2020 Ham Catalog Amateur Radio Towers
2020 Ham CatalogAmateur Radio TowersTashjian Towers Corporation has the objective of engineering, designing, and manufacturing the bestcrank-up towers in the world. This catalog covers the crank-up tower line of products.The purpose of this catalog is to provide our customers with details of the products that TashjianTowers supplies. The catalog has general information, tower specifications, and a price list. The catalog lists projected areas for 100 MPH wind. Wind speed requirements may be higher or lower in yourspecific location. In the event there may be a question of compliance in the design of a tower to state,local, building codes, special engineering calculations and drawings can be prepared at a modestcost.When a customer orders a tower, the ship date, shipping expenses, sales tax, will be determined.Written quotations will be provided and a signed proposal will constitute an order to proceed. Payment is due upon shipment. New towers orders will require a deposit.Engineered TowersTashjian Towers are engineered by licensed professional engineers to hold today’s bigger amateur antennas. Tashjian Towers are rated to meets the current TIA 222 Standard, Rev. “H”code. Tashjian Towers are designed to meet todays building codes, anything less is substandard.Superior StrengthTashjian use of high strength tubing allows for larger antennas at higher wind speeds. Wseries towers have pulley frames on one side, LM-series tower 2 sides, and DX-series towersall three sides.All Tashjian Towers include the tower base, an operation manual, and winch. Delivery or leadtime are 3 months but Tashjian is currently building towers to ship from stock which will reduce lead times. By comparison, the cost to ship a Tashjian Tower is usually lower than othercrank up tower manufacturers. Installation is available in California by Tashjian Towers, a licensed California contractor.
Model No. MW33TYPE: Self-supporting, extendable, manual crank-up tower.SPECIFICATIONS:TOWER HEIGHT: Extended 32’ – 6”. Retracted 11’ – 6”.TOWER SUPPORT: Self-supporting, no guys.WIND LOADING: Engineering analysis indicates the tower will support anantenna with an equivalent effective projected area of 45-ft2 at a basicwind speed of 100 MPH, 3-second gust per ANSI/TIA-222-H.DEAD LOAD: The maximum antenna dead load is 250 lbs.WEIGHT: The tower with the base weighs 250 pounds.SECTIONS: The tower is made from four each 10 foot sections, #4, #5,#6 and #7 is the base.DESCRIPTION:Tower includes a manual crank-up winch and hoisting cables, and a rigidconcrete base mount. The tower is designed to extend the tower telescoping sections uniformly. Tower engineering is no longer included inthe price of tower. Stamped prints and calculations for building permitswill need to be purchased separately.This tower has a pulley frame on one face only. The lifting cable is 1/4 x 7x 19 aircraft cable.High strength tubing and solid rod bracing allow for an efficient towerdesign, yet save weight, resist torsional load and reduce wind resistance,allowing more useful load to be installed on the tower.ACCESSORIES:RCB-54 LT (#7 Wide Section)CO-4 for MW-33TA-54 Special#4 rotator platesCable Kit for MW-33MastsMW-33 Manual,Drawings & CalculationsReplacement PulleysTB-2 Thrust BearingManual WinchPART# 433-4000 4,437.00 USD
Model No. WT-51TYPE: Self-supporting, extendable, manual crank-up tower.SPECIFICATIONS:TOWER HEIGHT: Extended 51’. Retracted 21’-6”.TOWER SUPPORT: Self-supporting, no guys.WIND LOADING: Engineering analysis indicates the tower will support an antenna with an equivalent effective projected area of 12-ft2at a basic wind speed of 100 MPH, 3-second gust per ANSI/TIA222-H.DEAD LOAD: The maximum antenna dead load is 250 lbs.WEIGHT: The tower with the base weighs 355 pounds.SECTIONS: The tower is made from three each 20 foot sections,#4, #5, and #6 is the baseDESCRIPTION:Tower is complete with a manual crank-up winch and hoisting cables,and a rigid concrete base mount. The tower is designed to extend thetelescoping sections uniformly. Stamped prints and calculations forbuilding permits will need to be purchased separately. Price of towerincludes base, winch, and manualThis tower has pulley frame on one face only. The lifting cable is 1/4 x7 x 19 aircraft cable.High strength tubing and solid rod bracing allow for an efficient towerdesign, yet save weight, resist torsional load and reduce wind resistance, allowing more useful load to be installed on the tower.ACCESSORIES:RCB-37LT (#6 Wide Section)WT-51 Drawings, CalculationsTB-2 Thrust BearingCO-3 for WT-51MastsTA-51#4 Rotator PlatesReplacement PulleysCable Kit for WT-51Manual WinchPART# 451-4000 3,621.00 USD
Model No. WT-67TYPE: Self-supporting, extendable, manual crank-up tower.SPECIFICATIONS:TOWER HEIGHT: Extended 67’. Retracted 21’-6”.TOWER SUPPORT: Self-supporting, no guys.WIND LOADING: Engineering analysis indicates the tower will support an antenna with an equivalent effective projected area of 11-ft2at a basic wind speed of 100 MPH, 3-second gust per ANSI/TIA222-H.DEAD LOAD: The maximum antenna dead load is 250 lbs.WEIGHT: The tower with the base weighs 700 pounds.SECTIONS: The tower is made from three each 20 foot sections,#4, #5, #6 and #7 is the baseDESCRIPTION:Tower is complete with a manual crank-up winch and hoisting cables, and a rigid concrete base mount. The tower is designed toextend the telescoping sections uniformly. Stamped prints and calculations for building permits will need to be purchased separately.Price of tower includes base, winch, and manualThis tower has pulley frame on one face only. The lifting cable is1/4 x 7 x 19 aircraft cable.High strength tubing and solid rod bracing allow for an efficienttower design, yet save weight, resist torsional load and reducewind resistance, allowing more useful load to be installed on thetower.ACCESSORIES:RCB-54LT (#7 Wide Section)W-67 Manual, Drawings,& CalculationsTB-2 Thrust BearingCO-3 for WT-67MastsTA-54#4 Rotator PlatesReplacement PulleysCable Kit for WT-67Manual WinchPART# 467-4000 5,916.00 USD
Model No. LM-237TYPE: Self-supporting, extendable, crank-up tower.SPECIFICATIONS:TOWER HEIGHT: Extended 37’. Retracted 20’ - 6”.TOWER SUPPORT: Self-supporting, no guys.WIND LOADING: Engineering analysis indicates the tower will supportan antenna with an equivalent effective projected area of 20-ft2 at abasic wind speed of 100 MPH, 3-second gust per ANSI/TIA-222-H.DEAD LOAD: The maximum antenna dead load is 350 lbs.WEIGHT: The tower with the base weighs 325 pounds.SECTIONS: There are two each 20 foot sections #5 and #6.DESCRIPTION:Tower is complete with a manual crank-up winch and hoistingcables, and a rigid concrete base mount. Top drilled for TB2 bearing. Note: most rotators will fit inside top section. Stamped printsand calculations for building permits will need to be purchased separately. Price of tower includes base, winch, and manual The hoisting cablesystem designed to extend the tower telescoping uniformly.This tower has pulley frames on two faces. The lifting cable is 1/4x 7 x 19 aircraft cable.High strength tubing and solid rod bracing allow for an efficienttower design, yet save weight, resist torsional load and reducewind resistance, allowing more useful load to be installed on thetower.ACCESSORIES:RCB-37LT (#6 Wide Section)Cable Kit for LM-237CO-3 for LM-237TA-37TB-2 Thrust Bearing#5 Rotator PlatesManual WinchPART# 437-4000 2,856.00 USD
Model No. LM-354TYPE: Self-supporting, extendable, crank-up tower.SPECIFICATIONS:TOWER HEIGHT: Extended 53’-9”. Retracted 21’-6”.TOWER SUPPORT: Self-supporting, no guys.WIND LOADING: Engineering analysis indicates the tower will support anantenna with an equivalent effective projected area of 18-ft2 at a basicwind speed of 100 MPH, 3-second gust per ANSI/TIA-222-H.DEAD LOAD: The maximum antenna dead load is 350 lbs.WEIGHT: The tower with the base weighs 660 pounds.SECTIONS: The tower is made from three each 20 foot sections #5, #6and #7.DESCRIPTION:Tower is complete with a manual crank-up winch and hoisting cables,and a rigid concrete base mount Stamped prints and calculations forbuilding permits will need to be purchased separately. Price of towerincludes base, winch, and manual. Hoisting cable system designed toextend the telescoping sections uniformly.This tower has a pulley frame on two faces. The lifting cable is1/4 x 7 x 19 Aircraft cable.High strength tubing and solid rod bracing allow for an efficient towerdesign, yet save weight, resist torsional load and reduce wind resistance, allowing more useful load to be installed on the tower.ACCESSORIES:RCB-54LT (#7 Wide Section)Cable Kit for LM-354ECO-3 for LM-354EManual WinchTA-54TB-2 Thrust Bearing#5 Rotator PlatePART# 454-4000 5,151.00 USD
Model No. LM-354HD and HDSPTYPE: Self-supporting, extendable, crank-up tower.SPECIFICATIONS:TOWER HEIGHT: Extended 54’. Retracted 21’-6”.TOWER SUPPORT: Self-supporting, no guys.WIND LOADING: Engineering analysis indicates the tower will supportan antenna with an equivalent effective projected area of 45-ft2 at abasic wind speed of 100 MPH, 3-second gust per ANSI/TIA-222-H.DEAD LOAD: The maximum antenna dead load is 450 lbs.WEIGHT: The tower with the base weighs 960 pounds.SECTIONS: The tower is made from three each 20 foot sections #6,#7 and #8.DESCRIPTION:Tower is complete with a gearbox, drum and hoisting cables, and arigid concrete base mount. Stamped prints and calculations for buildingpermits will need to be purchased separately. Price of tower includesbase, winch, and manual. Hoisting cable system designed to extendthe telescoping sections uniformly.The LM-354HD uses a manual crank on the gearbox to extend andretract the tower. This tower does have a positive pull down.The LM-354HD SP is a motorized version of the above tower, the 3/4HP electric motor comes with an electric control box and two limitswitches. This tower has a positive pull down and has the largest topsection offered.“Positive Control” worm gear winch permits the raising and lowering ofLM towers without the aid of stops or locks. LM-354HD & 354HDSPuses a 50:1 ratio winch.This tower has a pulley frame on two faces. The lifting cable for the LM-354HD is 1/4 7 x 19 aircraft cable and 1/4” 6 x 36 for the 354HDSP.ACCESSORIES:RCB-70LT (#8 Wide Section)Cable Kit for LM-354HDCO-3 for LM-354HDTA-70TB-2 Thrust BearingManual Winch#6 Rotator PlatesPART# 455-4000 MANUAL 7,191.00 USDPART# 456-4000 MOTORIZED 9,231.00 USD
Model No. LM-470TYPE: Self-supporting, extendable, crank-up tower.SPECIFICATIONS:TOWER HEIGHT: Extended 69’-6”’. Retracted 25’-6”.TOWER SUPPORT: Self-supporting, no guys.WIND LOADING: Engineering analysis indicates the tower will supportan antenna with an equivalent effective projected area of 24-ft2 at abasic wind speed of 100 MPH, 3-second gust per ANSI/TIA-222-H.DEAD LOAD: The maximum antenna dead load is 450 lbs.WEIGHT: The tower with the base weighs 1,200 pounds.SECTIONS: The tower is made from 4 each 20 foot sections #5, #6,#7 and #8.DESCRIPTION:Tower is complete with a gearbox, drum hoisting cables, and a rigidconcrete base mount. Hoisting cable system designed to extend thetelescoping sections uniformly. Stamped prints and calculations forbuilding permits will need to be purchased separately. Price of towerincludes base, winch, and manualThe LM-470 is motorized, and includes 3/4 HP electric motor, electriccontrol box and two limit switches wired for 110. This tower has apositive pull down.“Positive Control” worm gear winch permits the raising and lowering ofthe tower sections without the aid of stops or locks. LM-470 uses a50:1 ratio winch.This tower has a pulley frame on two faces and uses 1/4” 7 x 19 aircraft cable.ACCESSORIESRCB-70LT (#8 Wide Section)LM-470 Manual, Drawings, CalculationsCO-4 for LM-470Replacement PulleysTA-7020’ 10’ Masts#5 Rotor PlatesTB-2 Thrust BearingCable Kit for LM-470RLTPART# 470-4000 10,404.00 USD
Model No. DX-70TYPE: Self-supporting, extendable, crank-up tower.SPECIFICATIONS:TOWER HEIGHT: Extended 70’. Retracted 24’-6”.TOWER SUPPORT: Self-supporting no guys.WIND LOADING: Engineering analysis indicates the tower will support an antennawith an equivalent effective projected area of 45-ft2 at a basic wind speed of100 MPH, 3-second gust per ANSI/TIA-222-H.DEAD LOAD: The maximum antenna dead load is 500 lbs.WEIGHT: The tower with the base weighs 1975 pounds.SECTIONS: The tower is made from 4 each 20 foot sections #6, #7, #8and #9.DESCRIPTION:Tower is complete with a gearbox, drum, hoisting cables, and a rigid concrete base mount. Hoisting cable system designed to extend the telescopingsections uniformly. Stamped prints and calculations for building permits willneed to be purchased separately. Price of tower includes base, winch, andmanual.The DX-70 is a motorized with a 1 HP electric motor, electric control box andtwo limit switches wired for 220 V. This tower has a positive pull down.“Positive Control” worm gear winch permits the raising and lowering of DXtowers without the aid of stops or locks. DX-70 uses a 50:1 ratio winch.This tower has a pulley frame on 3 faces and uses 5/16” x 7 x 19 aircraftcable.ACCESSORIES:RCB-86 LT (#9 Wide Section)TB-2 Thrust BearingCO-4 for DX-86Masts, 10’ 20’TA-86Replacement Pulleys#6 Rotator PlatesDX-70 manual, Drawings&CalculationsCable Kit for DX-70RLT (Remote)PART NUMBER: 480-4000 15,606.00 USD
Model No. DX-86TYPE: Self-supporting, extendable, crank-up tower.SPECIFICATIONS:TOWER HEIGHT: Extended 86’. Retracted 22’.TOWER SUPPORT: Self-supporting no guys.WIND LOADING: Engineering analysis indicates the tower will support anantenna with an equivalent effective projected area of 26-ft2 at a basic windspeed of 100 MPH, 3-second gust per ANSI/TIA-222-H.DEAD LOAD: The maximum antenna dead load is 400 lbs.WEIGHT: The tower with the base weighs 2100 pounds.SECTIONS: The tower is made from 5 each 20 foot sections #5, #6, #7,#8 and #9.DESCRIPTION:Tower is complete with a gearbox, drum, hoisting cables, and a rigid concrete base mount. Hoisting cable system designed to extend the telescoping sections uniformly. Stamped prints and calculations for building permitswill need to be purchased separately. Price of tower includes base, winch,and manualThe DX-86 is a motorized with an 1 HP electric motor, electric control boxand two limit switches wired for 220 V. This tower has a positive pulldown. “Positive Control” worm gear winch permits the raising and loweringof DX towers without the aid of stops or locks. DX-86 uses a 50:1 ratiowinch.This tower has a pulley frame on 3 faces and uses 5/16” 6 x 36 aircraftcable.ACCESSORIES:RCB-86 LT (#9 Wide Section)TB-2 Thrust BearingCO-6 for DX-86MastsTA-86Replacement Pulleys#5 Rotator PlatesDX-86 manual, Drawings, CalculationsCable Kit for DX-86RLT (Remote)PART# 481-4000 16,779.00 USD
Model No. DX-100TYPE: Self-supporting, extendable, crank-up tower.SPECIFICATIONS:TOWER HEIGHT: Extended 100’. Retracted 32’.TOWER SUPPORT: Self-supporting no guys.WIND LOADING: Engineering analysis indicates the tower will support anantenna with an equivalent effective projected area of 24-ft2 at a basic windspeed of 100 MPH, 3-second gust per ANSI/TIA-222-H.DEAD LOAD: The maximum antenna dead load is 400 lbs.WEIGHT: The tower with the base weighs 2500 pounds.SECTIONS: The tower is made from 6 each 20 foot sections #4, #5, #6,#7, #8 and #9.DESCRIPTION:Tower is complete with a gearbox, drum, hoisting cables, and a rigid concrete base mount. Hoisting cable system designed to extend the telescopingsections uniformly. Stamped prints and calculations for building permits willneed to be purchased separately. Price of tower includes base, winch, andmanualThe DX-100 is a motorized tower, with a 1 1/2 HP electric motor and comeswith an electric control box and two limit switches wired for 220 volts Thistower has a positive pull down. “Positive Control” worm gear winch permitsthe raising and lowering of DX towers without the aid of locks. DX-100 uses a50:1 ratio winch.This tower has a pulley frame on 3 faces and uses 5/16 x 5 x 36 aircraftcable.ACCESSORIES:RCB-86 LT (#9 Wide Section)TB-2 Thrust BearingCO-6 for DX-100Masts, 20’ 10’TA-86Replacement Pulleys#4 Rotator PlatesDX-100 manual, Drawings&CalculationsCable Kit for DX-100RLT (Remote)PART# 482-4000 29,070.00 USD
Model No. DX-70HDTYPE: Self-supporting, extendable, motorized heavy duty crank-uptower.SPECIFICATIONS:TOWER HEIGHT: Extended 70’. Retracted 25’.TOWER SUPPORT: Self-supporting no guys.WIND LOADING: Engineering analysis indicates the tower will support anantenna with an equivalent effective projected area of 80-ft2 at a basicwind speed of 100 MPH, 3-second gust per ANSI/TIA-222-H. ExposureC, No Crest, TopoThis tower is suggested for high wind areas where heavy loading is required.DEAD LOAD: The maximum antenna dead load is 500 lbs.WEIGHT: The tower with the base weighs 2,700 pounds.SECTIONS: The tower is made from 4 each 20 foot sections #7, #8, #9and #10.DESCRIPTION:Tower is complete with a 100:1 gearbox, 1.5 hp electric motor, drum,dual 5/16 x 6 x 36 aircraft lift cables, positive pull down and a rigid concrete base mount, RCB #10. The tower is designed to extend the telescoping sections uniformly. Stamped prints and calculations for buildingpermits will need to be purchased separately. Price of tower includesbase, winch, and manualThe DX-70HD has pulley frames on all three sides.High strength tubing and solid rod bracing allow for an efficient towerdesign, yet saves weight, resists torsional load and reduces wind resistance, allowing more useful loads to be installed on the tower.ACCESSORIES:DX-70HD manual,Drawings &CalculationsRCB #10TB-2 Thrust BearingCO-4 for DX-70HDMasts, 20’ 10’TA #10Replacement Pulleys#7 Rotator PlatesCable Kit for DX-70HDRLT (Remote)PART# 483-4000 22,899.00 USD
Model No. DX-86HDTYPE: Self-supporting, extendable, motorized heavy duty crank-uptower.SPECIFICATIONS:TOWER HEIGHT: Extended 86’. Retracted 26’.TOWER SUPPORT: Self-supporting no guys.WIND LOADING: Engineering analysis indicates the tower will support anantenna with an equivalent effective projected area of 24-ft2 at a basicwind speed of 100 MPH, 3-second gust per ANSI/TIA-222-H., ExposureC, No Crest, TopoThis stronger tower is suggested for high wind areas where heavy loadingis required.DEAD LOAD: The maximum antenna dead load is 500 lbs.WEIGHT: The tower with the base weighs 3,000 pounds.SECTIONS: The tower is made from 5 each 20 foot sections #6, #7,#8, #9 and #10.DESCRIPTION:Tower is complete with a 100:1 gearbox, 1.5 hp electric motor, drum,dual 5/16 x 6 x 36 aircraft lift cables, positive pull down and a rigid concrete base mount, RCB #10. The tower is designed to extend the telescoping sections uniformly. The DX-86HD has pulley frames on all threesides. Stamped prints and calculations for building permits will need to bepurchased separately. Price of tower includes base, winch, and manualHigh strength tubing and solid rod bracing allow for an efficient towerdesign, yet saves weight, resists torsional load and reduces wind resistance, allowing more antenna loads to be installed on the tower.ACCESSORIES:DX-86HD manual, Drawings, CalculationsRCB #10TB-2 Thrust BearingCO-5 for DX-86HDMasts, 20’ 10’TA #10Replacement Pulleys#6 Rotator PlatesCable Kit for DX-86HDRLT (Remote)PART# 484-4000 24,582.00 USD
Model No. DX-100HDTYPE: Self-supporting, extendable, motorized heavy duty crank-uptower.SPECIFICATIONS:TOWER HEIGHT: Extended 100’. Retracted 32’.TOWER SUPPORT: Self-supporting no guys.WIND LOADING: Engineering analysis indicates the tower will support an antenna with an equivalent effective projected area of 40-ft2 at a basic windspeed of 100 MPH, 3-second gust per ANSI/TIA-222-H. Exposure C, NoCrest, TopoThis tower is suggested for high wind areas where heavy loading is required.DEAD LOAD: The maximum antenna dead load is 500 lbs.WEIGHT: The tower with the base weighs 3,400 pounds.SECTIONS: The tower
2020 Ham Catalog Amateur Radio Towers Engineered Towers Tashjian Towers are engineered by licensed professional engineers to hold today’s bigger am-ateur antennas. Tashjian Towers are rated to meets the current TIA 222 Standard, Rev. “H” code. Tashjian Towers are designed to meet todays building codes, anything less is substand-ard.
The Amateur Radio Service (HAM) is a licensed radio service for many radio bands and many radio types CERT teams often use HAM radios that are handheld portable devices call handy talkies (HT’s) on the 2M (VHF) or 440 (UHF) bands HT radios on these bands provide very good clarity over a much longer range than GMRS HAM radio is a . /p div class "b_factrow b_twofr" div class "b_vlist2col" ul li div strong File Size: /strong 702KB /div /li /ul ul li div strong Page Count: /strong 25 /div /li /ul /div /div /div
Mission Statement: The Brainerd Area Amateur Radio Club is comprised of about 85 licensed Amateur Radio Operators who meet monthly to exchange ideas, improve radio skills, organize activities that are of service to the area, promote development of Amateur Radio, and
Produced by The Cherokee County Amateur Radio Society, 1/23/2018, for non-profit, non-commercial use ONLY 2 T1A - Amateur Radio Service: purpose and permissible use of the Amateur
tentang Hak Asasi Manusia (HAM)13. Dengan diundangkannya UU HAM telah mengamanatkan Negara khususnya pemerintah untuk perlindungan, pemajuan, penegakkan, dan pemenuhan HAM warga negaranya14. Dalam UU HAM juga telah menentukan adanya sebuah lembaga yang mengurusi masalah HAM, yaitu Komisi Nasional Hak Asasi Manusia (Komnas HAM).
In less than 45 minutes Mary was a pro in ham radio! She told me that later that evening she turned to Doug in a quiet moment and said she wanted to become a ham radio operator too. Mary began studying for her license soon after her first involvement with ham radio. A few months later, Mary took her technician exam on 12-12-12.
Through books, tapes, maps, and a list of ARRL-affiliated ham clubs, you will be able to find the answers to all your questions about amateur Radio. Gordon West Radio School 1-714-549-5000 E-mail: wb6noa@arrl.net Gordon West teaches evening ham radio classes and offers we
What is amateur (ham) radio? Amateur radio, also known as ham radio, is a hobby enjoyed by hundreds of thousands of . AC power circuits, hazardous voltages, fuses and circuit breakers, grounding, lightning protection, battery safety, electrical code compliance Ant
Short presentation on archaeological illustration generally. Introduction to pottery illustration, the equipment and the layout, presentation and conventions commonly used. Demonstration of how to draw a rim, followed by practical session Session 2 - 11th Oct. 1- 4.30pm. - Nadia Knudsen Presentation and demonstration of how to draw a pot base and a complete profile of a vessel followed by a .
