Online Data - Procomps

1y ago
5 Views
1 Downloads
4.39 MB
16 Pages
Last View : 21d ago
Last Download : 2m ago
Upload by : Macey Ridenour
Transcription

alignment locksperformance testingProgressive Components regularly tests products through independent testingfacilities nationwide.Before launching of the Z-Series Alignment Locks, Progressive contracted ElementMaterials Technology to provide a thorough mold lock Performance Evaluation:“Element Materials Technology has conducted independent life cycle testing of moldinterlocks since 1999. The processes with fixtures and cycling were establishedto simulate use in the molding environment, but more severe loads were used toaccelerate the failures at 4400 lbs of pressure. The locks tested have been fromProgressive as well as other standard lock distributors in the US and Asia, plus severaladditional material and treatment combinations were tested for comparison.”It was determined that the Progressive Components’ Z-Series Alignment Locksexceeded the 2-million cycle mark, and still displayed no measurable signs of wearof any type.“During the past year, over 21 different tests were performed with the purpose of cyclinguntil failure occurred. At no time during our tests over the years have we seen cycleperformance at the level of this new design, represented as PRO in the chart below.”With the industry’s widest selection of sizes in stock and competitively priced, specifying alignment locks fromProgressive Components means your molds will have unmatched protection from damage and downtime.online dataalignment lockstop locksRCZz-seriessDS2WS1CAD insertion pointFemale: m D-2 h Core: 58-62 HRC, Surface: 80 HRCm H-13 h Core: 42-48 HRC, Surface: 70 HRCMale: .000-.002 .0000-.0004 .000-.002 .000-.002bc.5001.000.500.375.30Learn more at www.procomps.com/z-seriesInch Standardds1s2 .01PocketRadiusChamfer.375.25.688.188.03M: #6-32 x 1/2”F: #6-32 x 5/8”F: #6-32 x 3/4”.0001/.0003Clearance Per Side.438 .01.312rzshcs1.250.625.500.41.875.250.03M: #6-32 x 5/8”.7501.250.625.500.38.438.375.875.250.04M: #8-32 x 5/8”F: #8-32 x 0.04M: #8-32 x 7/8”F: #8-32 x 1”1.0001.500.875.375.57.500.5001.000.250.04M: #10-32 x 1/2”F: #10-32 x 75.04M: #10-32 x 7/8”F: #10-32 x 5.375.04M: 1/4-20 x 0.500.04M: 1/4-20 x 7/8”F: 1/4-20 x 750.375.04M: 1/4-20 x 3/4”F: 1/4-20 x 250.500.06M: 5/16-18 x 1”TL200X3502.0003.5001.750.7501.071.5001.000 2.500.500.06M: 3/8-16 x 7/8”F: 1/4-20 x 1”F: 5/16-18 x 1-1/4”F: 3/8-16 x 2”All catalog pages are online for forwarding totwabcrdsszshcssuppliers,customers,etc.Screws included.Metric Standardcatalognumber .00-.05 .00-.01 .00-.05 .00-.05.002/.008Clearance Per Side1 .252 .25PocketRadiusChamferTLM26X3526352381M: M5 x 16F: M5 x 25TLM30X45304525151715153081M: M6 x 18F: M6 x 25TLM36X553655302021.5201837.581M: M8 x 22F: M8 x 35TLM36X75367535202630185281.5M: M10 x 25F: M10 x 35TLM45X100451006020424022.57081.5M: M10 x 25F: M10 x 65XUS Patent No. 8,821,144 and others pending.aTL100X150TL75X125.625ws Salt Bath NitridecatalognumberTL50X100TL62X125ts Titanium Nitride Coated25151711Screws included.Note: 500 F max operating temperature.For custom Locks, refer to the templates in section X.Additional Option:R (4)Top Locks are also available with dual radii formounting internally. To order, specify the catalognumber followed by ”-R”. Ex. TL112X200-R.13View the entire independent testingreport online.C-1

alignment locksalignment locksz-series Progressive’s Alignment Locks have been advanced to outperform otherstyles. This is achieved through a combination of engagement geometry,particulate capturing rings, materials and treatments, and lubrication.Benefits of the Z-Series Alignment Locks include: Longevity that far surpasses others, confirmed by extensiveindependent lab testing as well as monitoring performance inharsh, ‘real world’ conditions. Exclusive features maintain clean and consistent lubrication. Bar Lock, Guide Lock, Side Lock, X-Style Side Lock and Top Lockstyles available.BFCCDEAAEngagement Ramp: A fine finish radial lead-in for smooth lifting upon engagement of the mold halves.BParticle Rings: Particle rings on the width of the male locks trap material and debris to avoid“picking up” or galling of the alignment surface.CLonger Engagement: Using the maximum allowable engagement area on all locks surpasses previously-establishedindustry standards.DArced Relief: Reduces the possibility of parts sticking to the lock at the bottom of the mold.ERounded Edges: A larger radius for all protruding surfaces to eliminate operator “reach in” injury.FPry Slot Lead-In: Expanded the entry of pry slots to ease removal.GPremium Materials: Males: H-13, 42-48 HRC, Surface: 70 HRC; Females: D-2, 58-62 HRC, Surface: 80 HRC.C-2US Patent No. 8,821,144 and others pending.

side locksWDz-seriesTRZS3BHCAS2Female: m D-2SHCSS1Male:h Core: 58-62 HRC, Surface: 80 HRC s Titanium Nitride Coatedm H-13 h Core: 42-48 HRC, Surface: 70 HRC s Salt Bath NitrideCAD insertion pointcatalognumberInch Standardtwa .000-.002b .000-.002cd.0001/.0003Clearance Per Sideh .000-.004rs1/s2/s3z .01Chamfershcs.187.250.015#10-32 x 1/2”.187.250.03#8-32 x 5/8”.250.03#8-32 x 5/8”.312.03#10-32 x 5/8”.375.031/4-20 x 3/4”.033/8-16 x 1” .000-.002 51.3751.752.0004.250.500.625.031/2-13 x 0.500.625.031/2-13 x 1-1/2”Screws included. .000-.002 .0000-.0004 .000-.002 8catalognumbertwadhInch Standard-Compatible.0001/.0003Clearance Per Side .000-.004PocketRadiusrs1s2 s3 .01 .01Chamfershcs.5001.74.187.281.281.437.031/4-20 x 3/4".6801.74.187.375.375.437.031/4-20 x 3/4"1.0002.73.187.375.688.688.03 .01z3/8-16 x 1"Screws included.XMetric StandardXcatalognumbertwabcdhr .00-.05 .00-.01 .00-.05 02/.008Clearance Per Side 0.0- 0.1PocketRadius131743522.525725For custom Locks, refer to the templates in section X.s1s2/s3zshcs .25Chamfer811.8M6-1.0 x 1812.518.8M10-1.5 x 201522.8M10-1.5 x 2020.522.8 .25M10-1.5 x 25Screws included.Note: 500 F max operating temperature.XLubrication: Non-drying, non-hardening food grade grease is applied to all areas, including the particle rings.X For production, install the locks and wipe down the outside of the Side Locks only; maintain the grease on the mating surfaces and within the rings.C-3US Patent No. 8,821,144 and others pending.

alignment lockstop locksz-seriesRCZDS2WS1CAD insertion pointFemale: m D-2h Core: 58-62 HRC, Surface: 80 HRCm H-13 h Core: 42-48 HRC, Surface: 70 HRCMale:twas Titanium Nitride Coateds Salt Bath Nitridebcds1catalognumber .000-.002 .0000-.0004 25.6251.250.625.500.41.438.312 .000-.002.0001/.0003Clearance Per Side .01Inch Standards2rzshcsPocketRadiusChamfer.688.188.03M: #6-32 x 1/2”F: #6-32 x 5/8”.875.250.03M: #6-32 x 5/8”F: #6-32 x 3/4”F: #8-32 x 3/4” M: #8-32 x 0.04M: #8-32 x 7/8”F: #8-32 x 0.04M: #10-32 x 1/2”F: #10-32 x 75.04M: #10-32 x 7/8”F: #10-32 x 5.375.04M: 1/4-20 x 3/4”F: 1/4-20 x 500.04M: 1/4-20 x 7/8”F: 1/4-20 x 750.375.04M: 1/4-20 x 3/4”F: 1/4-20 x 250.500.06M: 5/16-18 x 1”F: 5/16-18 x 1-1/4”TL200X3502.0003.5001.750.7501.071.5001.000 2.500.500.06M: 3/8-16 x 7/8”F: 3/8-16 x 2”Screws included.XXcatalognumbert .00-.05wab .00-.01 .00-.05 .00-.05Metric Standardcds1s2rz.002/.008Clearance Per Side .25 381M: M5 x 16F: M5 x 25TLM30X45304525151715153081M: M6 x 18F: M6 x 25XTLM36X553655302021.5201837.581M: M8 x 22F: M8 x 35TLM36X75367535202630185281.5M: M10 x 25F: M10 x 35451006020424022.57081.5M: M10 x 25F: M10 x 65XTLM45X100XScrews included.Note: 500 F max operating temperature.Note: For 20mm square size, refer to page C-11.For custom Locks, refer to the templates in section X.XAdditionalOption:XTop Locks are also available withdual radii for mounting internally.To order, specify the catalognumber followed by ”-R”.Ex. TL112X200-R.R (4)Lubrication: Non-drying, non-hardening food grade grease isapplied to all areas, including the particle rings. For production, install the locks and wipe down theoutside of the Top Locks only; maintain the greaseon the mating surfaces and within the rings.C-4US Patent No. 8,821,144 and others pending.

guide locksz-seriesLLSSMSFSTWRHC1/2 CZRFemales (2): m D-2h Core: 58-62 HRC, Surface: 80 HRCm H-13 h Core: 42-48 HRC, Surface: 70 HRCMale:Inch StandardcatalognumberGL100X150s Titanium Nitride Coateds Salt Bath NitrideCAD insertion point .000-.010l .0003 .0006w .0000-.0003c .000-.005f .0000-.0003tm1.0001.500.500.500.500hsrzshcs .00-.01 .01PocketRadiusChamfer.375.85.25.187.03M: #10-32 x 1”F: #10-32 x .250.06M: 1/4-20 x 1-1/2”F: 1/4-20 x 4.375.06M: 3/8-16 x 2”F: 3/8-16 x 1.56.500.09M: 1/2-13 x 2-1/4”F: 1/2-13 x 1-1/2”Screws included.MetricStandardXcatalognumberXl .00-.25w .008 .015c .00-.01f .00-.12tm .00-.01h .0-.2s 41M: M4 x 25F: M4 x 14GLM40X65X406520202515341091.5M: M5 x 35F: M5 x 22GLM50X90509025254020441091.5M: M6 x 45F: M6 x 30XNote: 500 F max operating temperature.For custom Locks, refer to the templates in section X.AdditionalOption:XR (4)XR (2) Guide Locks are also availableEach with dual radii for mountinginternally as shown at left.To order, specify the catalognumber followed by ”-R”.Ex. GL200X350-R.Lubrication: Non-drying, non-hardening food grade grease isapplied to all areas, including the particle rings. For production, install the locks and wipe down theoutside of the Guide Locks only; maintain the greaseon the mating surfaces and within the rings.C-5US Patent No. 8,821,144 and others pending.

alignment locksx-style side locksz-seriesAAXP.03 x 45 RCWDSSHCSSTXFemales (2): m D-2Male:Xh Core: 58-62 HRC, Surface: 80 HRCm H-13 h Core: 42-48 HRC, Surface: 70 HRCtwxs Titanium Nitride Coateds Salt Bath NitrideacdrspCAD insertion pointcatalognumber .000-.002 .0000-.0004 .000-.002 .000-.002 .01.0001/.0003Clearance Per SidePocketRadius .01 .312.250#10-32 x 375.3131/4-20 x 5.3131/4-20 x 500.3753/8-16 x 1”XXFor custom Locks, refer to the templates in section X.Screws included.Note: 500 F max operating temperature.Xshuttle mold setsXExamples of Shuttle Mold configurations:2 Female Inserts : 1 Male InsertTo order, specify “-SF” after the catalog number of the lock.Example: SL50X200-SF GL100X150-SF TL75X125-SF2 Male Inserts : 1 Female InsertTo order, specify “-SM” after the catalog number of the lock.Example: SL75X300-SM GL250X450-SM TL112X200-SMContact Customer Service for Pricing at CustomerService@procomps.comC-6US Patent No. 8,821,144 and others pending.

inserted bar locksz-seriesProgressive’s Inserted Bar Locks are engineered for long term alignment of very large molds: Longevity that far surpasses others, confirmed by extensive independent labtesting as well as monitored performance in harsh, ‘real world’ conditions. Designed to align large injection molds up to 75,000 pounds(B-Side and platen). Inserts are also sold individually for new tooling or to retrofit onto existing molds.LBar: m 4140 h Core: 36-40 HRC s Black Oxidetw1Inserts: m H-13 h Core: 42-48 HRC, Surface 70 HRC s Salt Bath Nitridew2S3catalognumber .000- .005 .0000- .0005BLN150L81.5004.000 .000/-.002BLN250L102.5005.000 .000/-.002BLN350L133.5006.000PWbar lock 10.38 5.001.25N3.253.251.504.003.50l .01 .01W14.000R5.0006.000 .000/-.003Ts3 .01W212.886.00rCAD insertion pointpshcstotalmax lbs.supported4.001/2-13 x 1.7525,0001.005.385/8-11 x 2.7550,0001.006.883/4-10 x 3.7575,000PocketRadiusPWMinimumPocket LengthNote: Each catalog number includes (1) Bar and (2) Inserts with screws. Guides are sold separately.guidesbarLPW2CW1 S3PWW2PW.315Insert PocketRInsertsS1S2InsertsTLS5NL.375S6m D-2CS4h Core: 58-62 HRC, Surface: 80 HRC s Titanium Nitride CoatedcatalognumberEt .000- .005BLG150L2.3 1.500.315 1.500BLG150L3.8Insert PocketBLG250L4.3 2.500BLG350L4.8 3.500Tlpwc .000- .005 .0010 .0015 01.0001.0001.2501.750NHeREF.31.31.31.31s4 .01S7s5 .01shcs.50 1/4-201.50SHCS 3/8-16 x 1.75(2) OnCenterx 1.75.50 BLS1502.503/8-16BLS250/350 (4).6253.00 1/2-13 x 2.75.8753.25 5/8-11 x 3.75 LN350L13Notes: Guides are sold in pairs. Each catalog number includes (2) Guides and (4) screws. 500 F max operating temperature.NLS6 .0000.375 -.0005S7m H-13 h Core: 42-48 HRC, Surface 70 HRC s Salt Bath NitridecatalognumberBLS150BLS250BLS350NH1/4-20 SHCSBLS150 (2) On CenterBLS250/350 (4)nhinserts .000- .005 .000- 3.000--1.5002.500 .01 .01Note: Inserts sold individually and include screws.C-7US Patent No. 8,821,144 and others pending.

alignment locksbar locksz-series-inch standardProgressive’s Bar Locks enable mold designers to select off-the-shelfcomponents for alignment of large molds and molds with multiplemoving plates.Long-term precision alignment of plates is achieved throughProgressive’s Z-Series proprietary treatments, engagement rampgeometry and particle rings on the guiding surfaces.Non-drying, non-hardening food grade grease is applied to all areas,including the particle rings. For production, install the locks and wipedown the outside of the Bar Locks only; maintain the grease on themating surfaces and within the rings.Xbarm H-13 h Core: 42-48 HRC, Surface: 70 HRC s Salt Bath NitrideXtcatalognumber .000- .005XBLB100L61.000 .005 .0000- .0005wREFep6.001.000.221.38ls1s2 .005 .005shcs.38.695/16-18 x 1.25BLB125L9X1.2508.881.500.281.88.501.003/8 - 16 x 1.50BLB137L111.37510.882.000.312.38.501.383/8 - 16 x 1.50BLB150L16X1.50015.883.000.313.38.632.001/2 - 13 x 1.75Note: Sold individually. Each catalog number includes (1) Bar Lock and (2) Screws.XCAD insertion pointFor custom Bar Locks, refer to the templates in section X.barguidesLXEXWPWS2S1TPguidesm D-2h Core: 58-62 HRC, Surface: 80 HRC s Titanium Nitride 3.8t .000- .0051.0001.2501.3751.500l .000- .0051.3101.8101.3102.3101.8103.3102.3103.810cpwes3 .0000- .0003 .0003 .0006REF 751.0005.000.31.500Xs4 .005.7501.125.7501.251.1252.2501.5002.500Guides are sold in pairs. Each catalog number includes (2) guides and (4) screws.Note: 500 F max operating temperature.Xshcsuse with#10-32 x 1.25BLB100L61/4-20 x 1.50BLB125L95/16-18 x 1.50BLB137L113/8-16 x 1.75BLB150L16LS4S3CETCAD insertion pointguidesFor custom Guides, refer to the templates in section X.XC-8XUS Patent No. 8,821,144 and others pending.

bar locksz-series-metric standardbarm H-13 h Core: 42-48 HRC, Surface: 70 HRC s Salt Bath Nitridetcatalognumber .0BLBM25L12525 .1 .00- .01REFMINps1s2 .1shcs125256361018M8-1.25 x 30wl- .1e .1BLBM32L160321603864612.525M10-1.5 x 35BLBM38L25038250508561530M12-1.75 x 45CAD insertion pointNote: Sold individually. Each catalog number includes (1) Bar Lock and (2) Screws.barguidesLEWPWS2S1TPLS4m D-2S3CXh Core: 58-62 HRC, Surface: 80 2L46XTXXXXBLGM38L76guides253238l .0- .1273636464676cpw124916702294 .000- .005 .007 .015eREFs3 .166811s4 .1142020302454shcsuse withM4-0.7 x 25BLBM25L125M6-1.0 x 35BLBM32L160M10-1.5 x 40BLBM38L250Guides are sold in pairs. Each catalog number includes (2) guides and (4) screws.Note: 500 F max operating temperature.For custom Guides, refer to the templates in section X.US Patent No. 8,821,144 and others pending.XBLGM38L46t .0- .1guidess Titanium Nitride CoatedC-9

alignment locksbar locksapplicationsStripper Plate ApplicationPThree Plate ApplicationPMINIMUM POCKET LENGTH PStack Mold ApplicationLarge Mold ApplicationC-10US Patent No. 8,821,144 and others pending.

side/top/guide lock selection guideRefer to the chart below to match the correct alignment lock for the corresponding mold size and weight of B-Side and press platen, using fourlocks per mold. Clean and lubricate lock every 100,000 cycles, and prevent corrosion during mold storage.RECOMMENDEDMAX MOLD SIZE(LXWXH)SIDE LOCKSMETRIC SIDE LOCKSGUIDELOCKSTOP LOCKSTOTAL MAX WEIGHTB SIDE PRESS PLATEN(LBS/KG)RTI AND MOLDS8 X 8 X 8 ANDSMALLERSL37X100, SL50X125SL50X150, SL50X200SLS62X150, SLS62X200SLR50X125,SLR50X150SLM16X50, SLPM16X20SLPM16X40, SLPM20X25SLPM20X50, SLMS13X38SLMS16X50GL100X150GLM25X45TL50X100, TL62X125TL75X125, TLM26X35TLR87X1502,000 / 90011 X 16 X 10SL50X125, SL50X150SL50X200,SLS62X150SLS62x200, SLS75X300SLS75X400, SLR50X150SLR50X200SLM16X50, SLMS19X75SLPM25X32, SLPM25X63SLPM32X40, 50X250GLM25X45TL62X125, TL75X125TLM26X35TLR87X150TLR112X2005,000 / 2,30016 X 24 X 16SL50X150, SL50X200SL75X300, SLS112X500SLS75X300, SLS75X400SLR75X300, SLR100X400SLM19X75, 40X65TL75X125, TL87X150TLM26X35, TLM30X45TLR112X200TLR150X2507,000 / 3,20028 X 34 X 24SL75X300, SLS112X500SLM19X75, SLM19X100GL200X350GL150X250GLM40X65TL100X150, TL100X200TL112X200, TL112X300TLM26X35, TLM30X4510,000 / 4,50032 X 40 X 28SL100X400SLM25X125GL200X350GLM40X65TL112X200, TL112X300TLM36X55, TLM36X7515,000 / 6,80042 X 48 X 34SL125X500GL250X450GLM50X90TL150X250, TL175X300TLM36X55, TLM36X7520,000 / 9,00048 X 52 X 38SL150X600GL250X450TL175X300, TL200X350TLM45X10026,000 / 11,800bar lock selection guideBARCATALOG NUMBERGUIDECATALOG NUMBERBAR LOCKENGAGEMENTTOTAL MAX WEIGHTSUPPORTED (LBS/KG)BLB100L6BLG100L1.3, BLG100L1.84.5015,000 / 6,800BLBM25L125BLGM25L27, BLGM25L368915,000 / 6,800BLB125L9BLG125L1.3, BLG125L2.37.0020,000 / 9,000BLBM32L160BLGM32L36, BLGM32L4611420,000 / 9,000BLB137L11BLG137L1.8, BLG137L3.38.5023,000 / 10,400BLBM38L250BLGM38L46, BLGM38L7619426,000 / 11,500BLB150L16BLG150L2.3, BLG150L3.812.5026,000 / 11,800BLN150L8BLG150L2.3, BLG150L3.83.7525,000 / 11,250BLN250L10BLG250L4.35.0050,000 / 22,500BLN350L13BLG350L4.86.0075,000 / 34,000C-10aUS Patent No. 8,821,144 and others pending.

taper locksMalem H-13 h 48-52 HRCODo.d. .0000-.00031/2Li.d.312CAD insertion 1-1/2Taper /16ID3/4male .004 d below)taper lock platesFemalem AISI 52100 h 57-61 HRC s Black OxideT59 2 HRCDdtcatalognumberTaperLockOD .000-.015 .000-.002Flat 505/16-18TLP20022.187.2505/16-181/2” long FHCS included.top lock-20mm squarez-seriesZRCDFemale: m D-2Male:h Core: 58-62 HRC, Surface: 80 HRCm H-13 h Core: 42-48 HRC, Surface: 70 HRCtwabcatalognumber .00-.05 .00-.01 .00-.05 .00-.05TLM20X2020201414s Titanium Nitride CoatedWS1M6 threadfor lockremovalS2ABTs Salt Bath Nitridec7d.002/.008Clearance Per Side9rs1s2 .25PocketRadiusChamferCenterCenter51 .25zshcsM: M4 x 2580 HRCC65 HRC59 1HRCRF: M4 x 10C-11

alignment locksside locksneedle bearing inch standard WDRTS3.02 x 45 ChamfersS4BE57 1HRCCH57 1HRCAS2S1m O-2 h 56-58 HRC s Black Oxidetwcatalognumber .000-.005 .0002wabPocketWidth .0005-.0000 .000-.005 .000-.005SHCS (4)cdeh .000-.004CAD insertion pointrPocketRadiuss1 s2 s3 s4 .01 .01 .01 02.250.187.171.250.171.437#8-32 x .750.187.250.250.250.250#8-32 x 502.250.187.182.376.182.500#8-32 x 2.250.187.312.312.312.312#10-32 x 52.750.250.375.375.375.3751/4-20 x 5.4503.750.500.500.500.500.5003/8-16 x 1-1/8”Screws included.For technical information, refer to page C-13. Note: Cages are manufactured from resin or aluminium, depending on size.needle bearing metric standard WDRS2E57 1HRCS3HS2S1m O-2 h 56-58 HRC s Black OxidewC57 1HRCAw.5 x 45º ChamfersS3BtTaSHCS (4)catalognumber .00-.12 .005PocketWidth .012- .000 .00-.12 .00-.12bcde 066663633hPocketRadiusrs1s2s3 .25shcs12.192891135M8-1.25 x 3519.513210131848M12-1.75 x 45 .25For technical information, refer to page C-13. Note: Cages are manufactured from resin or aluminium, depending on size. .25Screws included.C-12US Patent No. 6,953,331

top locksneedle bearing inch standard 57 1 HRC.02 x 45 ChamfersBECDAS2SHCS (4)T57 1 HRCS1RWm O-2 h 56-58 HRC s Black OxidetwCAD insertion pointcatalognumber .000-.005 .0002-.0000PocketWidth .0005-.0000w .000-.005a .000-.005bcdes1s2 6.550.225.4381.143.250M: #8-32 x 25.5631.375.375M: 1/4-20 x 3/4” F: 1/4-20 x .400.7501.750.375M: 1/4-20 x 3/4” F: 1/4-20 x .015.350.7501.875.375 .01Note: Cages are manufactured from resin or aluminium, depending on size.rshcsM: 1/4-20 x 1”F: #8-32 x 1-1/2”F: 1/4-20 x 2”Screws included.Technical Information: Zero clearance between male and female (D) dimensions. Bearings: 64 HRC Maximum Mold Temperature: 300 F (150 C) Engagement occurs at E dimension shown. Locks are to be mounted in the mold base and not in the core or cavity inserts. For optimal performance, pockets are to be machined to nominal “W” pocket width dimensions in each table. If replacing locks in existingpockets, ensure .0004” clearance, and the lock may be modified to suit. As with other mold mechanisms, clean and maintain locks at the mold’s scheduled PMs.C-13US Patent No. 6,953,331

alignment locksside locksinch standardDX50-55 HRCS1BHCAS2S355-60 HRCSHCSTWFemale: m O-2m O-2Male:catalognumberZh 55-60 HRCh 50-55 HRCtCAD insertion pointwab .000-.002 .0000-.0004 .0000-.0008 2.000.870.870c.0001/.0003Clearance Per Sided .000- .002hCornerChamferxzs1 .01s2s3Chamfer .01shcs.33.5001.74.19.02.437.281.2811/4-20 x 3/4”.33.6801.74.19.04.437.375.3751/4-20 x 3/4” 688.688.3753/8-16 x .875.875.6253/8-16 x 04.875.875.7501/2-13 x 1-1/4”Screws included.metric standardcatalognumbertwabc .00-.05 .00-.01 .00-.02 X38dhxzs1/s2 s3 .2 .2shcs78M5-.8 x 15.002/.008Clearance Per Side .00- .04CornerChamferChamfer12445.59.5174351118M6-1.0 x 18152572811812.5M10-1.5 x 202135901012215M10-1.5 x 202145901012220.5M10-1.5 x 25Screws included.C-14

side locksgraphite pluggedRH -.5-.7S2H -.5-.7LS1Dg5SWg4S2S1T .0-.1T .0-.1CZm O-2.5mmCAD insertion pointh 56-60 112dtwchs1s2srzScrew Size16204011227152661M6-1.0 x 2520224513277193161M6-1.0 x 2525255014369273581M6-1.0 x 30323263194611354581M8-1.25 x 354036852256154060101.5M10-1.5 x 4050401002466184874101.5M12-1.75 x 45Screws included.Using grease will inhibit the function of the graphite plugs. Instead, use a light 20 weight oil at startup to begin lubrication.C-15

A Engagement Ramp: A fine finish radial lead-in for smooth lifting upon engagement of the mold halves. B Particle Rings: Particle rings on the width of the male locks trap material and debris to avoid "picking up" or galling of the alignment surface. C

Related Documents:

807 Katherine Golf Club YES ONLINE 808 Palmerston G & CC YES ONLINE 809 RAAF Darwin GC YES ONLINE 810 Tennant Creek GC YES ONLINE 811 RAAF Tindal GC YES ONLINE 812 Elliott GC YES ONLINE 20010 National Assoc Left-handed Golfers - NSW YES ONLINE 20011 The Sydney Veteran's Golfers Assoc. YES ONLINE

When asked if the online course(s) taken in 2010 was fully online, spring partially online, or both fully online and partially online, the majority of students who responded reported their course(s) online onlyas (77%). (See Table 2.) This was similar to fully online course enrollment by the general online population (76%).

Title: ER/Studio Data Architect 8.5.3 Evaluation Guide, 2nd Edition Author: Embarcadero Technologies, Inc. Keywords: CA ERwin data model software Data Modeler data modeler tools data modelers data modeling data modeling software data modeling tool data modeling tools data modeling with erwin data modelings data modeller data modelling software data modelling tool data modelling

neric Data Modeling and Data Model Patterns in order to build data models for crime data which allows complete and consistent integration of crime data in Data Warehouses. Keywords-Relational Data Modeling; Data Warehouse; Generic Data Modeling; Police Data, Data Model Pattern existing data sets as well as new kinds of data I. INTRODUCTION The research about Business Intelligence and Data

ArcGIS Online: Map Viewer 6 9/28/2021 Step 1 -Find/Upload Layer - Find existing data shared by others on ArcGIS Online - Upload your data to ArcGIS Online (e.g CSV File) - Create maps in ArcGIS Pro and upload it to ArcGIS Online - In general, the data needs to be either already available in ArcGIS Online platform or you need to upload data to it.

Online shopping market by sector. 3 : 2.3 Online shopping market by product category 5 2.4 . Leading retailers in the online shopping market : 6 . 2.5 Forecasts of the online shopping market 7 2.6 : Consumer use of online shopping services . 7 : 2.7 Online non-food shopping market 8 2.8 . Online grocery shopping market: 10 . 2.8.1

3 Examples of Blended Learning Put assessments/reviews online Online discussions Online labs Put reference materials on Web Deliver pre-work online Provide office hours online Use mentoring/coaching tool Access experts live online Myth #8: People learn more in face-to-face settings than blended or fully online ones. Fully Online and Blended Learning Advantages

Stuart Russell and Peter Norvig, Artificial Intelligence: A Modern Approach(3rd Edition) (Pearson, 2009). For . Russell’s warnings, see John Bohannon, “Fears of an AI Pioneer,” Science349, 2015. Artificial Intelligence and Deterrence: Science, Theory and Practice . STO-MP-SAS-141 14 - 3 . To this end, AI is a field of science that attempts to provide machines with problem-solving .