Micro Cart - Sun Mountain - Golf Bags, Push Carts, Men .

Micro Cart User's GuideTo take full advantageof the ergonomic features ofyour new Sun MountainMicro Cart, please read thefollowing information .

Umbrella holder mountConsole tray includes apadded valuables tray andmagnetic score card holderAdjustable handleLightweight aluminumframeFour wheel designrequires no trackingadjustmentLow center ofgravity providessuperior stability

Your Micro Cart has several innovative features designed forconvenience, easy access and use.

INSTRUCTIONS FOR UNFOLDING YOUR MICRO CARTSTEP ONE: UNFOLDING THE UPRIGHT TUBESRelease the folding latch underneaththe accessory tray by lifting up on therim of the cup holder. While holdingthe front wheel in place with yourhand or foot, pull the handle backuntil the upright tubes are fullyextended . Secure the cart byengaging the yellow latch hookand lever as shown in theillustration on page 4. If yourlever is too tight, loosen thenut at the base of the latch hook,turn the latch hook until the lever is comfortable to maneuver,and retighten the nut.STEP TWO: SECURING THE HANDLELift the handle, until thehandle height is comfortable.Move the yellow handle latchforward toward the upper bagrest to secure the handle.Over time, the handle tensionmay decrease causing the handleto ratchet. To increase the tension,simply turn the twist knob clockwisein small increments until the handleis secure. It is easiest to makethis adjustment when the cart isfolded.

STEP THREE: ADJUSTING THE HANDLE HEIGHTTo reset the handle height, release the handle by pulling thehandle latch toward the accessory tray. Lift or lower thehandle to the new height and secure the handle latch.STEP FOUR: LOADING YOUR GOLF BAGUnfold the triangular lower bag support and place the bottom ofyour golf bag on it. Then lean the top part of your bag into theupper bag support. The bag bracket secures your bag withoutstraps. The width of the upper bag support can be adjusted byturning the thumb screws on both sides. If your bag pocketsare touching the front wheels, you may expand the front axle.See page 13 for instructions.STEP FIVE: STEERINGTo steer you cart, push down on the handle so the frontwheels lift slightly off the ground. Then pivot right or left tochange direction, lower the front wheels and go.

ACCESSORIES TRAY ASSEMBLYItem #1-23456789101112131415Part escriptionTray AssemblyMagnet Strap with MagnetsMagnet PlateTorsion SpringM4-0.7 Nylock NutM4-0.7x44mm Phillips Pan Head ScrewBeverage Holder KitHinge Post3.6x6mm Phillips Pan Head Screw w/washerM3x5mm Mill Cauda with Pan Head ScrewSpring PlateUpper Tray PadLower Tray Pad6.35X6.35 MagnetQty11111112131114

HANDLE PARTSItem #123-456789101112Part 6SV1-209SV1-210SV1-903B005-122DescriptionUmbrella Holder ReceiverUmbrella Mount KitUmbrella Holder Bungee w/ClaspHandle Tube Assembly (cart/color specific)Handle Grip (color specific)Accessories Tray Assembly4x20mm Phillips Pan Head Screw6.4mm Washer¼”X20mm Phillips Pan Head ScrewUmbrella Clip KitM4x12mm Phillips Pan Head ScrewQty11112141112

Item #1234567891011121314151617181920212223Part 76DescriptionUpper Latch AssemblyTube End Plug8-130.5mm BoltLeft Handle PivotRight Handle PivotM6-8x125.7mm Bolt8x133mm BoltMain FrameUpper Latch Assembly5x15mm RivetM5x12mm ScrewM6-1.0 Nylock NutUpper Latch AssemblyUpper Bag Support BraceBag Wrap Arm (color specific)Bag Wrap Cushion (color specific)Bag Wrap Arm (color specific)Main FrameHandle Latch E-clipM6-1.0x65mm Phillips Pan Head ScrewThumb Screw3mm E-clipStrengthen Piece of Handle PawlQty12111111121511121122221

Item #123456-789101112131415161718Part 215MC1-222DescriptionM6 X35mm Hexagon ScrewM6 Nylock NutLower Bag Support Kit (Old style/no seat slot)Main FrameM4x14mm ScrewSpade Supports (old bag support kit required)M3-0.5x12mm Phillips Pan Head ScrewFront Wheel (color specific)Front Rim6-12mm Flat WasherM6 NutFront Rim Center Cap (color specific)Front AxleFront Axle Bushing4x8 Lock Washer Internal Teeth6-12mm Flat WasherM3-0.5 Nylock Nut1,2,&17 ship together as a setQty221214222224244

Item #123456789101112131415Part 7MC2-346DescriptionMain FittingM5x39mm Phillips Pan Head ScrewM5-0.8 Nylock Nut9mm E-ClipOutrigger Tube (color specific)Upper Delta LinkRight Parallel LinkRight Wheel FittingRear AxleRight Rear Wheel-No Brake (color specific)Left Rear Wheel-w/ Brake (color specific)Rear Rim6-12mm Flat WasherM6 NutRear Center cap (color specific)Pouch ClipQty133221112113222

Item 9Part criptionM6x160mm Bolt6-14mm Flat WasherUpright Tube Pivot PostM5-0.8 Nylock NutUpright LinkM5X74.4mm Phillips Pan Head ScrewM5X39mm Phillips Pan Head ScrewM6 NutM5-8x142.4mm Lower Milled Draw BoltMain FittingUpper Delta LinkUpper Main Frame Fitting (color specific)Lower Latch Assembly (color specific)M5x12.8 Hexagon Head BoltLower Latch Assembly (color specific)M5x44.8mm Phillips Pan Head ScrewM5.28mm Phillips Pan Head ScrewM4x18mm Phillips Pan Head ScrewLower Latch Assembly (color specific)SliderM4-0.7 Nylock Nut4-14mm Flat WasherM4x6mm Phillips Pan Head Screw6-12mm Flat WasherUpright Link Rotating Ring5x15 RivetLower Latch Assembly (color specific)M5x17.5 Hexagon Head BoltQty2229232511111111141242212111

Item #123456789101112131415161718Part SV1-206MC1-323MC1-229MC2-346DescriptionM5-44.8mm Phillips Pan Head ScrewBrake HousingBrake Mounting BaseM4x20 HEX ScrewBrake SpringDisc Brake3x10mm Phillips Pan Head Screw w/washerBrake PinRear AxleLeft Wheel Fitting6-12mm Flat WasherM5-0.8 Nylock NutLower Brake Cable Adjustment StudM6 Nut6x0.8mm E-clipLeft Parallel LinkLower Delta LinkPouch ClipQty211111311122111112

Adjusting the Brake:The brake cable lengthens over time and as a result, thebrake pin hits the disc brake. To tighten the brake cable, turnthe brake cable adjustment stud clockwise (item 7) until thebrake pin has enough clearance.Item #12345678910111213Part 005-419Refer to 8SV1-306MC1-273MC1-274MC1-275DescriptionBrake Lever MountM4-0.7x35mm Phillips Pan Head ScrewM4-0.7 Nylock NutBrake Level with LinkageM6-1.0x22mm Phillips Pan Head ScrewM6-1.0 Nylock NutBrake Cable Adjustment Stud and NutBrake Cable Kit and HardwareBrake Cable SheathingBrake Cable Sheathing Clip3x10mm Phillips Pan Head ST ScrewM4x5mm Phillips Pan Head ScrewBrake Cable StudQty1221111116611

Extendable Front AxlesIf your bag pockets are touching the front wheels, the frontaxle can be extended to accommodate the larger bag. Toextend the front axles, unscrew the four hex screws (A,B,C)using the allen wrench we provided, and pull the wheelsoutward. There are four holes on each axle; choose the widththat works best for your bag and refasten the hex screws.Adjusting the Alignment:All Micro-Carts go through alignment testing before they areshipped. However, if your cart is not rolling straight you canadjust the alignment with the internal hex bolt (B & C). If yourcart goes right turn the left bolt (B) clockwise and the right bolt(C) counter-clockwise. Conversely, if your cart goes left, turnthe left bolt (B) counter-clockwise and the right bolt (C)clockwise.Brake Lock OutIf the brake cable fails,you will need todisengage the brakepin. To do so, flip thecart upside down andpull screw (A) back andinto the locked positionas shown.

Maintenance:Fertilizers and other chemicals used on golf courses can be corrosiveover time. To keep the powder-coated finish of your Speed Cart in goodcondition, wash your cart regularly with a damp wash cloth and milddetergent.Limited Warranty:Sun Mountain warrants the Micro Cart to be free of defects in materialsand workmanship. The cart frame (two parallel tubes from the handle tothe wheel) is warranted for 3 years from date of purchase. Other partssuch as the tires, brakes, handle wrap, etc. are warranted for 1 year fromdate of purchase. This warranty does not cover normal wear and tear,damage, failure or loss resulting from misuse, accident, neglect or failureto follow instructions or warnings in this user’s guide.IMPORTANT!Pulling the Speed Cart V1 behind a power cart or using it as part of arental fleet voids the warranty. Sun Mountain is the sole judge of anyclaim or warranty. Proof of purchase is required.Warranty Registration:Please register your item by visiting our Customer Care section atwww.sunmountain.comClaim Procedure:If you have a claim covered by the warranty, please call our customerservice staff to identify and resolve the problem.If it is deemed necessary to return your cart, a return authorizationnumber will be provided by the customer service agent. This numberMUST be included on the product or package being returned.For claim information, please call 1-800-227-9224.

For customer service or replacement partscall 1-800-227-9224.Visit our web site atwww.sunmountain.comSUN MOUNTAIN301 N. 1st Street W.Missoula, MT 59802

All Micro-Carts go through alignment testing before they are shipped. However, if your cart is not rolling straight you can adjust the alignment with the internal hex bolt (B & C). If your cart goes right turn the left bolt (B) clockwise and the right bolt (C) counter-clockwise. Conversely, if your cart goes left, turn