LEESON Sub-FHP Gear Motors

2y ago
17 Views
3 Downloads
1.09 MB
24 Pages
Last View : 3d ago
Last Download : 5m ago
Upload by : Karl Gosselin
Transcription

IEC MotorsDC MotorsGearmotorsAC / DC ControlsAccessories / KitsMods / FactoryOptionsX-Ref / IndexTech InformationTerms / WarningsGearmotorsQuick Reference – Stock Sub-FHP GearmotorsAC Single & Three PhaseParallel ShaftPZ SeriesGearmotorsP240 & P300 SeriesGearmotorsDC SCR & Low VoltageSingle Phase 115V12-100 In-LbsOutput TorquePage 340DC SCR 90 & 180V10-100 In-LbsOutput TorqueLow Voltage (12V)36-100 In-Lbs torquePage 320Single Phase 115/230V43-391 In-LbsOutput TorquePage 342DC SCR 90 & 180V27-353 In-LbsOutput TorqueLow Voltage (12V)113-353 In-Lbs torquePage 322DC SCR 90VandLow Voltage (12V)Output Torque130-268 In-LbsPage 324OS300 SeriesGearmotorsPE350 SeriesGearmotorsSingle Phase 115/230V25-341 In-LbsOutput TorqueThree Phase 230/460V55-320 In-LbsOutput TorquePage 344DC SCR 90 & 180V25-371 In-LbsOutput TorqueLow Voltage (12V)155-341 In-Lbs torquePage 326P1100 SeriesGearmotorsSingle Phase 115/230V70-1105 In-LbsOutput TorqueThree Phase 230/460V70-1105 In-LbsOutput TorquePage 346DC SCR 90V105-1112 In-LbsOutput TorqueLow Voltage (12V)320-1087 In-Lbs torquePage 328Single Phase 115/230V14-113 In-LbsOutput TorquePage 348DC SCR 90 & 180V5-135 In-LbsOutput TorqueLow Voltage (12V)25-135 In-Lbs torquePage 330Right-AngleWorm Type10 & 13 SeriesGearmotorsBravo Right AngleWorm Type12 SeriesGearmotorsDC SCR 90VandLow Voltage (12V)Output Torque46-134 In-LbsPage 332Buy: www.ValinOnline.com Phone 844-385-3099 Email: CustomerService@valin.com

Parallel Shaft - PZ Series - DCSCR Rated - 10-100 In-Lbs TorqueLow Voltage - 36-100 In-Lbs TorqueGeneral Specifications - SCR Rated Gearmotors: Performance matched for continuous duty service over 60:1 speed range Constant torque throughout the range when powered by a full-wave unfiltered SCR-type adjustablespeed control having a typical form factor of 1.3 to 1.4General Specifications - Low Voltage Gearmotors: Performance matched for continuous duty service Designed for battery power or can be used with a low voltage controller with form factor up to 1.05Features: Precision machined in-line steel gears First stage steel helical gear followed by spur-type gears Lubrication is permanent semi-fluid grease, reducing possibility of leakage Output shafts have needle bearings for high load capacities Shafts are hardened steel Optional conduit box and PZ gearmotor mounting bracket available, see page 342Application Notes: These gearmotors are designed for mounting at any angle, but motor below the reducer should beavoided to prevent leakage of lubricant into the motor should the motor shaft seal fail Motor’s stall torque could exceed recommended full load torques. A current limiting device such asan SCR control should be used to prevent damage. This issue is even more critical for low voltagemotors, typically no controller is used since motor is connected directly to a battery, so some type ofcurrent limit or fusing should be considered Overhung load capacities shown are at center of output shaft Model PZ gearmotors have the same mounting dimensions as Bodine model D and Z, Baldor/Boehm, Bison 100 gearmotors, and a number of Dayton gearmotors For additional information, see Bulletin 1830 Bodine/Baldor/Boehm/Bison/Dayton direct interchangeTerms / WarningsTech InformationX-Ref / IndexMods / FactoryOptionsAccessories / KitsAC / DC ControlsGearmotorsDC MotorsIEC MotorsGearmotorsBuy: www.ValinOnline.com Phone 844-385-3099 Email: CustomerService@valin.com

Parallel Shaft - PZ Series - DCSCR Rated - 10-100 In-Lbs TorqueLow Voltage - 36-100 In-Lbs TorqueCatalogNumberStockF.L.Output Torque InputRPM (Lb.In.) HPOverGearmotorArm. F.L. hungList ModelType & Ratio Volts Amps LoadPrice Number Frameto 1DCDC(lb.)DC Motors90 & 180 Volts - TENV - PZ SeriesDimensions (inches) 527 985.620PZ5-30A450900.51553.003.259.287.72 S, US401 40 M1125046.00 527 985.623PZ5-30A4501800.21553.003.259.307.74 S, US101001 20 M1115001.00 527 985.621PZ4-30E180900.51553.003.259.287.72 S, US1001 20 M1125047.00C/A527 985.624PZ4-30A1801800.31553.003.259.307.74 S, US1001 20 M1115000.00 527 985.622PZ4-30E90900.51553.003.259.287.72 S, US1001 20 M1125048.00C/A527 985.625PZ4-30A901800.31553.003.259.307.74 S, US1001 17 M1125002.00 573 985.627PZ3-30B60900.81553.002.688.747.18 S, US1001 17 M1125037.00 573 985.635PZ3-30B601800.41553.002.688.747.18 S, US561 17 M1125003.00 573 985.628PZ3-30B30900.81713.002.688.747.18 S, US561 17 M1125036.00 573 985.634PZ3-30B301800.41713.002.688.747.18 S, US361 17 M1125004.00 573 985.626PZ3-30B18900.81713.002.688.747.18 S, US361 17 M1125035.00 573 985.631PZ3-30B181800.41713.002.688.747.18 S, US241 17 M1125005.00 544 985.629PZ2-30B12900.81803.002.408.466.90 S, US241 17 M1125034.00 544 985.633PZ2-30B121800.41803.002.408.466.90 S, US101 17 M1125006.00 544 985.630PZ2-30B6900.81803.002.408.466.90 S, US101 17 M1125033.00 544 985.632PZ2-30B61800.41803.002.408.466.90 S, US3060100150300C/A - Check AvailabilitySpecifications are subject to change without noticeXHYNotesY Note listing on inside back flapCatalogNumberOverGearmotorArm. F.L. hungList ModelType & Ratio Volts Amps LoadPrice Number Frameto 1DCDC(lb.)Dimensions (inches)PXXL101001 20 M1125213.00 583 985.653PZ4-30180122.71553.003.259.287.72 S, US301001 17 M1125214.00 619 985.654PZ3-3060125.21553.002.688.747.18 S, US55561 17 M1125215.00 619 985.655PZ3-3030125.61713.002.688.747.18 S, USSpecifications are subject to change without noticeXHYNotesMods / FactoryOptionsF.L.Output Torque InputRPM (Lb.In.) HPStock12 Volts - TENV - PZ SeriesAccessories / KitsXL1 40 M1115002.00AC / DC ControlsX40GearmotorsP420IEC MotorsGearmotorsY Note listing on inside back flapFrameXWABHL30/312.633.471.903.13X-Ref / IndexConduit Box Dimensions (IN)PZ SERIES - DCTech Information.900RefBuy: www.ValinOnline.com Phone 844-385-3099 Email: CustomerService@valin.comTerms / WarningsView On-line Technical Information

Parallel Shaft - P300 Series - DCSCR Rated - 27-353 In-Lbs . TorqueLow Voltage - 113-353 In-Lbs TorqueGeneral Specifications - SCR Rated Gearmotors: Performance matched for continuous duty service over 60:1 speed range Constant torque throughout the range when powered by a full-wave unfiltered SCR-type adjustablespeed control having a typical form factor of 1.3 to 1.4General Specifications - Low Voltage Gearmotors: Performance matched for continuous duty service Designed for battery power or can be used with a low voltage controller with form factor up to 1.05Features: Precision machined in-line steel gears First stage steel helical gear followed by spur-type gears Lubrication is permanent semi-fluid grease, reducing possibility of leakage Output shafts have needle bearings for high load capacities Shafts are hardened steel Optional conduit box available, see page 350Application Notes: These gearmotors are designed for mounting at any angle, but motor below the reducer should beavoided to prevent leakage of lubricant into the motor should the motor shaft seal fail Motor’s stall torque could exceed recommended full load torques. A current limiting device such asan SCR control should be used to prevent damage. This issue is even more critical for low voltagemotors, typically no controller is used since motor is connected directly to a battery, so some type ofcurrent limit or fusing should be considered Overhung load capacities shown are at center of output shaft For additional information, see Bulletin 1830 Bison/Dayton direct interchangeTerms / WarningsTech InformationX-Ref / IndexMods / FactoryOptionsAccessories / KitsAC / DC ControlsGearmotorsDC MotorsIEC MotorsGearmotorsBuy: www.ValinOnline.com Phone 844-385-3099 Email: CustomerService@valin.com

Parallel Shaft - P300 Series - DCSCR Rated - 27-353 In-Lbs . TorqueLow Voltage - 113-353 In-Lbs 4.00M1125041.00 C/A .5710.0410.048.578.5710.0410.04C/A - Check AvailabilitySpecifications are subject to change without noticeYNotesS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USY Note listing on inside back flapCatalogNumberOverGearmotorArm. F.L. hungList ModelType & Ratio Volts Amps LoadPrice Number Frameto 1DCDC(lb.)Dimensions (inches)PXXL53531 20 M1125217.00 774 985.657P303-30336125.65653.003.8510.078.57 S, US312201 8M1125218.00 793 985.658P303-30581210.63273.003.5411.5410.04 S, US511301 8M1125219.00 729 985.659P302-30351210.32773.003.2311.5410.04 S, US611131 8M1125220.00 729 985.660P302-30291210.42673.003.2311.5410.04 S, USYNotesY Note listing on inside back flapConduit Box Dimensions (IN .)P300 SERIESXFrameAFXWHL30/316.262.631.903.13X-Ref / IndexSpecifications are subject to change without noticeXHMods / FactoryOptionsF.L.Output Torque InputRPM (Lb.In.) HPStock12 Volt - TENV - P300 SeriesAccessories / Kits1 201 201 201 201 81 81 81 201 81 81 201 81 201 81 81 201 201 81 8Dimensions (inches)AC / DC 264343OverGearmotorArm. F.L. hungList ModelType & Ratio Volts Amps LoadPrice Number Frameto 9106167170CatalogNumberStockF.L.Output Torque InputRPM (Lb.In.) HPDC Motors90 & 180 Volts - TENV - P300 SeriesIEC MotorsGearmotorsTech InformationHBuy: www.ValinOnline.com Phone 844-385-3099 Email: CustomerService@valin.comTerms / WarningsView On-line Technical Information

Off-Set Shaft Gearmotors - OS300 Series - DCSCR Rated - 130-268 In-Lbs. TorqueLow Voltage - 130-268 In-Lbs. TorqueGeneral Specifications - SCR Rated Gearmotors: Performance matched for continuous duty service over 60:1 speed range Constant torque throughout the range when powered by a full-wave unfiltered SCR-type adjustablespeed control having a typical form factor of 1.3 to 1.4General Specifications - Low Voltage Gearmotors: Performance matched for continuous duty service Designed for battery power or can be used with a low voltage controller with form factor up to 1.05Features: Precision machined in-line steel gears First stage steel helical gear followed by spur-type gears Lubrication is permanent semi-fluid grease, reducing possibility of leakage Output shafts have needle bearings for high load capacities Shafts are hardened steel Optional conduit box available, see page 350Application Notes: These gearmotors are designed for mounting at any angle, but motor below the reducer should beavoided to prevent leakage of lubricant into the motor should the motor shaft seal fail Motor’s stall torque could exceed recommended full load torques. A current limiting device such asan SCR control should be used to prevent damage. This issue is even more critical for low voltagemotors, typically no controller is used since motor is connected directly to a battery, so some type ofcurrent limit or fusing should be considered Overhung load capacities shown are at center of output shaftTerms / WarningsTech InformationX-Ref / IndexMods / FactoryOptionsAccessories / KitsAC / DC ControlsGearmotorsDC MotorsIEC MotorsGearmotorsBuy: www.ValinOnline.com Phone 844-385-3099 Email: CustomerService@valin.com

Off-Set Shaft Gearmotors - OS300 Series - DCSCR Rated - 130-268 In-Lbs. TorqueLow Voltage - 130-268 In-Lbs. TorqueCatalogNumberStockF.L.Output Torque InputRPM (Lb.In.) HPOverGearmotorArm. F.L. hungList ModelType & Ratio Volts Amps LoadPrice Number Frameto 1DCDC(lb.)DC Motors90 Volts - TENV - OS300 SeriesDimensions (inches)XXLXH2681 20 M1125251.00C/A637 985.692OS303-30210900.54743.002.814.58.52 S, USYNotes191501 20 M1125250.00 637 985.691OS303-30103900.63853.002.814.58.52 S, US242801 8M1125249.00 653 985.690OS303-3076901.33533.002.816.4210.45 S, US312201 8M1125248.00 653 985.689OS303-3058901.43273.002.816.4210.45 S, US511301 8M1125247.00 653 985.688OS303-3035901.42773.002.816.4210.45 S, USY Note listing on inside back flapCatalogNumberStockF.L.Output Torque InputRPM (Lb.In.) HP2681 20 M1125256.00C/A181501 20 M1125255.00C/A242801 8M1125254.00 312201 8M1125253.00 511301 8M1125252.00 653 985.697124.5474Dimensions (inches)PXXLXH3.002.814.58.52 S, USYNotesOS303-30210653 985.696OS303-30103125.03853.002.084.58.52 S, US669 985.695OS303-30761210.63533.002.816.4210.45 S, US669 985.694OS303-30581210.63273.002.816.4210.45 S, US669 985.693OS303-30351210.32773.002.816.4210.45 S, USY Note listing on inside back flapC/A - Check AvailabilitySpecifications are subject to change without noticeMods / FactoryOptionsOS300 SERIES3.94 REF"XL" REF3.375 TYP.187 SQx 1.00 LONGKEY1.6881.501.312.81 REF"XH"3.13 REF(3) LEADS12.0 LONG MIN1.79 REF.625Ø.6243.375 TYP.517CONDUIT BOX(OPTIONAL)1.25TO SHAFTSHOULDERTOP.11 REF3.30NAMEPLATELOCKSEAM(FAR SIDE)LOAD SPRINGAT THIS ENDALL DIMENSIONS IN INCHESBuy: www.ValinOnline.com Phone 844-385-3099 Email: CustomerService@valin.comTerms / WarningsView On-line Technical InformationTech Information1.65Ø3.00(4) 5/16-18 UNC-2B.62 DP MINX-Ref / Index6.11 REF.6751.581.00FULLDEPTHAccessories / Kits9OverGearmotorArm. F.L. hungList ModelType & Ratio Volts Amps LoadPrice Number Frameto 1DCDC(lb.)AC / DC Controls12 Volts - TENV - OS300 SeriesGearmotorsP9C/A - Check AvailabilitySpecifications are subject to change without noticeIEC MotorsGearmotors

PE350 Series - Parallel Shaft - DCSCR Rated - 25-371 In-Lbs . TorqueLow Voltage - 155-341 In-Lbs TorqueGeneral Specifications - SCR Rated Gearmotors: Performance matched for continuous duty service over 60:1 speed range Constant torque throughout the range when powered by a full-wave unfiltered SCR-type adjustablespeed control having a typical form factor of 1.3 to 1.4General Specifications - Low Voltage Gearmotors: Performance matched for continuous duty service Designed for battery power or can be used with a low voltage controller with form factor up to 1.05Features: Rugged die cast aluminum gear housing for maximum gear and bearing support Precision machined gearing, hardened for maximum load capability All gearing designed and rated to AGMA class 9 standards, and to withstand momentary shockoverload of 200% Oversized output bearings for greater overhung load capacity and long life High carbon alloy output shaft provides maximum strength and rigidity All needle bearing journals are precision ground after heat treating to provide maximumfit and finish Heavy duty industrial oil seals keep lubricant in and dirt out Gears and bearings are splash lubricated with permanent, heavy duty gear oil Optional conduit box available, see page 350Application Notes: These gearmotors are designed for mounting at any angle, but motor below the reducer should beavoided to prevent leakage of lubricant into the motor should the motor shaft seal fail Motor’s stall torque could exceed recommended full load torques. A current limiting device such asan SCR control should be used to prevent damage. This issue is even more critical for low voltagemotors, typically no controller is used since motor is connected directly to a battery, so some type ofcurrent limit or fusing should be considered Overhung load capacities shown are at center of output shaft Bodine/Baldor direct interchangeTerms / WarningsTech InformationX-Ref / IndexMods / FactoryOptionsAccessories / KitsAC / DC ControlsGearmotorsDC MotorsIEC MotorsGearmotorsBuy: www.ValinOnline.com Phone 844-385-3099 Email: CustomerService@valin.com

PE350 Series - Parallel Shaft - DCSCR Rated - 25-371 In-Lbs . TorqueLow Voltage - 155-341 In-Lbs Torque72127506283165250500 111.3111.3111.3111.3111.31YNotesS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USF.L.Output Torque InputRPM (Lb.In.) HP3413252201551 81 41 41 4M1135243.00M1135244.00M1135245.00M1135246.00 OverGearmotorArm. F.L. hungListType & Ratio Volts Amps LoadPrice Model Number Frameto NZ156M34D25NZ157Specifications are subject to change without 28.721.021.021.0465327303267Dimensions 1YNotesS, USS, USS, USS, USY Note listing on inside back flapX-Ref / Index14426283CatalogNumberStock12 Volts - TENV - PE350 SeriesMods / FactoryOptionsY Note listing on inside back flapSpecifications are subject to change without noticeAccessories / 1135113.00M1135150.00Dimensions (inches)AC / DC Controls421 81 81 81 81 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 4OverGearmotorArm. F.L. hungListType & Ratio Volts Amps LoadPrice Model Number Frameto rStockF.L.Output Torque InputRPM (Lb.In.) HPDC Motors90 & 180 Volts - TENV - PE350 SeriesIEC MotorsGearmotorsPE350 SERIES - DCBuy: www.ValinOnline.com Phone 844-385-3099 Email: CustomerService@valin.comTerms / WarningsView On-line Technical InformationTech InformationALL DIMENSIONS IN INCHES

Parallel Shaft - P1100 Series - DCSCR Rated - 105-1112 In-Lbs. TorqueLow Voltage - 320-1087 In-Lbs. TorqueGeneral Specifications - SCR Rated Gearmotors: Performance matched for continuous duty service over 60:1 speed range Constant torque throughout the range when powered by a full-wave unfiltered SCR-type adjustablespeed control having a typical form factor of 1.3 to 1.4General Specifications - Low Voltage Gearmotors: Performance matched for continuous duty service Designed for battery power or can be used with a low voltage controller with form factor up to 1.05Features: Rugged die cast aluminum gear housing for maximum gear and bearing support Precision machined gearing, hardened for maximum load capability All gearing designed and rated to AGMA class 9 standards, and to withstand momentary shockoverload of 200% Oversized output bearings for greater overhung load capacity and long life High carbon alloy output shaft provides maximum strength and rigidity All needle bearing journals are precision ground after heat treating toprovide maximum fit and finish Heavy duty industrial oil seals keep lubricant in and dirt out Gears and bearings are splash lubricated with permanent, heavy duty gear oil Conduit box included as standardApplication Notes: These gearmotors are designed for mounting at any angle, but motor below the reducer should beavoided to prevent leakage of lubricant into the motor should the motor shaft seal fail Motor’s stall torque could exceed recommended full load torques. A current limiting device such asan SCR control should be used to prevent damage. This issue is even more critical for low voltagemotors, typically no controller is used since motor is connected directly to a battery, so some type ofcurrent limit or fusing should be considered Overhung load capacities shown are at center of output shaft For additional information, see Bulletin 1830 Bison/Dayton direct interchangeTerms / WarningsTech InformationX-Ref / IndexMods / FactoryOptionsAccessories / KitsAC / DC ControlsGearmotorsDC MotorsIEC MotorsGearmotorsBuy: www.ValinOnline.com Phone 844-385-3099 Email: CustomerService@valin.com

Parallel Shaft - P1100 Series - DCSCR Rated - 105-1112 In-Lbs . TorqueLow Voltage - 320-1087 In-Lbs . TorqueStockDC Motors90 Volts - Totally Enclosed - Rigid Base - P1100 SeriesOverGearmotorArm. F.L. hungListType & Ratio Volts Amps LoadPrice Model Number Frameto 1DCDC(lb.)XLXH810871 4108700.00 1,300 4D17NZ17P1103-48212902.770014.2412.74S, US, 121210301 4108701.00 1,300 4D17NZ18P1103-48143902.770014.2412.74S, US, 12187501 4108702.00 1,300 4D17NZ19P1103-4895902.770014.2412.74S, US, 12423531 4108703.00 1,268 4D17NZ20P1102-4842902.765014.2412.74S, US, 12602381 4108704.00 1,268 4D17NZ21P1102-4829902.762514.2412.74S, US, 12921601 4108705.00 1,268 4D17NZ22P1102-4819902.757514.2412.74S, US, 121351051 4108706.00 1,268 4D17NZ23P1102-4813902.752514.2412.74S, US, 121811121 2108707.00 1,405 4D17FZ23P1103-4895905.070016.4914.99S, US338221 2108708.00 1,405 4D17FZ24P1103-4853905.065016.4914.99S, US427051 2108709.00 1,379 4D17FZ25P1102-4842905.065016.4914.99S, US604761 2108710.00 1,379 4D17FZ26P1102-4829905.062516.4914.99S, US923201 2108711.00 1,379 4D17FZ27P1102-4819905.057516.4914.99S, US1352101 2108712.00 1,379 4D17FZ28P1102-4813905.052516.4914.99S, USF.L.Output Torque InputRPM (Lb.In.) HPCatalogNumberDimensions (inches)YNotes1 41 41 21 05320 7FZ53C/A - Check AvailabilityNote 12 - TENVSpecifications are subject to change without 2121221.021.040.040.0700625650575Dimensions 49YNotesS, US, 12S, US, 12S, USS, USY Note listing on inside back flapX-Ref / IndexP1100 SERIES - DCMods / . F.L. hungListType & Ratio Volts Amps LoadPrice Model Number Frameto 1DCDC(lb.)Accessories / KitsF.L.Output Torque InputRPM (Lb.In.) HPAC / DC Controls12 Volts - Totally Enclosed - Rigid Base - P1100 SeriesGearmotorsY Note listing on inside back flapNote 12 - TENVSpecifications are subject to change without noticeIEC MotorsGearmotorsBuy: www.ValinOnline.com Phone 844-385-3099 Email: CustomerService@valin.comTerms / WarningsView On-line Technical InformationTech InformationALL DIMENSIONS IN INCHES

Right-Angle DC GearmotorsSCR Rated - 5-135 In-Lbs . TorqueLow Voltage - 25-135 In-Lbs . TorqueX-Ref / IndexMods / FactoryOptionsAccessories / KitsAC / DC ControlsGearmotorsDC MotorsIEC MotorsGearmotorsGeneral Specifications - SCR Rated Gearmotors: Performance matched for continuous duty service over 60:1 speed range Constant torque throughout the range when powered by a full-wave unfiltered SCR-type adjustablespeed control having a typical form factor of 1.3 to 1.4General Specifications - Low Voltage Gearmotors: Performance matched for continuous duty service Designed for battery power or can be used with a low voltage controller with form factor up to 1.05Features: Worm-type right-angle gearing features hardened, steel worm with bronze worm wheel for long lifeand quiet operation Precision machined aluminum gear housing Lubrication is permanent with an oil bath Gearbox has all ball bearings Output shaft is field interchangeable from left hand to right hand style by reassembly Double output shaft available as a factory option Optional conduit box available, see page 350 Optional gearbox base available (10 Series only), see page 350Application Notes: These right-angle gearmotors have a lubrication breather positioned for horizontal mounting. Forother mountings, the breather plug must be reoriented by using a 90 deg 1/8” NPT taper pipeelbow (See drawing). Elbow not available from LEESON These gearmotors are designed for mounting at any angle, but motor below the reducer should beavoided to prevent leakage of lubricant into the motor should the motor shaft seal fail Overhung load capacities shown are at center of output shaft For additional information, see Bulletin 183013 SERIES - DCTerms / WarningsTech Information10 SERIES - DCBuy: www.ValinOnline.com Phone 844-385-3099 Email: CustomerService@valin.com

C/A C/AC/A C/A .148.148.148.14S, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USS, USC/A - Check AvailabilitySpecifications are subject to change without noticeY Note listing on inside back flap42250621258025135901 81 81 41 35252.00C/A OverGearmotorArm. F.L. hungListType & Ratio Volts Amps LoadPrice Model Number Frameto 1 DCDC M34D25NZ161C/A - Check 201212121211.011.021.021.0235235235235Dimensions .54.54.510.3910.3912.6412.64XH YNotes5.895.898.148.14S, USS, USS, USS, USX-Ref / IndexF.L.Output Torque InputRPM (Lb.In.) HPStock12 Volts - TENV - Right-Angle SeriesMods / M1135065.00M1135046.00M1135066.00Accessories / Kits1 171 171 171 171 171 121 121 121 121 121 81 81 81 81 81 81 81 81 81 41 41 41 41 41 41 41 41 41 4AC / DC 125125909050503030Dimensions gNumberOverGearmotorArm. F.L. hungListType & Ratio Volts Amps LoadPrice Model Number Frameto 1DCDC(lb.)DC MotorsF.L.Output Torque InputRPM (Lb.In.) HPStockRight-Angle DC GearmotorsSCR Rated - 5-135 In-Lbs . Torque & Low Voltage - 25-135 In-Lbs . Torque90 & 180 Volts - TENV - Right-AngleIEC MotorsGearmotorsY Note listing on inside back flapSpecifications are subject to change without noticeTech InformationBuy: www.ValinOnline.com Phone 844-385-3099 Email: CustomerService@valin.comTerms / WarningsView On-line Technical Information

Bravo Series 12 SUB-FHP - DCRight-Angle GearmotorsGeneral Specifications - SCR Rated Gearmotors: Performance matched for continuous duty service over60:1 speed range Constant torque throughout the range when powered by a full-wave unfiltered SCR-type adjustablespeed control having a typical form factor of 1.3 to 1.4General Specifications - Low Voltage Gearmotors: Performance matched for continuous duty service Designed for battery power or can be used with a low voltage controller with form factor up to 1.05Features: Worm-type right-angle gearing features hardened, steel worm with bronze worm wheel for long lifeand quiet operation Single piece die cast aluminum alloy housing is vacuum impregnated with Resinol RT for protectionand sealing Light weight gearbox combines high tensile strength along with being precision machined for alignment of bearings and gearing High temperature Nitrile seals for optimum seal life Gearbox provided with solid output shaft, but can be converted to a hollow output shaft. Simplyremove the solid shaft by removing the Snap rings T-base feet provided are removable to convert to face mounti

Quick Reference -Stock Sub-FHP Gearmotors P240 &P300 Series Gearmotors PE350 Series Gearmotors OS300 Series Gearmotors Single Phase 115/230V 43-391 In-Lbs Output Torque Page 342 DC SCR 90 &180V 27-353 In-Lbs Output Torque Low Voltage (12V) 113-353 In-Lbs torque Page 322 Single Phase 115/230V 25-341 In-Lbs Output Torque

Related Documents:

Work out the gear ratios of these gears: (numbers inside the circles are the numbers of teeth on each gear) Blue drive gear, green driven gear, pink idler gear, yellow compound gear 1: Simple meshed gear 2: Simple gear train with idler gear 15 3: Compound gear train 4: Choose the correct words to make these statements true for these gear trains.

GEAR PUMPS MOTORS & FLOW DIVIDERS we www.catford.com.au email salescatford.com.au tel 0418 641 566 117 Vivoil Group 1 Pumps 120 Vivoil Group 2 Pumps 124 Vivoil Group 3 Pumps 130 Multiple Pump Nomenclature 134 Group 1 Pumps 136 Group 2 Pumps 137 Group 3 Pumps 139 Log Splitter Pumps 141 Vivoil Group 1 Gear Motors 142 Vivoil Group 2 Gear Motors 145 Vivoil Group 3 Gear Motors 148

3. Explain what a gear train does? 4. Explain what a simple gear train is? 5. Explain torque? 6. What does a larger gear driving a smaller gear achieve? 7. What does a smaller gear driving a larger gear achieve? 8. What is the driven gear? 9. What is the driver gear? 10. What is the idler gear? 11. What is the calculation for working out gear .

form a gear set or a gear train . In a gear set, the input gear is called _ gear. The output gear is called the _ gear. Note: An idler gear or intermediate gear changes direction of rotation without change in gear set speed or torque Spinner &

Dr. Leeson’s research explores the economics of anarchy. His most recent work focuses on the economics of pirates. His paper, “An-arrgh-chy: The Law and Economics of Pirate Organization,” was recently published in the Journal of Political Economy. Dr. Leeson is the author of The Invisible Hook: The Hidden Economics of Pirates. Dr. Leeson .

The LEESON FHP Series Drives are solid state, variable-frequency AC motor drives. The FHP Series utilizes a 115 or 230 VAC, 50/60 Hz, single-phase input, and is factory calibrated for an output of 0 to 60 Hz. They will operate any 1.5 HP or smaller, 208/230-volt three-phase-AC-induction, single-phase permanent split capacitor

Frontiers in Heat Pipes (FHP), 1, 023003 (2010) DOI: 10.5098/fhp.v1.2.3003 Global Digital Central ISSN: 2155-658X 1 LOCAL HYDRODYNAMICS OF FLOW IN A PULSATING HEAT PIPE: . The bubbles act as pumping elements, transporting the entrapped liquid slugs in a complex oscillating-translating-vibratory

the standard three-rail shear test, as described in ‘‘ASTM D 4255/D 4255M The standard test method for in-plane shear properties of polymer matrix composite materials by the rail shear method’’. This setup, however, requires drilling holes through the specimen. In this study, a new design based on friction and geometrical gripping, without the need of drilling holes through the .