2013 Fall Revision CycleFirst Draft ReportNFPA 69The First Draft Report Contains a compilation of the First Draft of the NFPAStandard, First Revisions, Public Input, Committee Input, Committee Statements,and Ballot Results and Statements. Where applicable, the First Draft Report alsocontains First Correlating Revisions, Correlating Notes, and Correlating Input. TheReport also contains a list of Technical Committee and Correlating CommitteeMembers.Public Comment Closing Date: November 16, 2012Important Notice - Pursuant to the NFPA Regulations Governing theDevelopment of NFPA Standards, Section 4.3.12, the following First Draft Reporthas been developed for public review.
Pursuant to the NFPA Regulations Governing the Development of NFPA Standards, Section 4.3.12, thefollowing First Draft Report has been developed for public review.Please note that the following First Draft Report represents an interim step in the implementation of thenew NFPA Standards Process and will ultimately be replaced by the NFPA Standards Development Sitewhich will provide a much more robust and interactive First Draft Report. This interim solution isprovided to ensure that reviewers of the First Draft Documents for the Fall 2013 revision cycle areprovided with a single report contacting all of the relevant materials addressed in the proposed FirstDraft NFPA Standard and to provide the required information to the user for their preparation forsubmission of Public Comments on the First Draft of the NFPA Standard.The First Draft Report is a consolidated report of the following individual items:1. First Draft – The First Draft of the NFPA Standard represents a “track changes” view of theproposed First Draft for public review. The First Draft contains all of the proposed changes tothe NFPA Standard by the Technical Committee2. First Revision Cross Reference – This document provides a cross reference between the FirstRevisions and the related Public Inputs as identified by the Technical Committee. This reportwill help a user to quickly identify what related Public Inputs should be review to get a completeunderstanding of the proposed changes by the Technical Committee.3. First Revision Report – This report contains of all of the First Revisions that have passedTechnical Committee letter ballot and which have been incorporated in to the First Draft. TheFirst Revisions have been organized in document order and are identified by the [FR #:FileMaker] number.4. Public Input Report – This report contains all of the submitted Public Input organized indocument order. Each Public Input contains the submitter information, recommendation, andthe Committee response to the Public Input.5. Ballot Results Report - This report contains the individual ballot results on each First Revisionand has been organized in First Revision order, by the [FR #: FileMaker] number. Additionally,where applicable the ballot results also contain any associated Ballot Statements by TechnicalCommittee Members.6. Additional Reports – Where applicable reports of Committee Input, Correlating First Revisions,and Correlating Notes have been included and organized in document order. Where thesereports are not included in the First Draft Report the document contained no Committee Input,Correlating First Revisions or Correlating Notes.If after your review of the First Draft and related First Draft Report you wish to submit Public Commentson the First Draft of the NFPA Standard please go to - www.nfpa.org/XXnext - (for example for NFPA 69– www.nfpa.org.69next) and click on the link to “Submit Public Comment Online” (Also, for furtherinstructions refer to Annex A in the back of the First Draft Report).Please note that the deadline for submitting Public Comments is November 16, 2012.
How to use this First Draft ReportThe First Draft Report is provided to the give the user a single document containing all of the relatedmaterials associated with the Technical Committee development of the First Draft of the NFPA Standard.The intent of the First Draft Report is to provide the public with a document that allows review andwhere applicable preparation of material for submission as Public Comments on the text of the FirstDraft.The user should initially review the First Draft of the NFPA Standard to determine if the proposedchanges (First Revisions) by the technical committee are acceptable. Where the user identifies areas ofthe document which require additional changes to address their concerns the user should then reviewthe related First Revisions, Public Inputs, and where applicable Committee Inputs, First CorrelatingRevisions or Correlating Notes to determine if their concerns have been addressed. These reports havebeen organized in document (section) order to allow the user to review all related material for a givensection of the NFPA standard. To assist in the user review a First Revision Cross Reference has beenprovided which details the Public Inputs that are directly related to a given First Revision.Additionally, where the user wishes to review all technical issues and concepts proposed through PublicInput, regardless of the incorporation into First Revisions, the user should review the Public InputReport, which is organized in document order to facilitate review.If during the review of the First Draft and First Draft Report material the user determines that additionalchanges need to be made to the First Draft of the NFPA Standard the user should then proceed to theNext Edition Tab of the appropriate Document Information Page to submit Public Comments on the FirstDraft. All submitted Public Comments will then be considered by the Technical Committee at theirComment Meeting.It is important to note that in accordance with the Regulations Governing the Development of NFPAStandards, Section 4.4.4, all Public Comments shall be limited to proposing revisions the First Draft ofthe NFPA Standard.If during the review of the First Draft Report or during the submission of Public Comments the user hasany questions please contact us at 617-984-7240 or via email at - standardsdev firstname.lastname@example.org.
Information on the NFPA Standards Development ProcessI. Applicable Regulations. The primary rules governing the processing of NFPA standards (codes, standards, recommendedpractices, and guides) are the NFPA Regulations Governing the Development of NFPA Standards (Regs). Other applicable rulesinclude NFPA Bylaws, NFPA Technical Meeting Convention Rules, NFPA Guide for the Conduct of Participants in the NFPAStandards Development Process, and the NFPA Regulations Governing Petitions to the Board of Directors from Decisions of theStandards Council. Most of these rules and regulations are contained in the NFPA Standards Directory. For copies of theDirectory, contact Codes and Standards Administration at NFPA Headquarters; all these documents are also available on theNFPA website at “www.nfpa.org.”The following is general information on the NFPA process. All participants, however, should refer to the actual rules andregulations for a full understanding of this process and for the criteria that govern participation.II. Technical Committee Report. The Technical Committee Report is defined as “the Report of the responsible Committee(s), inaccordance with the Regulations, in preparation of a new or revised NFPA Standard.” The Technical Committee Report is in twoparts and consists of the First Draft Report and the Second Draft Report. (See Regs at 1.4)III. Step 1: First Draft Report. The First Draft Report is defined as “Part one of the Technical Committee Report, whichdocuments the Input Stage.” The First Draft Report consists of the First Draft, Public Input, Committee Input, Committee andCorrelating Committee Statements, Correlating Input, Correlating Notes, and Ballot Statements. (See Regs at 184.108.40.206 andSection 4.3) Any objection to an action in the First Draft Report must be raised through the filing of an appropriate Comment forconsideration in the Second Draft Report or the objection will be considered resolved. [See Regs at 4.3.1(b)]IV. Step 2: Second Draft Report. The Second Draft Report is defined as “Part two of the Technical Committee Report, whichdocuments the Comment Stage." The Second Draft Report consists of the Second Draft, Public Comments with correspondingCommittee Actions and Committee Statements, Correlating Notes and their respective Committee Statements, CommitteeComments, Correlating Revisions, and Ballot Statements. (See Regs at Section 220.127.116.11 and 4.4) The First Draft Report and theSecond Draft Report together constitute the Technical Committee Report. Any outstanding objection following the Second DraftReport must be raised through an appropriate Amending Motion at the Association Technical Meeting or the objection will beconsidered resolved. [See Regs at 4.4.1(b)]V. Step 3a: Action at Association Technical Meeting. Following the publication of the Second Draft Report, there is a periodduring which those wishing to make proper Amending Motions on the Technical Committee Reports must signal their intentionby submitting a Notice of Intent to Make a Motion. (See Regs at 4.5.2) Standards that receive notice of proper AmendingMotions (Certified Amending Motions) will be presented for action at the annual June Association Technical Meeting. At themeeting, the NFPA membership can consider and act on these Certified Amending Motions as well as Follow-up AmendingMotions, that is, motions that become necessary as a result of a previous successful Amending Motion. (See 18.104.22.168 through22.214.171.124 and Table1, Columns 1-3 of Regs for a summary of the available Amending Motions and who may make them.) Anyoutstanding objection following action at an Association Technical Meeting (and any further Technical Committee considerationfollowing successful Amending Motions, see Regs at 126.96.36.199 through 188.8.131.52) must be raised through an appeal to the StandardsCouncil or it will be considered to be resolved.VI. Step 3b: Documents Forwarded Directly to the Council. Where no Notice of Intent to Make a Motion (NITMAM) isreceived and certified in accordance with the Technical Meeting Convention Rules, the standard is forwarded directly to theStandards Council for action on issuance. Objections are deemed to be resolved for these documents. (See Regs at 184.108.40.206)VII. Step 4a: Council Appeals. Anyone can appeal to the Standards Council concerning procedural or substantive mattersrelated to the development, content, or issuance of any document of the Association or on matters within the purview of theauthority of the Council, as established by the Bylaws and as determined by the Board of Directors. Such appeals must be inwritten form and filed with the Secretary of the Standards Council (See Regs at 1.6). Time constraints for filing an appeal mustbe in accordance with 1.6.2 of the Regs. Objections are deemed to be resolved if not pursued at this level.VIII. Step 4b: Document Issuance. The Standards Council is the issuer of all documents (see Article 8 of Bylaws). The Councilacts on the issuance of a document presented for action at an Association Technical Meeting within 75 days from the date of therecommendation from the Association Technical Meeting, unless this period is extended by the Council (See Regs at 4.7.2). Fordocuments forwarded directly to the Standards Council, the Council acts on the issuance of the document at its next scheduled
meeting, or at such other meeting as the Council may determine (See Regs at 220.127.116.11 and 4.7.4).IX. Petitions to the Board of Directors. The Standards Council has been delegated the responsibility for the administration ofthe codes and standards development process and the issuance of documents. However, where extraordinary circumstancesrequiring the intervention of the Board of Directors exist, the Board of Directors may take any action necessary to fulfill itsobligations to preserve the integrity of the codes and standards development process and to protect the interests of theAssociation. The rules for petitioning the Board of Directors can be found in the Regulations Governing Petitions to the Board ofDirectors from Decisions of the Standards Council and in 1.7 of the Regs.X. For More Information. The program for the Association Technical Meeting (as well as the NFPA website as informationbecomes available) should be consulted for the date on which each report scheduled for consideration at the meeting will bepresented. For copies of the First Draft Report and Second Draft Report as well as more information on NFPA rules and for upto-date information on schedules and deadlines for processing NFPA documents, check the NFPA website(www.nfpa.org/aboutthecodes) or contact NFPA Codes & Standards Administration at (617) 984-7246.
Report of the Committee onExplosion Protection Systems [EXL-AAA]Samuel A. Rodgers, ChairHoneywell, Inc., VA [U*]Luke S. Morrison, SecretaryProfessional Loss Control Inc., Canada [SE*]Michael Davies, PROTEGO, Germany [M*]Todd A. Dillon, XL Global Asset Protection Services, OH [I*]Alexi I. Dimopoulos, ExxonMobil Corporation, VA [U*]Rep. American Petroleum InstituteHenry L. Febo, Jr., FM Global, MA [I*]Robert J. Feldkamp, Nordson Corporation, OH [M*]Larry D. Floyd, BASF/Ciba Specialty Chemicals Corporation, AL [U*]Joseph P. Gillis, Westboro, MA [SE*]John E. Going, Fike Corporation, MO [M*]Stanley S. Grossel, Process Safety & Design Consultant, NJ [SE*]Dan A. Guaricci, ATEX Explosion Protection, L.P., FL [M*]Michael D. Hard, Hard Fire Suppression Systems, Inc., OH [IM*]Rep. Fire Suppression Systems AssociationDavid D. Herrmann, E. I. DuPont de Nemours & Company, DE [U*]Alfonso F. Ibarreta, Exponent, Inc., MA [SE*]David C. Kirby, Baker Engineering & Risk Consultants, Inc., WV [SE*]Steven A. McCoy, Corn Products/National Starch, IN [U*]Rep. NFPA Industrial Fire Protection SectionJames O. Paavola, DTE Energy/Detroit Edison Company, MI [U*]Stefan Penno, Rembe GmbH Safety & Control, Germany [M*]Mitchel L. Rooker, BS&B Safety Systems, LLC, OK [M*]Joseph A. Senecal, UTC/Kidde-Fenwal, Inc., MA [M*]Cleveland B. Skinker, Bechtel Power Corporation, MD [SE*]Bill Stevenson, CV Technology, Inc., FL [M*]David R. Stottmann, ST Storage, KS [M*]Stephen M. Stuart, Hylant Group, MI [I*]Erdem A. Ural, Loss Prevention Science & Technologies, Inc., MA [SE*]Robert G. Zalosh, Firexplo, MA [SE*]AlternatesGeof Brazier, BS&B Safety Systems, LLC, OK [M*](Alt. to Mitchel L. Rooker)Martin P. Clouthier, Professional Loss Control Inc., Canada [SE*](Alt. to Luke S. Morrison)Randal R. Davis, UTC/Kidde-Fenwal, Inc., MA [M*]NFPA 69/Front Matter/F2013/ROP/1
(Alt. to Joseph A. Senecal)Paul F. Hart, XL Global Asset Protection Services, IL [I*](Alt. to Todd A. Dillon)Kirk W. Humbrecht, Phoenix Fire Systems, Inc., IL [IM*](Alt. to Michael D. Hard)Eric R. Johnson, Savannah River Nuclear Solutions, LLC, SC [U*](Voting Alt. to Savannah River Nuclear Rep.)Edward L. Jones, Nordson Corporation, OH [M*](Alt. to Robert J. Feldkamp)Jason Krbec, CV Technology, Inc., FL [M*](Alt. to Bill Stevenson)John A. LeBlanc, FM Global, MA [I*](Alt. to Henry L. Febo, Jr.)Gerd Ph. Mayer, Rembe, Inc., NC [M(Alt. to Stefan Penno)Keith McGuire, CST Storage, KS [M*](Alt. to David R. Stottmann)Timothy J. Myers, Exponent, Inc., MA [SE*](Alt. to Alfonso F. Ibarreta)Thomas C. Scherpa, The DuPont Company, Inc., NH [U*](Alt. to David D. Herrmann)Jef Snoeys, Fike Corporation, Belgium [M*](Alt. to John E. Going)James Kelly Thomas, Baker Engineering & Risk Consultants, Inc., TX [SE*](Alt. to David C. Kirby)NonvotingFranz Alfert, Inburex Consulting, Germany [SE*]Laurence G. Britton, Process Safety Consultant, WV [SE*]Vladimir Molkov, University of Ulster, Northern Ireland, UK [SE*]Harry Verakis, US Department of Labor, WV [E*]Richard F. Schwab, Basking Ridge, NJ [SE*](Member Emeritus)Staff Liaison: Barry D. ChaseThis list represents the membership at the time the Committee was balloted on the text of this edition.Since that time, changes in the membership may have occurred.* A key to classifications is found in Annex A of this document.Committee Scope: This Committee shall have primary responsibility for documents on explosion protectionsystems for all types of equipment and for buildings, except pressure venting devices designed to protect againstoverpressure of vessels such as those containing flammable liquids, liquefied gases, and compressed gases underfire exposure conditions, as now covered in existing NFPA standards.NFPA 69/Front Matter/F2013/ROP/2
Copyright National Fire Protection Association 2013. All rights reserved. This copyis solely for your personal, noncommercial use in connection with participation in theNFPA Standards Development Process. Except for limited hard copies reasonablynecessary for such use, this copy may not be reproduced or redistributed. Foradditional copies of this and other downloadable reports related to the NFPAStandards Development Process visit www.nfpa.org.First Draft Report NFPA 69Standard on Explosion Prevention SystemsProposed 2014 EditionIMPORTANT NOTE: This NFPA document is made available for use subject to importantnotices and legal disclaimers. These notices and disclaimers appear in all publicationscontaining this document and may be found under the heading “Important Notices andDisclaimers Concerning NFPA Documents.” They can also be obtained on request from NFPAor viewed at www.nfpa.org/disclaimers.NOTICE: An asterisk (*) following the number or letter designating a paragraph indicates thatexplanatory material on the paragraph can be found in Annex A.Changes other than editorial are indicated by a vertical rule beside the paragraph, table, or figure inwhich the change occurred. These rules are included as an aid to the user in identifying changes fromthe previous edition. Where one or more complete paragraphs have been deleted, the deletion isindicated by a bullet ( ) between the paragraphs that remain.A reference in brackets [ ] following a section or paragraph indicates material that has been extractedfrom another NFPA document. As an aid to the user, the complete title and edition of the sourcedocuments for extracts in mandatory sections of the document are given in Chapter 2 and those forextracts in informational sections are given in Annex G. Editorial changes to extracted materialconsist of revising references to an appropriate division in this document or the inclusion of thedocument number with the division number when the reference is to the original document. Requestsfor interpretations or revisions of extracted text shall be sent to the technical committee responsiblefor the source document.Information on referenced publications can be found in Chapter 2 and Annex G.Chapter 1AdministrationFirst Revision No. 38:NFPA 69-2008[FR 39: FileMaker]1.1 Scope. Reserved. This standard applies to the design, installation, operation, maintenance, andtesting of systems for the prevention of explosions by means of the following methods:(a1) cControl of oxidant concentration;(b2) cControl of combustible concentration;(c3) pPredeflagration detection and control of ignition sources;(d4) eExplosion suppression;(e5) aActive isolation;(f6) pPassive isolation;(g7) dDeflagration pressure containment;1First Draft Report: Proposed 2014 Edition NFPA 69
(h8) pPassive explosion suppression.1.2 Purpose.1.2.1 This standard shall cover the minimum requirements for installing systems for the preventionof explosions in enclosures that contain flammable concentrations of flammable gases, vapors, mists,dusts, or hybrid mixtures.1.2.2 This standard shall provide basic information for design engineers, operating personnel, andauthorities having jurisdiction.First Revision No. 2:NFPA 69-2008[FR 2: FileMaker]1.2.3* To meet a minimum level of reliability, explosion prevention and control systems designed andinstalled provided in accordance with the requirements of this standard shall include, but not belimited to, the following:(1) Design system verification through testing(2) Third-party inspection and approval of protection systems equipment and methodologies by aninternationally recognized testing laboratory for the function intended, as where specified in Chapters7 through 14.(6) (3) Design documentation(5) (4) Commissioning tests System acceptance(3) (5) Management of change(4) (6) Regular testing and maintenance1.3 Application. This standard shall apply to methods for preventing and controlling explosions.First Revision No. 39:NFPA 69-2008[FR 40: FileMaker]1.3.1 1.3.1 When desired by the owner or operator, or required by the authority having jurisdiction, orwhen required by other standards, explosion prevention shall be achieved by one or more of thefollowing methods as required to mitigate the damage, prevent the transport of the an ignition source,and propagate prevent the deflagration:(1) Using the methods in Chapter 7 or 8 to control the environment within the protected enclosure,such that a deflagration cannot occur(2) Using the methods in Chapter 9, 11, or 12 to prevent the propagation of a deflagration toconnected vessels or to prevent the transport of an ignition source(3) Using the methods in Chapter 10, 13, or 14, or of in NFPA 68, Standard on Explosion Protectionby Deflagration Venting, to mitigate the effects of the deflagration, such that the protected enclosurewill not be uncontrollably breached18.104.22.168 It shall be permitted to use the methods in Chapters 4 and 5 in lieu of the methods inChapters 7 through 22.214.171.124.2 This standard shall apply to methods for predeflagration detection or control of an ignition.When desired by the owner or operator, or required by the authority having jurisdiction, or whenrequired by other standards, predeflagration detection or control of an ignition shall be achieved bymethods described in Chapter 126.96.36.199.2.1 These methods shall be permitted to be used independently to reduce the frequency ofdeflagrations.188.8.131.52.2 These methods shall be permitted to be used as an additional detector for a method ofChapter 10, 11, 12, or 184.108.40.206.2.3 These methods shall not interfere with the operation of the validated system.220.127.116.11.4 These methods shall not be permitted to be used as the sole detector for a method ofChapter 10, 11, 12, or 13.2First Draft Report: Proposed 2014 Edition NFPA 69
18.104.22.168* When another standard requires explosion prevention or control in accordance with NFPA 69for an enclosure and that enclosure is interconnected to other enclosures by a line containingcombustible dust, gas, mist, or hybrid mixtures that could transmit flame or pressure from the originalenclosure, explosion prevention or control shall be provided for interconnected enclosures by one ofthe following methods:(1) Deflagration isolation as discussed in Chapters 11 and 12(2) Explosion venting of the interconnected enclosures within the limitations specified in NFPA 68,Section 8.10(3) Containment as discussed in Chapter 13(4) Expanded metal mesh or polymer foam as discussed in Chapter 22.214.171.124 It shall be permitted to eliminate deflagration isolation protection for interconnectedenclosures based on a documented risk analysis acceptable to the authority having jurisdiction,unless isolation protection is specifically required for such enclosure by other standards.1.3.2 This standard shall not apply to the following conditions:(1) Devices or systems designed to protect against detonations(2)* (2)*Design, construction, and installation of deflagration vents(3) Protection against overpressure due to phenomena other than internal deflagrations(4) Chemical reactions other than combustion processes(5) Unconfined deflagrations, such as open-air or vapor cloud explosions(6) Rock dusting of coal mines, as covered by 30 CFR 75(7) General use of inert gas for fire extinguishment(8)* (8)*Preparation of tanks, piping, or other enclosures for hot work, such as cutting and welding(9) Ovens or furnaces handling flammable or combustible atmospheres, as covered by NFPA 86(10) Marine vapor control systems regulated by 33 CFR 154(11) Marine vessel tanks regulated by 46 CFR 30, 32, 35, and 391.4 Retroactivity. The provisions of this standard reflect a consensus of what is necessary toprovide an acceptable degree of protection from the hazards addressed in this standard at the timethe standard was issued.1.4.1 Unless otherwise specified, the provisions of this standard shall not apply to facilities,equipment, structures, or installations that existed or were approved for construction or installationprior to the effective date of the standard. Where specified, the provisions of this standard shall beretroactive.1.4.2 In those cases where the authority having jurisdiction determines that the existing situationpresents an unacceptable degree of risk, the authority having jurisdiction shall be permitted to applyretroactively any portions of this standard deemed appropriate.1.4.3 The retroactive requirements of this standard shall be permitted to be modified if theirapplication clearly would be impractical in the judgment of the authority having jurisdiction, and onlywhere it is clearly evident that a reasonable degree of safety is provided.1.5 Equivalency. Nothing in the standard is intended to prevent the use of systems, methods, ordevices of equivalent or superior quality, strength, fire resistance, effectiveness, durability, and safetyover those prescribed by this standard.1.5.1 Technical documentation shall be submitted to the authority having jurisdiction to demonstrateequivalency.1.5.2 The system, method, or device shall be approved for the intended purpose by the authorityhaving jurisdiction.Chapter 2 Referenced Publications2.1 General. The documents or portions thereof listed in this chapter are referenced within thisstandard and shall be considered part of the requirements of this document.3First Draft Report: Proposed 2014 Edition NFPA 69
2.2 NFPA Publications. National Fire Protection Association, 1 Batterymarch Park, Quincy, MA02169-7471.NFPA 61, Standard for the Prevention of Fires and Dust Explosions in Agricultural and FoodProcessing Facilities, 2008 edition.NFPA 68, Standard on Explosion Protection by Deflagration Venting, 2007 edition.NFPA 70, National Electrical Code , 2008 edition.NFPA 72 , National Fire Alarm Code , 2007 edition.NFPA 86, Standard for Ovens and Furnaces, 2007 edition.NFPA 271, Standard Method of Test for Heat and Visible Smoke Release Rates for Materials andProducts Using an Oxygen Consumption Calorimeter, 2004 edition.NFPA 326, Standard for the Safeguarding of Tanks and Containers for Entry, Cleaning, or Repair,2005 edition.NFPA 484, Standard for Combustible Metals, 2006 edition.NFPA 654, Standard for the Prevention of Fire and Dust Explosions from the Manufacturing,Processing, and Handling of Combustible Particulate Solids, 2006 edition.2.3 Other Publications.2.3.1 API Publications. American Petroleum Institute, 1220 L Street, NW, Washington, DC 200054070.API 510, Pressure Vessel Inspection Code: Maintenance Inspection, Rating, Repair, and Alteration,19126.96.36.199 ASME Publications. American Society of Mechanical Engineers, Three Park Avenue, NewYork, NY 10016-5990.ASME Boiler and Pressure Vessel Code, Section VIII, 2007.ASME B31.3, Process Piping, 2004.First Revision No. 8:NFPA 69-2008[FR 8: FileMaker]2.3.3 ASTM Publications. ASTM International, 100 Barr Harbor Drive, P.O. Box C700, WestConshohocken, PA 19428-2959.ASTM D 257, Standard Test Methods for DC Resistance or Conductance of Insulating Materials,2007 2005.ASTM D 3574, Standard Test Methods for Flexible Cellular Materials — Slab, Bonded and MoldedUrethane Foams, 2011 2003.ASTM E 2079, Standard Test Method for Limiting Oxygen (Oxidant) Concentration for Gases andVapors, 2007.2.3.4 CEN Publications. European Committee for Standardization, 36 rue de Stassart, B-1050Brussels, Belgium.EN 12874, Flame Arresters — Performance Requirements, Test Methods and Limits for Use, 2001.2.3.5 Military Specifications. Department of Defense Single Stock Point, Document Automationand Production Service, Building 4/D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.MIL-DTL-83054C, Baffle and Inerting Material, Aircraft Fuel Tank, 2003.MIL-PRF-87260A, Foam Material, Explosion Suppression, Inherently Electrically Conductive, forAircraft Fuel Tank and Dry Bay Areas, 19188.8.131.52 U.S. Government Publications. U.S. Government Printing Office, Washington, DC 20402.Title 29, Code of Federal Regulations, Part 1910.146, “Permit-Required Confined Spaces Standard.”Title 29, Code of Federal Regulations, Part 1910.147, “The Control of Hazardous Energy (LockOut/Tag-Out).”Title 30, Code of Federal Regulations, Part 75.Title 33, Code of Federal Regulations, Part 154, “Waterfront Facilities.”4First Draft Report: Proposed 2014 Edition NFPA 69
Title 46, Code of Federal Regulations, Part 30.Title 46, Code of Federal Regulations, Part 32, “Shipping.”Title 46, Code of Federal Regulations, Part 35.Title 46, Code of Federal Regulations, Part 39.Title 49, Code of Federal Regulations, Part 173.24, U.S. Department of Transportation, “GeneralRequirements for Packaging and Packages.”2.3.7 Other Publications.Bartknecht, W., Explosions: Course, Prevention, Protection, Springer-Verlag, Heidelberg, Germany,1989.Merriam-Webster’s Collegiate Dictionary, 11th edition, Merriam-Webster, Inc., Springfield, MA, 2003.2.4 References for Extracts in Mandatory Sections.NFPA 68, Standard on Explosion Protection by Deflagration Venting, 2007 edition.NFPA 72 , National Fire Alarm Code , 2007 edition.NFPA 302, Fire Protection Standard for Pleasure and Commercial Motor Craft, 2004 edition.NFPA 497, Recommended Practice for the Classification of Flammable Liquids, Gases, or Vaporsand of Hazardous (Classified) Locations for Electrical Installations in Chemical Process Areas, 2004edition.Chapter 3 Definitions3.1 General. The definitions contained in this chapter
Development of NFPA Standards, Section 4.3.12, the following First Draft Report has been developed for public review. . parts and consists of the First Draft Report and the Second Draft Report. (See Regs at 1.4) III. Step 1: First Draft Report. The First Draft Report is defined as "Part one of the Technical Committee Report, which
Prepared for District 5 Toastmasters By Mark Kramer, DTM Original Version July 2007 1st Revision June 2008 2nd Revision November 2008 3rd Revision June 2009 4th Revision May 2010 5th Revision May 2011 6th Revision May 2012 7th Revision May 2013 8th Revision May 2014 9th Revision Nov
NEW ORLEANS FACULTY HANDBOOK First Published, Fall 1956 Second Printing, Fall 1964 First Revision, Fall 1973 Second Revision, Fall 1981 Third Printing, Fall 1994 Third Revision, Fall 2001 Fourth Revision, Fall 2005 EFFECTIVE DATE: AUGUST 16, 1982
Triennial Cycle (Triennial Torah Cycle) / Septennial Cycle (Septennial Torah Cycle) Three and 1/2 year Lectionary Readings First Year of the Triennial Reading Cycle Tammuz
45678 CS-101 1 Fall 2009 F 54321 CS-101 1 Fall 2009 A-76543 CS-101 1 Fall 2009 A CS-347 1 Fall 2009 Taylor 3128 C 00128 CS-347 1 Fall 2009 A-12345 CS-347 1 Fall 2009 A 23856 CS-347 1 Fall 2009 A 54321 CS-347 1 Fall 2009 A 76543 CS-347 1 Fall 2009 A 10.7 Answer: a. Everytime a record is
100% duty cycle 300 A at 32 V, 60% duty cycle 200 A at 28 V, 100% duty cycle 250 A at 30 V, 60% duty cycle 500 A at 40 V, 100% duty cycle 600 A at 44 V, 60% duty cycle 400 A at 36 V, 100% duty cycle 500 A at 40 V, 60% duty cycle Welding Amperage Range 3–400 A 3–400 A 5–800 A 5–800 A Model
The Cycle subsystem drives processing of transactions through a Cycle Grid, which is comprised of a set of Cycle Agents. Each Cycle Agent is a separate JVM instance, which acts as a processing node in the Grid. A special application called a Cycle Client submits tasks to the Cycle Grid to direct what type of Cycle processing the group is to .
2.1 Life cycle techniques in life cycle sustainability assessment 5 2.2 (Environmental) life cycle assessment 6 2.3 Life cycle costing 14 2.4 Social life cycle assessment 22 3 Life Cycle Sustainability Assessment in Practice 34 3.1 Conducting a step-by-step life cycle sustainability assessment 34 3.2 Additional LCSA issues 41 4 A Way Forward 46
ENGLISH (MY PALS) I-SCIENCE Revision Revision Class Revision ART & CRAFT Class AKHLAQ FIQH Revision AQIDAH Class SEERAH Revision ARABIC EJAAN Revision COMPUTER Revision SHAPING MATHS FINAL SEMESTER EXAMINATION TIMETABLE 2014 - PRIMARY 1 IBN RUSYD JAWI Break Dhuha Iqra' & Hafazan Revisio