W. R. Grace & Co.-Conn. Contractor’s Guide
Contr REVISED 2.063/1/063:43 PMPage aG Ice & Water Shield W. R. Grace & Co.-Conn.62 Whittemore AvenueCambridge, MA 02140Contractor’s GuideFor Technical AssistanceCall toll free at 866-333-3SBM (3726).Visit our web sites atwww.graceconstruction.com and www.graceathome.comGrace Ice & Water Shield, Vycor, Bituthene, Basik, Perm-A-Barrier, RIPCORD and Deck Protector are registered trademarks of W. R. Grace & Co.-Conn.Cor-Ten is a registered trademark of USX Corporation.Dens-Deck is a registered trademark of Georgia-Pacific Corporation.We hope the information here will be helpful. It is based on data and knowledge considered to be true and accurateand is offered for the user’s consideration, investigation and verification, but we do not warrant the results to beobtained. Please read all statements, recommendations or suggestions in conjunction with our conditions of salewhich apply to all goods supplied by us. No statement, recommendation or suggestion is intended for any use whichwould infringe any patent or copyright. Grace Construction Products, W. R. Grace & Co.-Conn., 62 Whittemore Ave.,Cambridge, MA 02140.This product may be covered by patents or patents pending.Copyright 2006. W. R. Grace & Co.-Conn.GIWS-101EPrinted in U.S.A. 2/06DA/LI/10MWhereto Use it.How toInstall it.Tips fromthe Pros.
Contr REVISED 2.063/1/063:43 PMPage cGrace Ice & Water Shield Easy measuring for fast, simple installation.What’s in it for youThese convenient reference markings help make installingGrace Ice & Water Shield easier than ever before Where to Apply Grace Ice & Water ShieldCritical Roofing AreasSelection Matrix1-23-4Why Grace Ice & Water Shield is the Best You Can Buy5-6 Ice&ShieldWaterShield Ice&On DemandWaterSplit Release1231How to Apply Grace Ice & Water ShieldConventional MethodBack-Roll Method4Center Line Mark Use as a lap line guide for 2-ply applications Eliminates the need for chalk lines A guide for cutting the sheet into two 457 mm (18 in.) pieces andfor locating the RIPCORD Split Release on Demand 557-89-10Precautions and Limitations11-12Tips from the Pros13-14Application DetailsEavesOption 1: Without Drip Edge Stripped In15Option 2: With Drip Edge Stripped In16Option 3: Extended Perimeter for Existing Roof17Option 4: Extended Perimeter for New Construction18Vertical Front Wall19Vertical Side Wall20Skylight21Chimney22Corner DetailsOutside Corner23Inside Corner24Corner Detailing Patch Options25-2627-28RIPCORD Split Release on DemandGrace Ice & Water Shield is Available in 2 Roll Sizes: 108 sq. ft (3 ft x 36 ft) 225 sq. ft (3 ft x 75 ft)Technical LettersInsulation and Ventilation to Limit Ice Dam FormationUse as an Air and Vapor BarrierExposure GuidelinesSlope RequirementsChemical CompatibilityIn-Place Performance TemperaturesUse Under Architectural Metal RoofingUse Over Fluted Metal DecksFastener SealabilityUse Over Georgia-Pacific Dens-Deck /Dens-Deck PrimeShelf LifeUse on Oriented Strand Board (OSB) Roof SheathingRigid Roof Insulation Boards and Grace Underlayments29303132323334353536373738Membrane in each case is 1.02 mm (40 mil) in thickness as per ASTM D 3767, Method A.Who to Call for Technical Assistance392Lap Lines A guide for overlapping additional sheets for membrane Achieve recommended 90 mm (3.5 in.) side laps (indicated by solidline) by lining up edge of release liner with dashed line duringmembrane application3Small Measurement Marks 152 mm (6 in.) marks for easy measurement; no tape needed4Large Measurement Marks Located every 305 mm (12 in.)
Contr REVISED 2.063/1/063:43 PMPage 1Where to ApplyCRITICAL ROOFING AREASGrace underlayments add very little to the cost of the job – andnothing gives the professional roofer more peace of mind. Also,consider Grace Vycor Self-Adhered Flashings for your critical nonroof flashing details (windows, doors, decks).Grace Ice & Water Shield applied in critical roofing areas canhelp prevent hard-to-correct leak problems caused by moisture penetration due to ice dams, wind-driven rain and more.The product offers superior adhesion to the deck, high qualitylaps, and the highest quality seal around roofing fasteners.Low Slope AreaRake EdgeConfinedRake EdgeAll of the shaded areas below can benefit from the application ofGrace Underlayments and Grace Vycor Self-Adhered Flashingsbeneath the finished roofing, siding and decking materials.ValleySkylightRidgeChimneyEaveEaveHip DormerFlanged WindowsCornersSillExteriorDoors12n Grace Ice & Water Shield n Grace Vycor Sill PlateLedger BoardDeck JoistsPlusn Grace Vycor Deck Protector
Contr REVISED 2.063/1/063:43 PMPage 3Where to ApplyGRACE UNDERLAYMENTS PRODUCTSELECTION MATRIXHow to Use This ChartRead chart from top to bottom. Although Grace Ice &Water Shield is, in many cases, the best product ofchoice, it MUST NOT be used in the desert southwestand/or under roofs made of copper, Cor-Ten or zinc inhigh altitude climates. If you are in the desert southwest,use Grace Ultra.Application GuidelinesGraceUltraGraceIce & WaterShield GraceSelectGraceBasik *Desert Southwest United StatesUnder Copper, Zinc or Cor-Ten in High Altitude ClimatesUnder Architectural Metal RoofsRoofing in High Altitude/Alpine RegionPremium Protection from Severe Ice DamsAs a Vapor BarrierAs a Temporary Roof (see product specificappropriate exposure guidelines)3Best ChoiceGood ChoiceNot Recommended For Use4*For application on wood substrates only
Contr REVISED 2.063/1/063:43 PMPage 5Why Grace Ice & Water Shield is the Best You Can BuyWHAT MAKESIT BETTER?Best Adhesion to the Roof DeckThe time-tested rubberized asphalt formulation in GraceIce & Water Shield provides superior initial and longterm adhesion without primer or nails. This strong bondhelps ensure the user of a watertight installation.LightweightGrace Ice & Water Shield is easy to handle.Can be Left Exposed LongerGrace Ice & Water Shield can be left exposed for up to a full 30 days and caneven be used as a temporary roof.Won’t TelegraphUnlike many thicker membrane underlayments with laps that are visiblethrough roof coverings, Grace Ice & Water Shield remains invisible.Forms Superior LapsUnlike many fully-adhered membrane underlayments,Grace Ice & Water Shield requires NO special treatmentof the laps, making it easy to get a watertight seal.Superior Tear ResistanceGrace Ice & Water Shield uses an extremely strong, cross-laminated,high density polyethylene carrier sheet that offers superior tear resistance,but is easy to cut and detail.Highest Quality Seal Around Roofing FastenersGrace Ice & Water Shield helps deliver premium roof leak protectionvia an aggressive, rubberized asphalt formulation that seals aroundroof covering fasteners.RIPCORD Split Release on Demand5Most Comprehensive UL Fire Classifications and RatingsGrace Ice & Water Shield is UL classified under all classified shingxles foruse in detail areas or for full roof coverage. Grace Ice & Water Shield is theonly membrane underlayment with a fire rating for internal fire resistance.This thin cord (slightly embedded in the rubberized asphalt) allows thesplitting of the release paper in half, making installations in detailedareas (chimneys, valleys, etc.) quick and easy.Longest Performance HistoryRe-RoofableTHE Name Brand in UnderlaymentsUnlike some granular surfaced membranes, Grace Ice & Water Shieldwill not adhere to the underside of the exposed roof covering and canbe applied over Grace underlayments (except over Grace Basik) inretrofit applications, making re-roofing easier, less costly, moredurable and environmentally friendly.Unique Non-Granular Slip ResistanceOffers superior foot traction without the granules or grit that inhibitwatertight laps.Grace Ice & Water Shield offers the longest performance history and thehighest confidence of performance for over 25 years.Grace Ice & Water Shield is a registered trademark of Grace ConstructionProducts. Don’t be fooled by imitators.GRACE ICE & WATER SHIELD IS AVAILABLE ONLY FROM GRACECONSTRUCTION PRODUCTS.6
Contr REVISED 2.063/1/063:43 PMPage 7How to Apply Grace Ice & Water ShieldGrace Ice & Water Shield roofing underlayment is a very user-friendly product. Thereare two easy ways to install it. We call the first The Conventional Method and thesecond The Back-Roll Method.THE CONVENTIONAL METHODRIPCORD Split Release on DemandUse for ease of installation in detailed areas (dormers, valleys, chimneys, etc.)1Step One:2Step Two:3Step Three:Locate RIPCORD at centerof membrane.Contractors tell us that it’s easy to install Grace Ice & Water Shield. ContractorBob Stransky sums it up this way: “Aligning Grace Ice & Water Shield before pullingout the release paper makes an easy installation, free of wrinkles.this method issimple, fast and fool proof.“1237Step One:Cut the membraneinto 3-5 m (10-15 ft.)lengths andre-roll loosely.Peel back 300-600mm (1-2 ft.) ofrelease liner,align membrane.Create a notch in releasepaper at mid-center. Pullback release paper andextract RIPCORD.Pull RIPCORD, splittingrelease paper in half.Step Two:Peel the releaseliner from themembrane.Press themembrane inplace with heavyhand pressure.Step Three:Side laps must bea minimum of90 mm (3.5 in.) andend laps a minimumof 150 mm (6 in.).RIPCORD4For Valleys:Roll out membrane; cut torequired lengths. ExtractRIPCORD following instructionsabove. Position membrane atstart up area aligning center onvalley. Remove one side of therelease paper. Press membraneinto place with hand smoothingoutward towards edge. Repeaton other side of valley.8
Contr REVISED 2.063/1/063:43 PMPage 9How to Apply Grace Ice & Water ShieldTHE BACK-ROLL METHODSome contractors prefer the back-roll method for applying Grace Ice & Water Shield.As contractor Bob Stransky explains, “The back-roll technique can be faster than theconventional method since you can lay down the membrane in just a few minutes! What’smore, you can get the hang of the back-roll technique in no time – it’s simple and it laysthe membrane down evenly.” Here’s how the back-roll method works:91Step One:2Step Two:3Step Three:Start by unrollinga 3-5 m (10-15 ft.)piece of membrane,leaving the releaseliner in place. Alignthe membrane androll in the intendeddirection of the membrane application.Carefully cut therelease liner on topof the roll in thecross direction,being careful not tocut the membrane.Peel back about150 mm (6 in.) of therelease liner in theopposite directionof the intendedmembrane application, exposing theblack adhesive.4Step Four:5Step Five:6Step Six:Hold the releaseliner with onehand and pull theroll along the deckwith the releaseliner, leaving theapplied membranebehind.Stop frequently topress the membrane in placewith heavy handpressure, smoothing the membranetoward the outeredge.When finishedwith the roll, goback and removethe remainingrelease liner.Smooth tothe edge.10
Contr REVISED 2.063/1/063:43 PMPage 11Precautions and LimitationsPRECAUTIONSAND LIMITATIONSSlippery when wet or covered by frost.Consistent with good roofing practice, always wear fallprotection when working on a roof deck.Release liners are slippery. Remove from work areaimmediately after membrane application.Do not leave permanently exposed to sunlight. Maximumrecommended exposure guidelines for Grace Ice & WaterShield is 30 days, Grace Select is 30 days, Grace Basik is30 days, and Grace Ultra is 60 days.Do not fold over the roof edge unless the edge is protected by a drip edge, gutter or other flashing material.Do not install on the chamfered edges of wood plank.Do not install directly on old roof coverings (refer toTechnical Letter 5).Certain product applications are prohibited in hot desertareas in the Southwestern United States. Check withyour Grace representative.11Check with the manufacturer of the metal roofing systemfor any special requirements. Do not install Grace underlayments directly under roof coverings which areespecially sensitive to corrosion (such as zinc) withoutproviding proper ventilation.Do not install Grace Ice & Water Shield, Grace Select orGrace Basik under copper, Cor-Ten , or zinc metal roofingin high altitude climates. These roofs can reachextremely high temperatures due to the low reflectivity,high absorption, and high conductivity of these metals. UseGrace Ultra for these roof types in this climate. Check withyour Grace representative.Provide proper roof insulation and ventilation to help reduceexcessive ice dams and to minimize interior condensation.Grace underlayments are air and vapor barriers.Repair holes, fishmouths, tears and damage with a roundpatch of membrane extending past the damaged area, 150mm (6 in.) in all directions. If fasteners are removed leavingholes in the membrane, it MUST be patched. The membrane may not self-seal open fastener penetrations.Do not install fasteners through the membraneover unsupported areas of the structural deck, such as overthe joints between adjacent structural panels.Due to its slight asphaltic odor, do not apply wheremembrane is exposed to interior living spaces.Grace Ice & Water Shield, Grace Select and Grace Basikare not compatible with EPDM; use Grace Ultra for tie-ins(refer to Technical Letter 5).Grace underlayments are not compatible with polysulfides,flexible PVC, high concentrations of resin (pitch), and othersubstances (for more information refer to Technical Letter 5).SAFETY, STORAGE, AND HANDLINGGrace underlayments and accessory products must be handledproperly. Read all product labels and Material Safety DataSheets (MSDS) for proper handling and disposal. Deliver allmaterials in manufacturer’s unopened packages and store allmaterials under cover. Do not double stack palletized material.12
Contr REVISED 2.063/1/063:43 PMPage 13Tips from the Pros. you’ll save time and moneyDO’SDON’TSBob Stransky, Executive Supervisor,Doc Gelso Construction, Inc.Jim Kenyon, Project Manager and Superintendent,Vermont Roofing Co., Inc.“You should fill in any large gaps on the plywood deckbefore you install Grace Ice & Water Shield. If you don’thave 100% backing for the membrane, nails or fastenerscan go into a gap (air void) and cause leaks.When you have a steep roof application, it is oftenfaster and easier to apply the membrane vertically thanside-to-side. Run your first piece of Grace Ice & WaterShield across the bottom edge of the roof and then runyour strips up and down the roof, with one installer onthe top of the roof and one on the bottom.”Frank Lawson Jr., President,The Lawson Roofing Co., Inc. and Past President of the NRCA“For extra protection against ice dams and water leaks, useGrace Ice & Water Shield with flashing when you’reinstalling it in valleys.If your jobs involve high-quality tile, slate and asphaltshingling systems with long-term life-cycle expectations,you should definitely use Grace Ice & Water Shield.”Jim Kenyon, Project Manager and Superintendent,Vermont Roofing Co., Inc.“In parts of the country where severe ice dams and winddriven rain can cause leaks, use two layers of Grace Ice& Water Shield around the eaves – one directly on top ofthe other with the flashing or perimeter metal inbetween the two membrane layers.”13Jim Rothermel, Supervisor,Cormack Builders“Make sure you take advantage of using the RIPCORD splitrelease feature to realize the full advantage of achievingthe perfect fit, especially in the valleys. RIPCORDcertainly allows for a more efficient, quicker install.”“Don’t take chances with an untested underlayment. Call-backs are expensive. You don’t want tohave to go up there twice.”Ted Toppan, President,Quick Build Co., Inc.“I tell my men, ‘Never lay down the first roll ofGrace Ice & Water Shield without snapping a(chalk) line first.’ Set the reference for the first rollso you can keep a perspective. Once the first rollis down, you can use the lines printed on the product to keep the roof line true.Avoid creating leaks when you’re cutting a pipestack for a plumber. First, put down a 2 ft. x 2 ft.square of Grace Ice & Water Shield before you cutthe hole in the roof. Drill the hole right through theGrace Ice & Water Shield andthe plywood. When you’re readyto poke the pipe through the rubber pipe flange and fasten theflange to the roof deck, the GraceIce & Water Shield patch willimmediately seal the nail holes.”14
Contr REVISED 2.063/1/063:43 PMPage 15Eave – Option 2Visit www.graceconstruction.com for the mostcurrent details and installation video. Refer alsoto product data sheets on our web site for furtherinformation. We hope these will provide information that you’ll find useful.Eave – Option 1IWSDET-102With Drip Edge Stripped InEAVE OPTIONSEAVE OPTIONSAPPLICATION DETAILSIWSDET-101Without Drip Edge Stripped In1. The drip edge is installed over the first layer ofGrace underlayment2. A second layer of Grace underlayment is installedover the drip edge3. Install Grace underlayment to form water shedding laps1. The drip edge is installed over the Grace underlayment152. Install Grace underlayment to form water shedding laps3. Repair all holes left from removal of toe boards,roof jacks, etc.4. Repair all holes left from removal of toe boards,roof jacks, etc.16
3/1/063:43 PMEave – Option 3:Page 17IWSDET-103IWSDET-104Extended Perimeter for New Construction1. The drip edge is installed over the first layer ofGrace underlayment1. RIPCORD Split Release on Demand has been removedalong edge of roof for ease of installationof extended fascia board(s)2. A second layer of Grace underlayment is installed overthe drip edge3. Seal non-water shedding lap with a bead of roof cement4. Install remaining Grace underlayment to form watershedding laps17Eave – Option 4:Extended Perimeter for Existing Roof5. Repair all holes left from removal of toe boards,roof jacks, etc.EAVE OPTIONSEAVE OPTIONSContr REVISED 2.062. The drip edge is installed over the first layer ofGrace underlayment3. Install Grace underlayment to form water shedding laps4. Repair all holes left from removal of toe boards,roof jacks, etc.18
3/1/063:43 PMVertical Front WallPage 19IWSDET-105Vertical Side WallIWSDET-1061. RIPCORD Split Release on Demand has been removed alongjoint between roof and wall for ease of installation1. Extend Grace underlayment on the wall sheathing abovethe highest expected level of snow and ice2. Extend Grace underlayment on the wall sheathing abovethe highest expected level of snow and ice2. Extend Grace underlayment on the roof deck above thehighest expected level of water back-up from ice dams3. The metal flashing is installed over the Grace underlayment3. Extend Grace underlayment beyond eave onto vertical sidewall for protection against run-off from roof4. Install Grace underlayment to form water shedding lapsVERTICAL SIDE WALLVERTICAL FRONT WALLContr REVISED 2.064. The metal flashing is installed over the Grace underlayment195. Install Grace underlayment in order as shown by numbers6. Install Grace underlayment and weather resistive barrier toform water shedding laps20
Skylight3/1/063:43 PMPage 21IWSDET-1071. RIPCORD Split Release on Demand has been removedalong joint between roof and skylight forease of installation2. Install Grace underlayment in order as shown by numbers3. Extend Grace underlayment from eave to below skylightand from above skylight to ridge4. Install Grace underlayment to form water shedding laps5. Install skylight, flashing and roof covering as permanufacturers’ recommendation216. Determine if skylight materials (gasket, flashing, etc.)are compatible with Grace underlayments – refer toTechnical Letter 5ChimneyIWSDET-108CHIMNEYSKYLIGHTContr REVISED 2.061. Prime masonry chimney with Perm-A-Barrier WBPrimer as necessary2. RIPCORD Split Release on Demand has been removedalong roof and chimney for ease of installation3. Install Grace underlayment in order as shown by numbers4. Extend Grace underlayment from eave to below chimneyand from above chimney to ridge5. Install Grace underlayment to form water shedding laps6. Refer to NRCA or SMACNA for metal counterflashing
Where to Apply Grace Ice & Water Shield Critical Roofing Areas 1-2 Selection Matrix 3-4 Why Grace Ice & Water Shield is the Best You Can Buy 5-6 How to Apply Grace Ice & Water Shield Conventional Method 7-8 . Side laps must be a minimum of 90 mm (3.5 in.) and end laps a minimum
Grace Ultra Grace Select Grace Tri-Flex Grace Syn 15 Weather Resistive Barriers & Flashings 71 17 Vycor enV-S Vycor enV Vycor Plus Vycor PRO Basement Waterproofing and Vapor Barriers 27 Grace Bituthene Grace Florprufe Product Data Sheets 33 Grace Ice & Water
All Life is Weak and relies upon the Grace of God to sustain it. We see this Grace in how a mother sustains a Weak child. Grace is the noun. Love is the verb, which means: showing Grace. Lets see how we find Grace in the 3-Square. Once again, the short line on the left is thin, not thick like the bar at the top.
Amazing Grace – Celtic Thunder Amazing grace, how sweet the sound That saved a wretch like me I once was lost but now am found Was blind but now I see believed Twas grace that taught my heart to fear And grace my fears relieved How precious did that grace appear The hour I first Amazing grace, how sweet the sound That saved a wretch like me
Grace College and Seminary Catalog 2020-2021 . Grace Theological Seminary 4 July 2020 . The special collections at the Morgan Library include the papers of the American evangelis t William A. "Billy" Sunday as well as archives of the Winona Lake Bible Conference, Grace College and Seminary, and various Grace Brethren agencies.
Where to Apply Grace Ice & Water Shield Critical Roofing Areas 1-2 Selection Matrix 3-4 Why Grace Ice & Water Shield is the Best You Can Buy 5-6 How to Apply Grace Ice & Water Shield Conventional Method 7-8 Back-Roll Method 9-10 Precautions and Limitations 11-12 Tips from the Pros 13-14 Application Details Eaves Option 1: Without Drip Edge .
Hyundai Sonata 2011-2014 Hyundai Tucson 2010-2015 Hyundai Elantra Coupe 2014 Wire Information Connector Information Hyundai Elantra 2011-2013 Hyundai Elantra 2014-2015 Hyundai Elantra Coupe 2013 *Refer to the next page for a visual representation of each connector. 11 41 50 P - White 16-pin conn. 7 15 J - Gray 39-pin conn. K - White 41-pin conn. 36
Dec 03, 2014 · Stateful architecture is about flows or connections, not packets –Most effective with TCP, UDP, and ICMP . Cisco Public ASA Firewall Family 5 ASA 5550 (5 (1.2 Gbps, 36K conn/s) ASA 5580-20 -10 Gbps, 90K conn/s) ASA 5580-40 (10-20 Gbps, 150K conn/
Animal Nutrition & Health addresses the nutrition additives segment of the feed and pet food markets. Human Nutrition & Health largely addresses nutrition and functional ingredients segment of the food markets. Personal Care is focusing on the actives and ingredients in the sun care, skin care and hair care industries. DSM is the only producer who can supply the lawsuits, and public rejection .
