AWMC-060-8P-4CH 4RGB Output Color Controller
AWMC-060-8P-4CH4RGB Output Color Controllerwww.awled.com
1. Input/Output Interface1. 4 Channel RGB Color Controller：1.IR Sensor：The distance with IR remote controller is 7m 10m.2.USB Connector：Data Edit via USB connector.3.OUTPUT：Signal to LED Module.2. 1 4 RGB Decoder：1.POWER：Power input, 12V or 24V2.INPUT：Receiving signal from Controller3.OUTPUT：To LED Modules, White Line COM or V Red Line Red LEDGreen Line Green LEDBlue Line Blue LEDwww.awled.com
2. AWMC-060-8P-4CH connecting to LED Modules:White Line COM or V 。Red Line Red LEDGreen Line Green LEDBlue Line Blue LEDwww.awled.com
3. AWMC-060-8P-4CH Connecting to DC Power Supply：1 4 RGB.DecoderInput Power：DC 10.5V 26V(Depending on the input voltage of LED module)www.awled.com4 RGB OutputColor Controller
4. AWMC-060-8P-4CH Connecting to LED Modules and PowerSupply：Total output Power:AWMC-060-8P-4CHDC 24V / 240W (Per RGB Channel out put is 60W, totally 240W)DC 12V / 120W (Per RGB Channel out put is 30W, totally 120W)www.awled.com
5. AWMC-060-8P-4CH Connecting to AWCL-060-R SignalRepeater1 4 RGB.DecoderAWCL-060-R4 RGB OutputColor ControllerWhile voltage drops or the consumption of AWMC-060-8P-4CHis full, connect AWCL-060-R at the last LED module for extension.The detailed specification, please see the manual ofAWCL-060-R.AWCL-060-Rwww.awled.com
6. IR SensorIR Sensor-built inIR Sensor- extension (Standrad)There are 2 types of IR sensors, extension mode is standard, andthe wire is 50cm as the photo.www.awled.com
7. IR Remote Controller：1. POWER：POWER ON/OFF.2. PAUSE：P1 P83. M1 M6：Static Mode ( 6 memories)4. SPEED ：P1 P8Dynamic Mode Speeding5. SPEE D -：P1 P8Dynamic Mode Slower6. BRIGHTNESS ： P1 P8PauseDynamic Mode BrighterM1 M6 Static Mode Brighter7. BRIGHTNESS -：P1 P8Dynamic Mode DarkerM1 M6 Static Mode Darker8. CHASE：P1 P8Chasing and non-Chasing9. W：Download of Writing Data via USB port10. DMX ：No Function11. P1 P8：Dynamic Mode ( 8 programs)12. P-CYCLE ：Run cycle for P1 P8www.awled.com
Notice of IR remote controllers:While pressing the button of IR remote controller, the buzzerdoes not ring; maybe there is no signal output from the controllers.Please try to take off the battery, and then install the batteryand try again.If there is no power of the battery, please find another newbattery, the model number is CR2025www.awled.com
8. Installation USB Driver software：1. Inset CD to CD driver2. Click PL-2303 Driver Installer in the folder of PL-2303 Driver forinstallation USB driver.3. After Installation, please apply USB connector to connect to USB port ofcomputerwww.awled.com
4. Click Control Panel5. Click Performance and Maintenancewww.awled.com
6. Click System7. Click Hardwarewww.awled.com
8. Click Device Manager9. Click Ports (COM & LPT)www.awled.com
10. Prolific USB-to-Serial Com Port (COM3) .* Please note this USB port of the computer is COM3* Different USB port and different computer, the USB ports are not the same number.11. Also can find out the number of the USB port by following stepsInstall the USB driver software and ColorEdit 4 RGB software first. Then open the ColorEdit 4RGB software, and then click the selections of COM Port to check how many COM Ports inthe computer.Take USB connector to connect to USB port on computer.www.awled.com
Please open the ColorEdit 4 RGB software and click the selections of COM Port. Then, onenew COM Port is shown. This new shownCOM Port is corresponding to the controller.www.awled.com
9. Installation ColorEdit 4 RGB Software1. Inset CD to CD driver.2. Click dotnetfx3.exe in the folder of dotnetfx3 for installationMicrosoft .NET Framework 3.0.3. Click Setup.exe in the folder of ColorEdit 4 RGB for installationColor Edit 4 RGB software.*Please install dotnetfx3.exe before installing ColorEdit 4 RGB software.*ColorEdit 4 RGB software support Windows ONLY.（Windows 2000 / XP/Vista）.*ColorEdit 4 RGB can not support hardware on server, it can support individualcomputer only.www.awled.com
The instruction for ColorEdit 4 RGB Software：A：Tool Bar.B：COM Port Selections and icons.C：Switching between Program mode and Memory mode.1 ColorEdit 4 RGB Software Interface：A. Tool Bar：1. 【File】： Click【File】 to Open、Save、Save As、Exit.2. 【Edit】: Click 【Edit】 to Copy、Paste.www.awled.com
B. Port selections and icons：COM Port selections：Select the COM Port which is corresponding to controller(Please refer to “Installation USB Driver software” to find out corresponding COMPort).Also can click icon to Open、Save、Save As、Copy、Paste.OpenCopySavePasteSave AsCancelC. Switching to Program Mode or Memory Mode：Switch to Program Mode for editing color or Memory Mode for memorizing editedcolor.1. Program Mode:www.awled.com
A. Setting Part： Setting the Program、Loop、Chase、Speed、Brightnessof the controller：Program：P1 P8 is corresponding to P1 P8 button of the IR controller.Loop：The numbers of the loop, could be 1 99.Chase ： Chase ON is Chasing, and Chase OFF is non-Chasing.Correspond to Chase button of the IR controller.Speed：the number of the speed could be 1 24. 1 is the slowest and 24 isthe fastest. Also can press Speed button/Speed- button onIR controller for adjusting.Brightness：the number of the brightness could be 0 16. 0 is the darkand 16 it the brightest. Also can press Brightness buttonand Brightness- button on the IR controller for adjusting.www.awled.com
B. Selections of colors：Normal Color：There are 112 colors for selections here.User Color：13 colors which are used often could be memorized here.Preview area：Can preview the color here.Mix Color Tray: Selecting the color by clicking. The function of Lightness isfor adjusting the brightness.RGB Set：Creating color by adjust the brightness of R.G.B. (0 255)www.awled.com
C. Color edit part：Step: 1 54 steps of color changing could be edited.Time MUL: 1 10, it means 1 or 2 times time of each step.Color 1 4：Selecting color of each step.Width、High：Changing the width and high of the edit area, it willeasier for users to operate the software.2. Memory Mode：Editing static color. There are 3 parts: Setting, Color Editing and ColorSelecting.www.awled.com
A. Setting：Memory：M1 M6 are corresponding to M1 M6 buttons of the controller.Brightness：The number of the brightness could be 0 16. 0 is the dark,and16isthebrightest.AlsocanpressBrightness /Brightness- button on the IR controller foradjusting the brightness.B. Selections of colors：Normal Color: There are 112 colors for selections here.User’s Color：13 colors which are used often can be memorized here.Preview area：Can preview the brightness.Mix Color Tray: Selecting the color by clicking. The function of Lightness isfor adjusting the brightness.www.awled.com
RGB Set：Creating color by adjust the brightness of R.G.B. (0 255)C. Mixing color edit area:Color 1 4：Editing the color.www.awled.com
The instruction for ColorEdit 4 RGB Software：A. The instruction for reading programs from the controller：1. Turn on the controller and connect USB port with computer.2. Turn on ColorEdit 4 RGB Software, then press (W) button in the IR remotecontroller and select the COM Port number(See page 13,14)3. Controller and Computer are in Connecting mode.4. Selecting a program(P1 P8) in setting part.5. Click (Read) and buzzer will sould, then program in the controller will show onthe screen as shown.As Shown below, software will show (Reading Line XX), XX is the steps of theprogram.www.awled.com
B. Sending program into the Controller1. If Controller and Computer are in connecting mode, see step 4, if not are inconnecting mode, please see from step 2.2. Turn on the controller and connect USB port with computer.3. Turn on ColorEdit 4 RGB Software, then press (W) button in the IR remotecontroller and select the COM Port number(See page 13,14)4. Controller and Computer are in connecting mode.5. Click (Send) and the buzzer will sound and program will send into the controller(P1 P8).As Shown below, software will show (Reading Line XX), XX is the steps of theprogram.www.awled.com
c. Adding color into Editing Programs:1. Editing programs:Moving mouse to chosen color and press left button on mouse, thenpreview part will show the chosen color. And then moving mouse to programpart, press left button could edit color into the program.www.awled.com
2. Editing color into User Color part:After Chosen any color, the color will show in preview part. Moving mouseto User Color and press right button on mouse, the color will show on UserColor.www.awled.com
3. Color Mixing PlateMoving mouse to Color Mixing Plate, press left button on the mouse tochose color, and then chose the Lightness to select the brightness. Thenmoving the mouse and adding color into program.www.awled.com
4. RGB Set:Adjusting the ratio of R.G.B to get the color (See the result in preview color),and then moving mouse to add color into program.www.awled.com
5. Choosing color in program:If User want to copy color from Program into User Color, moving mouseto chosen color and then press “Central Button”(Wheel). Preview part will showthe chosen color. Press right button on mouse, user could add the color intoUser Color.www.awled.com
D.Editing Program:1. If Controller and Computer are not in “Connecting mode”, starting fromstep 2, if they are in connecting mode, starting form step 4.2. Connecting Controller and Computer via USB port and then turn on the power.3. Turn on ColorEdit 4 RGB Software，and select the number of COM Port.4. See Step icon, choose 1 54.5. As former section (Adding Color into Editing Program), adding choosing colorinto the program.6. If user want to delete all the program, click “Clear: icon.7. After editing color, if user want to “send” date into controller, please see formersection: “Sending program into controller”.Editing Same Color, user could apply Copy/Paste function:1. Chosen the part which user want to copy.2. Click the icon of “Copy”3. Moving mouse to the place user want to paste4. Click the icon of “Paste”www.awled.com
www.awled.com
After Editing, user could operate: File Save/File Save As to save the programinto computer. The file could read by operate: File Open or Open.The operation of Memory is similar as Program.www.awled.com
10.M1、M2、M3、M4、M5、M6While the color is changing(In P1 P8), if user press pause, thecolor changing will be stop. At this moment press M1 M6 on IR remotecontroller, the chosen color will memorize in the controller.Press M1 M6, the memorized color will show up.www.awled.com
11. P1 P2 P3 P4 P5 P6 P7 P8, USB Color writing mode:1. Finishing installation of USB driver and ColorEdit 4 RGB software.2. Connecting the USB port on AWMC-060-8P-4CH and Computer.3. Turn on the power of controller, press W on the IR remote controller,then the buzzer in controller will sound. The sound means controlleris under USB color writing mode.4. After Editing the program, press P1 P8 to evaluate the writtenprograms.Notice:If Controller could not connect with computer, or usercould read/write data, please turn off the power and removeUSB port and try again.www.awled.com
12. P - CYCLEPress this button on IR remote controller, the color will run fromP1 P8, it means P1 Æ P2 Æ P3 Æ P4 Æ P5 Æ P6 Æ P7 Æ P8. And thetimes of each program depend on the setting of LOOP on the software.www.awled.com
13. AWMC-060-8P-4CH Specification:Model NumberInput VoltageTotal output powerLED eratureAWMC-060-8P-4CH, RGB Output Color ControllerDC 10.5V 26VAWMC-060-8P-4CH, DC 24V / 240W；DC 12V / 120WConstant voltage140mm x 45mm x 27mm ( L x W x H ) x 2PCS85g x 2PCS0 50 -10 60 LED stripswww.awled.com
8. Installation USB Driver software： 1. Inset CD to CD driver 2. Click PL-2303 Driver Installer in the folder of PL-2303 Driver for installation USB driver. 3. After Installation, please apply U SB c
210-060 210-060 Dumps 210-060 Braindumps 210-060 Real Questions 210-060 Practice Test 210-060 dumps free Cisco Impleme
Modbus RTU 4 Channel Relay Module 4CH Input Optocoupler Isolation RS485 MCU For Arduino Relay communication: multi-unit network 485 communication, based on MBDBUS-RTU protocol, the default communication address is 1, the user can modify the address by command
ABD 050/060 Optimat CNC-Drilling and Dowel Inserting Machine. 02 HOMAG ABD 050/060 Optimat Contents. Horizontal drilling and dowelling in a single machine The Result: YOUR SOLUTION Whether as individual
Class 300 Flat Face Flanges NPS 18 and smaller 0.120, 0.060 Depth (dim NPS 20 and larger 0.190, 0.060 Hub *Diameter of hub at base (dimension X) NPS 5 and smaller 0.030 NPS 6 and larger 0.060 Taper of hub 7 Outside diameter of welding end of welding neck flanges (d
Nominal oD ampacity Cable Weight aWg mils in a* B* lbs/mFT CPB06B 6 7 x 14 0.060 0.300 75 105 116 CPB04B 4 7 x 12 0.060 0.350 95 140 171 CPB02B 2 7 x 10 0.060 0.400 130 190 256 CPB10B 1/0 19 x 14 0.080 0.520 170 260 410 CPB20B 2/0 19 x 12 0.080 0.570 195 300 505 CPB40B 4/0 19 x 10 0.080 0.670 260 405 767 CPB350B 350 MCM 37 x 12 0.095 0.850 350 .
AR.; White River Vocational Technical School, Newport, AR. SPONS AGENCY Arkansas State Dept. of Education, Little Rock. Div. of Vocational and Technical Education. PUB DATE Jun 91 NOTE. 108p.; For the final report, see CE 060 54; for a. related manual, see CE 060 595. PUB TYPE Guides - Non-Classroom Use (055) EDRS PRICE MF01/PC05 Plus Postage.
Page 1 of 7 Spring 2020 RNBS.4631.060 & .061 Nursing Leadership & Management Vicki Jowell, MSN, RN (Section .060) BRB 2280 Telephone: 903-566-7194
AGMA and/or DIN standards IMPERIAL Series Load Rating Drum Capacity METRIC Series Power Supply Line Speed Clutch Load Rating Drum Capacity Power Supply Line Speed Clutch PERFORMANCE 4WS9M18 4WS16M20 4WS26M26 4WS1M6 4WS3M10 4WS6M12 10,000 lbs 16,000 lbs 26,200 lbs 1,500 lbs 3,700 lbs 6,400 lbs 5–10 hp 7.5–15 hp 10–25 hp.5–1.5 hp 1–3 hp .
