accurate as of the date hereof. No warranty, representation or guarantee, express or implied, is maderegarding accuracy, performance, stability, reliability or use. This information is not intended to be all-inclusive, because the manner and conditions of use, handling, storage and other factors may involveother or additional safety or performance considerations. The user is responsible for determining the suitability of any material for a specific purpose and for adopting such safety precautions as maybe required. Vanderbilt Minerals, LLC does not warrant the results to be obtained in using any material, and disclaims all liability with respect to the use, handling or further processing of any such material.No suggestion for use is intended as, and nothing herein shall be construed as, a recommendation to infringe any existing patent, trademark or copyright or to violate any federal, state or local law orregulation.

PROTOTYPE FORMULAFormula 090909High Solids Alkyd Corrosion Inhibitive PrimerVANSIL W-301 Wollastonite,ACTIV-8 1 Drier Stabilizer and .7Beckosol 3859-Z-80 High Solids AlkydResin2Aromatic 1003125.0 NeoCryl 6085 Latex7523.4Arcosolv PnB331.4Water26.7Measure pH and adjust to 8.0 to 8.5 with AMP 956Mix at slow speed for 10 minutesTOTALSPAINT PROPERTIESDensity% Solids by weight% Solids by volume% PVCPigment to binder ratioCalculated VOC885.78.9 lbs/gal35.129.550.19:11.84 062 g/ml221 g/lRAW MATERIAL SUPPLIERSTRADEMARKS1Registered and pending trademarks appearing printed in bold in these materials arethose of Vanderbilt Minerals, LLC. For a complete listing, please visitVanderbilt Minerals, LLC, Norwalk, CT2Reichhold, Inc., Research Triangle Park, NC3Lyondell Chemical Company, Rotterdam, The Netherlands4OM Group, Inc., Cleveland, OH5E.I. DuPont de Nemours & Company, Wilmington, DE6Angus Chemical Company, Buffalo Grove, IL7DSM NeoResins, Wilmington, MAhttp://www.vanderbiltminerals.com/ee content/Documents/Technical/Trademarks VM Web.pdfAMP-95 is a registered trademark of Angus Chemical Company.Arcosolv is a registered trademark of Lyondell Chemical Company.Cobalt Hydrocure is a registered trademark of OM Group, Inc.Kelsol is a registered trademark of Reichhold Chemical, Inc.NeoCryl is a registered trademark of DSM NeoResins B.V.Ti-Pure is a registered trademark of E.I. DuPont de Nemours & Company.Rev09/10/2013Before using, read, understand and comply with the information and precautions in the Safety Data Sheets, label and other product literature. The information presented herein, while not guaranteed,was prepared by technical personnel and, to the best of our knowledge and belief, is true and accurate as of the date hereof. No warranty, representation or guarantee, express or implied, is maderegarding accuracy, performance, stability, reliability or use. This information is not intended to be all-inclusive, because the manner and conditions of use, handling, storage and other factors may involveother or additional safety or performance considerations. The user is responsible for determining the suitability of any material for a specific purpose and for adopting such safety precautions as maybe required. Vanderbilt Minerals, LLC does not warrant the results to be obtained in using any material, and disclaims all liability with respect to the use, handling or further processing of any such material.No suggestion for use is intended as, and nothing herein shall be construed as, a recommendation to infringe any existing patent, trademark or

VANSIL W is an excellent extender pigment for powder coatings as well as solvent-thinned and latex paints. VANSIL W-50 disperses to a to egman fineness at three pounds per gallon. This grade is suitable for liquid industrial and corrosion resistant coatings, powder coatings, and semi-gloss architectural coatings. n powder coatings, this grade

Related Documents:

MDwise Formulary Introduction – Hoosier Healthwise (HHW) HHW members must use MDwise network pharmacies to access their prescription drug benefit. How do I use the formulary? There are two ways to find your drug within the formulary: Medical Condition Drugs in this formulary are grouped into categories depending on the type of medical

Articulate with concept of Drug Formulary Understand the importance of drug formulary Describe how to read d rug formulary Understand the purpose of maintaining drug formulary Describe the concept of Current Index of Medical Specialties (CIMS) Know i mportance and u se of CIMS

Blue Cross Blue Shield of North Dakota Drug Formulary . January 2021 Please consider talking to your doctor about prescribing formulary medications, which may help reduce your out-of-pocket costs. This list may help guide you and your doctor in selecting an appropriate medication for you. The drug formulary is regularly updated.

You must generally use network pharmacies to use your prescription drug beneft. Benefts, formulary, pharmacy network, and/or copayments/coinsurance may change on January 1, 2022, and from time to time during the year. WHAT IS THE MEDICAREBLUE RX FORMULARY? A formulary is a list of covered drugs selected by MedicareBlue Rx in consultation with a

The Formulary Tiers tab of the RX Drug Template (screen shot above) tells us a lot about the Formulary IDs. For example, we can see that Formulary ID WAF002 uses Drug List 1 (purple circle), covered drugs are separated into 7 tiers (blue circle), each tier

Nov 01, 2019 · Anthem Blue MedicareRx Standard (PDP)’s Formulary?” Drugs removed from the market. If the Food and Drug Administration deems a drug on our formulary to be unsafe or the drug’s manufacturer removes the drug from the market, we will immediately remove the drug from our formulary and pr

2016, and from time to time during the year. Page 1 of 98 What is the Aetna Medicare Comprehensive Formulary? A formulary is a list of covered drugs selected by our plan in consultation with a team of . Aetna Formulary The compreh

c. AEMCLRP accreditation for automotive EMC testing 2) The Regulatory requirements of the European Automotive EMC Directive 2008/104/EC, and UN ECE REG 10 (which is used worldwide) 3) Doing EMC to control Functional Safety risks. The design, risk assessment, verification and validation techniques that should be done in addition to the above tests, for ESAs that can affect vehicle safety, to .