Ii Heratherm Thermo Scientific
2012 Thermo Fisher Scientific Inc. All rights reserved.These operating instructions are protected by copyright. Rights resulting thereof, particularly reprint, photomechanicalor digital postprocessing or reproduction, even in part, are only allowed with the written consent of Thermo Fisher Scientific.This regulation does not apply to reproductions for in-plant use.The contents of this operating instructions manual may change at any time and without any prior notice. In case of conflicting translations into foreign languages the German-language version of these operating instructions shall be binding.TrademarksHeratherm is a registered trademark of Thermo Scientific.Thermo Scientific is a brand owned by Thermo Fisher Scientific, Inc.All other trademarks mentioned in the operating instructions are the exclusive property of the respective manufacturers.Thermo Fisher ScientificRobert-Bosch-Straße 1D - 63505 LangenselboldGermanyThermo Electron LED GmbH is an affiliate to:Thermo Fisher Scientific Inc.81 Wyman StreetWaltham, MA 02454USAThermo Fisher Scientific Inc. provides this document to its customers with a product purchase to use in the product operation. This document is copyright protected and any reproduction of the whole or any part of this document is strictlyprohibited, except with the written authorization of Thermo Fisher Scientific Inc.The contents of this document are subject to change without notice.All technical information in this document is for reference purposes only. System configurations and specifications in thisdocument supersede all previous information received by the purchaser.Thermo Fisher Scientific Inc. makes no representations that this document is complete, accurate or error-free andassumes no responsibility and will not be liable for any errors, omissions, damage or loss that might result from anyuse of this document, even if the information in the document is followed properly.This document is not part of any sales contract between Thermo Fisher Scientific Inc. and a purchaser. This documentshall in no way govern or modify any Terms and Conditions of Sale, which Terms and Conditions of Sale shall governall conflicting information between the two documents.iiHerathermThermo Scientific
CContentsChapter 1 Safety Notes . 1-1Basic Operating Precautions . 1-1Operational Safety Rules . 1-2Warranty . 1-2Explanation of Safety Information and Symbols . 1-3Safety Notes and Symbols Used Throughout These Operating Instructions . 1-3Additional Symbols for Safety Information. 1-4Symbols on the Incubator. 1-5Intended Purpose of the Incubator . 1-5Correct Use . 1-5Incorrect Use . 1-5Standards and Directives . 1-5Chapter 2 Delivery of the Incubator. 2-1Packaging . 2-1Acceptance Inspection . 2-1Scope of Supply . 2-2Chapter 3 Installation. 3-1Ambient Conditions. 3-1Location Requirements. 3-1Intermediate Storage. 3-2Room Ventilation. 3-2Space Requirements. 3-3Installation Built-in Units. 3-3Table-top units . 3-4Floor Stand Units . 3-5Transport . 3-7Stacking kit . 3-9Installing the Stacking Feet. 3-9Installing the Stacking Adapter . 3-10Installing the Anti-tilt Anchor . 3-10Floor stand unit spacers . 3-13Chapter 4 Product Description . 4-1Heratherm IGS Series Incubator Overview. 4-1Safety Devices. 4-8Work Space Atmosphere . 4-8Sensing and Control System . 4-8Data Communications & Alarm Interface . 4-9RS-232 Interface. 4-9Thermo ScientificHerathermi
ContentsAC Power Socket. 4-10Fuses. 4-10Work Space Components . 4-10Inner Chamber . 4-10Access Port . 4-10Tube Access Ports. 4-12Chapter 5 Start-up . 5-1Installing the Shelf System for Table-top Units . 5-1Initial Installation . 5-1Installing the Perforated Shelves . 5-2Preparing the Work Space . 5-2Installation of the Support Rails (only for table-top Units) . 5-3Installing the Shelf Support Brackets . 5-3Installing the Perforated Shelves . 5-4Installing/Removing air baffles. 5-5Levelling the Table-top Incubator Unit . 5-6Connecting Power . 5-6Connecting to the Power Supply Source. 5-6Connecting the RS-232 Interface . 5-7Chapter 6 Operation. 6-1Preparing the Incubator. 6-1Starting Operation. 6-1Chapter 7 Handling and Control . 7-1Powering Up . 7-5Switching the Incubator Off / Powering Down . 7-5Temperature Set Value . 7-6Timer . 7-7Stopping a Timer. 7-8Power Outlet . 7-10Settings. 7-11Error Log. 7-11Calibration . 7-12Temperature Display Unit. 7-13Chapter 8 Shut-down . 8-1Shutting the Incubator Down. 8-1Chapter 9 Cleaning and Disinfection. 9-1Cleaning . 9-1Wipe / Spray Disinfection . 9-1Preparing the Manual Wipe/Spray Disinfection . 9-2Predisinfection. 9-3Cleaning . 9-3Final Disinfection . 9-3Chapter 10 Maintenance . 10-1Inspections and Checks . 10-1iiHerathermThermo Scientific
ContentsService Intervals.10-2Preparing Temperature Calibration.10-2Comparison Measurement Procedure.10-3Temperature Calibration Procedure .10-3Replacing the Door Seal .10-4Replacing the Power Cord.10-4Returns for Repair.10-5Chapter 11 Disposal.11-1Overview of Materials Used .11-1Chapter 12 Error Codes.12-1Chapter 13 Technical Data .13-1Chapter 14 Spare Parts and Accessories .14-1Chapter 15 Device Log .15-1Chapter 16 Contact .16-1Thermo ScientificHerathermiii
ContentsivHerathermThermo Scientific
LList of FiguresFigure 3-1 Table-top Incubators, dimensions and required clearances. 3-4Figure 3-2 Floor Stand Incubators, dimensions and required clearances. 3-5Figure 3-3 Floor Stand Incubators, dimensions and required clearances. 3-6Figure 3-4 Lift Points. 3-7Figure 4-1 Heratherm IGS 60/IGS 100/IGS 180 Front View. 4-2Figure 4-2 Heratherm IGS 60/IGS 100/IGS 180 Rear View . 4-3Figure 4-3 Heratherm IGS 400 Front View. 4-4Figure 4-4 Heratherm IGS 400 Rear View. 4-5Figure 4-5 Heratherm IGS 750 Front View. 4-6Figure 4-6 Heratherm IGS 750 Rear View. 4-7Figure 4-7 Sensor System (for table-top units) . 4-8Figure 4-8 Sensor System (for floor stand units) . 4-8Figure 4-9 Signal Interfaces and Power Socket . 4-9Figure 4-10 Shelf System . 4-11Figure 4-11 Tube Access Ports. 4-12Figure 5-1 Sliding the Retaining Spring into the Support Rail . 5-1Figure 5-2 Installing the Shelving . 5-2Figure 5-3 Support Rail Installation. 5-3Figure 5-4 Shelf Support Installation . 5-4Figure 5-5 Installing the Perforated Shelves . 5-4Figure 5-6 Removing the bottom plate . 5-5Figure 5-7 Removing the left and right support profiles. 5-5Figure 5-8 Removing the rear air baffle IGS 400 / 750 . 5-5Figure 5-9 AC Power Supply Socket . 5-7Figure 7-1 Control Panel for Heratherm IGS Series Incubators . 7-1Figure 10-1 Door Seal Replacement .
Thermo Scientific Heratherm 1-1 1 Safety Notes Basic Operating Precautions These operating instructions describe Heratherm incubators. Heratherm incubators have been manufactured to the latest state of the art and have been
Thermo Scientific Heratherm IMC 18 1-1 1 Safety Information Basic operating precautions These operating instructions describe the Heratherm Incubator IMC 18. The Heratherm Incubator IMC 18 has been manufactured to the latest state of the art and been tested thoroughly for flawless functioning prior to shipping. However, the device may present .
Preface Safety and Special Notices ii Thermo Scientific BindIt Software for KingFisher Instruments User Manual Thermo Scientific Thermo Scientific KingFisher Presto User Manual (Cat. no. N17413) Thermo Scientific KingFisher 96 User Manual (Cat. no. 15018890) The Thermo Scientific BindIt Software user manual can be found in PDF format in the
Thermo ScientificThermo Scientific Orion ROSS Ultra, ROSS Ultra Triode and ROSS pH Electrodes 9 and water saturated with KCl. The ratio of methanol to water should be similar to the sample composition. For tips on measuring pH in non-aqueous samples, see Thermo Scientific Water Analysis Instruments Application Note 007.
Thermo Scientific Heraeus Megafuge 8 Centrifuge 12 TX-100 Rotor Thermo Scientific Thermo Scientific Heraeus Megafuge 8 Centrifuge Table 1. Heraeus 230V 50Hz/60Hz Centrifuge Heraeus Megafuge 8 Catalog # 75007211 Weight empty [kg] 3.3 Max. cycle number 50000 Maximum permissible load [g] 16
Thermo Fisher Scientific assumes no liability for any errors or omissions, nor for any damages resulting from the application or use of this information. This manual supersedes all previous editions. No liability for consequential damages Thermo Fisher Scientific shall not be liable for any
Thermo Fisher Scientific Legal Entity Reference Guide Issue Date: April 1, 2014 Expiration Date: October 30, 2014 3 Introduction The Thermo Fisher Scientific Legal Entity Reference Guide is a map to the legal entities within Thermo Fisher. It presents two views of our company information: 1- A cross reference of former brands and product lines
12 Thermo Scientific Multiskan GO User Manual Thermo Fisher Scientific The side view of the Multiskan GO with cuvette instrument is shown in Figure 2-4. Figure 2-4. Multiskan GO with cuvette side view The Multiskan GO supports all common 96- and 384-well plates with and without lids as well as low-volume plates (preferably a high base type).
The protein that is formed? Gene Expression DNA has many regions, some of them are coding regions – the genes which code for proteins, and other regions are non-coding regions which can switch the genes on or off and therefore determine if they will be expressed (if their protein will be produced) or not. Your cells have all of your genes but your cells don’t need to express all of these .
