Husqvarna 16” Chainsaw
Standard Operating procedureHUSQVARNA 16” CHAINSAWVersion 2 Issue date: 02/06/2016Page 1 of 620 Goodshed Road Upper HuttPhone 04 528 4473Husqvarna 16” ChainsawNameRecommended UseCutting Firewood up to 250 mm diameterSection 1: Equipment DetailsManufacturerHusqvarna Construction ProductsSupplied by Youngman Richardson &Co. NZwww.yrco.co.nzEmergency Contact detailsGarry Bull (Upper Hutt Hire) 027 742 6583IMPORTANT: The information contained in this Standard Operating Procedure isintended as a summary only. Users must read the operating manual and familiarizethemselves with the equipment before commencing use.Section 2: Hazards IdentificationA chain saw is a dangerous tool if used carelessly orincorrectly and can cause serious, even fatal injuries.It is very important that you read and understand thecontents of this ESDS and the operator’s manual.This chain saw for forest service is designed for forestwork such as felling, delimbing and cutting. You MUSTonly use the saw with the bar and chain combinationsprovided.The chain brake must be engaged when the chain sawis started to reduce the chance of contact with themoving chain during starting. Never start a chain sawunless the bar, chain and all covers are fitted correctly.Otherwise the clutch can come loose and causepersonal injuries.NEVER “drop start” the chainsaw. Risk of loss ofcontrol. Always start the chainsaw on the ground.Never use the machine if you are fatigued, while underthe influence of alcohol or drugs, medication oranything that could affect your vision, alertness,coordination or judgement. Operation of theequipment must not be performed by persons underthe influence of alcohol, drugs, medications or anychemical substances capable of impairing the abilitiesof that person.Fuel is highly flammable, especially on hot surfaces.HANDLE WITH CARE!Never refuel while the Engine is running.
Standard Operating procedureHUSQVARNA 16” CHAINSAWVersion 2 Issue date: 02/06/2016Page 2 of 620 Goodshed Road Upper HuttPhone 04 528 4473Exhaust gases are poisonous. DO NOT run the engineindoors or within a confined space. Always ensurethere is adequate ventilationNot to be operated by a person under the age of 16 years.Never leave the engine running when unattended. Shut themachine down even if unattended for a short period.Do not operate the machine unless all people are clear ofthe cutting hazard zone. Never reach or bend over thechainsaw while it is running.Section 3: Additional InformationCertification: Does this item requirespecial licensing or certification?Additional links? Worksafe NZ etcNoWSNZ “Safety with Chainsaws”Section 4: Fuel and LubricantsFuel / OilSection 5: Log BookDoes this equipment require a dailycheck and entry in the log book?Use 91 unleaded petrol and 2-stroke oil mixed50:1Use approved Chain lubricantNo, not applicable.Section 6: Personal Protective Equipment (PPE)Appropriate personal protective equipment (PPE) is required for the operator andpersons assisting with loading and unloading.In addition wear suitbable protective clothing to provide protection to the leg and groinarea. Husqvarna recommend leather leggings or Chaps, and garters.
Standard Operating procedureHUSQVARNA 16” CHAINSAWVersion 2 Issue date: 02/06/2016Page 3 of 620 Goodshed Road Upper HuttPhone 04 528 4473Section 7: Emergency precautionsDo you have aDo you have aFIRST AID KIT?FIRE EXTINGUISHER?Can you make anEMERGENCY CALL?Section 8: Operating Conditions / General Safety Precautions
Standard Operating procedureHUSQVARNA 16” CHAINSAWVersion 2 Issue date: 02/06/2016Page 4 of 620 Goodshed Road Upper HuttPhone 04 528 4473
Standard Operating procedureHUSQVARNA 16” CHAINSAWVersion 2 Issue date: 02/06/2016Page 5 of 620 Goodshed Road Upper HuttPhone 04 528 4473Section 9: Engine operationThe chain brake must be engaged when the chain saw is started. Activate the brake by movingthe front hand guard forwards.9.1 Cold Starting Set the choke control in the choke position by pull the choke control outwards. Thisautomatically sets the stop switch to the start position. Press the Decompression valve to reduce the pressure in the cylinder and makestarting easier. You should always use the decompression valve when starting themachine. Once the machine has started the valve will automatically return to itsoriginal setting. Pull the starter handle with your right hand and pull out the starter cord slowly untilyou feel a resistance (as the starter pawls engage) then pull firmly and rapidly untilthe engine fires. Push in the choke control as soon as the engine fires which can beheard through a "puff" sound. Keep on pulling the cord powerfully until the enginestarts.9.2 Warm Starting The correct choke/start throttle setting for warm starting is obtained by moving thechoke control to the choke position and then pushing it in again. Press the air purge repeatedly (at least 6 times) until fuel begins to fill the bulb. Thebulb need not be completely filled. Press the Decompression valve to reduce the pressure in the cylinder and makestarting easier. You should always use the decompression valve when starting themachine. Once the machine has started the valve will automatically return to itsoriginal setting. Pull the starter handle with your right hand and pull out the starter cord slowly untilyou feel a resistance (as the starter pawls engage) then pull firmly and rapidly untilthe engine fires. As the chain brake is still engaged the speed of the engine must be set to idling assoon as possible, this is achieved by disengaging the throttle lock. Disengagementis done by gently touching on the throttle trigger. This prevents unnecessary wear tothe clutch, clutch drum and brake band. Allow the machine to idle a few secondsbefore giving full throttle. CAUTION! Do not pull the starter cord all the way out anddo not let go of the starter handle when the cord is fully extended. This can damagethe chainsaw. Always hold the saw with both hands. The right hand MUST be on the rear handle,and the left hand MUST be on the front handle. All people, whether right or lefthanded, MUST use this grip. Use a firm grip with thumbs and fingers encircling thechain saw handles.9.3 Stopping Stop the engine by switching off the ignition
Standard Operating procedureHUSQVARNA 16” CHAINSAWVersion 2 Issue date: 02/06/2016Page 6 of 620 Goodshed Road Upper HuttPhone 04 528 4473Section 10: Additional InformationAlways use common sense! It is not possible to cover every conceivable situation youcan face when using our equipment.Always exercise care and use your common sense. Avoid all situations which youconsider to be beyond your capability. If you still feel uncertain about operatingprocedures after reading these instructions and the owner’s manual, you should consultan expert before continuing.The information contained herein is true and accurate to the best of our knowledge. Nowarranty or guarantee is expressed or implied regarding the accuracy of information orinstructions. Users MUST consult the manufacturer’s manual or handbook. While everyeffort has been made to summarise the important Health and Safety information for thesafe use of this equipment, Upper Hutt Hire Ltd shall not be liable in any way for anyreliance by any person or entity on the accuracy of information or data contained in thisdocument or its attachments.This SOP based on information contained in the Husqvarna 455e Rancher 455 Rancher 460 Rancher operators manualreference 1153137-26 dated 2010-05-07Revision dateJune 2021
Name Husqvarna 16” Chainsaw Recommended Use Cutting Firewood up to 250 mm diameter Section 1: Equipment Details . This SOP based on information contained in the Husqvarna 455e Rancher 455 Rancher 460 Rancher operators manual reference 1153137
Your Remington Cordless Polesaw and Cordless Chainsaw may have been purchased together (as a 2-in-1 polesaw/chainsaw) or seperate (chainsaw only). If the chainsaw was purchased separately, the pole is available as an accessory and may be purchased by visiting the "On-Line Outlet" at www.remingtonpowertools.com.
Husqvarna 235 Husqvarna H701 HOP 1/2 Yes “H701” stamped into the front of muffler Husqvarna 235e Husqvarna . Husqvarna 445 e-series Trio Brake 544 14 77-0
the chainsaw, make sure the saw chain is not contacting anything. A moment of inattention while operating chainsaws may cause entanglement of your clothing or body with the saw chain. v Always hold the chainsaw with your right hand on the rear handle and your left hand on the front handle. Holding the chainsaw with a reversed hand
have tons of used partner chainsaw parts. we have also bought out 3 partner dealerships in the last year and have lots of nos partner c maxtra chainsaw parts store maxtra gas pole saw, 42.7cc 2-cycle 8.2ft to 11.4 ft extendable cordless gas chainsaw,powerful long reach tree tr
Carry the chainsaw by the front handle with the chainsaw switched off and away from your body. When transporting or storing the chainsaw always fit the guide bar cover. Proper handling of the chainsaw will reduce the likelihood of accidental contact with the moving saw chain. Follow instructions for lubricating, chain tensioning and
Thank you for buying a Ryobi chainsaw. Your chainsaw has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance. Some regions have regulations that restrict the use of the product to some operations.
report on chainsaw milling.Developing alternative to illegal chainsaw milling through multistakeholder dialogue in Ghana and Guyana project. FORIG RESEARCH REPORT NO . CSIR-Forestry Research Institute of Ghana/Tropenbos International, Netherlands Published by For
(Corporate Officer). Full day event, get a hamper and 10 via expenses for drinks. Andrew Tamplin is doing a morning session, breakout rooms including a live band, quiz, virtual Christmas choir, guided meditation/yoga, virtual pub, pets corner, creative room (cooking workshops, magic tricks, circus skills). Dec 11th.
