P- AP Esign Guide - EN-TOUCH
P-CAP Design GuideeN-touch – A Nelson-Miller Brand
Product Features for PCAPElectricalVoltage:2.8 5.5v DCResolution: (Adjustaccording to LCDresolution and ICType)4096 x 4096 MaxInput Type:Conductive pen, stylus orfingerOperation System:Android, Linux, Win7, Win 8, Win CE(Some)Touch VibrationTime: (Dependson IC Type)5 15msOperating Voltage:1.8v, 3.3v, 5v(USB)Touch Point:10 maximumCurrent atWorking:2.5mA (Dependson IC Type)Touch PanelMaterialType:Normal glass, chemical hardenglass (solution), physicalharden glass (heat), PC,acrylic, PETCurrent atSleeping Mode: 0.20mA(Depends on ICType)Touch PanelGlassThickness:Glass: 0.55mm, 0.70mm,1.10mm PET: 0.188mm,0.25mm. PC and acrylic followthickness request. 2.0mm isthe maximum to ensure thesensitivity and accuracy oftouch.Life Expectancy: 200,000,000TouchesSensorThickness:Glass: 0.55mm, 0.70mm,1.10mm Film: 0.125mmOperatingTemperature:-20 Deg C 80deg C (-20 DegeN-touch – A Nelson-Miller Brand
with the condition,T/P not Frozen)OCAThickness:FOCA Thickness: 0.125mm,0.175mm. LOCA thickness:0.15mmStorageTemperature:-30 Deg C 80deg CTouchPressure:Capacitive touch, no touchpressure requiredOperatingInterface:IIC, USB (Seldomuse) InterfaceDepends onOperating SystemChoose.SurfaceHardness;Glass 6H, PET 3HAnti-Interference(Whole Unit TestUnder StaticElectricity):Contact Discharge 8kv GapDischarge 15kvCommon PCAP ConstructionsConstructionG FG F FG GPET GCostLowHighestHighLowestGood YieldLowLowHighHighLight Transmissivity 88% 86% 88% 88%Fog 3% 3% 3% 3% (GlossPET)eN-touch – A Nelson-Miller Brand
Legibility98%98%98%98% (GlossPET)AdvantageLower cost,thinner,surfacehardness isgood.Supports handwriting, max 10touch point,Surfacehardness isgood.Supports handwriting, max 10touch points, goodtransmissivity,surface hardnessis good.Supports handwriting, max 10touch points,goodtransmissivity,low developmentcost.DisadvantageOnly 1 touchpointsupports 2points atvirtual effect.Maximumsize is 4”.High costdevelopment,unit cost is highdue to 2 layersof film used.High developmentcost, lead time islonger, unit cost ishigher. CannotCNC hole onsensor glass.Surface harnessis low due totouch panel isPET.Methods for Circuit ConstructionLaser/ MoAlMo:You can have very fine line widths.0.05mmTooling cost is HIGH, lead timelongereN-touch – A Nelson-Miller Brand
Silk Screen Printing:Line width is not as fine as laser.0.12mmTooling cost is low, lead time better,recommend use silk screen printingif no special requirement.IC Suppliers & DefinitionsIC Suppliers: Goodix FocalTech Neolec Solomon EETI PIXCIR AtmeleN-touch – A Nelson-Miller BrandDefinitions:1.2.3.4.5.6.7.8.PCT: Projected Capacitive TouchAA: Active AreaOD: Outer DimensionalITO Film: PET Coated with ITOITO Glass: Glass Coated with ITOFPC: Flexible Printed CircuitCover Glass: Touch Panel Glass,MUST be Non-ConductiveSensor: Layer Below Cover Glass,Conductive or Called FunctionalLayer, Consist of Glass and Film 2Types.
Information Needed to Start Up ProjectInformation Needed for New PCAP Project Start Up:1. CAD drawing for touch panel (1:1 Ratio needed if given in a PDF file. The file must be clearlyreadable.2. The drawing must indicate the construction of the touch panel, interface, FPC location, andDimensions.3. The location of FPC to fold and assemble into the LCD needs to be indicated so thatengineering can make the proper layout.4. The following information also needed;5.Cover Glass DesignConstructionMin SizeMin Tolerances itcan MeetOutlineNA /- 0.15mmSilk screen line width0.12mm /- 0.15mmSilk screen line pitch0.12mm /- 0.15mmeN-touch – A Nelson-Miller Brand
Distance from AA (active area,) tosilk screen circuit1.50mmNANumber of printing for X or YLength or width ofAA, divide by 6NADistance from outer edge of circuitto edge of outer dimension1.30mmNABevel edge0.15mm /- 0.15mmRadius0.30mm /- 0.15mmSpeaker hole or hole1.40mm /- 0.15mmDistance between hole to hole3.50mm /- 0.15mmDistance between hole to edge4.0mm /- 0.15mmPlease send enquiries for additional information or quotation to:sales@en-touch.comOr call us at (866) 618-1202www.en-touch.comeN-touch – A Nelson-Miller Brand
Atmel Definitions: 1. PCT: Projected Capacitive Touch 2. AA: Active Area 3. OD: Outer Dimensional 4. ITO Film: PET Coated with ITO 5. ITO Glass: Glass Coated with ITO 6. FPC: Flexible Printed Circuit 7. Cover Glass: Touch Panel Glass, MUST be Non-Conductive 8. Sensor: Layer Below Cover Glass, Conductive or Called Functional
Author’s Version Disinformation as ollaborative Work: Surfacing the Participatory Nature of Strategic Information Operations KATE STAR IRD, uman entered esign & ngineering, niversity of Washington AHMER ARIF, uman entered esign & ngineering, niversity of Washington TOM WILSON, uman entered esign & ngineering, niversity of Washingt
26 Critical Lane Analysis for Intersection D esign Carroll J. Messer and Daniel B. Fambro, Texas Transportation Institute, Texas A&M University This paper presents a new critical lane analysis as a guide for designing signalized intersections to serve rush-hour traffic demands.Physical de' sign and signalization alternatives are identified.and methods for evalua-
Unique Identification Authority of India (UIDAI). The AADHAAR-holder can affix his/her eSign on any electronic content by authenticating himself/herself through OTP received on their mobile number registered with AADHAAR. At the backend, the key pair is generated and a Digital Signature Certificate (DSC) is issued by the Certifying Authority (CA).
This paper is include in the Proceedings of the 17t SENI ymposium on etworke ystems esign and Implementation NSDI 20) Feruar 5-27 02 anta lara A SA 978-1-939133-13-7 Open access to the Proceedings of the 17t SENIX ymposium on etorked Systems esign an Implementation (NSDI 20 is sponsore y LocAP: Autonomous Millimeter Accurate
Pre-ESIGN and UETA law of signatures. Per the statute of frauds, certain contracts are enforceable only if there is a written memorandum of the contract signed by or on behalf of the party to be charged Key issue is intent, not the form the signature takes. A signature may be any symbol made or adopted with an
The printed circuit board fabricators are then able to drill the PCBs in groups of three or four, rather than individually sequenced. www.altium.com T 10 F ROBLEM HA FFEC VE C ESIGN Using at Least the Minimum Annular Rings and Employing Teardrops are Tools to Maximize Fabrication Yield 7. UNCONNECTED VIA PADS
esign A 3 ax 2016 Release otes July 20, 2016 Thanks for purchasing, or upgrading to, DesignCAD 3D Max 2016. Here is a detailed look at what's new in this version. New Import/Export feature SketchUp Import - DesignCAD 2016 can now import SketchUp drawings. SketchUp versions
esign uide 2 Common Timber Stairs www.bwfstairscheme.org.uk 5 ntroduction This design guide has been prepared by the British Woodworking Federation
