Getting Started With Cisco Configuration Professional
Getting Started withCisco Configuration ProfessionalAmericas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 527-0883Text Part Number: OL-15990-08
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALLSTATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUTWARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THATSHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSEOR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s publicdomain version of the UNIX operating system. All rights reserved. Copyright 1981, Regents of the University of California.NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITHALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUTLIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OFDEALING, USAGE, OR TRADE PRACTICE.IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCOOR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found atwww.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnershiprelationship between Cisco and any other company. (1005R)Getting Started with Cisco Configuration ProfessionalAny Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command displayoutput, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers inillustrative content is unintentional and coincidental. 2011 Cisco Systems, Inc. All rights reserved.
C O N T E N T SPrefaceiiiAudiencePurposeiiiiiiRelated DocumentationiiiObtaining Documentation and Submitting a Service RequestCHAPTER1Introduction1-1Understanding Cisco Configuration ProfessionalInitial Setup 1-1Initial Setup for Deployed DevicesInitial Setup for Switches 1-4Install Cisco CPCHAPTER2Applications Menu Field ReferenceManage Community 2-4User Profile 2-4Options 2-5Templates 2-5Offline or Demo Mode 2-631-22-1Understanding the User InterfaceWindow Layout 2-1Menu Bar 2-2Toolbar 2-3Status Bar 2-4CHAPTER1-11-5User Interface FeaturesOnline Helpiv2-12-42-8Device Communities and Configuration BasicsBasic Workflow3-13-1Understanding Device Communities3-1Creating a Community and Adding DevicesManaging the Devices in a CommunityDiscovering Devices3-23-43-5Getting Started with Cisco Configuration ProfessionalOL-15990-081
ContentsDevice Community Reference 3-6Manage Community Dialog BoxCommunity View Page 3-8Configuration Basics3-63-10Supplementary Information 3-15Things to Know About Discovering Devices 3-16Cisco CP Configuration Requirements 3-16Wrong Secure Shell Version May Cause Discovery to Fail 3-17Understanding Discovery Failed Error Messages 3-18Cisco CP May Overwrite Existing Credentials 3-20Proxy Server Settings Might Cause Discovery to Fail 3-20Setting the Java Heap Size Value to -Xmx256m 3-20Collecting Cisco CP Technical Support Logs 3-21Using Cisco Configuration Professional to Run show tech-support 3-21INDEXGetting Started with Cisco Configuration Professional2OL-15990-08
PrefaceAudienceThis guide is for system administrators and network managers who want to use a graphical user interfaceto manage standalone network devices or groups of devices. The guide presents Cisco ConfigurationProfessional as a solution.PurposeThe purpose of this guide is to help users get started with Cisco Configuration Professional. It consistsof these chapters: Introduction—What Cisco Configuration Professional is and what it does. User Interface Features—Explains the user interface features. Device Communities and Configuration Basics—The procedures for creating communities andconfiguring devices.Related DocumentationTable 1 describes the related documentation available for Cisco Configuration Professional.Table 1Cisco Configuration Professional DocumentationDocument TitleAvailable FormatsReadme First forCisco Configuration ProfessionalThis document is available in the following locations:Cisco Configuration ProfessionalQuick Start Guide On Cisco.com. On the product CD-ROM in the Documentation folder.This guide is available in the following locations: On Cisco.com. On the product CD-ROM in the Documentation folder.Getting Started with Cisco Configuration ProfessionalOL-15990-08iii
PrefaceTable 1Cisco Configuration Professional Documentation (continued)Document TitleAvailable FormatsCisco Configuration ProfessionalGetting Started GuideThis guide is available in the following locations:Cisco Configuration ProfessionalUser GuideCisco Configuration ProfessionalExpress User Guide On Cisco.com. On the product CD-ROM in the Documentation folder. During the installation process, just before you have finishedinstalling the product, you are provided the option to read theGetting Started guide.This guide is available in the following locations: On Cisco.com. Accessible from Online help.This guide is available in the following locations: On Cisco. com. Accessible from Online help.Release Notes forCisco Configuration ProfessionalThis document is available in the following location:Release Notes forCisco Configuration ProfessionalExpressThis document is available in the following location: On Cisco.com.On Cisco.com.Obtaining Documentation and Submitting a Service RequestFor information on obtaining documentation, submitting a service request, and gathering additionalinformation, see the monthly What’s New in Cisco Product Documentation, which also lists all new andrevised Cisco technical documentation, w/whatsnew.htmlSubscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feedand set content to be delivered directly to your desktop using a reader application. The RSS feeds are a freeservice and Cisco currently supports RSS version 2.0.Getting Started with Cisco Configuration ProfessionalivOL-15990-08
CH A P T E R1IntroductionThis chapter introduces Cisco Configuration Professional (Cisco CP) and gives you the information thatyou need to start using it. This chapter contains the following sections: Understanding Cisco Configuration Professional Initial Setup Install Cisco CPUnderstanding Cisco Configuration ProfessionalCisco Configuration Professional (Cisco CP) is a GUI based device management tool for Cisco accessrouters. This tool simplifies routing, firewall, IPS, VPN, unified communications, WAN and LANconfiguration through GUI based easy-to-use wizards.Cisco CP is a valuable productivity enhancing tool for network administrators and channel partners fordeploying routers with increased confidence and ease. It offers a one-click router lockdown and aninnovative voice and security auditing capability to check and recommend changes to routerconfiguration. Cisco CP also monitors router status and troubleshoots WAN and VPN connectivityissues.Cisco CP is free and you can download prod release notes list.html.Cisco Configuration Professional Express (Cisco CP Express) is a light weight version of Cisco CP. Youcan use Cisco CP Express to configure basic security features on the router’s LAN and WAN interfaces.Cisco CP Express and a factory default configuration file are installed in Flash memory on routers thatare shipped with Cisco CP. You can connect a PC directly to the device, and then use Cisco CP Expressto configure LAN and WAN connections, a firewall, Network Address Translation, and make securitysettings before you place the device on the network in which it will operate. See the Initial Setup sectionto learn how to do this.Initial SetupDevices shipped with Cisco CP have a default configuration that allows you to connect a PC to anEthernet port on the device and start configuration immediately. This initial configuration isaccomplished using Cisco CP Express. You can use Cisco CP Express to give the device an IP addressGetting Started with Cisco Configuration ProfessionalOL-15990-081-1
Chapter 1IntroductionInitial Setupon the network in which it will operate, and the other basic configurations mentioned in the previoussection. After you have configured the device and connected it to the network, you will be able to useCisco CP to connect to the device over the network and make advanced configurations.If the device is not connected to the network yet and you want to use Cisco CP Express to give it an initialconfiguration, use the procedure in this section.NoteIf the device is already being used on your network, and you have installed Cisco CP on your PC, skipthis procedure and read Initial Setup for Deployed Devices.Step 1The device default configuration file configures an IP address for one Ethernet interface, and that mayconfigure the device as a DHCP server. Determine whether the device is configured as a DHCP server,and which Ethernet port to connect the PC to by referring to the following table.NoteIf the router model you want to configure does not appear in the following table, see the ReleaseNotes for Cisco Configuration Professional for updated information.Device ModelDHCP ServerConnect PC to the Applicable Ethernet PortCisco 815, Cisco 86x, Cisco 88x, Cisco180x, Cisco 1805, Cisco 1811, andCisco 1812YesACT Lnk, ETHERNET 10 BASE T, LAN,PWR Lnk, or SWITCHCisco 1841, Cisco 1861, Cisco 2801,Cisco 2811NoFast Ethernet 0/0Cisco 28xx, Cisco 38xxNoGigabit Ethernet 0/0Cisco 19xx, Cisco 29xx, Cisco 39xxNoGigabit Ethernet 0/0Step 2Connect the PC to the device appropriate port listed in the table.Step 3Configure the PC IP address by doing one of the following: If the device is configured as a DHCP server, ensure that the PC is configured to accept an IP addressfrom a DHCP server. If the device is not configured as a DHCP server, configure the static IP address 10.10.10.2 on thePC, and use the subnet mask 255.255.255.248.Step 4Open an Internet Explorer browser window, and enter the IP address 10.10.10.1 to connect to the deviceand start Cisco CP Express.Step 5Complete the Cisco CP Express wizard to configure the device.When you have completed initial setup and given the device an IP address on your LAN, you can useCisco CP to connect to the device and perform additional configuration.Getting Started with Cisco Configuration Professional1-2OL-15990-08
Chapter 1IntroductionInitial SetupInitial Setup for Deployed DevicesIf the device that you want to use Cisco CP to configure is already deployed, you should ensure that thedevice has a configuration that supports Cisco CP. The procedure in this section shows you how to addthe required configuration statements.NoteThe tasks that follow can also be accomplished using the Application Setup New Device option inCisco CP by connecting the PC to the console port of the device. See the topic Device Wizard in theCisco Configuration Professional User Guide 2.5 cts user guide list.html for more details.Step 1Log on to the router through an Ethernet port.Step 2When the router displays the user EXEC mode prompt, enter the enable command, and the enablepassword, if one is configured, as shown below:Router enablepassword passwordStep 3Enter config mode by entering the config terminal command, as shown in the following example.Router config terminalRouter(config)#Step 4Using the command syntax shown, create a user account with privilege level 15.Router(config)# username name privilege 15 secret 0 passwordStep 5If no router interface is configured with an IP address, configure one so that you can access the routerover the network. The following example shows the interface Fast Ethernet 0 configured.Router(config)# int FastEthernet0Router(config-if)# ip address 10.10.10.1 255.255.255.248Router(config-if)# no shutdownRouter(config-if)# exitIf you are going to connect the PC directly to the router, the PC must be on the same subnet as thisinterface.Step 6Configure the router as an http server for nonsecure communication, or as an https server for securecommunication.To configure the router as an http server, enter the ip http server command shown in the example:Router(config)# ip http serverTo configure the router as an https server, enter the ip http secure-server command shown in theexample:Router(config)# ip http secure-serverStep 7Configure the router for local authentication, by entering the ip http authentication local command, asshown in the example:Router(config)# ip http authentication localStep 8Configure the http timeout policy as shown in the example:Router(config)# ip http timeout-policy idle 60 life 86400 requests 10000Getting Started with Cisco Configuration ProfessionalOL-15990-081-3
Chapter 1IntroductionInitial SetupStep 9Configure the vty lines for privilege level 15. For nonsecure access, enter the transport input telnetcommand. For secure access, enter the transport input telnet ssh command. An example of thesecommands follows:Router(config)# (config)# ne)#Router(config-line)#Router(config-line)#vty 0 4privilege level 15login localtransport input telnettransport output telnettransport input telnet sshtransport output telnet sshexitvty 5 15privilege level 15login localtransport input telnettransport output telnettransport input telnet sshtransport output telnet sshendInitial Setup for SwitchesIf the device that you want to use Cisco CP to configure is already deployed, you should ensure that thedevice has a configuration that supports Cisco CP. The procedure in this section shows you how to addthe required configuration for the switch devices: CGS-2520-24TC and CGS-2520-16S-8PC.NoteThe tasks that follow can also be accomplished using the Application Setup New Device option inCisco CP by connecting the PC to the console port of the device. See the topic Device Wizard in theCisco Configuration Professional User Guide 2.5 cts user guide list.html for more details.Step 1Log on to the switch through the Console port or through an Ethernet port.Step 2When the switch displays the user EXEC mode prompt, enter the enable command, and the enablepassword, if one is configured, as shown below:Switch enablepassword passwordStep 3Enter config mode by entering the config terminal command, as shown in the following example.Switch config terminalSwitch(config)#Step 4Using the command syntax shown, create a user account with privilege level 15.Switch(config)# username name privilege 15 secret 0 passwordStep 5If IP Address is not configured, configure one so that you can access the switch over the network. Thefollowing example shows the IP Address configured on interface Vlan1.Switch(config)# interface Vlan1Switch(config-if)# ip address 10.10.10.1 255.255.255.248Switch(config-if)# no shutdownSwitch(config-if)# exitGetting Started with Cisco Configuration Professional1-4OL-15990-08
Chapter 1IntroductionInstall Cisco CPIf you are going to connect the PC directly to the switch, the PC must be on the same subnet as thisinterface.Step 6Configure the switch as an http server for nonsecure communication, or as an https server for securecommunication.To configure the switch as an http server, enter the ip http server command shown in the example:Switch(config)# ip http serverTo configure the switch as an https server, enter the ip http secure-server command shown in theexample:Switch(config)# ip http secure-serverStep 7Configure the switch for local authentication, by entering the ip http authentication local command, asshown in the example:Switch(config)# ip http authentication localStep 8Configure the http timeout policy as shown in the example:Switch(config)# ip http timeout-policy idle 60 life 86400 requests 10000Step 9Configure the vty lines for privilege level 15. For nonsecure access, enter the transport input telnetcommand. For secure access, enter the transport input telnet ssh command. An example of thesecommands follows:Switch(config)# (config)# ne)#Switch(config-line)#Switch(config-line)#vty 0 4privilege level 15login localtransport input telnettransport output telnettransport input telnet sshtransport output telnet sshexitvty 5 15privilege level 15login localtransport input telnettransport output telnettransport input telnet sshtransport output telnet sshendInstall Cisco CPInstall Cisco CP using the instructions in the Cisco Configuration Professional Quick Start Guide. Thisdocument is found on the Cisco CP CD. If you did not receive the CD, you can obtain this documentfrom the following link:http://www.cisco.com/en/US/docs/net mgmt/cisco configuration professional/guides/CiscoCPqsg.htmlAfter you have installed Cisco CP, you can create a community, and start configuring the devices in it.Getting Started with Cisco Configuration ProfessionalOL-15990-081-5
Chapter 1IntroductionInstall Cisco CPGetting Started with Cisco Configuration Professional1-6OL-15990-08
CH A P T E R2User Interface FeaturesThis chapter helps you understand the Cisco Configuration Professional (Cisco CP) user interface. Itcontains the following sections: Understanding the User Interface Online HelpUnderstanding the User InterfaceCisco CP eliminates the need for multiple device managers by providing a single tool to configure andmanage devices.The following sections describe the Cisco CP user interface: Window Layout Menu Bar Toolbar Status BarWindow LayoutThe user interface makes it easy to manage networking features. These are the main parts that define theuser interface: Menu Bar–The row of menus across the top of the window. It offers application services, a list ofopen windows, and online help. Toolbar–The row of icons directly below the menu bar. They represent the most often usedapplication services and most often configured networking features. Left Navigation Pane–The scalable panel on the left side of the content pane in which you select thefeatures to configure and monitor. Content Pane–The right side of the workspace, in which windows appear. You view reports here andenter information that configures networking features. Status Bar–The bar at the bottom of the window. Where Cisco CP displays the status of theapplication.Getting Started with Cisco Configuration ProfessionalOL-15990-082-1
Chapter 2User Interface FeaturesUnderstanding the User InterfaceMenu BarThe row of menus across the top of the window that offers application services:Table 2-1MenuMenu BarOptionsApplication Contains the following options:Help Manage Community—Allows you to create a new community or choose an existing community. SeeChapter 3, “Device Communities and Configuration Basics.” Create User Profile—Allows you to restrict users from using all of the features that are available in the leftnavigation pane. See User Profile, page 2-4. Import User Profile—Allows you to import a user profile. See User Profile, page 2-4. Options—Allows you to set user preferences such as log level, show community at startup, and show CLIpreview parameters. See Options, page 2-5. Template—Allows you to create, edit, or apply a template. See Templates, page 2-5. Work Offline—Allows you to work with Cisco Configuration Professional in offline mode. See Offline orDemo Mode, page 2-6. Exit—Exits the Cisco Configuration Professional application.Contains the following options: Help Contents—Displays the online help contents, which includes online help topics and links toscreencasts. Feedback—Displays a feedback form allowing you to provide feedback on Cisco ConfigurationProfessional. About—Displays information about Cisco Configuration Professional such as the version number andallows you to view the end-user licence agreement.Getting Started with Cisco Configuration Professional2-2OL-15990-08
Chapter 2User Interface FeaturesUnderstanding the User InterfaceToolbarCisco CP features are available from the toolbar at the top of the window. Table 2-2 describes these tools.Table 2-2Tool IconToolbarDescriptionHome button. Click this button to display the Community View page, which summarizesthe community information and allows you to add, edit, discover devices, and to view thediscovery and router status of each device.Configure button. Click this button to display the features that you can configure on achosen device. The features are displayed in the left navigation pane.NoteIf a feature (router, security, or voice) is not supported on a device, that feature isnot displayed in the left navigation pane.NoteIf the version of Cisco IOS that is installed on the device does not support aspecific feature, but an upgrade does support it, then that feature is disabled(grayed out) in the left navigation pane.Monitor button. Click this button to display the router and security features that you canmonitor for a chosen device. The features are displayed in the left navigation pane.NoteIf a feature (router or security) is not supported on a device, that feature is notdisplayed in the left navigation pane.NoteIf the version of Cisco IOS that is installed on the device does not support aspecific feature, but an upgrade does support it, then that feature is disabled(grayed out) in the left navigation pane.Manage Community icon. Click this icon to open the Manage Community dialog boxwhere you can add a new community or edit an existing community.Refresh icon. Click this button to: Rediscover the selected device in the Select Community Member drop-down menu.Rediscover and reload the current feature.NoteRefresh is not available for offline mode.NoteRefresh is available only after successful discovery of one or more devices.NoteClicking the Refresh button refreshes the device selected in the Select CommunityMember drop-down menu. Selecting a device in the Home Dashboard page andclicking Refresh does not refresh that device.Provide feedback to Cisco Systems icon. Click this icon to open the Cisco ConfigurationProfessional Feedback form, which you can use to send feedback about this product toCisco Systems.Help icon. Click this button to open the help page for the active window.Getting Started with Cisco Configuration ProfessionalOL-15990-082-3
Chapter 2User Interface FeaturesApplications Menu Field ReferenceStatus BarThe status bar displays Status information about Cisco CP and selected community members.When you are in the Home Dashboard Community View page, the padlock icon in thestatus bar displays the connection mode of the device that is selected in the Select CommunityMember drop-down list.NoteTable 2-3FeatureIconStatus BarFeatureNameDescriptionSecureConnectionThe locked padlock icon indicates that Cisco CP has a secure connectionwith the chosen community member.NonsecureConnectionThe unlocked padlock icon indicates that Cisco CP has a nonsecureconnection with the chosen community member.Applications Menu Field Reference Manage Community, page 2-4 User Profile, page 2-4 Options, page 2-5 Templates, page 2-5 Offline or Demo Mode, page 2-6Manage CommunitySee Chapter 3, “Device Communities and Configuration Basics.”User ProfileFor information about how to use Cisco Configuration Professional (Cisco CP) to create or import userprofiles, see the screencast at:http://www.cisco.com/en/US/docs/net mgmt/cisco configuration professional/scrcst/ccpsc.html.You must have internet access to view the screencast.Getting Started with Cisco Configuration Professional2-4OL-15990-08
Chapter 2User Interface FeaturesApplications Menu Field ReferenceOptionsUse the Options dialog box to set the user preferences such as log level, show community at startup, andshow CLI preview parameters at run time.How to Get to This Dialog BoxFrom the menu bar, choose Tools Options.Related Links Menu Bar, page 2-2Field ReferenceTable 2-4Options Dialog BoxElementDescriptionLog LevelChoose the log level that you want displayed in the log file from the drop-down list.Options are: Error—Choose the Error option to display only error messages in the log file. Thisoption is selected by default. Debug—Choose the Debug option to display error and debug messages in the log file.Use this option when you have experienced a problem with Cisco CP, and you want tosend the log files to Cisco TAC for assistance.After you choose the Debug option, recreate the problem that you want to log, and thenuse the Collect Data for TAC Support utility to send the log files to Cisco TAC. Forprocedure, see Collecting Cisco CP Technical Support Logs, page 3-21. After theproblem is fixed, we recommend that you change the log level back to Error.Show Community at Startupcheck boxBy default the Show Community at Startup check box is checked. When this check box ischecked, the Manage Community dialog box automatically displays when you startCisco CP. See Manage Community Dialog Box, page 3-6.Un-check the Show Community at Startup check box if you do not want Cisco CP todisplay the Manage Community dialog box on startup.Show CLI Previews check boxBy default the Show CLI Previews check box is checked. When this check box is checked,and you enter the parameters to configure a feature, the Deliver Configuration to Routerdialog box opens displaying the CLI commands to be delivered to the router.Un-check the Show CLI Previews check box if you do not want Cisco CP to display theCLI commands in the Deliver Configuration to Router dialog box before configuring afeature.TemplatesFor information about how to use Cisco Configuration Professional (Cisco CP) to configure Templates,see the screencast at:http://www.cisco.com/en/US/docs/net mgmt/cisco configuration professional/scrcst/ccpsc.html.You must have internet access to view the screencast.Getting Started with Cisco Configuration ProfessionalOL-15990-082-5
Chapter 2User Interface FeaturesApplications Menu Field ReferenceOffline or Demo ModeInformation about how to use Cisco Configuration Professional (Cisco CP) to configure the Offline orDemo mode feature, is provided in a screencast. Table 2-5 provides information about the dummydevices used in the screencast. It lists the hostnames, the corresponding hardware, and the mode used inthe screencast. See Table 2-5 and then view the screencast at:http://www.cisco.com/en/US/docs/net mgmt/cisco configuration professional/scrcst/ccpsc.htmlNoteTable 2-5You must have internet access to view the screencast.Dummy Device T1/E1Security-RoutingCISCO-2821-2WIC-2AM, WIC-2T, -2811-1WIC-1B-S/T, VWIC-2MFT-T1-DI, WIC-1ADSL, Security-RoutingAIM-IPS-K9CISCO-3845-1HWIC-AP-G-J, WIC-1SHDSL, WIC-1DSU-T1,NM-CIDS-K9, 4A/S, HWIC-4SHDSL, HWIC-1T,HWIC-1ADSLI, SCO-2811-2FXS-DID,T1-E1Gateway with SRSTCISCO-2821-3Default interfaces, no modulesGateway with SRSTCISCO-3845-2NME-CUE, FXS-DID, FXS, FXO, DID, T1-PRI,PVDM-32Cisco Unified Communications Manager ExpressCISCO-2821-1PVDM,VIC2-2FXS, NM-HDV2-1T1/E1Cisco Unified Communications Manager ExpressCISCO-2851-1VIC2-2BRI-NT/TEVoice GatewayCISCO-3825-12BRI,CUECisco Unified Communications Manager ExpressC1861-SRST-FK91861, 4FXS, 4FXO, 8xPOECisco Unified Communications Manager ExpressCISCO-SRST-888Default interfaces, no modulesGateway with SRSTCISCO-8918 FE switch ports, 1 FE layer 3, 1 GE layer 3, 1async, 1 wireless AP, 1 wireless-GESecurity-RoutingC1861-UC-2BRI-K9 1861, BRI, 4FXS, CUE, 8xPOECisco Unified Communications Manager ExpressCISCO-3945PVDM2-32, HWIC-AP-G-E, VIC2-2BRI-NT/TE, Cisco Unified Communications Manger ExpressNM-HDV2-1T1/E1CISCO-3925PVDM3-64, VIC2-4FXO, NM-HDV2-1T1/E1,PVDM2-48Cisco Unified Communications Manger ExpressCISCO-3845PVDM2-32, VIC2-2FXS, NM-CUE-ECCisco Unified Communications Manger ExpressCISCO-3825PVDM2-48, VWIC2-2MFT-, VIC2-4FXO,NM-16ESWGateway with Cisco Unified SRSTGetting Started with Cisco Configuration Professional2-6OL-15990-08
Chapter 2User Interface FeaturesApplications Menu Field ReferenceTable 2-5Dummy Device Information 64, VIC-4FXS/DID , HWIC-2FE,WIC-1AM-V2, NME-IPS-K9Cisco Unified Communications Manger ExpressCISCO-2921-1Default interfaceCisco Unified Communications Manger ExpressCISCO-2911/K9PVDM2-64, VIC2-4FXO, VIC3-4FXS/DIDCisco Unified Communications M
Getting Started Guide This guide is available in the following locations: † On Cisco.com. On the product CD-ROM in the Documentation† folder. During the installation process, just before you have finished † installing the product, you are provided the option to read the Getting Started guide. Cisco Configuration Professional User Guide
Apr 05, 2017 · Cisco 4G LTE and Cisco 4G LTE-Advanced Network Interface Module Installation Guide Table 1 Cisco 4G LTE NIM and Cisco 4G LTE-Advanced NIM SKUs Cisco 4G LTE NIM and Cisco 4G LTE-Advanced NIM SKUs Description Mode Operating Region Band NIM-4G-LTE-LA Cisco 4G LTE NIM module (LTE 2.5) for LATAM/APAC carriers. This SKU is File Size: 2MBPage Count: 18Explore furtherCisco 4G LTE Software Configuration Guide - GfK Etilizecontent.etilize.comSolved: 4G LTE Configuration - Cisco Communitycommunity.cisco.comCisco 4G LTE Software Configuration Guide - Ciscowww.cisco.comCisco 4G LTE-Advanced Configurationwww.cisco.com4G LTE Configuration - Cisco Communitycommunity.cisco.comRecommended to you b
Cisco ASA 5505 Cisco ASA 5505SP Cisco ASA 5510 Cisco ASA 5510SP Cisco ASA 5520 Cisco ASA 5520 VPN Cisco ASA 5540 Cisco ASA 5540 VPN Premium Cisco ASA 5540 VPN Cisco ASA 5550 Cisco ASA 5580-20 Cisco ASA 5580-40 Cisco ASA 5585-X Cisco ASA w/ AIP-SSM Cisco ASA w/ CSC-SSM Cisco C7600 Ser
Sep 11, 2017 · Note: Refer to the Getting Started with Cisco Commerce User Guide for detailed information on how to use common utilities for a record in Cisco Commerce. See Cisco Commerce Estimates and Configurations User Guide for more information.File Size: 664KBPage Count: 5Explore furtherSolved: Cisco Serial Number Lookups - Cisco Communitycommunity.cisco.comHow to view and/or update your CCO profilewww.cisco.comSolved: How do I associate a contract to my Cisco.com .community.cisco.comHow do I find my Cisco Contract Number? - Ciscowww.cisco.comPower calculator tool - Cisco Communitycommunity.cisco.comRecommended to you b
Cisco 3560 & 3750 NetFlow Configuration Guide Cisco Nexus 7000 NetFlow Configuration Cisco Nexus 1000v NetFlow Configuration Cisco ASR 9000 NetFlow Configuration Appendix. 8 Cisco NetFlow Configuration Cisco 3560X & 3750X NetFlow Configuration Your software release may not support all the features documented in this module.File Size: 2MB
Cisco 3560 & 3750 NetFlow Configuration Guide Cisco Nexus 7000 NetFlow Configuration Cisco Nexus 1000v NetFlow Configuration Cisco ASR 9000 NetFlow Configuration Appendix. 3 Cisco NetFlow Configuration Cisco IOS NetFlow Configuration Guide Netflow Configuration In configuration mode issue the following to enable NetFlow Export:
Supported Devices - Cisco SiSi NetFlow supported Cisco devices Cisco Catalyst 3560 Cisco 800 Cisco 7200 Cisco Catalyst 3750 Cisco 1800 Cisco 7600 Cisco Catalyst 4500 Cisco 1900 Cisco 12000 Cisco Catalyst 6500 Cisco 2800 Cisco ASR se
Cisco Nexus 1000V Cisco Nexus 1010 Cisco Nexus 4000 Cisco MDS 9100 Series Cisco Nexus 5000 Cisco Nexus 2000 Cisco Nexus 6000 Cisco MDS 9250i Multiservice Switch Cisco MDS 9700 Series Cisco Nexus 7000/7700 Cisco Nexus 3500 and 3000 CISCO NX-OS: From Hypervisor to Core CISCO DCNM: Single
Cisco Nexus 7706 Cisco ASR1001 . Cisco ISR 4431 Cisco Firepower 1010 Cisco Firepower 1140 Cisco Firepower 2110 Cisco Firepower 2130 Cisco FMC 1600 Cisco MDS 91485 Cisco Catalyst 3750X Cisco Catalyst 3850 Cisco Catalyst 4507 Cisco 5500 Wireless Controllers Cisco Aironet Access Points .
