QUICK REFERENCE Stock Sub-FHP Gearmotors

2y ago
15 Views
2 Downloads
1.91 MB
20 Pages
Last View : 19d ago
Last Download : 5m ago
Upload by : Jerry Bolanos
Transcription

QUICK REFERENCEStock Sub-FHP GearmotorsAC Single & Three PhaseGearmotorsParallel ShaftPZ SeriesGearmotorsP240 & P300 SeriesGearmotorsSingle Phase 115V12-100 In-LbsOutput TorquePage 102DC SCR 90 & 180V10-100 In-LbsOutput TorqueLow Voltage (12V)36-100 In-Lbs torquePage 92Single Phase 115/230V43-391 In-LbsOutput TorquePage 103DC SCR 90 & 180V27-353 In-LbsOutput TorqueLow Voltage (12V)113-353 In-Lbs torquePage 93DC SCR 90VandLow Voltage (12V)Output Torque130-268 In-LbsPage 94OS300 SeriesGearmotorsPE350 SeriesGearmotorsSingle Phase 115/230V25-341 In-LbsOutput TorqueThree Phase 230/460V55-320 In-LbsOutput TorquePage 104DC SCR 90 & 180V25-371 In-LbsOutput TorqueLow Voltage (12V)155-341 In-Lbs torquePage 95P1100 SeriesGearmotorsSingle Phase 115/230V70-1105 In-LbsOutput TorqueThree Phase 230/460V70-1105 In-LbsOutput TorquePage 105DC SCR 90V105-1112 In-LbsOutput TorqueLow Voltage (12V)320-1087 In-Lbs torquePage 96Single Phase 115/230V14-113 In-LbsOutput TorquePage 106DC SCR 90 & 180V5-135 In-LbsOutput TorqueLow Voltage (12V)25-135 In-Lbs torquePage 97Right-AngleWorm Type10 & 13 SeriesGearmotorsBravo RightAngleWorm Type12 SeriesGearmotors90DC SCR & Low VoltageDC SCR 90VandLow Voltage (12V)Output Torque46-134 In-LbsPage 98

QUICK REFERENCEStock Sub-FHP IP55 WASHGUARD GearmotorsPE350 SeriesGearmotorsDC SCR 90VandLow Voltage (12V)Output Torque25-341 In-LbsPage 100Right-Angle13 SeriesGearmotorsDC SCR 90VandLow Voltage (12V)Output Torque50-135 In-LbsPage 101GearmotorsP300 SeriesGearmotorsDC SCR 90VandLow Voltage (12V)Output Torque44-353 In-LbsPage 99Stock Sub-FHP Three Phase Inverter Rated GearmotorsIncludes gearmotorseries PZ, P240,PE350 and 13 seriesright-angleThree phase 230V12-391 In-LbsOutput TorquePage 10891

SUB-FHP DC GEARMOTORSPARALLEL SHAFT GEARMOTORSGearmotorsSCR RATED:10-100 In-Lbs TorqueLOW VOLTAGE:36-100 In-Lbs TorqueElectricalSpecifications:SCR Rated GearmotorsTotally enclosed,permanent magnet DCgearmotors, performancematched for continuous duty service over a60:1 speed range. All have constant torquethroughout the range when powered by a full-waveunfiltered SCR-type adjustable speed control havinga typical form factor of 1.3 to 1.4.Low Voltage GearmotorsTotally enclosed, permanent magnet DC gearmotors,performance matched for continuous duty. Motorsare designed for battery power or can be used with alow voltage controller with form factor up to 1.05.Mechanical Specifications:Precision machined in-line steel gears, with a firststage steel helical gear followed by spur-type gears.Lubrication is permanent semi-fluid grease, reducingpossibility of leakage. Output shafts have needlebearings for high load capacities. Shafts arehardened steel.Conduit box not included with motor. Optionalconduit box and PZ gearmotor mounting bracketshown on page 107.Application Notes:These gearmotors are designed for mounting at anyangle, but motor below the reducer should beavoided to prevent leakage of lubricant into the motorshould the motor shaft seal fail.The motor’s stall torque could exceed recommendedfull load torques. If this service is anticipated, acurrent limiting device should be used. This issue iseven more critical for low voltage motors, typically nocontroller is used since motor connected directly tobattery, so some type of current limit or fusing shouldbe considered.Overhung load capacities shown are at center ofoutput shaft.Model PZ gearmotors have the same mountingdimensions as Bodine model D and Z, Baldor/Boehm, Bison 100 gearmotors, and a number ofDayton gearmotors.For additional information, see Bulletin 1830.PZ SERIES DC SCR RATEDPARALLEL SHAFT TENV 1.0 SERVICE berListPrice GearmotorType &FrameRatioto 4401 40 M1115002 404PZ5-30A 450900.461553.003.259.287.724401 40 M1125046404PZ5-30A 4501800.191553.003.259.307.74101001 20 M1115001404PZ4-30E 180900.541553.003.259.287.72101001 20 M1125047404PZ4-30A 1801800.311553.003.259.307.74201001 20 1 20 01 17 1 17 1 17 M1125003439PZ3-30B30900.801713.002.688.747.1860561 17 61 17 1 17 41 17 1 17 01 17 M1125006417PZ2-30B6900.801803.002.408.466.90300101 17M1125033417PZ2-30B61800.361803.002.408.466.90PX Use “S” discount symbol.PZ SERIES DC LOW VOLTAGE (12V)PARALLEL SHAFT TENV 1.0 SERVICE FACTORF.L.Torque(Lb.In.)InputHP101001 20 301001 17 561 17OutputRPM55 Ratioto 7.18PZ3-3030125.61713.002.688.747.18ListPrice GearmotorType &FrameM1125213 447M1125214474M1125215474CatalogNumber Use “S” discount symbol.PZ SERIES - DC.900RefQUICK REFERENCEGEARMOTOR CROSS REFERENCE . . . . . . Page 163“L” BRACKET AND CONDUIT BOX . . . . . . . . . . . . 107SPEEDMASTER CONTROLS. . . . . . . . . . . . . . . . . 12192DIMENSIONSPCONDUIT BOX ENSIONSXLInchesXH

SUB-FHP DC GEARMOTORSPARALLEL SHAFT GEARMOTORSSCR RATED:27-353 In-Lbs TorqueLOW VOLTAGE:113-353 In-Lbs TorqueLow Voltage GearmotorsTotally enclosed, permanent magnet DC gearmotors,performance matched for continuous duty. Motors aredesigned for battery power or can be used with a lowvoltage controller with form factor up to 1.05.Mechanical Specifications:Precision machined in-line steel gears, with a firststage steel helical gear followed by spur-type gears.Lubrication is permanent semi-fluid grease, reducingpossibility of leakage. Output shafts have needlebearings for high load capacities. Shafts arehardened steel.Conduit box not included with motor. Optionalconduit box shown on page 107.Application Notes:These gearmotors are designed for mounting at anyangle, but shaft up with motor below should beavoided to prevent leakage of lubricant into the motorshould the motor’s shaft seal fail.Overhung load capacities shown are at center ofoutput shaft.The motor’s stall torque exceeds recommended fullload torques. A current limiting device such as anSCR control should be used to prevent damage.Model 300 gearmotors have the same mountingdimensions as Bison’s 300 and many Daytongearmotors.For additional information, see Bulletin 1830.PARALLEL SHAFT TENV 1.0 SERVICE FACTORF.L.Output TorqueRPM (Lb.In.)InputHPCatalogNumberGearmotorListType &Price FrameRatioto PXXLXHInches53531 20 M1115024 578P303-30E336900.545653.003.54 10.078.5792681 20 M1115025578P303-30E216900.544743.003.54 10.078.57181501 20 M1115026578P303-30E103900.543853.003.54 10.078.57201401 20M1125092593P303-31E901800.313703.113.54 10.078.572428018 M1125069593P303-30E76901.303533.003.5411.54 10.0431312202201818 00.663273273.003.003.543.5411.54 10.0411.54 10.0434821 20 M1115027578P303-30E52900.543183.003.54 10.07515113013018 1 300.662772773.003.003.543.5451551 20M1115028532P302-30E35900.542813.003.54 -31E2929901801.300.312672673.003.113.54 11.54 10.043.54 10.07 8.579494777718 00.662362363.003.003.543.5410910627261 .540.312242223.003.113.54 10.073.54 2-30E1111901801.300.661971963.003.003.543.54 1 20 18 1 20 188.5711.54 10.0411.54 10.048.5711.54 10.0411.54 10.048.578.5711.54 10.0411.54 10.04 Use “S” discount symbol.P300 SERIES DC LOW VOLTAGE (12V)PARALLEL SHAFT TENV 1.0 SERVICE FACTORF.L.Output TorqueRPM (Lb.In.)InputHPCatalogNumberListPrice GearmotorType &FrameRatioto PXXLXH8.57Inches53531 20M1125217 593P303-30336125.65653.003.8510.073122018 M1125218607P303-30581210.63273.003.5411.54 10.045113018 M1125219558P302-30351210.32773.003.2311.54 1.54 10.04 Use “S” discount symbol.P300 SERIESXHCONDUIT BOX DIMENSIONS (IN.)FRAME30/31AFXW6.26 2.63HL1.903.1393GearmotorsElectrical Specifications:SCR RatedGearmotorsTotally enclosed,permanent magnetDC gearmotors,performance matched forcontinuous duty service over a60:1 speed range. All haveconstant torque throughout the range when poweredby a full-wave unfiltered SCR-type adjustable speedcontrol having a typical form factor of 1.3 to 1.4.P300 SERIES DC SCR RATED

SUB-FHP DC GEARMOTORSOFF-SET SHAFT GEARMOTORSOS300 SERIES DC SCR RATEDOFF-SET SHAFT TENV 1.0 SERVICE FACTORF.L.Output Torque InputRPM (Lb.In.) HPElectrical Specifications:SCR Rated GearmotorsTotally enclosed, permanentmagnet DC gearmotors,performance matched forcontinuous duty service over a60:1 speed range. All have constant torquethroughout the range when powered by a full-wave unfilteredSCR-type adjustable speed control having a typical form factorof 1.3 to 1.4.Low Voltage GearmotorsTotally enclosed, permanent magnet DC gearmotors,performance matched for continuous duty. Motors are designedfor battery power or can be used with a low voltage controllerwith form factor up to 1.05.Mechanical Specifications:Precision machined steel gears, with a first stage steel helicalgear followed by spur-type gears. Lubrication is permanentsemi-fluid grease, reducing possibility of leakage. Output shaftshave needle bearings for high load capacities. Shafts arehardened steel.CatalogNumberListPrice GearmotorType &FrameRatioArmVoltsDCF.L. OverhungAmps LoadDCLbs.PDIMENSIONSXXLInchesXH2681 20M1125251 487 OS303-3021090.544743.00 2.81 4.508.52191501 20M1125250487 OS303-3010390.563853.00 2.81 4.508.522428018 M1125249500 OS303-3076901.33533.00 2.81 6.42 10.453122018 M1125248500 OS303-3058901.43273.00 2.81 6.42 10.455113018M1125247500 OS303-3035901.42773.00 2.81 6.42 10.459 OS300 SERIES DC LOW VOLTAGE (12V)OFF-SET SHAFT TENV 1.0 SERVICE FACTORF.L.Output Torque InputRPM (Lb.In.) HPCatalogNumberListPrice GearmotorType &FrameRatioArmVoltsDCF.L. OverhungAmps LoadDCLbs.PDIMENSIONSXXLInchesXH92681 20 M1125256 500 OS303-30210124.54743.00 2.81 4.508.52181501 20 M1125255500 OS303-30103125.03853.00 2.081 4.508.522428018 M1125254512 OS303-30761210.63533.00 2.81 6.42 10.453122018 M1125253512 OS303-30581210.63273.00 2.81 6.42 10.455113018M1125252512 OS303-30351210.32773.00 2.81 6.42 10.45 Use “S” discount symbol.Conduit box not included with motor. Optional conduit boxshown on page 107.Application Notes:These gearmotors are designed for mounting at any angle, butshaft up with motor below should be avoided to prevent leakageof lubricant into the motor should the motor’s shaft seal fail.Overhung load capacities shown are at center of output shaft.The motor’s stall torque exceeds recommended full loadtorques. A current limiting device such as an SCR control shouldbe used to prevent damage.OS300 SERIES3.94 REF"XL" REF3.375 TYP.187 SQx 1.00 LONGKEY1.6881.501.312.81 REF"XH"1.581.00FULLDEPTH3.13 REF.675CONDUIT BOX(OPTIONAL)(3) LEADS12.0 LONG MIN1.79 REF.517.625Ø.6243.375 TYP6.11 REF1.25TO SHAFTSHOULDERTOP(4) 5/16-18 UNC-2B.62 DP MIN1.65Ø3.00GearmotorsSCR RATED:130-268 In-Lbs TorqueLOW VOLTAGE:130-268 In-Lbs Torque.11 REF3.30NAMEPLATELOCKSEAM(FAR SIDE)LOAD SPRINGAT THIS ENDALL DIMENSIONS IN INCHES94

SUB-FHP DC GEARMOTORSPARALLEL SHAFT GEARMOTORSSCR RATED:25-371 In-Lbs TorqueLOW VOLTAGE:155-341 In-Lbs TorqueLow Voltage GearmotorsTotally enclosed, permanent magnet DC gearmotors,performance matched for continuous duty. Motors aredesigned for battery power or can be used with a lowvoltage controller with form factor up to 1.05.Mechanical Specifications:Gearbox has rugged aluminum die cast housing, formaximum gear and bearing support. Precision machinedgearing, hardened for maximum load capability. Allgearing designed and rated to AGMA Class 9 standardsand to withstand momentary shock overload of 200%.Oversized output bearings for greater overhung loadcapacity and longer life. High-carbon alloy output shaftprovides maximum strength and rigidity. All needlebearing journals are precision-ground after heat treating,to provide maximum finish and fit. Heavy-duty industrialoil seals help keep lubricant in and dirt out. Gears andbearings are splash lubricated with permanent, heavyduty gear oil.Conduit box not included with motor. Optional conduitbox shown on page 107.Application Notes:These gearmotors are designed for mounting at anyangle, but shaft up with motor below should be avoided toprevent leakage of lubricant into the motor should themotor’s shaft seal fail.Overhung load capacities shown are at center of outputshaft.The motor’s stall torque exceeds recommended full loadtorques. A current limiting device such as an SCR controlshould be used to prevent damage.Model PE350 gearmotors have the same mountingdimensions as Bodine’s “E” box and many Baldorgearmotors.PARALLEL SHAFT TENV 1.0 SERVICE FACTOROutputRPMF.L.Torque(Lb.In.)Ratioto 1ArmVoltsDCF.L. OverhungAmpsLoadDCLbs.77 585585P353-34 336P353-34 135140585585P353-34 180P353-34 180901801.000.5046546511.3111.319.319.31 M1135117M1135141612612P353-34 124P353-34 124901801.100.5541341313.3113.3111.3111.3130530514 .7537437413.3113.3111.3111.31424228028014 .2032732713.3113.3111.3111.31505025025014 .2031531513.3113.3111.3111.31626222022014 .2030330313.3113.3111.3111.31838315515514 .2026726713.3113.3111.3111.3112512510010014 .0025625613.3113.3111.3111.31165165707014 .0023223213.3113.3111.3111.31250250454514 .3113.3111.3111.31InputHPCatalogNumberListPrice 33033018 M1135106M1135139141434134118 21213713711427271818141414141414141414 14Type &FrameDIMENSIONSXLXHInchesGearmotorsElectrical Specifications:SCR Rated GearmotorsTotally enclosed, permanentmagnet DC gearmotors,performance matched forcontinuous duty service overa 60:1 speed range. All haveconstant torque throughout therange when powered by a full-waveunfiltered SCR-type adjustable speed controlhaving a typical form factor of 1.3 to 1.4.PE350 SERIES DC SCR RATED Use “S” discount symbol for all gearmotors.PE350 SERIES DC LOW VOLTAGE (12V)PARALLEL SHAFT TENV 1.0 SERVICE berListPrice 1434118 M1135243 597P353-34 180128.746511.059.054232514 M1135244625P353-34581221.032713.3111.316222014 5246593P352-34291221.026713.3111.31 Type &FrameRatioto 1ArmVoltsDCF.L. OverhungAmpsLoadDCLbs.DIMENSIONSXLXHInches Use “S” discount symbol for all gearmotors.PE350 SERIES - DCALL DIMENSIONS IN INCHES95

SUB-FHP DC GEARMOTORSPARALLEL SHAFT GEARMOTORSSCR RATED:105-1112 In-Lbs TorqueLOW VOLTAGE:320-1087 In-Lbs TorqueGearmotorsElectrical Specifications:SCR Rated GearmotorsSCR rated, permanent magnetDC gearmotors. Totallyenclosed for continuous duty,general purpose applications. Allhave constant torque throughout the60:1 speed range, when powered by afull-wave, unfiltered SCR-type adjustablespeed control having a typical form factor of1.3 to 1.4.Low Voltage GearmotorsTotally enclosed, permanent magnet DC gearmotors,performance matched for continuous duty. Motors aredesigned for battery power or can be used with a low voltagecontroller with form factor up to 1.05.Mechanical Specifications:Gearbox has rugged aluminum die cast housing, formaximum gear and bearing support. Precision machinedgearing, hardened for maximum load capability. All gearingdesigned and rated to AGMA Class 9 standards and towithstand momentary shock overload of 200%. Oversizedoutput bearings for greater overhung load capacity and longerlife. High-carbon alloy output shaft provides maximumstrength and rigidity. All needle bearing journals are precisionground after heat treating, to provide maximum finish and fit.Heavy-duty industrial oil seals help keep lubricant in and dirtout. Gears and bearings are splash lubricated withpermanent, heavy-duty gear oil. Conduit box is included asstandard.Application Notes:These gearmotors are designed for mounting at any angle,but shaft-up with motor below gearhead is not recommended.Overhung load capacities shown are at center of output shaft.P1100 DC gearmotors have the same mounting dimensionsas Bison 483 gearmotors and many Dayton gearmotors.The motor’s stall torque exceeds recommended full loadtorques. A current limiting device such as an SCR controlshould be used to prevent damage.For additional information, see Bulletin 1830.P1100 SERIES DC SCR RATEDFRACTIONAL HP PARALLEL SHAFT TOTALLY ENCLOSED1.0 SERVICE berListPrice Type &FrameRatioto 1ArmVoltsDCDIMENSIONSXLXHInches8108714 108700 996P1103-48212902.770014.24 12.7412103014 108701996P1103-48143902.770014.24 12.741875014 108702996P1103-4895902.770014.24 12.744235314 108703972P1102-4842902.765014.24 12.746023814 108704972P1102-4829902.762514.24 12.749216014 108705972P1102-4819902.757514.24 12.7413510514108706972P1102-4813902.752514.24 12.7418111212 108707**1078P1103-4895905.070016.49 14.993382212 108708**1078P1103-4853905.065016.49 14.994270512 108709**1056P1102-4842905.065016.49 14.996047612 108710**1056P1102-4829905.062516.49 14.999232012 108711**1056P1102-4819905.057516.49 14.9913521012108712**1056P1102-4813905.052516.49 14.99 Use “S” discount symbol.** TEFC enclosure.P1100 SERIES DC LOW VOLTAGE (12V)FRACTIONAL HP PARALLEL SHAFT TOTALLY ENCLOSED1.0 SERVICE FACTOROutputRPMF.L.Torque(Lb.In.)InputHP8108714 10872960238141087304270512 9232012 Type &FrameRatioto 1ArmVoltsDC 4 12.24108731**1078P1102-48421240.065015.99 14.49108732**1078P1102-48191240.057515.99 14.49CatalogNumberListPrice Use “S” discount symbol.** TEFC enclosure.P1100 SERIES - DCALL DIMENSIONS IN INCHES96F.L. OverhungAmps LoadDC(Lbs.)F.L. OverhungAmps LoadDC(Lbs.)DIMENSIONSXLXHInches13.74 12.24

SUB-FHP DC GEARMOTORSRIGHT ANGLE GEARMOTORSSCR RATED:5-135 In-Lbs TorqueLOW VOLTAGE:25-135 In-Lbs TorqueLow Voltage GearmotorsTotally enclosed, permanent magnet DC gearmotors,performance matched for continuous duty. Motors aredesigned for battery power or can be used with a lowvoltage controller with form factor up to 1.05.Mechanical Specifications:This worm-type right-angle gearing features hardened,steel worm with bronze worm wheel for long life andquiet operation. Precision machined aluminum housingsare used. Gearbox has all ball bearings. The housing issealed and lubrication is permanent with an oil bath. Theoutput shaft is field interchangeable from left hand styleto right hand style by reassembly.Application Notes:For optimum seal life, theseright-angle gearmotors havea lubrication breatherpositioned for horizontalmounting. For othermountings, the breatherplug must be reoriented byusing a 901/8" NPT taper pipeelbow (see drawing). Elbow notavailable from LEESON. Vent plug is available (Part#M1900177 01). However, the motor portion of thegearmotor should never be mounted below thegearhead.Overhung load capacities shown are at center of outputshaft. Conduit box not supplied with motor. See page103 for optional conduit box and optional base kit.See page 163 for cross reference data betweenLEESON and other gearmotors.For additional information on LEESON gearmotors, seeBulletin 1830.TENV 1.0 SERVICE FACTOROutputRPMF.L.Torque Input(In.-Lbs.) HPCatalogNumberListPrice GearmotorType &FrameRatioto 1FullArm LoadVolts H42221 17M1115018 453 10F60-25D 60901.001852.50 3.00 3.608.79 5.1962191 17 M1115019453 10F40-25D 40901.001852.50 3.00 3.608.79 5.19125161 17 M1115020453 10F20-25D 20901.001852.50 3.00 3.608.79 5.19250101 17 M1115021453 10F10-25D 10901.001852.50 3.00 3.608.79 5.1950051 17 M1115022453 10F05-25D 5901.001852.50 3.00 3.608.79 5.1942301 12 M1135053453 13F60-34A 60180 0.532353.38 4.00 4.509.64 5.1462351 12 M1135054453 13F40-34A 40180 0.532353.38 4.00 4.509.64 5.14125181 12 M1135055453 13F20-34A 20180 0.532353.38 4.00 4.509.64 5.14250101 12 M1135056453 13F10-34A 10180 0.532353.38 4.00 4.509.64 5.1450051 12M1135057453 13F05-34A180 0.532353.38 4.00 4.509.64 5.14428018 M1135069522 13F60-34C 60901.402353.38 4.00 4.50 10.64 6.146262707018 1 8M1135038M1135058522 13F40-34C 40522 13F40-34C 4090 1.40180 0.702352353.38 4.00 4.50 10.64 6.143.38 4.00 4.50 10.64 6.14125125454518 M1135039M1135059522 13F20-34C 20522 13F20-34C 2090 1.40180 0.702352353.38 4.00 4.50 10.64 6.143.38 4.00 4.50 10.64 6.14250250252518 M1135040M1135060522 13F10-34C 10522 13F10-34C 1090 1.40180 0.702352353.38 4.00 4.50 10.64 6.143.38 4.00 4.50 10.64 6.14500500131318 M1135041M1135061522 13F05-34C 5522 13F05-34C 590 1.40180 0.702352353.38 4.00 4.50 10.64 6.143.38 4.00 4.50 10.64 6.14626213513514 M1135042M1135062562 13F40-34G 40562 13F40-34G 4090 2.30180 1.302352353.38 4.00 4.50 12.64 8.143.38 4.00 4.50 12.64 8.14838312512514 M1135043M1135063562 13F30-34G 30562 13F30-34G 3090 2.30180 1.302352353.38 4.00 4.50 12.64 8.143.38 4.00 4.50 12.64 8.14125125909014 M1135044M1135064562 13F20-34G 20562 13F20-34G 2090 2.30180 1.302352353.38 4.00 4.50 12.64 8.143.38 4.00 4.50 12.64 8.14250250505014 M1135045M1135065562 13F10-34G 10562 13F10-34G 1090 2.30180 1.302352353.38 4.00 4.50 12.64 8.143.38 4.00 4.50 12.64 8.14500500303014M1135046M1135066562 13F05-34G 5562 13F05-34G 590 2.30180 1.302352353.38 4.00 4.50 12.64 8.143.38 4.00 4.50 12.64 8.14 18181814141414 145 Use “S” discount symbol.RIGHT-ANGLE DC LOW VOLTAGE (12V)TENV 1.0 SERVICE FACTOROutputRPMF.L.Torque Input(In.-Lbs.) HPCatalogNumberListPrice GearmotorType &FrameFullArm LoadRatio Volts Amps.to 018M1135249 53213F60-34601211.02352502518 M113525053213F10-34101211.02353.38 4.21 4.50 10.39 5.896213514 M113525157013F40-34401221.02353.38 4.21 4.50 12.64 8.141259014M113525257013F20-34201221.02353.38 4.21 4.50 12.64 8.14 3.38 4.21 4.50 10.39 5.89 Use “S” discount symbol.10 SERIES - DC13 SERIES - DC97GearmotorsElectrical Specifications:SCR Rated GearmotorsTotally enclosed right-anglegearmotors, performancematched for continuousservice over a 60:1 speedrange. All have constant torquethroughout the range when powered by afull-wave, unfiltered SCR-type 115 volt input adjustablespeed control having a typical form factor of 1.3 to 1.4.Also available as factory options are motors for lowvoltage input and with double output shafts.RIGHT-ANGLE DC SCR RATED

SERIES 12 SUB-FHPRIGHT ANGLE DC GEARMOTORSSERIES 12 SUB-FHPRIGHT-ANGLE DC SCR 90 VOLT RATEDTEFC 1.0 SERVICE FACTORGearmotorsElectrical Specifications:Both SCR (90 volt)and Low Voltage(12 volt) right anglegearmotors. the 90volt motors areperformancematched forcontinuous serviceover a 60:1 speedrange. All have constanttorque throughout the speed range when powered by a full-wave,unfiltered SCR-type 115 volt input adjustable speed control having atypical form factor of 1.3 to 1.4. The low voltage motors are alsoperformance matched for continuous duty. Motors are designed forbattery power or can be used with a low voltage controller with formfactor up to 1.05.F.L.Input TorqueHP (In.-Lbs.)OutputRPMCatalogNumberListPrice FullArmVoltsDCLoadAmps.DC1/8*12528M1135292 G7902.6Ratioto 1ArmVoltsDCFullLoadAmps.DC14RIGHT-ANGLE DC LOW VOLTAGE (12V)TENV 1.0 SERVICE FACTORThis worm-type right-anglegearing featureshardened, steel worm withbronze worm wheel forlong life and quietoperation. Single-piece diecast aluminum alloyhousing is vacuumimpregnated with ResinolRT for protection and sealing.This gearbox combines lightweight with high tensile strength along with being precision machinedfor alignment of bearings and gearing. For optimum seal life, we usehigh-temperature Nitrile seals. Gearbox provided with solid outputshaft, but can be converted to a hollow output shaft mounting byusing snap-ring pliers and remove the snap ring and solid outputshaft. Also the T-base feet are bolted to the gearbox, but can easilybe removed and converted to face mounting.F.L.Input TorqueHP (In.-Lbs.)EnclosureGearmotorType &Frame1/813427M1135285 putRPMCatalogNumberListPrice Use “S” discount symbol.NOTES:1. Conduit box not supplied with the gearmotor. Mounting provisions are provided and can use conduitbox kit catalog number M1760007 found on page 107.2. For solid double output shaft, consult factory.Conduit box not supplied with motor. See page 107.98Ratioto 1* Supplied with TENV motor enclosure Use “S” discount symbol.Mechanical Specifications:SCR 90 VOLT RATEDDIMENSIONS (INCHES)EnclosureGearmotorType &FrameLOW VOLTAGE (12V)DIMENSIONS 211.827.54.21

IP55 WASHGUARD GEARMOTORSPARALLEL SHAFTGeneral Specifications:DC permanent magnetgearmotors rated forcontinuous duty.Designed for use withfullwave non-filteredSCR controls or batterysupplied low voltage foradjustable speedapplications requiring constanttorque throughout the speed range.P300 SERIES SCR RATED 90VPARALLEL SHAFT TENV 1.0 SERVICE FACTORCatalogNumberListPrice GearmotorType &FrameRatioto 1Arm.VoltsDCFullLoadAmpsDCOverhungLoad(Lbs.)1 20M1125261 672P303-3133690.815653.13 3.80 3.54 10.4422018 M1125262690P303-3158901.63273.13 3.80 3.54 11.94 10.445113018 M1125263638P302-3135901.62773.13 3.80 3.54 11.94 10.44947718 M1125264638P302-3119901.62363.13 3.80 3.54 11.94 10.441674318M1125265638P302-3111901.61973.13 3.80 3.54 11.94 10.44F.L.Torque(Lb.In.)InputHP535331OutputRPM PBXInchesXLXH8.94 Use “S” discount symbol.Frame, endshields, armature and interiorcomponents protected by enamel and polyestercompounds for resistance to moisture, acids, alkaliesand oil.P300 SERIES LOW VOLTAGE (12V)PARALLEL SHAFT TENV 1.0 SERVICE FACTORCast conduit box with threaded conduit holes andNitrile gaskets keep water out. The conduit box coveris made from 304 stainless or any condensation that may accumulate insidethe motor, a one-way stainless steel vapor vent isprovided. All hardware is stainless steel. Motorpainted with white epoxy for superior corrosionresistance and protection. Machined fits between theendbells and motor frame are sealed with gaskets.Thru-bolt heads and nuts sealed with fiber washers.O-rings under each threaded brush tPrice 1 20M1125266 690P303-31336126.45653.13 3.80 3.54 10.448.9418M1125267707P303-31581211.03273.13 4.43 3.54 11.449.94 Ratioto 1Arm.VoltsDCFullLoadAmpsDCGearmotorType &FramePPBXInchesXLXH Use “S” discount symbol.Precision machined in-line steel gears, with a firststage steel helical gear followed by spur-type gears.Lubrication is permanent semi-fluid grease, reducingpossibility of leakage. Output shafts have needlebearings for high load capacities.Application Notes:LEESON WASHGUARD motors are designed forextended life in applications requiring regularwashdown or otherwise wet environments.Washguard motors retard the entrance of water.Extra protection for the motor’s interior prevents rustand corrosion build-up and releases trappedmoisture to insure a longer life than possible with astandard motor.These gearmotors are designed for mounting at anyangle, but shaft up with motor below should beavoided to prevent leakage of lubricant into the motorshould the shaft seal fail.Overhung load capacities shown are at center of theoutput shaft.The motor’s stall torque exceeds recommended fullload torques for the gearboxes. A current limitingdevice should be used to prevent damage to thegear sets.4.08 REF"BD" REF3.375 REF"XL" REF3.60 REF3.00 REF"XH"1.501.688"X"1.501.656.175.187 SQ KEY1.00 LONGØ1.40REF(4) Ø.2901/2 NPTCONDUITPLUG1.86 REF.662.94 REF3.75 REFMOTOR LEADS6.0 LONG MIN6.35"P"Ø.625 .6244.755.123.0003.503.125 .010.6723.375TOPIMMERSION PROOFBREATHER1.4501.1252.2501.5002.004.00(8) Ø.230 X .44 DP(3) 1/4-20 UNC-2B.50 DP.281TYP4.96 REF99GearmotorsMechanical Specifications:Gearbox output shafts are coated with Mirolon 3300fortified Teflon for superior corrosion resistance. DIMENSIONSP

IP55 WASHGUARD GEARMOTORSPARALLEL SHAFTPE350 SERIES PARALLEL SHAFTTENV 1.0 SERVICE FACTOR SCR RATED 90VDC permanentmagnet gearmotorsrated for continuousduty. Designed foruse with fullwavenon-filtered SCRcontrols or batterysupplied low voltagefor adjustable speedapplications requiringconstant torque throughoutthe speed range.F.L.Output Torque

SUB-FHP DC GEARMOTORS PARALLEL SHAFT GEARMOTORS PZ SERIES DC SCR RATED PARALLEL SHAFT TENV 1.0 SERVICE FACTOR Over-DIMENSIONS F.L. Gearmotor Arm. F.L. hung Output Torque Input Catalog List Type & Ratio Volts Amps Load P X XL XH RPM (Lb.In.) HP Number Price Frame to 1 DC DC (Lb.) Inches 4401 40

Related Documents:

Quick Reference -Stock Sub-FHP Gearmotors P240 &P300 Series Gearmotors PE350 Series Gearmotors OS300 Series Gearmotors Single Phase 115/230V 43-391 In-Lbs Output Torque Page 342 DC SCR 90 &180V 27-353 In-Lbs Output Torque Low Voltage (12V) 113-353 In-Lbs torque Page 322 Single Phase 115/230V 25-341 In-Lbs Output Torque

Frontiers in Heat Pipes (FHP), 1, 023003 (2010) DOI: 10.5098/fhp.v1.2.3003 Global Digital Central ISSN: 2155-658X 1 LOCAL HYDRODYNAMICS OF FLOW IN A PULSATING HEAT PIPE: . The bubbles act as pumping elements, transporting the entrapped liquid slugs in a complex oscillating-translating-vibratory

Slicing Steaks 3563 Beef Tender, Select In Stock 3852 Angus XT Shoulder Clod, Choice In Stock 3853 Angus XT Chuck Roll, Choice 20/up In Stock 3856 Angus XT Peeled Knuckle In Stock 3857 Angus XT Inside Rounds In Stock 3858 Angus XT Flats, Choice In Stock 3859 Angus XT Eye Of Round, Choice In Stock 3507 Point Off Bnls Beef Brisket, Choice In Stock

First-Year Honors Program (FHP) on behalf of the entire Honors community here at Iowa State! FHP is an excellent way to meet some amazing individuals, connect with the outstanding upper-division Honors students who lead the introductory seminars, make lasting friendships,

This phenomenon is known as the Feldstein-Horioka Puzzle (FHP). In the literature a great deal of attention has been given to the FHP (see, for example, literature surveys by Frankel [1992], Coakley et al.[1998], and Apergis and Tsoumas [2009]). In looking for support or for contradictor

Heat pump size range categories: ½ - 5 tons, 6-10 tons, 7-25 tons Piping material. 9 . McQuay International (www.mcquay.com) FHP Manufacturing (www.fhp-mfg.com) Warranty Info . Generally 25 years for the inside components and 50 years for the ground loop. Code Restrictions .

way. One of these models is the Functional Health Patterns (FHP) model. The FHP model, which is a nursing care model that evaluates individuals in a holistic way, was developed by the nursing theoretician Marjory Gordon in 1982.14 This model examines the needs of an individual under 11 functional areas that are related to each

2 Page . Preface . The Academic Phrasebank is a general resource for academic writers. It aims to provide the phraseological ‘nuts and bolts’ of academic writing organised a