Pub. EC-0404 SOLENOID CONTROLLED PILOT OPERATED . - FLUID POWER

1y ago
12 Views
2 Downloads
1.11 MB
51 Pages
Last View : 2m ago
Last Download : 2m ago
Upload by : Luis Wallis
Transcription

Pub. EC-0404SOLENOID CONTROLLED PILOTOPERATED DIRECTIONAL VALVESDSHG-01/03/04/06/10PILOT OPERATED DIRECTIONAL VALVESDHG/04/06/10DIRECTIONALMANUALLY OPERATEDCONTROLSDIRECTIONAL VALVESDMG-01/03/04/06/10DMT-03/06/10General InformationUp to 31.5 MPa (4570 PSI), 1100L/min (291 U.S.GPM)Solenoid contorolled Pilot Operated Valves . Page 4Thease valves are composed of a solenoid operated pilot valve and a pilotoperated slave valve. When a solenoid is energised the pilot valve directs theflow to move the spool of the slave valve, thus changing the direction of flowin the hydraulic circuit.EHigh Pressure High FlowIn these valves, the nominal size "04" can provide 300 L/min (79.3 U.S.GPM),"06" can provide 500 L/min (132 U.S.GPM) and "10" can provide 1100 L/min(291 U.S.GPM) in the maximum flow respectively and they can also withstandsuch a high pressure as 31.5 Mpa {4570 PSI} as the maximum operatingpressure. With these features of high pressure and high flow, the valves canmake the size or configuration of the equipment compact.Low Pressure DropAs the pressure drop of each size of the valve becomes minimal, the more ofenergy saving of the equipment is possible.Easy Change of Pilot and Drain SystemThe change of the pilot from external to internal and the change of the drainfrom internal to external or viceversa can be done easily by putting on orremoving the relevant plug on the valve.Pilot Operated Directional ValvesThese valves perform a change over of spool byhydraulic pilot and shift the direction of oil flow. Page34XPY. Page40These valves may be used to manually shift the spoolposition and change the direction of oil flow.Manually Operated Directional ValvesNo.1

Solenoid ControlledPilot Operated Directional ValvesPilot Operated Directional ValvesManually Operated Directional ValvesDIRECTIONALCONTROLSSolenoids / MountingSolenoids(Only for Solenoid Controlled Pilot Operated Directional Valves)Solenoid connectors (DIN Connector)The solenoid connectors are conform to the international standard ISO 4400 (Fluid power systems and componentsThree-pin electrical plug connectors-Characteristics and requirements).AC Solenoids50-60 Hz common service solenoids do not require rewiring when the applied frequency is changed.DC Solenoids (Reputable K-Series)These DC solenoids have surge absorbers for K-series functions. The three advantages of them are as mentionedbelow:1. Since surge voltage can be controlled to a very low figure, electric control devices, such as a computer, can be usedwithout any interference like noise.2. There being no spark between contacts, the life of the relay becomes longer.3. Time lag for spool return after de-energisation of the solenoid is very short.R Type SolenoidsThese are rectifier and surge absorber incorporated direct current solenoids which can be used by connecting directlyto the AC power source. They have, like other DC solenoids, such advantages that the sound in on-off operation isquite low and the coils are hardly burnt out even if the spool is stuck at the half way of its changeover for contaminantparti-cles etc. Moreover, they can be used almost permanently without being affected by a surge voltage from the outside.Thus, they are the solenoids of high reliability and durability.Insulation Class of SolenoidClass HMountingMounting surface dimensions confrom to ISO 4401, Hydraulic fluild power-Four-port directional control valvesMounting surfaces.Model NumbersISO Code of Mounting SurfaceDSHG-01DMG-01ISO 4401-AB-03-4-ADMG-03ISO 4401-AC-05-4-ADSHG-03ISO 4401-AC-05-4-A(S)-DSHG-04DHG-04DMG-04ISO 4401-AD-07-4-A(S)-DSHG-06DHG-06DMG-06ISO 4401-AE-08-4-A(S)-DSHG-10DHG-10DMG-10ISO 4401-AF-10-4-AThe main ports conform to ISO 4401-AC-05-4-A. The pilot anddrain ports conform to the ISO.No.2

Solenoid ControlledPilot Operated Directional ValvesDIRECTIONALCONTROLSPilot Operated Directional ValvesManually Operated Directional ValvesHydraulic Fluids / InstructionsHydraulic FluidsFluid TypesAny type of hydraulic fluid, listed in the table below can be used.Type of FluidsRemarksPetroleum Base OilUse fluids equivalent to ISO VG32 or VG46.Use phosphate ester or polyol ester fluid.When phosphate ester fluid is used, prefix"F-" to the model number because the special seals (fluororubber) are required to be used.Synthetic FluidsWater Containing FluidsUse water-glycol fluids or W/O emulsion fluids.Note) 1: For two types of manually operated directional valves, DMT-06, 06X and DMT-10, 10X, only petroleum baseoils and polyol ester type fluids are available.2: For use with hydraulic fluids other than those listed above, consult your Yuken representatives in advance.Recommended Viscosity and Oil TemperaturesAlways be sure to use hydraulic fluids within the stipulated conditions shown below:Viscosity: 15 to 400 mm2/s (77 to 1800 SSU), Temperature: -15 to 70 C (5 to 160 F)Control of ContaminationDue caution must be paid to maintaining control over contamination of the hydraulic fluids which may otherwise leadto breakdowns and shorten the life of the valve. Please maintain the degree of contamination within NAS 1638-Grade12. Use 25 μm or finer line filter.InstructionsSOL aLSOL bL'Solenoid EnergisationIn no-spring type, either solenoid of the two should be energised continuously to avoid malfunction.For double solenoid valves do not energise both at the sametime as it will result in coils burning out.Valve Tank PortAvoid connecting the valve tank port to a line with possiblesurge pressure.Piping end of tank line should be submerged in oil.Pilot Drain Port for Solenoid Controlled Pilot OperatedDirectional ValveAvoid connecting the valve pilot drain port to a line withpossible surge pressure.Piping end of drain should be submerged in oil.Shockless TypeIn order to benefit from a shockless operation, it is necessaryto fill the drain line with operating oil.Only after the tank line has been filled with operating oil, startthe operation of the valve on a regular basis.Operating Force for Manual Override Push PinPlease note that as the back pressure of the drain line rises,manually override push pin turns hard to operate (See thegraph below).30N15020120105001bf.OperatingForceMounting PostureIn case No-spring detent type and No-spring type valves areused in the solenoid de-energised state, install the valve insuch a way that the axis L-L' becomes horizontal to get thedetent effect firmly. For the valve types other than the above,there are no restrictions on the mounting posture.0MPa002110020030034004500PSIDrain Line Back PressureNo.3E

Solenoid Controlled Pilot OperatedDirectional ValvesDSHG-01/03/04/06/10S-DSHG-04/06/10Sub-plate tions1Max. ChangeMax. T-Line BackMin 2Max. Flow Max.Max. Pilotover Frequency Approx.PressureOperatingRequiredModel NumbersL /minPressureMPa(PSI)min-1(Cycles/Min) MassPilot Pres.Pressure(U.S.GPM) MPa(PSI) MPa(PSI) MPa(PSI) Ext.Drain Int.Drain AC DCR kg(1bs.)DSHG-01-3C - -13/1380/13903.5 (7.7)40 (10.6) 21 (3050) 21 (3050) 1.0 (150) 16 (2320) 16 (2320) 120 120 120DSHG-01-2B - -13/1380/13902.9 (6.4)DSHG-03-3C - -13/13907.2(15.9)160 (42.3) 25 (3630) 25 (3630) 0.7 (100) 16 (2320) 16 (2320) 120 120 120 7.2(15.9)DSHG-03-2N - -13/13906.6(14.6)Standard DSHG-03-2B - -13/1390Type (S-)DSHG-04-3C - -51/51908.8(19.4)(S-)DSHG-04-2N - -51/5190 300 (79.3) 31.5 (4570) 25 (3630) 0.8 (120) 21 (3050) 16 (2320) 120 120 120 8.8(19.4)(S-)DSHG-04-2B - -51/51908.2(18.1)(S-)DSHG-06-3C - -52/529012.7 (28)325 (3630) 0.8 (120)(S-)DSHG-06-2N - -52/5290120 120 120 12.7 (28)500 (132) 31.5 (4570)21 (3050) 16 (2320)(S-)DSHG-06-2B - -52/529012.1 (27)21 (3050) 1.0 (150)110 110 110 13.5 (30)Shockless (S-)DSHG-06-3H - -52/5290Type (S-)DSHG-10-3C - -42/4290120 120 100 45.3(100)25 (3630)3(S-)DSHG-10-2N - -42/4290100 100 100 45.3(100)1100 (291) 31.5 (4570)1.0 (150) 21 (3050) 16 (2320)(S-)DSHG-10-2B - -42/429044.7 (99)21 (3050)606050(S-)DSHG-10-3H - -42/429053.1(117)ValveType1. The maximum flow means the limited flow without inducing anyabnormality to the operation (changeover) of the valve. For details,please refer to the "List of Standard Models and Maximum Flow" onpages 9 to 13.2. In case of internal drain type valve, the differential pressure betweenpilot pressure and back pressure at tank port should be kept more thanthe minimum pilot pressure.3. The minimum pilot pressure for the valve with pilot piston is 1.8 MPa(260 PSI).No.4Yuken can offer flanged connection valves describedbelow. Consult Yuken for the details.Rated FlowMax. PressureL /min (U.S.GPM) MPa (PSI)315 (83)DSHF-10- - -27 DSHF-16- - -37 500 (132)21 (3050)DSHF-24- - -28 1200 (317)DSHF-32- - -27 2400 (634)Model Numbers

Solenoid Controlled Pilot OperatedDirectional LCONTROLSSolenoid Ratings / Sub-platesSolenoid RatingsValve TypeCoilTypeElectric 0ShocklessTypeDC (K Series)AC DC Rectified (R)D12D24D48R100R2006050605060506050/60Voltage (V)Current & Power at Rated VoltageSource Rating Serviceable Range Inrush (A)Holding (A) Power (W)10080 - 1102.420.511002.140.3790 - 1201102.350.4496 - 1322.020.42120108 - 1441.780.31200160 - 2201.210.252001.070.19180 - 2402201.180.22192 - 2641.010.21240216 - 2880.890.151210.8 - 13.22.452421.6 - 26.41.23294843.2 - 52.80.6110090 - 1100.3329200180 - 2200.16Inrush current in the above table show rms values at maximum stroke.The coil type numbers in the shaded column are handled as optional extras.In case these coils are required to be chosen, please confirm the time ofdelivery with us before ordering.CSA Approved Solenoid ValveThe "DSHG" series valve have been approved by theCSA(Candian Standards Association). consult us for SHG-04DSHG-06DSHG-10Japanese Standard "JIS"Approx.Sub-plateThreadMassModel NumbersSizekg (1bs.)DSGM-01-30Rc 1/8 0.8 (1.8)DSGM-01X-30Rc 1/4 0.8 (1.8)DSGM-01Y-30Rc 3/8 0.8 (1.8)DSGM-03-40Rc 3/8 3.0 (6.6)DSGM-03X-40Rc 1/2 3.0 (6.6)DSGM-03Y-40Rc 3/4 4.7 (10.4)DHGM-03Y-10Rc 3/4 4.7 (10.4)DHGM-04-20Rc 1/2 4.4 (9.7)DHGM-04X-20Rc 3/4 4.1 (9.0)DHGM-06-50Rc 3/4 7.4 (16.3)DHGM-06X-50Rc 17.4 (16.3)DHGM-10-40Rc 1-1/4 21.5 (47.4)DHGM-10X-40 Rc 1-1/2 21.5 (47.4)European Design StandardN. American Design adMassMassModel NumbersSizeModel NumbersSizekg (1bs.)kg (1bs.)0.8 (1.8)DSGM-01-30801/8 BSP.F 0.8 (1.8) DSGM-01-30901/8 NPT0.8 (1.8)DSGM-01X-3080 1/4 BSP.F 0.8 (1.8) DSGM-01X-30901/4 NPT0.8 (1.8)DSGM-01Y-30903/8 NPT3.0 (6.6)DSGM-03-21803/8 BSP.F 3.0 (6.6) DSGM-03-21903/8 NPT3.0 (6.6)DSGM-03X-2180 1/2 BSP.F 3.0 (6.6) DSGM-03X-21901/2 NPT4.7 (10.4)DSGM-03Y-2180 3/4 BSP.F 4.7 (10.4) DSGM-03Y-21903/4 NPT4.7 (10.4)DHGM-03Y-1080 3/4 BSP.F 4.7 (10.4) DHGM-03Y-1090 3/4 NPT4.4 (9.7)DHGM-04-20801/2 BSP.F 4.4 (9.7) DHGM-04-20901/2 NPT4.1 (9.0)DHGM-04X-2080 3/4 BSP.F 4.1 (9.0) DHGM-04X-2090 3/4 NPT7.4 (16.3)DHGM-06-50803/4 BSP.F 8.5 (18.7) DHGM-06-50903/4 NPT1 NPT7.4 (16.3)DHGM-06X-5080 1 BSP.F8.5 (18.7) DHGM-06X-50901-1/4 NPT 21.5 (47.4)DHGM-10-4080 1-1/4 BSP.F 21.5 (47.4) DHGM-10-4090DHGM-10X-4080 1-1/2 BSP.F 21.5 (47.4) DHGM-10X-4090 1-1/2 NPT 21.5 (47.4)DSGM-03 is available only for Internal pilot-Internal drain type (Use DHGM-03Y for other valves).Sub-plates are available. Specify the sub-plate model number from the table above.When sub-plates are not used, the mounting surface should have a good machined finish.No.5E

ional Valve,Sub-plateMounting3210232B: SpringOffsetN: No-SpringC: SpringCentredH: PressureCentredB: SpringOffsetN: No-SpringC: SpringCentredB: SpringOffsetA1A222(Omit if not required)22, 4, 40A B(3, 7) 1 (Omit if not required)2, 4, 40(3, 7)22, 4, 40A B1(Omit if not required)(3, 7)2, 4, 4060, 10, 123, 5, 6 17, 9, 11-C2-ETExternal Pilot (E)Internal PilotPilot ConnectionInternal Drain (T)External DrainInternal Drain (T)External DrainDrain Connection-R2Omit if notrequiredC1C2:With C1 &C2 ChokeC2:With C2ChokeC1:With C1ChokeNo restrictions in the combination on usHold back pressure in the tank line so that thedifference between pilot pressure and drain pressureis always more than minimum required pilotpressure.Combination is not applicableCare in ApplicationAC:A100 , A200A120 , A240AC DCR100 , R200DC:D12 , D24D48AC:A100 , A200A120 , A240CoilType-A100-C-H-N-52- C:PushButton &Lock NutNone:ManualOverridePinH:Refer to nnectorTypeNone:TerminalBox anDesignStandard(Applicableonly forDSHG-01)None:JapaneseStandard"JIS" None:JapaneseStandard"JIS"ManualBult-in Type of Elec- Design DesignOverride of Orifice for trical Conduit NumberStandardPilot Valve Pilot Line Connection-LL(Omit if not required)L(Omit if not required)L(Omit if not required)L(Omit if not required)Models withReverse Mtg.of SolenoidIn the table above, the symbols and numbers highlighted with shade represent the optional extras.The valves with model number having such optional extras are handles as options, therefore pleaseconfirm the time of delivery with us before ordering.1. Shckless type (S-DSHG) are not available for spool type marked ( ).2. As for the details of the valve using the neutral position and the side position (either SOL a orSOL b side), please refer to page 14. Furthermore, the spool types other than "2", "4", "40" (3,7) are also available.3. In spool-spring arrangement "H" (Pressure centred models), the valves with stroke adjustment(R ) and pilot-piston (P ) are not available.4. N1 stands for Plug-in connector with solenoid indicator light. N1 is not available for R-typesolenoids.5. In spool-spring arrangement "H" (Pressure centred models), in case the pilot pressure is morethan 10 MPa (1450 PSI), please specify that the valve should have the built-in orifice to thepilot line.DC:R2: With Stroke Adj., D12 , D24D48Both EndsRA: With Stroke Adj., AC DCPort "A" EndR100 , R200RB: With Stroke Adj.,Port "B" EndP2: With Pilot Piston,Both EndsPA: With Pilot Piston,Port "A" EndPB: With Pilot Piston,Port "B" EndR2:With StrokeAdjustment,Both EndsRA:None: None:With StrokeInternal External Adjustment,PilotDrainPort "A" EndRB:With StrokeE:T:Adjustment,External Internal Port "B" EndPilotDrainSpecial Two Models with PilotSpool Control 3DrainModificationPositionPilot Choke Connec- Connection(Omit if not required)tionValveValve2, 4, 40A 2(3, 7) 1 (Omit if not required)2, 4, 4060, 10, 123, 5, 6 17, 9, 112344072, 3, 440, 5, 607, 9, 1011, 12C: SpringCentred3N: No-Spring2, 3, 440, 7B: SpringOffset20604030132, 3, 440, 5, 607, 9, 1011, 12SpoolType2C: SpringCentredNo. ofSeries Valve Valve Spool-SpringNumber Size Position ArrangementS- DSHG -06 -2Note : In spool type "3", "5", "6", "60", and "7", the combination applicable between pilot systemand drain system is as described in the table below.Omit if lsF-Model Number DesignationSolenoid Controlled Pilot OperatedDirectional ValvesDSHG-01 / 03 / 04 / 06 / 10S-DSHG-04 / 06 / 10DIRECTIONALCONTROLSModel Number Designation

Solenoid Controlled Pilot OperatedDirectional -04/06/10Mounting BoltMounting BoltMouting BoltModelNumbersJapanese Standard "JIS"European Design StandardNameMBK-01-01-30MBK-01-02-30M6 35 Lg.M6 45 Lg.M10 50 Lg.M12 60 Lg.M20 75 Lg.3DSHG-01Mtg. Bolt KitDSHG-03Soc. Hd. Cap Screw(S-)DSHG-04Soc. Hd. Cap Screw(S)-DSHG-06(S)-DSHG-10Soc. Hd. Cap ScrewSoc. Hd. Cap Screw12N. American Design StandardMBK-01-01-3090 1MBK-01-02-3090 21/4-20 UNC 1-3/4 Lg.1/4-20 UNC 1-3/4 Lg.3/8-16 UNC 2 Lg.1/2-13 UNC 2-1/2 Lg.3/4-10 UNC 3 Lg.Qty.Tightening TorqueNm (in. 1bs.)1 set5-642466121258100473-151572123585(43 - 52)(104(104(504(868(4106-130)130)625)1068)5078)1. For Internal Pilot-Internal Drain.2. For External Pilot or External Drain.3. Mounting bolt kit is common to that of 01 series modular valves.Refer to figure below for the dimensions of bolt kit.Stud Bolt"B" Thd.Both Ends9(.35)9(.35)ADIMENSIONS INMILLIMETRES (INCHES)Nut8.5 Dia.(.33)"B" Thd.9(.35)4(.16)Model 1-02-3090A mm (In.)94 (3.70)134 (5.28)94 (3.70)134 (5.28)"B" Thd.M5No.10-24 UNC15(.59)No.7E

Solenoid Controlled Pilot OperatedDirectional -04/06/10OptionsOptionsModels with Pilot Choke AdjustmentWhen the adjustment screw is turned clockwise,changeover speed of the main spool becomes slow. Incase of the spring centred valves in particular, makingslow of the returning speed of the main spool to theneutral position is possible with a C2 choke valve.These choke valves can be used in combination withthe valves of spring centred, no-spring, offset, pressurecentred and the valves with stroke adjustment.Pressure Centred Models (3H )The pressure centered type can be used when thereturning of the main spool to the neutral position isrequired to be firmily.Graphic Symbols (Ex.: External Pilot-External Drain)(Only for 3H6, 3H60)Graphic Symbols (Ex.: Spring Centred)AbaPTVABPTabYC2 ChokeC1 ChokeBaDSHG-01,06,10bYXV XModels with Stroke Adjustment (R2, RA, RB)When the adjustment screw is screwed in , the mainspool stroke becomes short and flow rate reduces.YPTGraphic Symbols (Ex.: Spring Centred)AB"R2" ModelsDSHG-03, 04C2 ChokeaABY PTabb"RA" ModelsC1 ChokeYPTBAABY PTab"RB" ModelsABY PTaModels with Pilot Piston(P2, PA, PB)The valves with a pilot piston can be used when thehigh speed changeover of the main spool is required.However, please not that in case of spring centeredvalves, there is no change in the returning speed of themain spool to the neutral position even with the pilotpiston.Additional Mass of OptionsAdd the mass described below to the mass of standardmodels on page 4, if options are required.Graphic Symbols (Ex.: Spring Centred)ModelNumbers"P2" ModelsaWABY PTbV"PA" ModelsaAY PBTWNo.8ABY PTDSHG-03(S-)DSHG-04(S-)DSHG-06(S-)DSHG-10Model with PilotChoke Adj.C1, 1.3(2.9)1.3(2.9)1.3(2.9)kg (1bs.)Models withStroke Adj.PAP2PB0.6(1.3) 0.3 (.7)1.0(2.2) 0.5(1.1)1.0(2.2) 0.5(1.1) 1.2(2.6) 06(1.3)3.6(7.9) 1.8(4.0) 3.7(8.2) 1.85(4.1)Models withPilot PistonPAP2PBbV"PB" ModelsabbOptions on Pilot ValveThe same options to DSG-01 series valves are available.Please refer to the Catalogue No. Pub. EC-0402 for thedetails.

Solenoid Controlled Pilot OperatedDirectional ValvesDSHG-01DIRECTIONALCONTROLSList of Standard Models and Maximum FlowThree PositionsTwo PositionsSpring CentredSpring CentredGraphic SymbolSpool TypeAGraphic SymbolBbaYPMaximum FlowL /min (U.S.GPM)7 MPa14 MPa21 MPa(1020 PSI) (2030 PSI) (3050 PSI)Maximum FlowL /min (U.S.GPM)BbYTModel NumbersAPTModel Numbers7 MPa14 MPa21 MPa(1020 PSI) (2030 PSI) (3050 PSI)"2"DSHG-01-3C240 (10.6)40 (10.6)40 (10.6)DSHG-01-2B240 (10.6)40 (10.6)40 (10.6)"3"DSHG-01-3C340 (10.6)40 (10.6)40 (10.6)DSHG-01-2B340 (10.6)40 (10.6)40 (10.6)"4"DSHG-01-3C440 (10.6)40 (10.6)40 (10.6)DSHG-01-2B440 (10.6)40 (10.6)40 (10.6)"40"DSHG-01-3C4040 (10.6)40 (10.6)40 (10.6)DSHG-01-2B4040 (10.6)40 (10.6)40 (10.6)"5"DSHG-01-3C540 (10.6)40 (10.6)40 (10.6)"60"DSHG-01-3C6040 (10.6)40 (10.6)40 (10.6)"7"DSHG-01-3C740 (10.6)40 (10.6)40 (10.6)DSHG-01-2B740 (10.6)40 (10.6)40 (10.6)"9"DSHG-01-3C940 (10.6)40 (10.6)40 (10.6)"10"DSHG-01-3C1040 (10.6)40 (10.6)40 (10.6)"11"DSHG-01-3C1140 (10.6)40 (10.6)40 (10.6)"12"DSHG-01-3C1240 (10.6)40 (10.6)40 (10.6)Notes ) 1. Max. flow shows value at pilot pressure more than 1 MPa (150 PSI)2. Max. flow in the table above represents the value in the flow condition of P A B T (or P B A T) as shown in the circuit diagram right.In case the valve is used in the condition that either A or B port is blocked, the maximum flow differsaccording to a hydraulic circuit, therefore, please consult us for details.ABPTbaNo.9E

Solenoid Controlled Pilot OperatedDirectional ValvesDSHG-03DIRECTIONALCONTROLSList of Standard Models and Maximum FlowThree PositionsSpring CentredGraphic SymbolASpool TypeBbaYPMaximum FlowL /min (U.S.GPM)T7 MPa14 MPa25 MPa(1020 PSI) (2030 PSI) (3630 PSI)85 (22.5) 60 (15.9)160 (42.3)160 (42.3) 95 (25.1)Model Numbers"2"DSHG-03-3C2"3"DSHG-03-3C3160 (42.3) 160 (42.3) 160 (42.3)"4"DSHG-03-3C4160 60160 (42.3) 160 (42.3)"7"DSHG-03-3C7160 (42.3)"9"DSHG-03-3C9160 (42.3)"10"DSHG-03-3C10160 (42.3)"11"DSHG-03-3C11160 (42.3)"12"DSHG-03-3C12160 (42.3)85 (22.5)160 (42.3)85 (22.5)160 (42.3)160 (42.3)85 (22.5)160 (42.3)160 (42.3)85 (22.5)160 (42.3)85 (22.5)160 (42.3)85 (22.5)160 (42.3)85 (22.5)160 (42.3)85 (22.5)160 (42.3)60 (15.9)95 (25.1)60 (15.9)95 (25.1)60 (15.9)95 (25.1)125 (33.0)160 (42.3)60 (15.9)95 (25.1)60 (15.9)95 (25.1)60 (15.9)95 (25.1)60 (15.9)95 (25.1)60 (15.9)95 (25.1)Two PositionsNo-SpringSpring OffsetGraphic SymbolASpool TypeGraphic SymbolBabYPMaximum FlowL /min (U.S.GPM)AbYTModel 40"DSHG-03-"7"2N407 MPa14 MPa25 MPa(1020 PSI) (2030 PSI) (3630 PSI)85 (22.5)160 (42.3) 160 (42.3)160 (42.3)85 (22.5)160 (42.3) 160 (42.3)160 (42.3)85 (22.5)160 (42.3) 160 (42.3)160 (42.3)85 (22.5)160 (42.3) 160 (42.3)160 (42.3)85 (22.5)160 (42.3) 160 (42.3)160 (42.3)P160 (42.3)2. Max. flow in the table above represents the value in the flowcondition of P A B T (or P B A T) as shownin the circuit diagram right.In case the valve is used in the condition that either A or B portis blocked, the maximum flow differs according to a hydrauliccircuit, therefore, please consult us for details.No.10TModel Numbers7 MPa14 MPa25 MPa(1020 PSI) (2030 PSI) (3630 PSI)DSHG-03-2B2160 (42.3) 160 (42.3)DSHG-03-2B3160 (42.3) 160 (42.3)DSHG-03-2B4160 (42.3) 160 (42.3)DSHG-03-2B40160 (42.3) 160 (42.3)DSHG-03-2B7160 (42.3) 160 (42.3)Notes:1. The relation between max. flow and pilot pressure in the tableabove is as shown below.(Example)Maximum flow rate is constant regardless of pilot pressure.Pilot Pressure more than 0.7 MPa (100 PSI).Maximum FlowL /min (U.S.GPM)BPilot Pressure at 0.7 MPa (100 PSI).85 (22.5)160 (42.3)Pilot Pressure at 1 MPa (150 PSI).ABPTba85 (22.5)160 (42.3)85 (22.5)160 (42.3)85 (22.5)160 (42.3)85 (22.5)160 (42.3)85 (22.5)160 (42.3)

Solenoid Controlled Pilot OperatedDirectional ValvesDSHG-04 / S-DSHG-04DIRECTIONALCONTROLSList of Standard Models and Maximum FlowThree PositionsSpring CentredGraphic SymbolMaximum FlowL /min (U.S.GPM)A BSpool TypebaYPT10 MPa 16 MPa 25 MPa 31.5 MPa(1450 PSI) (2320 PSI) (3630 PSI) (4570 PSI)DSHG-04-3C2 300 (79.3) 300 (79.3) 200 (52.8) 145 (38.3)(S-)DSHG-04-3C2 300 (79.3) 250 (66.1) 120 (31.7) 110 (29.1)Model Numbers"2""3"DSHG-04-3C3 300 (79.3) 300 (79.3) 300 (79.3) 300 (79.3)DSHG-04-3C4 300 (79.3)(S-)DSHG-04-3C4 300 (79.3)DSHG-04-3C40 300 (79.3)(S-)DSHG-04-3C40 300 (79.3)"4""40"300 (79.3)300 (79.3)300 (79.3)250 (66.1)250 (66.1)140 (37.0)200 (52.8)120 (31.7)165 (43.6)110 (29.1)145 (38.3)110 (29.1)"5"DSHG-04-3C5 250 (66.1) 250 (66.1) 245 (64.7) 245 (64.7)"6"DSHG-04-3C6 300 (79.3) 260 (68.7) 245 (64.7) 235 (62.1)"60"DSHG-04-3C60300 (79.3) 300 (79.3) 300 (79.3) 300 (79.3)(S-)DSHG-04-3C60"7"DSHG-04-3C7 300 (79.3) 300 (79.3) 200 (52.8) 145 (38.3)"9"DSHG-04-3C9 300 (79.3) 300 (79.3) 280 (74.0) 250 (66.1)"10"DSHG-04-3C10 300 (79.3) 300 (79.3) 200 (52.8) 150 (39.6)(S-)DSHG-04-3C10 300 (79.3) 250 (66.1) 120 (31.7) 110 (29.1)"11"DSHG-04-3C11 300 (79.3) 260 (68.7) 160 (42.3) 140 (37.0)"12"DSHG-04-3C12 300 (79.3) 280 (74.0) 170 (44.9) 135 (35.7)(S-)DSHG-04-3C12 300 (79.3) 250 (66.1) 120 (31.7) 110 (29.1)ETwo PositionsSpring OffsetNo-SpringGraphic SymbolASpool TypebYP"3"Maximum FlowL /min (U.S.GPM)AMaximum FlowL /min (U.S.GPM)BbYTModel Numbers"2"Graphic SymbolBaPT10 MPa 16 MPa 25 MPa 31.5 MPaModel Numbers(1450 PSI) (2320 PSI) (3630 PSI) (4570 PSI)10 MPa 16 MPa 25 MPa 31.5 MPa(1450 PSI) (2320 PSI) (3630 PSI) (4570 PSI)(S-)DSHG-04-2N2 300 (79.3) 300 (79.3) 300 (79.3) 300 (79.3) (S-)DSHG-04-2B2 300 (79.3) 300 (79.3) 300 (79.3) 300 (79.3)DSHG-04-2N3 300 (79.3) 300 (79.3) 300 (79.3) 300 (79.3)DSHG-04-2B3 300 (79.3) 300 (79.3) 300 (79.3) 300 (79.3)"4"(S-)DSHG-04-2N4 300 (79.3) 300 (79.3) 300 (79.3) 300 (79.3) (S-)DSHG-04-2B4 300 (79.3) 300 (79.3) 300 (79.3) 300 (79.3)"40"(S-)DSHG-04-"7"2N40300 (79.3) 300 (79.3) 300 (79.3) 300 (79.3) (S-)DSHG-04-2B40 300 (79.3) 300 (79.3) 300 (79.3) 300 (79.3)300 (79.3) 300 (79.3) 300 (79.3) 300 (79.3)DSHG-04-2B7 300 (79.3) 300 (79.3) 300 (79.3) 300 (79.3)Notes:1. Max flow described above shown value at pilot pressure more than 0.8 MPa (120 PSI).2. Max. flow in the table above represents the value in the flow condition of P A B T (orP B A T) as shown in the circuit diagram right.In case the valve is used in the condition that either A or B port is blocked, the maximum flowdiffers according to a hydraulic circuit, therefore, please consult us for details.ABPTbaNo.11

Solenoid Controlled Pilot OperatedDirectional ValvesDSHG-06 / S-DSHG-06DIRECTIONALCONTROLSList of Standard Models and Maximum FlowThree PositionsSpring CentredPressure CentredGraphic SymbolGraphic SymbolA BSpool TypebaYPMaximum FlowL /min (U.S.GPM)AMaximum FlowL /min (U.S.GPM)BbaYTPVT10 MPa 16 MPa 25 MPa 31.5 MPa10 MPa 16 MPa 25 MPa 31.5 MPaModel Numbers(1450 PSI) (2320 PSI) (3630 PSI) (4570 PSI)(1450 PSI) (2320 PSI) (3630 PSI) (4570 PSI)410 (108) 310 (81.9)420 (111)(S-)DSHG-06-3C2 500 (132) 500 (132)(S-)DSHG-06-3H2 500 (132) 500 (132) 500 (132)500 (132) 500 (132)500 (132)Model Numbers"2"DSHG-06-3H3 500 (132) 500 (132) 500 (132) 500 (132)DSHG-06-3C3 500 (132) 500 (132) 460 (122) 370 (97.8)"3"310 (81.9)420 (111)(S-)DSHG-06-3H4 500 (132) 500 (132) 500 (132)500 (132)500 (132)310 (81.9)420 (111)500 (132) 500 (132) 500 (132)(S-)DSHG-06500 (132)500 (132)470 (124)500 (132) 500 (132) 500 (132)DSHG-06-3C5 500 (132) 500 (132) 425 (112) 350 (92.5)3H40500 (132)420 (111)DSHG-06-3C6 475 (125) 390 (103) 300 (79.3) 230 (60.8)DSHG-06-3H5 500 (132) 500 (132) 500 (132)500 (132)420 (111)(S-)DSHG-06-3C60 475 (125) 420 (111) 340 (89.8) 280 (74.0) (S-)DSHG-06-3H6 500 (132) 500 (132) 500 (132)500 (132)410 (108)500 (132)410 (108)(S-)DSHG-06-3C40 500 (132) 500 (132)500 (132)(S-)DSHG-06-3C4 500 (132) 500 (132)"4""40""5""6""60"DSHG-06-3C7 500 (132) 500 (132) 450 (119) 360 (95.1)"7"450 (119)500 (132)410 (108)(S-)DSHG-06-3C10 500 (132) 500 (132)500 (132)410 (108)DSHG-06-3C11 500 (132) 500 (132)500 (132)410 (108)(S-)DSHG-06-3C12 500 (132) 500 (132)500 (132)DSHG-06-3C9 500 (132) 500 (132)"9""10""11""12"500 (132) 500 (132) 500 (132) 500 (132)DSHG-06-360 (95.1)3H60500 (132)310 (81.9)(S-)DSHG-06-3H7500 (132)310 (81.9)DSHG-06-3H9500 (132)310 (81.9)(S-)DSHG-06500 (132)500 (132) 500 (132) 500 (132) 500 (132)460 (122)500 (132)460 (122)500 (132) 500 (132) 500 (132)500 (132)460 (122)500 (132) 500 (132) 500 (132)500 (132)500 (132) 500 (132) 500 (132)Two PositionsSpring OffsetNo-SpringGraphic SymbolGraphic SymbolASpool TypeBabYPMaximum FlowL /min (U.S.GPM)Maximum FlowL /min (U.S.GPM)BbYTModel NumbersAPT10 MPa 16 MPa 25 MPa 31.5 MPa Model Numbers(1450 PSI) (2320 PSI) (3630 PSI) (4570 PSI)10 MPa 16 MPa 25 MPa 31.5 MPa(1450 PSI) (2320 PSI) (3630 PSI) (4570 PSI)(S-)DSHG-06-2N2 500 (132) 500 (132) 500 (132) 500 (132) (S-)DSHG-06-2B2 500 (132) 500 (132) 500 (132) 500 (132)"2"DSHG-06-2N3 500 (132) 500 (132) 500 (132) 500 (132)"3"DSHG-06-2B3 500 (132) 500 (132) 500 (132) 500 (132)"4"(S-)DSHG-06-2N4 500 (132) 500 (132) 500 (132) 500 (132) (S-)DSHG-06-2B4 500 (132) 500 (132) 500 (132) 500 (132)"40"(S-)DSHG-062N40"7"500 (132) 500 (132) 500 (132) 500 (132) (S-)DSHG-06-2B40 500 (132) 500 (132) 500 (132) 500 (132)500 (132) 500 (132) 500 (132) 500 (132)DSHG-06-2B7 500 (132) 500 (132) 500 (132) 500 (132)Notes:1. The relation between max. flow and pilot pressure in the table above is as shownbelow.(Example)410 (108)Maximum flow rate is constant regardless of pilot pressure.500 (132)500 (132)Pilot Pressure more than 0.8 MPa (120 PSI).In case pressure centred models, pilot pressure is more than1 MPa (150 PSI).2. Max. flow in the table above represents the value in the flow condition of P A B T (or P B A T) as shown in the circuit diagram right.In case the valve is used in the condition that either A or B port is blocked, themaximum flow differs according to a hydraulic circuit, therefore, please consult usfor details.No.12Pilot Pressure at 0.8 MPa (120 PSI).In case pressure centred models, pilotpressure is more than 1 MPa (150 PSI)Pilot Pressure at 1.5 MPa (220 PSI).ABPTba

Solenoid Controlled Pilot OperatedDirectional ValvesDSHG-10 / S-DSHG-10DIRECTIONALCONTROLSList of Standard Models and Maximum FlowThree PositionsSpring CentredPressure CentredGraphic SymbolGraphic SymbolA BSpool TypebaYPMaximum FlowL /min (U.S.GPM)AMaximum FlowL /min (U.S.GPM)BbaYTPTV10 MPa 16 MPa 25 MPa 31.5 MPa10 MPa 16 MPa 25 MPa 31.5 MPaModel Numbers(1450 PSI) (2320 PSI) (3630 PSI) (4570 PSI)(1450 PSI) (2320 PSI) (3630 PSI) (4570 PSI)950 (251) 750 (198)970 (256)(S-)DSHG-10-3H2 1100 (291) 1100 (291) 1100 (291)(S-)DSHG-10-3C2 1100 (291) 1100 (291)1100 (291) 1100 (291)1100 (291)1050 (277)DSHG-10-3H3 1100 (291) 1100 (291) 1100 (291)DSHG-10-3C3 1100 (291) 1100 (291) 1060 (280) 895 (236)1100 (291)950 (251) 750 (198)970 (256)(S-)DSHG-10-3H4 1100 (291) 1100 (291) 1100 (291)(S-)DSHG-10-3C4 1100 (291) 1100 (291)1100 (291) 1100 (291)1100 (291)950 (251) 750 (198)970 (256)(S-)DSHG-101100 (291) 1100 (291) 1100 (291)(S-)DSHG-10-3C40 1100 (291) 1100 (291)1100 (291) 1100 (291)1100 (291)1000 (264)3H401100 (291) 1100 (291) 1100 (291)DSHG-10-3C5 1100 (291) 1100 (291) 980 (259) 850 (225)1100 (291)970 (256)DSHG-10-3H5 1100 (291) 1100 (291) 1100 (291)DSHG-10-3C6 1050 (277) 880 (232) 700 (185) 570 (151)1100 (291)970 (256)(S-)DSHG-10-3C60 1050 (277) 940 (248) 785 (207) 680 (180) (S-)DSHG-10-3H6

SOLENOID CONTROLLED PILOT Up to 31.5 MPa (4570 PSI), 1100L/min (291 U.S.GPM) Pub. EC-0404 PILOT OPERATED DIRECTIONAL VALVES OPERATED DIRECTIONAL VALVES . Pilot Drain Port for Solenoid Controlled Pilot Operated Directional Valve Avoid connecting the valve pilot drain port to a line with

Related Documents:

S - 5,20 bar (75 psi) check Solenoid Energization Identity Blank - Standard arrangement for ANSI B93.9 (i.e. energize solenoid A to follow flow P to A). V - Solenoid identification determined by position of solenoid (i.e. solenoid A at port A end/solenoid B at port B end). Note 4 and 8 type spools are always V. Solenoid

LVM09/090 2/3 port direct operated solenoid Cv 0.018 139 LVM10/100 2/3 port direct operated solenoid Cv 0.03 0.04 139 LVM15/150 & -20/200 2/3 port direct operated solenoid valve Cv 0.015 0.065 140 VDW10, -20 & -30 2/2 solenoid Cv 0.03 0.44 141 VDW200 & -300 3/2 solenoid Cv 0.03 0.44 142 VCA solenoid valve Cv 0.33 2.1 143 N

Solenoid Controlled Pilot Operated Directional Valves Solenoid Controlled Pilot Operated Directional Valves These valves are composed of a solenoid operated pilot valve and a pilot operated slave valve. When a solenoid is energised the pilot valve directs the flow to move the spool of the slave valve, thus changing the direction of flow in the .

Manual 36541 Solenoid Troubleshooting Guide Woodward 1 Chapter 1. General Information Solenoid Operation Single Coil Solenoid A solenoid is a device that converts electrical energy into mechanical force. The basic single coil solenoid is made of a free moving steel plunger that sits within a wound coil of copper wire.

3X2, 5X2 SINGLE SOLENOID VALVE WITH SPRING RETURN PRODUC T IM A GE SYMBOL 5 3 4 2 1 1 3 2 3X2, 5X2 DOUBLE SOLENOID VALVE PRODUC T IM A GE SYMBOL Function Symbol DOUBLE SOLENOID DOUBLE SOLENOID Model SDA1BN23CT060V0 SVA1BN23CT060V0 1 - Input, 2/4 - Output, 3/5 - Exhaust Port Size IN OUT EXH 1200 LPM at 6 Bar Flow ¼" ¼" ¼" 1200 LPM at 6 .

135.5 147.5 Solenoid operated MFS-O2 ORDERING CODE Solenoid operated modular type. FNC G 0 2 * * * One-way controlled FNC. THF Valve size Voltage for coil Cam operated FKC or Roller operated FYC Controller type of FKC Solenoid controlled FSC. SF. SDF Solenoid modular MFS. FSC-O2 FSC-O3 MFS-O3

STC Installation and Operation Procedure 3V120-3V420 & 4V120-4V420 Solenoid Valves 4V120-4V420 (4 way valve) SOLENOID VALVE POSITION 1 2 Operations: 1. When Solenoid is OFF (Position 1), Port P is connected to Port A. Port B is connected to Port EB. 2. When Solenoid is ON (Position 2), Port

Although adventure tourism is recognized as an important, growing tourism segment, primary research to quantify the size and scope of this market in the U.S. or internationally (Schneider 2006) has been lacking. For this reason, George Washington University, along with its partners, the Adventure Travel Trade Associ-ation (ATTA) and Xola Consulting, sought to better understand the adventure .