3100019-Trans-Flo Rev 10-05-2005
Operation ManualTrans-Flo
The TRANS-FLO SYSTEM is a standard-output ballast that canbe dimmed on most common theatrical SCR dimming systems.The modular design of the TRANS-FLO SYSTEM streamlinesset lighting installations, and its smooth dimming capabilityensures controlled lighting effects.The TRANS-FLO Ballast can operate 15-inch, 2ft, 3ft and 4ftlamps in pairs; two different sized lamps can be powered fromthe same ballast. (Two lamps must be connected for the ballastto operate.)The POWER/DIM Cable provides primary voltage and dimmingcontrol to the first TRANS-FLO Ballast. The Single LockingLamp Harnesses attach directly to each ballast, or they attach toa ballast via a Head Extension ( up to 25ft long ).Jumper Cables link TRANS-FLO Ballasts together ( up to 10 ina series ).The TRANS-FLO SYSTEM operates in three modes:1.INDIVIDUAL BALLAST DIMMING MODE ( twolamps )2.SERIES BALLAST DIMMING MODE (up to 10ballasts per series )3.NON-DIM MODETo operate, the TRANS-FLO SYSTEM in the Individual Ballast Dimming Modeyou need a minimum of:TRANS-FLO Power & DimCable, 6ft.Primary power feed line anddimming line ( both withEdison connectors). Onecable per ballast is neededfor individual dimmingcontrol.TRANS FLO Two-LampBallast, 120 VACA standard-output, flickerfree electronic dimmingballast. Operates two 15inch, 2ft, 3ft or 4ft lamps.Lamp w/ Harness ( needtwo per Ballast )15-inch Med Bipin2ft Med Bipin3ft Med Bipin4ft Med Bipin2
3
(A) Attach each TRANS-FLO circular connector tail to a locking lamps harness,or single head extension, making sure to rotate the locking ring until it“clicks” into its locked position. Securely connect both ends to the harnesson the lamp before turning on the power. Each Trans-Flo Ballast MUST havetwo lamps connected to operate.A ballast can operate any two sizes of lamps at the same time. For example,a 15inch lamp can be paired with a 4ft lamp.(B) With the ballast power switched off, attach the Power /Dim Cable to the“POWER IN” port of the ballast.(D) Connect the Primary Power Feed (black) 3-pin U ground Edison plug to a120 Volt AC non-dimming circuit.(E) Connect the Dimming Line (Yellow) U ground Edison plug to a theatricalSCR dimmer circuit.CAUTION: The Primary Power Feed and the Dimming Line must share acommon neutral in order to dim. Failure to do so may result in an electricalshort circuit.One way to ensure a common neutral is to dedicate a number of non-dimmingcircuits on a dimmer rack and then feed the Dimming Line to the appropriatedimming circuits on the same rack.(F) Once the Power/Dim Cable is properly circuited, set the ballast power switchto “DIM”. With 120 Volts AC applied on the Primary Power Feed and with thedimmer up full on the Dimming Line circuit: the ballast will illuminate thelamps and respond to the dimmer settings.Note: To check whether the Primary Power Feed circuit is hot, set the powerselector switch to “NON-DIM”. If there is 120 VAC on the Primary Power Feedcircuit, the ballast will strike the lamps even if the Dimming Line circuit has nosignal.Dimming PerformanceBest dimming performance is achieved by connecting harnesses directly to theballast. When adding Head Extension Cables, add the same length cable toBOTH lamps. Otherwise the lamp with the longer cable will fade out ahead of thelamp with the short cable.4
To operate, the TRANS-FLO SYSTEM in the Series Ballast Dimming Mode youneed a minimum of:TRANS-FLO Power & Dim Cable, 6ft.Primary power feed line and dimming line( both with Edison connectors ). One cableis needed for the first ballast in a series.TRANS FLO Two-Lamp Ballast, 120 VACA standard-output, flicker-free electronicdimming ballast. Operates two 15-inch, 2ft,3ft or 4ft lamps.Lamp w/ Harness ( need two per Ballast )15-inch Med Bipin2ft Med Bipin3ft Med Bipin4ft Med BipinTRANS-FLO Jumper, 10ft & 2ftTo jumper primary voltage from one ballastto the next.5
Dimming PerformanceBest dimming performance is achieved by connecting harnesses directly to theballast. When adding Head Extension Cables, add the same length cable to ALLlamps in a series. Otherwise the lamps with the longer cable will fade out aheadof the lamps with the short cable.6
A maximum of 10 TRANS-FLO Ballasts can be connected on one PrimaryPower Feed Cable.A) Attach each TRANS-FLO circular connector tail to a locking lamps harness,or single head extension, making sure to rotate the locking ring until it “ clicks”into its locked position. Securely connect both ends to the harness on the lampbefore turning on the power. Each Trans-Flo Ballast MUST have two lampsconnected to operate.A ballast can operate any two sizes of lamps at the same time. For example, a15inch lamp can be paired with a 4ft lamp.B) With the ballast power switched off, attach the Power /Dim Cable to the“POWER IN” port of the first ballast in the series.C) Connect a 10ft or 2ft Jumper Cable from the “Power Out” port on the firstballast in the circuit to the “Power In” port of the next ballast. A maximum often ballasts, in series, can be connected in this manner.Jumper Couplers are required to connect two or more Jumper Cables( see Accessories )D) Connect the Primary Power Feed (black) 3-pin U ground Edison plug to a 120Volt AC non-dimming circuit.E) Connect the Dimming Line (Yellow) U ground Edison plug to a theatricalSCR dimmer circuit.CAUTION: The Primary Power Feed and the Dimming Line must share acommon neutral in order to dim. Failure to do so may result in an electricalshort circuit.One way to ensure a common neutral is to dedicate a number of non-dimmingcircuits on a dimmer rack and then feed the Dimming Line to the appropriatedimming circuits on the same rack.F) Once the Power/Dim Cable is properly circuited, set the power switch to “DIM”on all the ballasts in the series. With 120 Volts AC applied on the PrimaryPower Feed and with the dimmer up full on the Dimming Line circuit: theballasts will illuminate the lamps and respond to the dimmer settings.Note: To check whether the Primary Power Feed circuit is hot, set the powerselector switch to “NON-DIM”. If there is 120 VAC on the Primary Power Feedcircuit, the ballast will strike the lamps even if the Dimming Line circuit has nosignal.7
A) Attach each TRANS-FLO circular connector tail to a locking lamps harness,or single head extension, making sure to rotate the locking ring until it“ clicks” into its locked position. Securely connect both ends to the harnesson the lamp before turning on the power.B) With the ballast power switched off, attach the Power /Dim Cable to the“POWER IN” port of the first ballast in the series.D) Connect the Primary Power Feed (black) 3-pin U ground Edison plug to a120 Volt AC non-dimming circuit. You do NOT connect the DimmingLine ( D )to a dimmer circuit.F) Switching the ballast to “NON-DIM” will turn on the lamps.X04-25 SINGLE Head Extension, 25ftX04-12 SINGLE Head Extension, 12 ftBlack, 4-pin male to female. Connects Trans-FloBallast to Single Locking Harness. Maximum of 25ftfrom Ballast to lamp for full dimming range control.HAR-4801HAR-3601HAR-2401HAR-15014ft SINGLE Locking Harness3ft SINGLE Locking Harness2ft SINGLE Locking Harness15” SINGLE Locking HarnessPWC-C TRANS-FLO Jumper CouplerTo combine jumpers if more than 10 ft are requiredbetween ballasts.8
EXP-M&TMounts & Ties Set, 25pkReleasable cable ties and one-inch squareadhesive mounts. Recommended two Sets perlamp.EXP-HLC-T12 Lamp Holder Clip/T12, 24pkMetal Clips to hold T12 ( 1 ½” diameter ) lamps onceilings, walls and set pieces.Recommended two Clips per lamp.Operating Voltage: 120 Volts ACOperating Frequency: 25 KHzAmperage: .70Lamp Current: 420 maLamp Operation: Two Lamps, AnyCombination of 15-inch, 2ft, 3ft or 4ftDimming Range: Full Range toBlackWeight: 3.1lb / 1.4KgDimensions: 13” x 4.5” x 2”33cm x 11.5cm x 5cmEnvironmental: Disposal of Old Electrical & Electronic Equipment.This symbol on the product or on its packaging indicates that this productshall not be treated as household waste. This product is made of recyclablematerials and should be disposed of in accordance with local and stateregulations.Rev 10-04-2005Part No. 3100019Kino Flo, Inc. 2840 N. Hollywood Way, Burbank, CA 91505, USATel: 818 767-6528 website: www.kinoflo.com9
a ballast via a Head Extension ( up to 25ft long ). Jumper Cables link TRANS-FLO Ballasts together ( up to 10 in a series ). The TRANS-FLO SYSTEM operates in three modes: 1. INDIVIDUAL BALLAST DIMMING MODE ( two lamps ) 2. SERIES BALLAST DIMMING MODE (up to 10 ballasts per series ) 3. NON-DIM MODE
Fisher is not associated with Dyna-Flo in any way, nor has Fisher approved or otherwise reviewed any products made by Dyna-Flo. Dyna-Flo 360 Control Valve Fisher ET Control Valve This bulletin includes only common parts for E body valves and actuators. For other materials and parts, including parts for DF363/Fisher EZ, the Dyna-Flo
FLA, FLE, FLI, FLO, FLU Marta Parra Lubary Ester Rebollo Ferrer Margalida Tortella Mateu Rodea los dibujos que tengan el sonido flu Rodea la sílaba fle fla fle fli fla flo fla fli fla fla fla fla flu flu flu fla fle flo fla Rodea la sílaba flu fla fle fli fla flo fla
ELECTRA-flo 5 Series Thermal Airflow Measuring Stations 0 500 1000 1500 2000 2500 3000 3500 4000 4500 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 Airflow Velocity, FPM Resistance to Airflow, inches w.c. E-flo-CM Station Airflow Resistance ELECTRA-flo/S5-CM Stations 0-5000 FPM ELECTRA-flo/S5-MM Stations 0-4000 FP
royal statuario silver dream golden calacatta onyx prestige exotic brown mix floor 60x120 (60x120 - 60x80 - 60x40) ant. sp flo 10 sp flo 22 sp flo 13 sp flo 34 sp flo 44 mos. hexagon 51x29,2 ant. sp es 10p sp es 22p sp es 13p sp es 34p sp es 44p mosaico 30x30 ant./ lux sp mo 103 sp mo
The Rt. Rev. George N. Hunt The Rev. Frederick K. Jellison The Rev. Dn. Ida R. Johnson The Rev. Michaela Johnson The Rev. Paul S. Koumrian The Rev. Canon Harry E. Krauss * The Rev. H. August Kuehl The Rev. Richard T. Laremore * The Rev. Donald A. Lavallee The Rev. Canon John E. Lawrence The Rev. Dr. Gary C. Lemery * The Rev. Dn. Betsy Lesieur *
(Core Class 1A) 5011016X *5008249X 107981X (Left Inlet) Tu-Flo 750 Air Compressor (Core Class 2A) 5004118X Tu-Flo 550 Air Compressor (Core Class 1A) 109251X Tu-Flo 750 Air Compressor (Core Class 2A) 109287X CAT 3306 Core Group 1A Tu-Flo 550 Air Compressor (Core Class 1A) 3406, C10, C12, C15, C16 5002984X (rear end cover studs) 3176, C15 .
Power-Flo LX / Power-Flo II Pump Series . Piping - Flexible Hose, PVC, or Reinforced Hose are all acceptable piping methods For pump outlet use 1-1/2" PVC pipe or reinforced hose. For pump suction on ALL models, use 1-1/2" reinforced hose. Increase size if a long run is needed. For pi
A Reader’s Guide to Contemporary Literary Theoryis a classic introduction to the ever-evolving field of modern literary theory, now expanded and updated in its fifth edition. This book presents the full range of positions and movements in contemporary literary theory. It organises the theories into clearly defined sections and presents them in an accessible and lucid style. Students are .
