ELECTRIC BICYCLE METER KT—LCD3 Product User Manual
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualContentsPreface . . 4Outlook and Size . 4MeterDimension 4Button Box Dimension . 4Main Material and Color . . 5Wiring Schematic . . 5Installation Instruction . . 5Φ 31.8 handlebar diameters install icon . . 5Φ 22.2 handlebar diameters install icon . . . 5Physical installation icon. 6Function Overview . . 6Display Content . . . 6Button Definition . . . 7Normal Operation . 7On/Off . 7Display Interface . . . 8Display 1 . . 8Display 2 . 9Display 3 . . 10PAS Ratio (or Handlebar) Gear Switch . . 11Push Function . 11Cruise Function . 12Turn On/Off Backlight . . 12Battery Capacity Indicator . . 13Motor Power and Temperature . 13Environment Temperature . 14Single Data Clearing . 15-1-
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualAutomatic Prompt Interface . . 15Error Code Display . . 15Motor Operating Temperature Alarm . 15User Project Setting . 16General Project Setting 16Maximum Trip Speed . 16Wheel Diameter . . 17Metric and Imperial Units . 18Exit General Project Setting . 18P Parameter Setting . . 19P1 Motor Characteristic Parameter Setting Mode . 19P2 Wheel Speed Pulse Signal Setting Mode . 19P3 Power Assist Control Mode . 20P4 Handlebar Startup Mode . 21P5 Power Monitoring Mode . 21Exit P Parameter Setting . 22C Parameter Setting . 23C1 Power Assist Sensor and Parameter Selection Mode . 23C2 Motor Phase Classification Coding Mode . 23C3 Power Assist Ratio Gear Initialization Mode. 24C4 Handlebar Function Setting Mode . 25C5 Controller Maximum Current Adjustment Mode . 26C6 Backlight Brightness Adjustment Mode . 27C7 Cruise Function Setting Mode . 27C8 Motor Operating Temperature Display Mode . 28C9 Power-on Password Setting Mode . 29C10 Automatic Restore Default Setting Mode . 30C11 Attribute Selection Mode . 31C12 Controller Minimum Voltage Adjustment Mode . 32Exit C Parameter Setting. 33-2-
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualParameter Copy . 33User Setting Note . 35Version Information 35-3-
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualPrefaceThe illustrated manual will help you understand and be familiar with the meterfunction, guiding you on how to operate the meter, how to set the project parameters, howto achieve the best match of the three as motor, controller and meter to improve electroniccontrol performance of the electric motor. This manual covers installation, operation,parameter setting of the meter and how to use it properly, which help you resolve theproblems appeared in practical use.Outlook and Size Meter DimensionMeter DimensionDual Bracket Mounting Dimension Button Box Dimension-4-
ELECTRIC BICYCLE METER KT—LCD3 Product User Manual Main Material and ColorPC material is mainly used for KT-LCD3 meter and button box housing, and thehousing color is dark gray or white. Wiring SchematicInstallation InstructionThe meter body and button box are mounted on the handlebars of the electric vehicle,adjusting perspective. In the case that the vehicle is power off, the meter connectors are inplug connection to corresponding controller connectors. Turn on the power, electricvehicle and meter will be under normal operation, the meter installation is finished. Theprotection film on meter display panel should be torn. Φ 31.8 handlebar diameters install icon Φ 22.2 handlebar diameters install icon-5-
ELECTRIC BICYCLE METER KT—LCD3 Product User Manual Physical installation iconFunction OverviewKT-LCD3 meter provide you with a variety of functions such as vehicle controls andvehicle status digitized displays to meet the trip demands. Trip time display (with displays of a single trip time (TM) and total trip time (TTM)); Trip speed display (with displays of real-time speed (Km/H or MPH) and a singlemaximum speed (MXS) and a single average speed (AVS)); Trip distance display (with displays of a single trip distance (DST) and total tripdistance (ODO)); Power assistant ratio (or handlebar) gear (ASSIST) switch; 6Km/H power assistant push () function; Cruise function (CRUISE); Battery capacity indicator (); Real-time battery voltage (VOL) display; Motor power and temperature (MOTOR) display; Brake display (); Turn on backlighting and lights (); Environment temperature ( or ) display; Data clearing; Fault code display; User parameter setting 24V, 36V, 48V supply voltage can automatic identification and be compatible Display ContentThe display content is shown as follow.-6-
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualButton DefinitionKT-LCD3 meter adopts the structural form with part design between the main partand operating buttons.There are three keys on the operating panel of button box, which are icons ofbutton (alt text UP),button (alt text SW) and(alt text DOWN).Button Box and Operating PanelNormal Operation On/OffHoldbutton (SW) long, the meter is powered on and into normal operation, andit provides the controller with power supply. Under normal operating status, holdbutton (SW) long, the meter is powered off, meanwhile to shutdown the power supply ofcontrollers. When the vehicle is stopped and without any button operation on themeter for five minutes, the meter will automatically shut down, and the power supplyof the electric vehicle will be powered off. In power off mode, the power consumption ofthe meter and controller is zero.-7-
ELECTRIC BICYCLE METER KT—LCD3 Product User Manual Display InterfaceDisplay 1The meter is startup to enter display 1.Display 1The followings are shown on display 1.Battery Capacity IndicatorSingle Trip Time (TM) DisplayPower Assist Ratio Gear (ASSIST)Real-time Trip Speed (Km/H)Single Trip Distance6Km/H Power Assist Function-8-
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualMotor Operation PowerEnvironment TemperatureBacklights and Headlights StatusBrake StatusCruise Function (CRUISE)Motor Running TemperatureDisplay 2In display 1, holdbutton (SW) shortly to enter display 2.Display 2The followings are shown on display 2:Total Trip Time (TTM)Total Trip Distance (ODO)-9-
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualSingle Average Speed (AVS)Motor Operating TemperatureIn the riding mode after 5 seconds, display 2 automatically returns to display 1. In display 1, the original motor power is replaced by motor running temperature as isshown in Figure.Display 3In display 2, holdbutton (SW) shortly to enter display 3.Display 3The followings are shown on display 3.Single Maximum Speed (MXS)Real-time Voltage (VOL)In the riding mode after 5 seconds, single maximum speed will automaticallyreturn to real-time trip speed (Km/H) as shown in the icon.- 10 -
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualIn display 3, holdbutton (SW) shortly again to enter display 1. In each display interface, if you holdbutton (SW) long, the meter will bepowered-off together with that of the controller. PAS Ratio (or Handlebar) Gear SwitchUnder normal operation, holdbutton (UP) orbutton (DOWN) toswitch the power assist ratio (or handlebar) gear (ASSIST), changing motor output power.Switching range is 1-5 gear (this can also be configured according to the customerrequirements), gear 1 is for the lowest power, and gear 5 is for the highest power.At every startup, the meter will automatically restore gear (this can also beconfigured as required by users) when it was at last shut down. When the powerassist ratio is gear 0 zero, there’s no power assist function. Power Assistant Push FunctionUsers can use 6Km/H power assist function when pushing vehicles. Holdbutton (DOWN), the meter assist function logo ( ) flashes, the vehicle drives at the speedof no more than 6Km/h. Releasebutton (DOWN), the assist function will be- 11 -
ELECTRIC BICYCLE METER KT—LCD3 Product User Manualrevoked. Cruise FunctionWhen C7 parameter setting is 1 (see C parameter setting), the meter turns on cruisefunction, holdbutton (DOWN) long to enter the cruise status when the vehiclespeed is more than 7 km/h, and the cruise function logo (CRUISE) lights. Brake or holdany button to revoke cruise function. Startup Backlights and HeadlightsHoldbutton (UP) long, the meter turns on the backlights as well as the vehicleheadlights (the Controller should have headlights driving and output functions), meterbacklighting and vehicle lights power logo (to turn off backlights and vehicle headlights.- 12 -) light, holdbutton (UP) long again
ELECTRIC BICYCLE METER KT—LCD3 Product User Manual Battery Capacity IndicatorThe meter can automatically identify 24V, 36V, 48V battery capacities when it issupporting use with the specified controller. When the battery capacity is over 70%, thefour power displays of the meter are lit, when the battery capacities drop, the four powerdisplays are off in order, when the power capacity is less than 15%, the four powerdisplays are totally turned off.When the controller is power off due to voltage shortage, the power display frameflashes, indicating the vehicle has been in voltage shortage and waiting for shutdowncurrently.Voltage shortage flashesBattery capacity indicator Motor Operating Power and TemperatureUnder the riding status of vehicle, the real time running and output power can beknown via the meter displays.- 13 -
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualMotor operating powerThe operating temperature of the motor shows there should be a temperaturesensor installed in the Inner motor to output the temperature for signal detectionsimultaneously.Motor operating temperatureWhen the motor operating temperature exceeds the warning value, temperaturedisplay flashes to alarm, meanwhile the motor controller will offer the appropriateprotection to motor. Environment TemperatureAfter startup, the environment temperature for using meter will be displayed inenvironment temperature display column.Environment temperature displayThe temperature display value may be in deviation shortly after boot-up, and thedisplay value will be gradually approaching the environment temperature within 10- 14 -
ELECTRIC BICYCLE METER KT—LCD3 Product User Manualminutes after boot-up. Single Data Clearing5 seconds after the meter is powered on, at display 1, hold both theand thebutton (UP)button (DOWN) simultaneously for about 2 seconds, the single trip time(TM) and single trip distance (DST) flicker, then holdbutton shortly (SW), therecord contents of both will be cleared.Single data clearing displayUnder the status of data flashing, if there were no operations on the data within 5seconds, the meter will automatically return to display1 after 5 seconds, and theoriginal record content will be saved. Automatically Prompt InterfaceError Code DisplayWhen the electronic control system of the electric vehicle fails, and the meter willautomatically display (flicker) fault code. You can’t exit the fault code display only thefault is removed.Error Code DisplayError Code & Definition Table- 15 -
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualError CodeDefinition01infoThrottle Abnormality03infoMotor Hall Signal Abnormality04infoTorque sensor Signal Abnormality05infoAxis speed sensor Abnormality(only applied to torque sensor )06infoMotor or controller has short circuit AbnormalityMotor operating temperature alarmUnder any interface, when the motor operating temperature exceeds the warning value,the motor operating temperature display flashes to alarm, meanwhile, the controller willoffer the appropriate protection to motor.User Setting ProjectKT-LCD3 meter user setting project General project setting P parameter setting C parameter settingGeneral Project Setting Maximum Trip SpeedUnder power off status, hold5 seconds after boot-up, holdbutton long (SW), the meter is turned on. Withinbutton (UP) andbutton (DOWN)simultaneously for about 2 seconds, the first is to enter the maximum riding speed settinginterface, then the speed display column flashes. Holdbutton shortly (UP) orbutton (DOWN) in order to set the maximum riding speed value. The default maximumriding speed value was 25Km/h. When the speed of the electric vehicle exceeds the setvalue, the motor will be stopped driving.- 16 -
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualSetting interface of maximum trip speedUnder the setting maximum riding speed interface, if there’s no button operationon the meter for more than 1 minute, and then the meter will automatically return todisplay 1, and the original set values will be saved.After finishing the maximum riding speed setting, holdbutton shortly (SW) tosave the current set values and enter into the next setting. Wheel DiameterAfter finishing the maximum riding speed setting, enter the wheel diameter settinginterface, and then the wheel diameter display column flashes. Holdbutton (UP) orbutton (DOWN) to choose the corresponding wheel diameter specification to aselected vehicle. The selection range of wheel diameter specifications are 13 species suchas 6,8,10,12,14,16,18,20,22,24,26,700 c and 28 inches.Setting Interface of Wheel DiameterUnder the wheel diameter setting interface, if there’s no button operation on themeter for more than 1 minute, and then the meter will automatically return to display1, and the original set values will be saved.After finishing the wheel diameter setting, holdcurrent set specification and enter into the next setting.- 17 -button (SW) shortly to save the
ELECTRIC BICYCLE METER KT—LCD3 Product User Manual Metric and Imperial UnitsAfter finishing the wheel diameter setting, enter into the metric/imperial units settinginterface, and then the speed and mileage unit flash. Holdbutton (UP) orbutton (DOWN) shortly to make sync selection of three metric/imperial units as speed,mileage, and the environment temperature.Setting Interface of Metric/Imperial UnitsDefinition Table of Metric/Imperial UnitsDisplayMetricImperialRiding speedKm/HMPHTotal ratureUnder the metric/imperial units setting interface, if there’s no button operationon the meter for more than 1 minute, and then the meter will automatically return todisplay 1, and the original set units will be saved.After finishing the metric/imperial units setting, holdbutton shortly (SW) tosave the current set values, and then speed and mileage units stop flashing. Holdbutton (SW) shortly again, and the meter will enter into the maximum riding speedinterface again, or holdbutton (SW) long for about 2 seconds to exit the generalproject setting environment and return to display 1. Exit General Project SettingAmong the three general project settings, after each setting is completed, if hold- 18 -
ELECTRIC BICYCLE METER KT—LCD3 Product User Manualbutton (SW) long for about 2 seconds, all can exit the setting environment and return todisplay 1, meanwhile, the current set parameters are saved.Under each setting interface, if there’s no button operation on the meter for more than1 minute, and then the meter will automatically return to display 1, and the original setparameters will be saved.P Parameter SettingAfter finishing metric/imperial unit settings, the speed and mileage units stop flashing.Within one minute after stopping flashing, holdbutton (UP) andbutton(DOWN) simultaneously for about 2 seconds to enter P parameter setting environment. P1 Motor Characteristic Parameter Setting ModeP1 is motor characteristic parameter setting mode. P1 motor gear reduction ratio number of rotor magnet pieces, just rounding if there’s any decimal.After entering P parameter setting environment, the first is to set P1parameter, P1parameter column flashes. P1 setting ranges between1-255, holdbutton (UP) orbutton (DOWN) shortly for selection.P1 parameter setting interfaceUnder P1 parameter setting interface, if there’s no button operation on themeter for more than 1 minute, and then the meter will automatically return to display1, and the original set parameter will be saved.After finishing P1 parameter setting, holdvalues and enter P2 parameter setting interface. P2 Wheel Speed Pulse Signal Setting Mode- 19 -button shortly to save the current set
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualEnter P2 parameter setting interface after P1 parameter setting is finished, and P2parameter column flashes.P2 parameter setting interfaceP2 is wheel speed pulse signal setting mode. If wheel generated 1 pulse signal by arevolution, P2 should be set as1. If wheel generated 6 pulse signals by a revolution, P2should be set as 6. If users didn’t configure the pulse signal system, and then P2 parametersetting can be 0. The setting range of P2 should be between 0-6, holdshortly orbutton (UP)button (DOWN) for selection.Under P2 parameter setting interface, if there’s no button operation on the meterfor more than 1 minute, and then the meter will automatically return to display 1,and the original set parameter will be saved.After finishing P2 parameter setting, holdbutton (SW) shortly to save thecurrent set values and enter P3 parameter setting interface.Please Note when P2 parameter is set to be 0, for the built-in clutch motor, there willbe the following defects, when the internal motor rotors stop or the internal rotor speed islower than the outer rotor speed, then the speed displayed on the meter is inaccurate! P3 Power Assist Control ModeEnter P3 parameter setting interface after P2 parameter setting is finished, and P3parameter column flashes.- 20 -
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualP3 parameter setting interfaceP3 is for power assist control mode, when P3 parameter setting is1, power assistcontrol mode is gear 5 of "imitation torque control" mode, when P3 parameter setting is0, power assist control mode is gear 5 of "speed control" mode. P3 parameter needs to bedetermined according to the distributed function of the controller, its setting range is 0 or 1,holdbutton (UP) shortly orbutton (DOWN) for selection. P3 parametersetting method is the same to that of P2. P4 Handlebar Startup ModeEnter P4 parameter setting interface after P3 parameter setting is finished, P4parameter column flashes.P4 parameter setting interfaceP4 is handlebar startup mode. When P4 setting is 1, indicating the handlebar is under"non-zero startup" mode, namely, the handlebar can be effective only after startup thefoot power assist. When P4 setting is 0, indicating the handlebar is under "zero startup"mode, the motor can be startup by the handlebar directly. P4 setting range is 0 or 1, holdbutton (UP) orbutton (DOWN) shortly for selection. P4 parameter settingmethod is the same to that of P2. P5 Power Monitoring Mode- 21 -
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualEnter P5 parameter setting interface after P4 parameter setting is finished, P5parameter column flashes.P5 parameter setting interfaceP5 is power monitoring mode, when P5 setting is 0, the power monitoring is the"real-time voltage" mode. Namely, it is the method to determine the battery capacitybased on real-time battery voltage. When P5 equals to a specified parameter, the powermonitoring is the "smart power" mode (this parameter is determined by the batterycharacteristics, ordinary 24V lithium is generally is 4-11, 36V lithium is between 5 15). P5setting ranges from 0-40, holdbutton (UP) orbutton (DOWN) shortly forselection. P 5 parameter setting method is the same to that of P2.After finishing P5 parameter setting, holdbutton (SW) shortly to save currentset the values, and then P5 parameter column stops flashing. Holdbutton (SW)shortly again, the meter re-enter P1 parameter setting interface. Or holdbutton (SW)long for about 2 seconds to exit P parameter setting environment and return to the display1. Exit P Parameter SettingAmong the five P parameter settings, when each parameter setting is completed, ifheldbutton (SW) long for about 2 seconds, all can exit the setting environment andreturn to display 1, meanwhile, the current set parameters would be saved.Under each parameter setting interface, if there’s no button operation on the meter formore than 1 minute, and then the meter will automatically return to display 1, and theoriginal set parameters will be saved.- 22 -
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualC Parameter SettingAfter finishing P5 parameter setting, P5 parameter column stops flashing. Within 1minute after stopping flashing, holdbutton (UP) andbutton (DOWN) forabout 2 seconds to enter C parameter setting environment. C1 Power Assist Sensor and Parameter Select ModeSet C1 parameter first after entering C parameter setting environment, C1 parametercolumn flashes.C1 parameter setting interfaceC1 is power assist sensor and parameter select mode. Its definition is shown infollowing table. C1 setting ranges between 0-7, holdbutton (UP) orbutton(DOWN) for selection.C1 parameter definition tableC1Quantum power assist sensors or similarC1Power assist sensors from othervalueproductsvaluemanufacturers005 magnet sensor05018magnet sensor060210 magnet sensor070312 magnet sensor04After finishing C1 parameter setting, holdbutton (SW) shortly to save thecurrent set values and enter C2 parameter setting interface. C2 Motor Phase Classification Coding Mode- 23 -
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualEnter C2 parameter setting interface after C1 parameter setting is finished, C2parameter column flashes.C2 parameter setting interfaceC2 is motor phase classification coding mode. It is served as identification parameterof different phases of the motor when using sine wave drive and the default value is 0.When C2 setting is 0, indicating that the used Quantum motor phase is an ordinary one.When the setting is a certain value, indicating a particular motor phase is used. C2 settingrange is 0-7, holdbutton (UP) orbutton (DOWN) for selection.After finishing C2 parameter setting, holdbutton (SW) shortly to save thecurrent set values and enter C3 parameter setting interface. C3 Power Assist Ratio Gear Initialization ModeEnter C3 parameter setting interface after C2 parameter setting is finished, C3parameter column flashes.C3 parameter setting interfaceC3 is initialization mode of power assist ratio gear. The setting range is 0-6 (gear),holdbutton (UP) orbutton (DOWN) for selection. When C3 setting is 0, themeter is switched on, and the power assist ratio is at gear 0. When the setting is 1, themeter is powered on and the power assist ratio is at gear 1, and so on.- 24 -
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualAfter finishing C3 parameter setting, holdbutton (SW) shortly to save thecurrent set values and enter C4 parameter setting interface. C4 Handlebar Function Setting ModeEnter C4 parameter setting interface after C3 parameter setting is finished, C4parameter column flashes.C4 parameter setting interfaceC4 is handlebar function setting mode. The setting range is 0-4, hold(UP) orbuttonbutton (DOWN) for selection.C4 parameter definition tableC4Handlebar startup mode P4 0Handlebar startup mode P4 1value0zero startup handlebarNon-zero startup handlebarBefore power assist, the handlebarZero startup, handlebar speed limit is1speed limit is 6Km/h, after power6Km/hassist, handlebar is full speed.Zero startup, handlebar speed limit isNon-zero startup, handlebar isspecifiedspecified speed limit.2Zero startup, handlebar speed limit is3specified. (Power assist ratio iseffective at gear 0)4After finishing C4 parameter setting, hold- 25 -button (SW) shortly to save the
ELECTRIC BICYCLE METER KT—LCD3 Product User Manualcurrent set values and enter C5 parameter setting interface. C5 Controller Maximum Current Adjustment ModeEnter C5 parameter setting interface after C4 parameter setting is finished, C5parameter column flashes.C5 parameter setting interfaceC5 is controller maximum operating current adjustment mode (tiny-adjustment oflimit current value). The default value is 10, setting range is 0-10, holdorbutton (UP)button (DOWN) shortly for selection.C5 parameter definition tableC5 valueMaximum current value(A)00Maximum current value-501Maximum current value-4.502Maximum current value-403Maximum current value-3.504Maximum current value-305Maximum current value-2.506Maximum current value-207Maximum current value-1.508Maximum current value-109Maximum current value-0.510Maximum current valueWhen C5 setting is 10, maximum current value is controller maximum operatingcurrent value (ie, limit current value); when setting is 9, maximum current value minus- 26 -
ELECTRIC BICYCLE METER KT—LCD3 Product User Manual0.5A, when setting is 8, maximum current value minus 1A and so on.After finishing C5 parameter setting, holdbutton (SW) shortly to save thecurrent set values and enter C6 parameter setting interface. C6 Backlight Brightness Adjustment ModeEnter C6 parameter setting interface after C5 parameter setting is finished, C6parameter column flashes.C6 parameter setting interfaceC6 is the meter backlight brightness adjustment mode. The default value is 3, andsetting range is 1-5, holdbutton (UP) orbutton (DOWN) shortly forselection.C6 parameter definition tableC6 valueBacklight estAfter finishing C6 parameter setting, holdbutton (SW) shortly to save thecurrent set values and enter C7 parameter setting interface. C7 Cruise Function Setting ModeEnter C7 parameter setting interface after C6 parameter setting is finished, C7parameter column flashes.- 27 -
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualC7 parameter setting interfaceC7 is cruise function setting mode. The setting range is 0 or 1, holdorbutton (UP)button (DOWN) shortly for selection.C7 parameter definition tableC7 valueCruise function0Off1OnAfter finishing C7 parameter setting, holdbutton (SW) shortly to save thecurrent set values and enter C8 parameter setting interface. C8 Motor Operating Temperature Display ModeEnter C8 parameter setting interface after C7 parameter setting is finished, C8parameter column flashes.C8 parameter setting interfaceC8 is motor operating temperature display mode. The setting range is 0 or 1, holdbutton (UP) orbutton (DOWN) shortly for selection.C8 parameter definition tableC8 valueMotor operating temperature- 28 -
ELECTRIC BICYCLE METER KT—LCD3 Product User Manual0Function off1Function onPlease Note The motor operating temperature display requires installing temperaturesensor in the motor, output temperature detection signal simultaneously.After finishing C8 parameter setting, holdbutton (SW) shortly to save thecurrent set values and enter C9 parameter setting interface. C9 Startup Password Setting ModeEnter C9 parameter setting interface after C8 parameter setting is finished, C9parameter column flashes.C9 parameter setting interfaceC9 is meter power-on password setting mode. The default value is 0, holdbutton (UP) orbutton (DOWN) shortly for selection.C9 parameter definition tableC9 valueStartup password setting0Function off1Function onWhen C9 setting is 1, holdbutton (SW) shortly, indicating that the passwordfunction is startup, and then enter the password settings interface, three password settingcolumns flash.- 29 -
ELECTRIC BICYCLE METER KT—LCD3 Product User ManualPassword Setting InterfaceThe password setting is done sequentially from
In the riding mode after 5 seconds, display 2 automatically returns to display 1. In display 1, the original motor power is replaced by motor running temperature as is shown in Figure. Display 3 ： In display 2, hold button (SW ) shortly to enter display 3. Display 3 The followings are shown on display 3.
Bicycle Program office, striped 28 miles of bicycle lanes, updated the City s Bicycle Master Plan, installed over 650 bicycle parking racks and 250 bicycle route signs, and i
3. Cycleway facility design 18 3.1 Bicycle path (one-way) 20 3.2 Bicycle path (two-way) 30 3.3 Quietway 40 3.4 Shared path 48 3.5 Shared zone 52 4. Public bicycle parking 56 4.1 Integrated bicycle parking 56 4.2 Types of public bicycle parking 56 4.3 Key locations for public bicycle
Landry's Bicycles Platinum 2008 Bicycle Shop 24Natick MA Michigan - Platinum Platinum MI Catalyst Partners Platinum 2013 Professional Services 8Grand Rapids MI Minnesota - Platinum Platinum MN Quality Bicycle Products Platinum 2008 Bicycle Industry 450Bloomington MN . Giant Bicycle Gold 2017 Bicycle Industry 55Newbury Park CA
accomplishes this through planning, engineering and implementing bicycle facilities, including bicycle parking, and educating the community and agencies about bicycle transportation. Livable Streets is responsible for reviewing and fulfilling short-term bicycle parking requests and coordinating and assessing bicycle parking with other City .
LCD and Bracket View Installed KT-LCD3 6 LCD and Bracket Side View LCD and Bracket Side View LCD and Bracket View Optional Encircled Rubber LCD Bracket Mounts Ø22.2 or Ø25.4 Optional Encircled Rubber LCD Bracket Mounts Ø22.2 or Ø25.4 Optional Encircled Rubber LCD Bracket Mounts Ø22.2 or Ø25.4
For Owners of EG Athens 350 Electric Bicycle Table of Contents Descriptions: Page Installation Instructions 2 How to install the bicycle out of the box 2 Operation Instructions 3 How to operate the Electric Bicycle 3 About the Brake Safety Feature on all our Electric Bikes 4 .
4w00-mm postage meter rentals meter for connect green 1000/2000 & sendpro p1000/2000 76.00 59.28 22% 4w00-mh postage meter rentals meter for connect green 3000 & sendpro p3000 100.00 78.00 22% 1r0t postage meter rentals 1r0t postage meter 137.00 106.86 22% 1h00-mh postage meter rentals meter for sendpro c400 385.00 300.00 22%
BOX , LTCT METER, HT METER, GRID METER, PRODIGY METER & ABT METER. The bidder must qualify the technical requirements as specified in clause 2.0 stated below.The sealed envelopes shall be duly superscribed as v RATE CONTRACT FOR SUPPLY OF 3 PHASE METER WITH BOX & WITHOUT BOX , LTCT
