INSTALLATION MANUAL & CHECK OFF SHEET - Palfinger
INSTALLATION MANUAL& CHECK OFF SHEETMiniFix, 1100 lbs. CapacityMiniFix, 1320 lbs. Capacity06/16
MiniFix 1100/1320Installation ManualMiniFix 1100 / 1320 Installation ManualDocument Part Number: 90-0913-200ECN-M0792, Rev. 1.5, 06-16-16Copyright 2015 Palfinger Liftgates LLC.All rights reserved.Information in this document is subject to change without notice.Visit www.palfinger.com for up to date information and notifications.If you received this product with damaged or missing parts,contact Palfinger Liftgates at (888) 774-5844Parts Orderliftgateparts@palfinger.comTechnical R Liftgates, LLC.15939 Piuma Ave.Cerritos, CA 90703Tel: (888) 774-5844Fax: (562) 924-8318PALFINGER Liftgates, LLC.572 Whitehead Road.Trenton, NJ 08619Tel: (609) 587-4200Fax: (609) 587-4201Rev. 1.5-2-
MiniFix 1100/1320Installation ManualTable of Contents1Manual Updates v1.5 . 62Safety Information . 73Important Information . 83.1Recommended Tools for Installation . 104Dimension Sheet . 115General View of Liftgate . 126Mounting Notes: . 137Chassis and Body Preparation for Installation . 1387.1Checks Before Assembly . 137.2Preliminary work on the vehicle. 13Mount Plate and Liftgate Installation. 148.1Ford Transit Vehicle . 148.1.1Mounting Bracket Kit Overview - P/N: 65-0915-011. 148.1.2Chassis Preparation . 158.1.3Bracket Installation . 168.1.4Liftgate Installation . 178.2Mercedes Sprinter Vehicles . 188.3Mounting Bracket Kit – 118”/140” Wheelbase (Vehicle Models Prior to 2007)P/N; 65-0915-003. 188.48.3.1Chassis Preparation . 198.3.2Bracket Installation . 208.3.3Liftgate Installation . 21Mounting Bracket Kit – 158” Wheelbase (Vehicle Models Prior to 2007)P/N: 65-0915-004. 228.58.4.1Chassis Preparation . 228.4.2Bracket Installation . 238.4.3Liftgate Installation . 24Mounting Bracket Kit – 140” Wheelbase (Vehicle Models Prior to 2007)P/N: 65-0915-005. 258.68.5.1Chassis Preparation . 258.5.2Bracket Installation . 268.5.3Liftgate Installation . 27Mounting Bracket Kit – 158” Wheelbase (Vehicle Models Prior to 2007)P/N: 65-0915-006. 28Rev. 1.5-3-
MiniFix 1100/13208.7Installation Manual8.6.1Chassis Preparation . 288.6.2Bracket Installation . 298.6.3Liftgate Installation . 30Mounting Bracket Kit – 128” Wheelbase, 35” Overhang(Vehicle Models After 2007)P/N: 65-0915-007. 318.88.7.1Chassis Preparation . 318.7.2Bracket Installation . 328.7.3Liftgate Installation . 33Mounting Bracket Kit - 144”/170”/170” Ext. Wheelbase, 49”/64”/79” Overhang, Single/DualWheel (Vehicle Models After 2007) – P/N: 65-0915-008 . 348.98.8.1Chassis Preparation . 348.8.2Bracket Installation . 358.8.3Liftgate Installation . 36Mounting Bracket Kit – 144”/170” Wheelbase, 49”/79” Overhang, Dual Wheel (VehicleModels After 2007) – P/N: 65-0915-009 . 378.108.9.1Chassis Preparation . 378.9.2Bracket Installation . 388.9.3Liftgate Installation . 39Mounting Bracket Kit – 170” Wheelbase, Dual Wheel; 64” Overhang (Vehicle Models After2007) – P/N: 65-0915-010. 408.118.12Rev. 1.58.10.1Chassis Preparation . 408.10.2Bracket Installation . 418.10.3Liftgate Installation . 42Nissan NV Vehicles . 438.11.1Mounting Bracket Kit – Wheelbase 146“ – P/N: 65-0915-014 . 438.11.2Chassis Preparation . 438.11.3Bracket Installation . 448.11.4Liftgate Installation . 45Dodge Promaster Vehicles . 468.12.1Exhaust Modification Kit – 159“ Wheelbase P/N: 60-0914-000 . 468.12.2Exhaust Modification . 478.12.3Exhaust Modification Kit – 136“ Wheelbase - P/N: 60-0916-000. 518.12.4Exhaust Modification . 518.12.5Mounting Kits Overview . 548.12.6Bracket Installation . 55-4-
MiniFix 1100/13208.12.79Installation ManualLiftgate Installation . 59Electrical Installation . 609.1Battery Wiring Diagram . 619.2Wire Crimping . 629.3Circuit Breaker Installation . 639.4Cab On/Off Switch Installation . 649.4.1Operating Push Button Installation . 659.52-Button Hand Held Remote Control Installation . 689.6D-Bumper Installation . 709.7Platform Installation . 719.8Flip Ramp Installation . 769.9Setting of B-13 Sensor . 789.10Setting of B-16 Sensor . 799.11License Plate Light. 809.12Foot Control Installation (Optional) . 819.13Warning Lights Installation (Optional). 839.14Lubrication . 8610Hydraulic Schematic . 8711Electrical Schematic . 8812Decal Placement and Inspection . 9013Final Inspection Check List . 92Company Information:Company Name:Advisor Name:Trailer Year Make & Model:Liftgate Information:Liftgate Serial Number:Liftgate Model Number:Date of Purchase:Date of Installation:Rev. 1.5-5-
MiniFix 1100/13201Installation ManualManual Updates v1.5 Added exhaust modification kit for Promaster 136” wheelbase vehicles, Section 8.12.3.Rev. 1.5-6-
MiniFix 1100/13202Installation ManualSafety InformationThis manual follows the Guidelines set forth in “ANSI Z535.4-2007” for alerting you to possible hazards andtheir potential severity.! DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or seriousinjury.! WARNING indicates potentially hazardous situation which, if not avoided, could result in death or seriousinjury.! CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor ormoderate injury.CAUTION without the safety alert symbol is used to address practices not related to personal injury.(In this manual it is used to alert the user to potentially hazardous situation which, if not avoided, may resultin property damage.)NOTICE without the safety alert symbol is used to address practices not related to personal injury. (In thismanual it is to alert you to special instructions, steps, or procedures.) Always be aware of your surroundings. Wear eye protection at all times during installation. Ear protection and gloves should be used when necessary.Rev. 1.5-7-
MiniFix 1100/13203Installation ManualImportant InformationBefore Getting Started“READ FIRST”The MiniFix liftgate is a heavy duty industrial hydraulic lifting device. Performance and reliability areclosely related to proper installation, battery cable connections, and grounding. All groundingsurfaces MUST be cleaned, prepped, and sealed per this manual. “Cut to size” cables MUST beproperly crimped and sealed as factory supplied. All connections MUST be dressed with dielectricgrease or equivalent sealer.1. Read Manual completely before beginning any work.2. For Sprinter Series MY2007 and newer models Mercedes-Benz requires auxiliary battery kits.3. Refer to your truck manufacturer’s instructions before adding any auxiliary equipment.4. Pay Special attention to items marked with this symbol:5. All welding should be performed by qualified personnel per AWS standards.6. Always Ground closest to your welding point to prevent arcing through moving parts.7. Contact PALFINGER Liftgates. for Special Installations not covered in this Installation Manual.8. Do not paint cylinder shafts or nylon rollers (Use non-chlorinated brake cleaner to remove over spray)9. Verify that pin lock bolts are tight.10. Grease all pivot points.11. Verify that ALL decals are placed properly (Contact PALFINGER Liftgates to replace any missingdecals).Final Check-Off-Sheet at rear of this manual MUST be filled out and kept in your records for12.future reference.13. Refer to owner’s manual for troubleshooting & repairs.14. Mercedes allows the following lifting capacities for SPRINTER models at 24” center point of load.1) 1100 lbs. for SPRINTER Cargo Van Setup2) 1320 lbs. for SPRINTER Chassis Cab SetupRev. 1.5-8-
MiniFix 1100/1320Installation ManualImproper operation of this liftgate may result in severe personal injury or death. DO NOT operateunless you have been properly instructed, have read and are familiar with the procedures in thismanual. This manual has been designed to illustrate the steps needed for the basic installation ofthe MiniFix liftgate. It also provides safety information and simple preventive maintenance tips.This manual is not intended for use as a repair or troubleshooting guide. Repairs should beperformed by a Palfinger Liftgates Authorized Service Center.This Manual has been designed for use in conjunction with the MiniFix series liftgate only which isdesigned for different capacities and features.1) Refer to the serial number tag on the liftgate liftarm (Driver side).Name Plate2) Ask your employer or lessor;3) Call your Palfinger Liftgates Authorized Service Center for assistance.4) Call Palfinger Liftgates for assistance in the USA at 888-774-5844. You can also contact PalfingerLiftgates by fax (562) 924-8318 or on the internet at www.palfinger.com For technical support, contactPalfinger Liftgates or an authorized Palfinger service center. www.palfinger.comRev. 1.5-9-
MiniFix 1100/1320Installation ManualSpecial Notes on installs of the MiniFix liftgate on Dodge Promaster Vans:1. Liftgate will be mounted in the same location as spare tire. Space inside van will be requiredfor spare tire.2. Vehicles exhaust system will require modification.Special Notes on installs of the MiniFix liftgate on Ford Transit Vans:1. Liftgate will be mounted in the same location as spare tire. Space inside van will be requiredfor spare tire.2. Sensors on bumpers, rear camera (if applicable) will need relocation.3. Overhangs beyond 49” will require modifications to the vehicles springs due to softsuspension.Special Notes on installs of the MiniFix liftgate on Mercedes Sprinter Vans:1. LIftgate will be mounted in the same location as spare tire. Space inside van will be requiredfor spare tire.2. Sensor Bumpers will not work once bumper is removed.3. Step bumpers will need to be replaced with flat bumper.4. Must have auxiliary battery.3.1Recommended Tools for InstallationMetric Wrench SetBasic ScrewdriversPliersWire Crimp PliersDigital MultimeterSnap Ring PliersHammerMetric Allen Set½” Impact & SocketsSm. Metric Socket SetAssorted Drill BitsFloor Jack or Equiv.Sm. To Med. Bottle JackForklift or O/H CraneHand Held GrinderPaint GunPry Bar3/8 DrillGrease GunHeat Gun or Equiv.Min. 250 Amp WelderCutting Torch or Equiv.Measuring TapeSpecial tools required: 7/8” hole saw for installation of switches.Rev. 1.5- 10 -
MiniFix 1100/13204Installation ManualDimension Sheet[Type text]Minifix Chassis Dimension SheetContact InformationNotes:Quote#/SO#:Company:Phone: ( ) -Fax: ( ) -Email: @Vehicle **NissanOther: Vehicle r: Rear WheelSingle Rear Wheel (SRW)Dual Rear Wheel (DRW)DimensionsA Wheelbase: Center of front axle to center of rear axle . .B Overhang: Center of rear axle to end of rear bumper 35”A49”64”79”80”Other:B*Special Notes on installs of the Minifix liftgate for Dodge Promaster:1.2.Liftgate will be mounted in the same location as spare tire. Space inside van will be required for spare tire.Vehicles exhaust system will require modification.**Special Notes on installs of the Minifix liftgate for Ford Transit Vans:1.2.3.Liftgate will be mounted in the same location as spare tire. Space inside van will be required for spare tire.Sensors on bumpers, rear camera (if applicable) will need relocation.Overhangs beyond 49” will require modifications to the vehicles spring due to soft suspension.***Special Notes on installs of the Minifix liftgate for Mercedes Sprinter Vans:1.2.3.4.Rev. 1.5Liftgate will be mounted in the same location as spare tire. Space inside van will be required for spare tire.Sensor Bumpers will not work once bumper is removed.Step bumpers will need to be replaced with flat bumper.Must have auxiliary battery.- 11 -
MiniFix 1100/13205Installation ManualGeneral View of LiftgatePower Pack(Pump and MotorEnclosure)LiftarmParallelArmTilt Cylinder(Under Platform)PlatformMountTubeLiftCylinderFoot Control(Optional)CartStopsWarning Lights(Optional)Pump & MotorOilResevoirControlBoardRev. 1.5Pump and MotorEnclosure- 12 -
MiniFix 1100/13206Installation ManualMounting Notes:1. Read and clearly understand this manual BEFORE beginning ANY workImportantMin bed height: 18” with Van maximum loadedMax bed height: 31” with Van unloadedMinimum bed height dimensions are ALWAYS MAXIMUM LOADED VehicleCall tech support before starting the installation if you have any questions or concerns on mountingdimensions Toll free: 888-774-5844 - technical support7Chassis and Body Preparation for Installation7.1Checks Before Assembly 1. Does the liftgate match your order?2. Do you have the correct mount plates for your particular chassis?- Each Vehicle model requires its own specific mount plates.3. Are the assembly instructions for the Palfinger Liftgates MiniFix included?4. Does the operating voltage of the Palfinger Liftgates MiniFix match the vehicle voltage?5. Is a flip ramp included?6. Observe the chassis guidelines of the vehicle manufacturer for accessory equipment.7. Check size of battery for adequate capacity.8. Is there a compartment under passenger seat designed for an auxiliary battery?7.2Preliminary work on the vehicleFollow vehicles documenation for the removal of the1. Remove any spare wheels and their mounts from the vehicle rear underside.2. Remove any trailer and towing hitches as well as steps attached to the rear of the vehicle.3. Replace special step bumpers fitted with standard bumpers.4. Remove the licence plate on the rear doors and re-attach it in a visible position after assembly of thePalfinger Liftgates MiniFix (observe local and federal regulations).Rev. 1.5- 13 -
MiniFix 1100/13208Installation ManualMount Plate and Liftgate InstallationIMPORTANT:To install the liftgate it is very important to have the correct vehicle mount plates for the vehicle.8.1Ford Transit VehicleSpecial Notes on installs of the MiniFix liftgate on Ford Transit Vans:1. Liftgate will be mounted in the same location as spare tire. Space inside van will be requiredfor spare tire.2. Sensors on bumpers, rear camera (if applicable) will need relocation.3. Overhangs beyond 49” will require modifications to the vehicles springs due to softsuspension.8.1.1Mounting Bracket Kit Overview - P/N: 65-0915-011Driver SideMountingBracketCurb SideMountingBracketM12x1.75x100 mm Bolt8XRev. 1.5M12x1.75x35 mm Bolt4XM13 Washer28XM12x1.75 Nut8XM12 Spacer8X- 14 -
MiniFix 1100/13208.1.2Installation ManualChassis PreparationFor all vehicle modification, reference the manufacturer’s manual.1. Remove the hitch, if applicable.2. Remove the four (two per side) preinstalled M12 bolts located on the chassis. Do no discard thehardware; it will be used to complete the installation.3. Drill two M12 holes on the chassis as shown. Use the mounting bracket as a template to mark thedrill locations.DrillChassisRearBumperM12 PreinstalledBoltsRear TireDriver SideUnder Vehicle ViewDriver SideRev. 1.5- 15 -
MiniFix 1100/13208.1.3Installation ManualBracket Installation1. Use the M12 hardware to mount the bracket to the vehicles chassis. Reuse the M12 bolts that wereoriginally attached to the chassis. Follow the installation orientation of the hardware as shown below.Repeat the mounting process for the curb side bracket.ChassisRearBumperUnder Vehicle ViewDriver SideRear TireDriver SideChassis4xM12 Nylock Nut4x SpacerMounting BracketDriver Side4xM13 Washer4xM13 Washer2xM13 Washer4xM12x100 mm Bolt2xM12 Bolt(Existing)2xM12x35mm BoltTorque SpecificationsM12 –59 ft./lbs. (80 Nm)Rev. 1.5- 16 -
MiniFix 1100/13208.1.4Installation ManualLiftgate Installation1. Secure the MiniFix Mount Tube to the mounting brackets by bolting the sides of the mount tube tothe side of the brackets with the six (3 each side) M14 hardware provided with the liftgate.MinifixMount TubeM14NutM14BoltM14NutM14BoltTorque SpecificationsM14 – 140 ft./lbs. (190 Nm)Rev. 1.5- 17 -
MiniFix 1100/13208.2Installation ManualMercedes Sprinter VehiclesSpecial Notes on installs of the MiniFix liftgate on Mercedes Sprinter Vans:1. Liftgate will be mounted in the same location as spare tire. Space inside van will be requiredfor spare tire.2. Sensor Bumpers will not work once bumper is removed.3. Step bumpers will need to be replaced with flat bumper.4. Must have auxiliary battery.8.3Mounting Bracket Kit – 118”/140” Wheelbase (Vehicle Models Prior to 2007)P/N; 65-0915-003M12x1.75x100 mm Bolt12XRev. 1.5M13 Washer24XM12x1.75 Nut12XSpacer4X- 18 -
MiniFix 1100/13208.3.1Installation ManualChassis PreparationAttention: For precise drilling, use the mount plate bracket as a template to mark drilling locations.Driver side chassis frame shown below, repeat procedure on curb side.2x ø20mmOutsideWallChassis FramesBefore DrillingDrill2x ø12mmInsideWallChassis FramesAfter DrillingChassis Frame(Driver Side)260mm90mm70mmFront ofVehicleRear ofVehicleDrill2x ø12mm(Inside Wall)45mmDrill2x ø20mm(Outside Wall)Chassis Frame; Drill DimensionsSide ViewRev. 1.5- 19 -
MiniFix 1100/13208.3.2Installation ManualBracket Installation*SpacersM12Nylock NutM13WasherChassis Frame(Driver Side)Mounting Bracket(Driver Side)M12x100mm*SpacersM12x100MMBolt*NOTE: Spacers must be trimmedto the width of chassis frame.ChassisFrameWidth ofChassisFrameMountingBracketTorque SpecificationsM12 – 55 ft./lbs. (75 Nm)Rev. 1.5- 20 -
MiniFix 1100/13208.3.3Installation ManualLiftgate InstallationDue to the limited space available under the vehicle, the hydraulic power pack must be relocatedfrom the front of the mount tube to the rear for the 118” wheelbase.1. Secure the MiniFix Mount Tube to the mounting brackets by bolting the sides of the mount tube tothe side of the brackets with the six (3 each side) M14 hardware provided with the liftgate.M14NutM14BoltM14NutM14BoltTorque SpecificationsM14 – 129 ft./lbs. (175 Nm)Rev. 1.5- 21 -
MiniFix 1100/13208.4Installation ManualMounting Bracket Kit – 158” Wheelbase (Vehicle Models Prior to 2007)P/N: 65-0915-004M12x1.75x100 mm Bolt12XM13 Washer24X8.4.1M12x1.75 Nut12XSpacer4XChassis PreparationAttention: For precise drilling, use the mount plate bracket as a template to mark drilling locations.Driver side chassis frame shown below, repeat procedure on curb side.2x ø20mmOutsideWallChassis FramesBefore DrillingDrill2x ø12mmInsideWallChassis Frame(Driver Side)Chassis FramesAfter Drilling489mm70mm70mmFront ofVehicleRear ofVehicle56mmDrill2x ø12mm(Inside Wall)Drill2x ø20mm(Outside Wall)Chassis Frame; Drill DimensionsSide ViewRev. 1.5- 22 -
MiniFix 1100/13208.4.2Installation ManualBracket Installation*SpacersM12Nylock NutM13WasherChassis Frame(Driver Side)Mounting Bracket(Driver Side)M12x100mm*SpacersM12x100MMBolt*NOTE: Spacers must be trimmedto the width of chassis frame.ChassisFrameMountingBracketWidth ofChassisFrameTorque SpecificationsM12 – 55 ft./lbs. (75 Nm)Rev. 1.5- 23 -
MiniFix 1100/13208.4.3Installation ManualLiftgate Installation1. Secure the MiniFix Mount Tube to the mounting brackets by bolting the sides of the mount tube tothe side of the brackets with the six (3 each side) M14 hardware provided with the liftgate.M14NutM14BoltM14NutM14BoltTorque SpecificationsM14 – 129 ft./lbs. (175 Nm)Rev. 1.5- 24 -
MiniFix 1100/13208.5Installation ManualMounting Bracket Kit – 140” Wheelbase (Vehicle Models Prior to 2007)P/N: 65-0915-005Mounting Brackets2XM12x1.75x100 mm Bolt12XM12x1.75 Nut12XM13 Washer24X8.5.1Spacer4XChassis PreparationAttention: For precise drilling, use the mount plate bracket as a template to mark drilling locations.Driver side chassis frame shown below, repeat procedure on curb side.2x ø20mmOutsideWallChassis FramesBefore DrillingDrill2x ø12mmInsideWallChassis FramesAfter DrillingChassis Frame(Driver Side)560mm80mm70mmFront ofVehicleRear ofVehicle56mmDrill2x ø12mm(Inside Wall)Drill2x ø20mm(Outside Wall)Chassis Frame; Drill DimensionsSide ViewRev. 1.5- 25 -
MiniFix 1100/13208.5.2Installation ManualBracket Installation*SpacersM12NylockNutM13WasherChassis Frame(Driver Side)Mounting Bracket(Driver Side)M12x100MMBolt*Spacers*NOTE: Spacers must be trimmedto the width of chassis h ofChassisFrameTorque SpecificationsM12 – 55 ft./lbs. (75 Nm)Rev. 1.5- 26 -
MiniFix 1100/13208.5.3Installation ManualLiftgate Installation1. Secure the MiniFix Mount Tube to the mounting brackets by bolting the sides of the mount tube tothe side of the brackets with the six (3 each side) M14 hardware provided with the liftgate.M14NutM14BoltM14NutM14BoltTorque SpecificationsM14 – 129 ft./lbs. (175 Nm)Rev. 1.5- 27 -
MiniFix 1100/13208.6Installation ManualMounting Bracket Kit – 158” Wheelbase (Vehicle Models Prior to 2007)P/N: 65-0915-006Mounting Brackets2XM12x1.75x100 mm Bolt12XM13 Washer24X8.6.1M12x1.75 Nut12XSpacer4XChassis PreparationAttention: For precise drilling, use the mount plate bracket as a template to mark drilling locations.Driver side chassis frame shown below, repeat drill procedure on curb side.Chassis FrameBefore DrillingFront ofVehicleChassis Frame(Driver Side)2x ø20mmChassis FrameAfter Drilling2x ø12mmRear ofVehicleRev. 1.5- 28 -
MiniFix 1100/13208.6.2Installation ManualBracket Installation*SpacersM12NylockNutM13WasherChassis Frame(Driver Side)Mounting Bracket(Driver Side)*SpacersM12x100MMBoltM12x100MMBolt*NOTE: Spacers must be trimmedto the width of chassis frame.ChassisFrameMountingBracketWidth ofChassisFrameTorque SpecificationsM12 – 55 ft./lbs. (75 Nm)Rev. 1.5- 29 -
MiniFix 1100/13208.6.3Installation ManualLiftgate Installation1. Secure the MiniFix Mount Tube to the mounting brackets by bolting the sides of the mount tube tothe side of the brackets with the six (3 each side) M14 hardware provided with the liftgate.M14NutM14BoltM14NutM14BoltTorque SpecificationsM14 – 129 ft./lbs. (175 Nm)Rev. 1.5- 30 -
MiniFix 1100/13208.7Installation ManualMounting Bracket Kit – 128” Wheelbase, 35” Overhang(Vehicle Models After 2007)P/N: 65-0915-007Mounting Brackets2XM12x1.75x100 mm Bolt12XM13 Washer24X8.7.1M12x1.75 Nut12XSpacer4XChassis PreparationAttention: For precise drilling, use the mount plate bracket as a template to mark drilling locations.Driver side chassis frame shown below, repeat drill procedure on curb side.2x ø20mmOutsideWallChassis FramesBefore DrillingDrill2x ø12mmInsideWallChassis FramesAfter DrillingChassis Frame(Driver Side)255mm100mm50mmFront ofVehicleRear ofVehicleDrill2x ø12mm(Inside Wall)Drill2x ø20mm(Outside Wall)Chassis Frame; Drill DimensionsSide ViewRev. 1.5- 31 -
MiniFix 1100/13208.7.2Installation ManualBracket Installation*SpacersM12Nylock NutM13WasherChassis Frame(Driver Side)Mounting Bracket(Driver Side)M12x100mm*SpacersM12x100MMBolt*NOTE: Spacers must be trimmedto the width of chassis frame.ChassisFrameMountingBracket
contact Palfinger Liftgates at (888) 774-5844 Parts Order liftgateparts@palfinger.com Technical Support technicalapplications@palfinger.com PALFINGER Liftgates, LLC. 15939 Piuma Ave. Cerritos, CA 90703 Tel: (888) 774-5844 Fax: (562) 924-8318 PALFINGER Liftgates, LLC. 572 Whitehead Road. Trenton, NJ 08619 Tel: (609) 587-4200
PSI AP Physics 1 Name_ Multiple Choice 1. Two&sound&sources&S 1∧&S p;Hz&and250&Hz.&Whenwe& esult&is:& (A) great&&&&&(C)&The&same&&&&&
Argilla Almond&David Arrivederci&ragazzi Malle&L. Artemis&Fowl ColferD. Ascoltail&mio&cuore Pitzorno&B. ASSASSINATION Sgardoli&G. Auschwitzero&il&numero&220545 AveyD. di&mare Salgari&E. Avventurain&Egitto Pederiali&G. Avventure&di&storie AA.&VV. Baby&sitter&blues Murail&Marie]Aude Bambini&di&farina FineAnna
The program, which was designed to push sales of Goodyear Aquatred tires, was targeted at sales associates and managers at 900 company-owned stores and service centers, which were divided into two equal groups of nearly identical performance. For every 12 tires they sold, one group received cash rewards and the other received
College"Physics" Student"Solutions"Manual" Chapter"6" " 50" " 728 rev s 728 rpm 1 min 60 s 2 rad 1 rev 76.2 rad s 1 rev 2 rad , π ω π " 6.2 CENTRIPETAL ACCELERATION 18." Verify&that ntrifuge&is&about 0.50&km/s,∧&Earth&in&its& orbit is&about p;linear&speed&of&a .
theJazz&Band”∧&answer& musical&questions.&Click&on&Band .
Version 12.01.2018 v.LiNK Video-inserter VL3-MIB-4 . Read the manual prior to installation. Technical knowledge is necessary for installation. The . Audi Q7 (4M) MMI 7“ OFF OFF OFF OFF Porsche OFF OFF OFF OFF VW Touran OFF OFF OFF OFF Audi TT (8S) ON OFF .
6" syl 4" syl 12" swgl @ 45 & 5' o.c. 12" swchl 6" swl r1-1 ma-d1-6a 4" syl 4" syl 2' 2' r3-5r r4-7 r&d 14.7' 13' cw open w11-15 w16-9p ma-d1-7d 12' 2' w4-3 moonwalks abb r&d r&d r&d r&d r&d r&d ret ret r&d r&d r&d r&d r&d 12' 24' r&d ma-d1-7a ma-d1-7b ret r&d r&d r5-1 r3-2 r&d r&r(b.o.) r6-1r r3-2 m4-5 m1-1 (i-195) m1-1 (i-495) m6-2l om1-1 .
s& . o Look at the poem’s first and last lines (first and last lines may give readers important . it is important to read poems four times. Remind them that the first time they read is for enjoyment; rereads allow them to dive deeper into poems .
