Operator's Manual 40v Max* Lithium Chain Saw
Operator'sManual40v Max* Lithium ChainModel-Saw98023z CAUTION: Read, understand and followall Safety Rules and Operating Instructionsin this manual before using this product.Sears Brands Management Corporation,Hoffrnan Estates, IL 60179 U.S.A.See the full line of Craftsman productsat craftsman.corn SAFETYOPERATIONMAINTENANCETROUBLESHOOTINGESPA !OL PG. 18*Maximum initial battery packvoltage (measured without aworkload) is 40 volts. The nominalvoltage is 36.*El m&ximo voltaje inicial delpaquete de baterias (medido sinuna carga de trabajo) es 40 voltios.Si se mide con una carga detrabajo, el voltaje nominal es 36.Part No. 90616763September 2014
CRAFTSMANLiMiTEDWARRANTYFOB FOUR YEARS from the date of sale, this product is warranted against defectsin material or workmanship.FOB TWO YEARS from the sale date, a supplied battery pack or charger iswarranted against material or workmanship defects.WITH PROOF OF SALE, a defective product will be replaced free of charge.For warranty coverage details to obtain free replacement,visit the web page:www.craftsman.com/warrantyThis warranty does not cover the cutting chain, which is an expendablecan wear out from normal use within the warranty period.part thatThis warranty is void if this product is ever used while providing commercialservices or if rented to another person.This warranty gives you specificwhich vary from state to state.legal rights, and you may also have other rightsSears Brands Management Corporation,SYMBOLSIGNAL/ SAFETYHoffman Estates, tL 60179MEANINGALERTSYMBOL:Indicates DANGER,May be used in conjunction with other symbols or pictographs.Z DANGER:WARNING,OR CAUTION.Indicates hazardous situation which, if not avoided, will result in death or serious injury./ WARNING:serious injury.Indicates hazardous situation which, if not avoided, could result in death orZ CAUTION:Indicates a hazardous situation which, if not avoided, could result in minor ormoderate injury or property damage.GeneralPower Tool Safety Warningsz WARNING: Read all safety warnings and all instructions.Failure tofollqw th.e.warnings and instructions may result in electric shock, fire and/orserious n]ury.z WARNING:Some dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to the State of California to cause cancer,birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically-treated lumber.Your risk from these exposures varies, depending on how often you do this type of work. To reduceyour exposure to these chemicals: work in a well ventilated area, and work with approved safetyequipment, such as those dust masks that are specially designed to filter out microscopic particles. Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and otherconstruction activities. Wear protective clothing and wash exposed areas with soap andwater. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption ofharmful chemicals.SAVE ALL WARNINGSAND INSTRUCTIONSFOR FUTURE REFERENCEThe term "power tool" in the warnings refers to your mains-operated (corded)power tool or battery-operated(cordless) power tooL
SAVE THESE iNSTRUCTiONS1) WORK AREA SAFETYa) Keep work area clean and well lit. Cluttered or dark areas invite accidents.b) Do net operate power tools in explosive atmospheres,such as in the presenceof flammableliquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.c) Keep children and bystandersaway while operating a power tool. Distractionscan causeyou to lose control2) ELECTRICALSAFETYa) Power tool plugs mustmatchthe outlet.Neverany adapter plugs with earthed (grounded)outlets will reduce risk of electric shock.b) Avoid body contact with earthedor groundedmodifythe plug in any way. Do not usepower tools.Unmodifiedplugs and matchingsurfaces such as pipes, radiators,ranges andrefrigerators.There is an increased risk of electric shock if your body is earthed or grounded.c) Do not expose power tools to rain or wet conditions.Water entering a power tool willincrease the risk of electric shock.d) Do not abusethe cord.Neveruse the cordfor carrying,tool. Keep cord away from heat, oil, sharp edgescords increase the risk of electric shock.pullingor movingor unpluggingparts. Damagede) When operating a power tool outdoors, use an extension cord suitableUse of a cord suitable for outdoor use reduces the risk of electric shock.f) if operatinginterruptera power tool in a damp location is unavoidable,(GFCI) protected supply.Use of a GFCI reducesthe poweror entangledfor outdooruse.use a ground fault circuitthe risk of electric shock.3) PERSONALSAFETYa) Stay alert, watch what you are doing and use common sense when operating a power tool. Donot use a power tool while you are tired or under the influence of drugs, alcohol or medication.A moment of inattention while operating power tools may result in serious personal injury.b) Use personal protective equipment.Always wear eye protection.Protective equipmentsuch as dust mask, nonskid safety shoes, hard hat, or hearing protectionconditions will reduce personal injuries.c) Prevent unintentionalstarting.Ensure the switch is in the off positionused for appropriatebeforeconnectingtopower source and/orbattery pack, picking up or carryingthe tool. Carrying power tools withyour finger on the switch or energizing power tools that have the switch on invites accidents.d) Remove any adjustingkey or wrench before turningthe power tool on. A wrench or a keyleft attached to a rotating part of the power tool may result in personal injury.e) Do not overreach.Keep proper footingand balance at all times. This enables better controlof the power toot in unexpectedsituations.f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves awayfrom moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.g) If devices are provided for the connection of dust extraction and collection facilities, ensure theseare connected and properly used. Use of dust collection can reduce dust-related hazards.4) POWER TOOL USE AND CAREa) Do not force the power tool. Use the correctpowertool for your application.The correctpower toot will do the job better and safer at the rate for which it was designed.b) Do not use the power tool if the switch does not turn it on and off. Any power toot thatcannot be controlled with the switch is dangerous and must be repaired.c) Disconnectthe plug from the power source and/or the battery pack from the power toolbefore making any adjustments,changingaccessories,or storing power tools. Suchpreventive safety measures reduce the risk of starting the power toot accidentally.d) Store idle power tools out of the reach of children and do not allow persons unfamiliarwith the power tool or these instructionsto operate the power tool. Power tools aredangerous in the hands of untrained users.e) Maintain power tools. Check for misalignmentor bindingof movingparts, breakage of parts and
ion.If damaged, have the power toolrepaired before use. Many accidents are caused by poorly maintained power tools.f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cuttingedges are less likely to bind and are easier to controlg) Use the power tool, accessoriesand tool bits, etc. in accordancewith these instructions,taking into account the working conditionsand the work to be performed.Use of the power toolfor operations different from those intended could result in a hazardous situation.5) BATTERY TOOL USE AND CAREa) Recharge only with the charger specified by the manufacturer.A charger that is suitable forone type of battery pack may create a risk of fire when used with another battery pack.b) Use power tools only with specificallydesignatedbattery packs. Use of any other batterypacks may create a risk of injury and fire.c) When battery pack is not in use, keep it away from other metal objects like paper clips,coins, keys, nails, screws, or other small metal objects that can make a connectionfromone terminalto another.Shorting the battery terminals together may cause burns or a fire.d) Under abusive conditions,liquid may be ejected from the battery, avoid contact,ifcontact accidentallyoccurs, flush with water, if liquid contactseyes, additionaUyseekmedical help. Liquid ejected from the battery may cause irritation or burns.6) SERVICEa) Have your power tool serviced by a qualified repair person using only identicalreplacement parts. This will ensure that the safety of the power toot is maintained.CHAINSAW SAFETYWARNINGS: Keep all parts of the body away from the saw chain when the chain saw is operating. Beforeyou start the chain saw, make sure the saw chain is not contacting anything. A moment ofinattention while operating chain saws may cause entanglement of your clothing or body with thesaw chain. Always hold the chain saw with your right hand on the rear handle and your left hand onthe front handle. Holding the chain saw with a reversed hand configuration increases the risk ofpersonal injury and should never be done. Hold the power tool by insulated gripping surfaces only, because the saw chain maycontact hidden wiring. Saw chains contacting a "live" wire may make exposed metal parts of thepower toot "live" and could give the operator an electric shock. Wear safety glasses and hearing protection. Further protective equipment for head, hands,legs and feet is recommended. Adequate protective clothing will reduce personal injury by flyingdebris or accidental contact with the saw chain. Do not operate a chain saw in a tree. Operation of a chain saw while up in a tree may result inpersonal injury. Always keep proper footing and operate the chain saw only when standing on fixed, secureand level surface. Slippery or unstable surfaces such as ladders may cause a loss of balance orcontrol of the chain saw. When cutting a limb that is under tension be alert for spring back. When the tension in thewood fibers is released the spring loaded limb may strike the operator and/or throw the chain sawout of control Use extreme caution when cutting brush and saplings. The slender material may catch thesaw chain and be whipped toward you or puff you off balance. Carry the chain saw by the front handle with the chain saw switched off and away from your body.When transporting or storing the chain saw always fit the scabbard. Proper handling of the chainsaw will reduce the likelihood of accidental contact with the moving saw chain. Follow instructions for lubricating, chain tensioning and changing accessories. Improperlytensioned or lubricated chain may either break or increase the chance for kickback. Keep handles dry, clean, and free from oil and grease. Greasy, oily handles are slipperycausing loss of control Cut wood only. Do not use chain saw for purposes not intended. For example: do not use
chainsawforcuttingplastic,masonry or non-wood building materials.for operations different than intended could result in a hazardous situation.Use of the chain sawCAUSESAND OPERATORPREVENTIONOF KICKBACK:Kickback may occur when the nose or tip of the guide bar touches an object, or when the woodcloses in and pinches the saw chain in the cut.Tip contact in some cases may cause a sudden reverse reaction, kicking the guide bar up and backtowards the operator.Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towardsthe operator.Either of these reactions may cause you to lose control of the saw which could result in seriouspersonal injury. Do not rely exclusively upon the safety devices built into your saw. As a chain sawuser, you should take several steps to keep your cutting jobs free from accident or injury.Kickback is the result of tool misuse and/or incorrect operating procedures or conditions and can beavoided by taking proper precautions as given below: Maintain a firm grip, with thumbs and fingers encircling the chain saw handles, with bothhands on the saw and position your body and arm to allow you to resist kickback forces.Kickback forces can be controlled by the operator, ff proper precautions are taken. Do not let go ofthe chain saw. Do not overreach and do not cut above chest height. This helps prevent unintended tip contactand enables better control of the chain saw in unexpected situations. Only use replacement bars and chains specified by the manufacturer. Incorrect replacementbars and chains may cause chain breakage and/or kickback. Follow the manufacturer's sharpening and maintenance instructions for the saw chain.Decreasing the depth gauge height can lead to increased kickback.THE FOLLOWINGPRECAUTIONSSHOULDBE FOLLOWEDTO MiNiMiZE KICKBACK:(1.) Grip Saw Firmly. Hold the chain saw firmly with both hands when the motor is running. Use afirm grip with thumbs and fingers encircling the chain saw handles. Chain saw will pull forward whencutting on the bottom edge of the bar, and push backward when cutting along the top edge of the bar.(2.) Do not over reach.(3.) Keep proper footing and balance at all times.(4.) Don't let the nose of the guide bar contact a log, branch, ground or other obstruction.(5.) Don't cut above shoulder height.(6.) Use devices such as low kickback chain and reduced kickback guide bars that reduce the risksassociated with kickback.(7.) Only use replacement bars and chains specified by the manufacturer or the equivalent.(8.) Never let the moving chain contact any object at the tip of the guide bar.(9.) Keep the working area free from obstructions such as other trees, branches, rocks, fences,stumps, etc. Eliminate or avoid any obstruction that your saw chain could hit while you are cuttingthrough a particular log or branch.(10.) Keep your saw chain sharp and properly tensioned. A loose or dull chain can increase thechance of kickback. Check tension at regular intervals with the motor stopped and tool unplugged,never with the motor running.(11.) Begin and continue cutting only with the chain moving at full speed. If the chain is moving at aslower speed, there is a greater chance for kickback to occur.(12.) Cut one log at a time.(13.) Use extreme caution when re-entering a previous cut. Engage ribbed bumpers into wood andallow chain to reach full speed before proceeding with cut.(14.) Do not attempt plunge cuts or bore cuts.(15.) Watch for shifting logs or other forces that could close a cut and pinch or fall into chain.KICKBACKSAFETYFEATURESzLWARNING: The following features are included on your saw to help reduce the hazard ofkickback; however such features will not totally eliminate this dangerous reaction. As a chain saw user
nseriousinjury. ip.Areduced- ctricchainsaws. ograduallyrideintothecutter.Alow-kickbackchainisa NSIB175.1-2012. Donotoperatechainsawwhilein a tree, on a ladder, on a scaffold, or from any unstablesurface. Hold tool by insulated gripping surfaces when performing an operation where the cuttingtool may contact hidden wiring. Contact with a "live" wire will make exposed metal parts of thetool "live" and shock the operator. Do not attempt operations beyond your capacity or experience. Read thoroughly andunderstand completely all instructions in this manual. Before you start chain saw, make sure saw chain is not contacting any object. Do not operate a chain saw with one hand! Serious injury to the operator, helpers, orbystanders may result from one handed operation. A chain saw is intended for two-handed useonly. Keep the handles dry, clean, and free of oil or grease. Do not allow dirt, debris, or sawdust to build up on the motor or outside air vents. Stop the chain saw before setting it down. Do not cut vines and/or small under brush. Use extreme caution when cutting small size brush and saplings because slender materialmay catch the saw chain and be whipped toward you or pull you off balance.zLWARNING: Use of this tool can generate and/or disburse dust, which may causeserious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratoryprotection appropriate for the dust exposure. Direct particles away from face and body.CHAIN SAW NAMES AND TERMS Bucking - The process of cross cutting a felled tree or log into lengths.Motor Brake - A device used to stop the saw chain when the trigger is released.Chain Saw Powerhead - A chain saw without the saw chain and guide bar.Drive Sprocket or Sprocket - The toothed part that drives the saw chain.Felling - The process of cutting down a tree.Felling Back Cut - The final cut in a tree felling operation made on the opposite side of the treefrom the notching cut.Front Handle - The support handle located at or toward the front of the chain saw.Front Hand Guard - A structural barrier between the front handle of a chain saw and the guide bar,typically located close to the hand position on the front handle.Guide Bar - A solid railed structure that supports and guides the saw chain.Guide Bar Scabbard - Enclosure fitted over guide bar to prevent tooth contact when saw is not in use.Kickback - The backward or upward motion, or both of the guide bar occurring when the saw chainnear the nose of the top area of the guide bar contacts any object such as a log or branch, or whenthe wood closes in and pinches the saw chain in the cut.Kickback, Pinch - The rapid pushback of the saw which can occur when the wood closes in andpinches the moving saw chain in the cut along the top of the guide bar.Kickback, Rotational - The rapid upward and backward motion of the saw which can occur whenthe moving saw chain near the upper portion of the tip of the guide bar contacts an object, such asa log or branch.Limbing - Removing the branches from a fallen treeLow-Kickback Chain - A chain that complies with the kickbackperformance requirements of ANSI B175.1-2012 (when tested ona representative sample of chain saws.)
NormalCuttingPosition- ingcuts. e'sfall. rofthesaw. Reduced Kickback Guide Bar - A guide bar which has been demonstratedto reduce kickback significantly. Replacement Saw Chain - A chain that complies with kickback performance requirements of ANSIB175.1-2000 when tested with specific chain saws. It may not meet the ANSI performancerequirements when used with other saws. Saw Chain - A loop of chain having cutting teeth, that cut the wood,and that is driven by the motorand is supported by the guide bar. Ribbed Bumper - The ribs used when felling or bucking to pivot the saw and maintain positionwhile sawing. Switch - A device that when operated will complete or interrupt an electrical power circuit to themotor of the chain saw. Switch Linkage - The mechanism that transmits motion from a trigger to the switch. Switch Lockout - A movable stop that prevents the unintentional operation of the switch untilmanually actuated.iNTENDED USEYour Craftsman Chain Saw is ideal for pruning applications and cutting small logs up to 12inches (305 mm)in diameter. This tool is intended for consumer use only.SAVE THESEINSTRUCTIONSSYMBOLSThe label on your tool may include the following symbols. The symbols and their definitions are as follows:V.Hz .min .- - or DC.( ) .voltshertzminutesdirect currentClass I Construction[] .(grounded)Class II Construction(double insulated)m/s . meters per secondmm . millimeters.O .Use proper respiratory protectionUse proper hearing protectionPARTS AND FEATURES1. Trigger switch2. Lock-off button3. Front hand guard4. Guide bar5. Saw chain6. Sprocket cover7. Bar adjust locking knob8. Chain tensioning knob9. Guide bar scabbard10. Rear handle11. Front handle12.40V Battery (not shown)13. Oil cap14. Oil level indicatorA . amperesW . watts" -,or AC . alternating currentno . no load speed0 . earthing terminalz . safety alert symbol./min or rpm.revotutionsorreciprocationper minutein . inches. Read instruction manual before useG .Use proper eye protection
iMPORTANTSAFETYiNSTRUCTiONSFOR BATTERYCHARGERSSAVE THESE INSTRUCTIONS: THiS MANUAL CONTAINS IMPORTANT SAFETYINSTRUCTIONS FOR BATTERY CHARGERS, Before using charger, read all instructions and cautionary markings on charger, battery pack, andproduct using battery pack.z WARN NG:SHOCK HAZARD. Do not allow any liquid to get inside charger.z OAUT ON:BURN HAZARD. To reduce the risk of injury, charge only designated Craftsman 'batteries. Other types of batteries may burst causing personal injury and damage.z OAUT ON:Under certain conditions, with the charger plugged in to the power supply, thecharger can be shorted by foreign material. Foreign materials of a conductive nature such as, but notlimited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away fromcharger cavities. Always unplug the charger from the power supply when there is no battery pack inthe cavity. Unplug charger before attempting to clean.z WARNING: THE CHARGER SUPPLIED WITH THIS PRODUCT tS INTENDED TO BEPLUGGED IN SUCH THAT tT tS CORRECTLY ORIENTATED tN A VERTICAL OR FLOORMOUNT POSITION, DO NOT attempt to charge the battery pack with any chargers other than the ones in thismanual. The charger and battery pack are specifically designed to work together. These chargers are not intended for any uses other than charging designated Craftsman rechargeable batteries. Any other uses may result in risk of fire, electric shock or electrocution. Do not expose charger to rain or snow. Pull by plug rather than cord when disconnecting charger. This will reduce risk of damage toelectric plug and cord. Make sure that cord is located so that it will not be stepped on, tripped over, or otherwisesubjected to damage or stress. Do not use an extension cord unless it is absolutely necessary. Use of improper extension cordcould result in risk of fire, electric shock, or electrocution. An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety.The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge hasmore capacity than 18gauge. When using more than one extension to make up the total length, besure each individual extension contains at least the minimum wire size.Minimum Gauge for Cord SetsTotal Length of Cord in Feet0-2526-5051-100101-150(0-7,6m) (7,6-15,2m) 00(0-15,2m) (15,2-30,4m)(30,4-60,9m)(60,9-91,4m)Ampere RatingMore Not moreAmerican Wire GaugeThan Than0 6181616146 101816141210 121616141212 161412Not RecommendedVolts120V Do not place any object on top of charger or place the charger on a soft surface that mightblock the ventilationslots and result in excessiveinternal heat. Place the charger in aposition away from any heat source.The charger is ventilated through slots in the top and thebottom of the housing. Do not mount charger on wall or permanently affix charger to any surface.The charger isintended to use on a flat, stable surface (i.e., table top, bench top). Do not operate charger with damagedcord or plug have them replaced immediately. Do not operate charger if it has received a sharp blow, been dropped,or otherwisedamagedin any way. Take it to an authorized eervice center. Do not disassemblecharger;take it to an authorized service center when service or repair isrequired. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.8
Disconnect the charger from the outlet before attempting any cleaning, This will reduce the riskof electric shock. Removing the battery pack will not reduce this risk. NEVER attempt to connect 2 chargers together, The charger is designed to operate on standard household electrical power (120 Volts). Donot attempt to use it on any other voltage.iMPORTANTz WARNING:SAFETYiNSTRUCTiONSFor safe operation,read this manualFOR BATTERYand manualsoriginallyPACKSsuppfiedwith tootbefore using the charger.The battery pack is not fully charged out of the carton. Before using the battery pack and charger,read the safety instructionsbelow. Then follow charging procedures outlined.READ ALL INSTRUCTIONS Do not incinerate the battery pack even if it is severelydamaged or is completelyworn out.The battery pack can explode in a fire. Toxic fumes and materials are created when battery packsare burned. Do not charge or use battery in explosiveatmospheres, such as in the presence of flammableliquids, gases or dust. Inserting or removing the battery from the charger may ignite the dust or fumes. tf battery contentscome into contact with the skin, immediatelywash area with mild soapand water, ff battery liquid gets into the eye, rinse water over the open eye for 15 minutes oruntil irritation ceases. If medical attention is needed, the battery electrolyte for Li-ion batteries iscomposed of a mixture of liquid organic carbonates and lithium salts. Contentsof opened battery cells may cause respiratoryirritation. Provide fresh air. If symptomspersist, seek medical attention.z WARNING:BURNHAZARD.BATTERYSPARK OR FLAME. Charge the battery packs only in CraftsmanLIQUIDMA Y BE FLAMMABLEIF EXPOSEDTO' chargers. DO NOT splash or immerse in water or other liquids.This may cause premature cell failure. Do not store or use the tool and battery pack in locationswhere the temperaturemay reachor exceed 105 F (40 C) (such as outside sheds or metal buildingsin summer).z' WARNING:Never attemptto open the battery pack for any reason.If battery pack case iscracked or damaged, do not insert into charger. Do not crush, drop or damage battery pack. Do notuse a battery pack or charger that has received a sharp blow, been dropped, run over or damaged inany way (i.e., pierced with a nail, hit with a hammer, stepped on). Damaged battery packs should bereturned to service center for recycling.z WARNING:Fire hazard.Do not storeor carrybatteryso thatmetalobjectscan contactexposedbattery terminals.For example, do not place battery in aprons, pockets, tool boxes,product kit boxes, drawers, etc., with loose nails, screws, keys, etc. Transportingbatteriescanpossiblycause fires if the battery terminalsinadvertentlycome in contact with conductivematerialssuch as keys, coins, hand tools and the like. The US Department of TransportationHazardous Material Regulations(HMR) actuallyairplanes (i.e., packed in suitcases and carry-onprohibit transporting batteries in commerce or onluggage) UNLESS they are properly protected fromshort circuits. So when transportingindividual batteries, make sure that the battery terminals areprotected and weft insulated from materials that could contact them and cause a short circuit.NOTE: M-ION batteriesshould not be put in checked baggage.STORAGERECOMMENDATIONS1. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold.2. Long-term storage will not harm the battery pack or charger, unless the battery is depleted.CHARGINGPROCEDURECraftsman cechargers are designed to charge Craftsman 'battery packs.1. Plug the charger into an appropriate outlet before inserting the battery pack.2. Insert the battery pack into the charger.
gedandmaybeusedatthistimeorleftonthecharger.Recha e discharged batteries as soon as possible after use or battery life may be greatly diminished.LEAVING THE BATTERY IN THE CHARGERThe charger and battery pack can be left connected with the green LED glowing indefinitely. Thecharger will keep the battery pack fresh and fully charged.iMPORTANTCHARGINGNOTES1. Longest life and best performance can be obtained if the battery pack is charged when the airtemperature is between 60 F and 80 F (16 . 27 C). DO NOT charge the battery pack in an airtemperature below 40 F ( 4.5 C), or above 105 F ( 40.5 C). This is important and will preventserious damage to the battery pack.2. The charger and battery pack may become warm to touch while charging. This is a normalcondition, and does not indicate a problem. To facilitate the cooling of the battery pack after use,avoid placing the charger or battery pack in a warm environment such as in a metal shed, or anuninsulated trailer.3. If the battery pack does not charge properly:a. Check current at receptacle by plugging in a lamp or other applianceb. Check to see if receptacle is connected to a light switch which turns power off when you turnout the lights.c. Move charger and battery pack to a location where the surrounding air temperature isapproximately 60 F and 80 F (16 . 27 C).d. If charging problems persist, take the tool, battery pack and charger to your local service center.4. The battery pack should be recharged when it fails to produce sufficient power on jobs which wereeasily done previously. DO
saw chain and be whipped toward you or puff you off balance. Carry the chain saw by the front handle with the chain saw switched off and away from your body. When transporting or storing the chain saw always fit the scabbard. Proper handling of the chain saw will reduce the likelihood ofaccidental contact with the moving saw chain.
C 20μF L 200 mH Capacitor initially charged to 40V, no current initially ÎCalculate ω, f and T ω 500 rad/s f ω/2π 79.6 Hz T 1/f 0.0126 sec ÎCalculate q max and i max q max CV 800 μC 8 10-4 C i max ωq max 500 8 10-4 0.4 A ÎCalculate maximum energies U C q2 max/2C 0.016J U L Li 2 max/2 0.016J
NORTHGATE COLOR PALETTE 2 See page 5 for specifications and warranty details. 3 Max Def Burnt Sienna Max Def Moire Black Max Def Driftwood Max Def Pewter Max Def Georgetown Gray Max Def Resawn Shake Max Def Granite Gray Max Def Weathered Wood Max Def Heather Blend Silver Birch CRRC Product ID 0668-0072 Max Def Hunter Green NORTHGATE
Max. acceleration Z m/s2 5.0 Repeat accuracy/axis /- mm 0.1 LP 100 HS Max. payload kg 220 Max. carrier length X m 120 Max. stroke Z mm 2,300 Max. traverse speed X m/min 300 Max. acceleration X m/s2 4.5 Max. traverse speed Z m/min 120 Max. acceleration Z m/s2 5.0 Repeat accuracy/axis /- mm 0.1 LP 100 HD Max. payload kg 280 Max. carrier length .
Autmatic coil winding unit with complete protective fencing RINGROL 300 T E RINGROL 400 B E RINGROL 560 B E Coil diameter max. 300 mm max. 400 mm max. 560 mm Coil width max. 100 mm max. 200 mm max. 200 mm Coil weight max. 10 kg max. 15 kg max. 25 kg Core diameter 100 / 120 / 150 collapsible (other sizes upon request) 120 - 250 mm
0 2 4 6 8 10 12 Figure 5 ESD Response to IEC 61000-4-2 ( 8kV Contact Discharge) 40V/div 20ns/div Figure 6 ESD Response to IEC 61000-4-2 (-8kV Contact Discharge) 20ns/div 40V/div TLP VOLTAGE (V) Figure 7 Transmission Line Pulsing (TLP) Current vs. Voltage T L P C U R R E N T 12 (A) 0 2 4 6
Transistor manual . r I I I I I I I I I I I 1 I I I . 1 1 1 I I I I I I I I I I I I I TRANSISTOR SPECIFICATIONS . This manual contains three principal sections designed to provide a maximum of infor- . 2634 RCA 1 TO 22 40 25 .100A .150W 751 .400G 50UA 40V 75 26340 ETC 21 TO 5 40 258 .1008 .150W 751 .60013 100UA 40V 66 .0018 .
MAX 6000' MAX 4000' MAX 2500' MAX 3500' MAX 2500' Sector Menorca MAX 1000' Sector 35W MAX 3500' Sector 25W MAX 2500' Sector Ibiza Palma 1000' SFC B A R C E L O N A L E C B F I R A L G I E R S D A A A F I R . RBOTTLANG AIRFIELD MANUAL 02 NOV 07 2 7 9 1 0 8 2 7 9 1 0 8 (FIS) 2 7 9 0 1 8 West
Max Def Burnt Sienna Silver Birch Max Def Resawn Shake Max Def Georgetown Gray Mountain Timber Max Def Moire Black Max Def Weathered Wood Max Def Heather Blend color palette max def colors - Look deeper. With Max Def, a new dimension is added to shingles with a richer mixture of surface granules. You get a brighter, more vibrant, more dramatic .
