21031502 Eagle Roofing High Profile Concrete Tile (2) DRAFT

DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)BOARD AND CODE ADMINISTRATION DIVISIONNOTICE OF ACCEPTANCE (NOA)MIAMI-DADE COUNTYPRODUCT CONTROL SECTION11805 SW 26 Street, Room 208Miami, Florida 33175-2474T (786) 315-2590 F (786) 315-2599www.miamidade.gov/economyEagle Roofing Products LLC1575 East C.R. 470Sumterville, FL 33585SCOPE:This NOA is being issued under the applicable rules and regulations governing the use of construction materials. Thedocumentation submitted has been reviewed and accepted by Miami-Dade County RER -Product Control Section to beused in Miami-Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section(in Miami-Dade County) and/or the AHJ (in areas other than Miami-Dade County) reserve the right to have this productor material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, themanufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the useof such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it isdetermined by Miami-Dade County Product Control Section that this product or material fails to meet the requirementsof the applicable building code.This product is approved as described herein, and has been designed to comply with the Florida Building Codeincluding the High Velocity Hurricane Zone of the Florida Building Code.DESCRIPTION:High Profile Concrete TileLABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and followingstatement: "Miami-Dade County Product Control Approved", unless otherwise noted herein.RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no changein the applicable building code negatively affecting the performance of this product.TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in thematerials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, forsales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section ofthis NOA shall be cause for termination and removal of NOA.ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by theexpiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be donein its entirety.INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors andshall be available for inspection at the job site at the request of the Building Official.This NOA renews NOA# 19-1030.04 and consists of pages 1 through 9.The submitted documentation was reviewed by Alex Tigera.NOA No. 21-0315.02Expiration Date: 10/05/26Approval Date: 05/06/21Page 1 of 9

ROOFING ASSEMBLY APPROVALCategory:Sub Category:Material:RoofingRoofing TilesConcrete1. SCOPE:This approves a new roofing system using High Profile Concrete Tile as manufactured by Eagle Roofing ProductsLLC in Sumterville, FL and described in Section 2 of this Notice of Acceptance. For use in locations where thepressure requirements, as determined by applicable Building Code, do not exceed the design pressure valuesobtained by calculations in compliance with RAS 127 using the values listed in section 4 herein. The attachmentcalculations shall be done as a moment based system.2. PRODUCT DESCRIPTION:Manufactured riptionLenght 17"Width 12 ¼"Thickness ½"TAS 112Type 1aClass IIIHigh profile concrete roof tile. For direct deck orbattened nail-on applications.Lenght variesWidth variesvarying thicknessTAS 112Accessory trim, concrete roof pieces for use athips, rakes, ridges and valley terminations.Manufactured for each tile profile.High Profile Concrete TileTrim Pieces2.1 PRODUCTS MANUFACTURED BY OTHERSProduct NameProduct DescriptionICP Adhesives Polyset AH-160Two component polyurethanefoam adhesive.TILE BONDTM Roof Tile AdhesiveSingle component polyurethanefoam roof tile adhesive.Two component polyurethanefoam adhesive.DAP Foam Touch N SealStormBond 2 Roof Tile AdhesiveManufacturer(With Current NOA)ICP Adhesives and Sealants, Inc.DuPont de Nemours, Inc.DAP Foam, Inc.2.2 MANUFACTURING LOCATION2.2.1. Sumterville, FLNOA No. 21-0315.02Expiration Date: 10/05/26Approval Date: 05/06/21Page 2 of 9

2.3 EVIDENCE SUBMITTED:Test AgencyTest IdentifierTest Name/ReportDatePRI Asphalt TechnologiesERPF-001-02-03TAS-112Aug. 2006Redland Technologies7161-03Appendix IIIStatic Uplift TestingTAS 102 & 102(A)Dec. 1991Redland TechnologiesLetter Dated Aug. 1,1994Wind Tunnel TestingTAS 108 (Nail-On)Aug. 1994Redland TechnologiesP09647-01Wind Tunnel TestingTAS 108 (Mortar Set)Aug. 1994Redland TechnologiesP0402Withdrawal Resistance Testing of screwvs. smooth shank nailsSept. 1993The Center for AppliedEngineering, Inc.94-083Static Uplift TestingTAS 101 (Adhesive Set)April 1994The Center for AppliedEngineering, Inc.94-084Static Uplift TestingTAS 101 (Mortar Set)May 1994The Center for AppliedEngineering, Inc.25-7094-(3, 6 & 9)Static Uplift TestingTAS 102Oct. 1994The Center for AppliedEngineering, Inc.25-7120-(1 & 2)Static Uplift TestingTAS 102Nov. 1994The Center for AppliedEngineering, Inc.25-7183-(3 & 4)Static Uplift TestingTAS 102Feb. 1995The Center for AppliedEngineering, Inc.25-7214-(3, 4, &7)Static Uplift TestingTAS 102March, 1995The Center for AppliedEngineering, Inc.25-7804-4Static Uplift TestingTAS 102Sep. 1996Celotex CorporationTesting Services520111-3Static Uplift TestingTAS 101Dec. 1998Celotex CorporationTesting Services520191-2-1Static Uplift TestingTAS 101March 1999Walker Engineering, Inc.CalculationsAerodynamic MultiplierSep. 2006RT0317.03-21TAS-11203/27/21PRI Construction 4Static Uplift Testing(Adhesive)TAS 10111/30/1707/09/1807/09/18NEMO ETC, LLC4c-DPBS-20LSOTM-01.D.R1TAS 10112/17/20ATL of South FloridaNOA No. 21-0315.02Expiration Date: 10/05/26Approval Date: 05/06/21Page 3 of 9

3.LIMITATIONS:3.1 Fire classification is not part of this acceptance.3.2 For mortar or adhesive set tile applications, a static field uplift test in accordance with TAS 106 shall berequired, refer to applicable Building Code.3.3 Applicant shall retain the services of a Miami-Dade County Certified Laboratory to perform quarterly test inaccordance with TAS 112, appendix ‘A’. Such testing shall be submitted to the Miami-Dade CountyProduct Control Section for review.3.4 Minimum underlayment shall be in compliance with the applicable Roofing Applications Standards listedsection 4.1 herein.3.5 30/90 hot mopped underlayment applications may be installed perpendicular to the roof slope unless statedotherwise by the underlayment material manufacturers published literature.3.6 This acceptance is for wood deck applications. Minimum deck requirements shall be in compliance withapplicable Building Code.3.7 All products listed herin shall have aquality assurance audit in accordance with the Florida Building Codeand Rule 61G20-3 of the Florida Administrative Code.4.INSTALLATION4.1Eagle Roofing Products LLC, High Profile Concrete Tile and its components shall be installed in strictcompliance with Roofing Application Standard RAS 118, RAS 119 and RAS 120.Data For Attachment Calculations:4.2Table 1: Average Weight (W) and Dimensions (l x w )Tile ProfileWeight-W (lbf)Length-l (ft)Width-w (ft)101.4171.04High Profile Concrete TileTable 2: Aerodynamic Multipliers - λ (ft3)TileProfileλ (ft3)Batten Applicationλ (ft3)Direct Deck Application0.3000.277High Profile Concrete TileTable 3: Restoring Moments due to Gravity - Mg (ft-lbf)TileProfileHigh ProfileConcrete Tile2" & attens6.287":12"or greaterDirectDeck6.56Battens6.10DirectDeck6.38NOA No. 21-0315.02Expiration Date: 10/05/26Approval Date: 05/06/21Page 4 of 9

Table 4: Attachment Resistance Expressed as a Moment - Mf (ft-lbf)for Nail-On SystemsTileProfileFastener TypeDirect Deck(min 15/32” plywood)Direct Deck(min. 19/32” plywood)BattensHigh ProfileConcrete Tile2-10d Ring Shank Nails1-10d Smooth or ScrewShank Nail2-10d Smooth or ScrewShank Nails1 #8 Screw2 #8 Screw1-10d Smooth or ScrewShank Nail (Field Clip)1-10d Smooth or ScrewShank Nail (Eave Clip)2-10d Smooth or ScrewShank Nails (Field Clip)2-10d Smooth or ScrewShank Nails (Eave 8.141.82-10d Ring Shank Nails133.148.11. Installation with a 4" tile headlap and fasteners are located a min. of 2½“from head of tile.45.2Table 5: Attachment Resistance Expressed as a Moment Mf (ft-lbf)for Two Patty Adhesive Set SystemsTile Application1Minimum AttachmentResistanceDupont De Nemours TILE BOND TM Roof Tile AdhesiveDupont De Nemours TILE BOND TM Roof Tile AdhesiveICP Adhesives Polyset AH-160DAP Foam Touch N Seal StormBond 2 Roof Tile Adhesive19 258 329.3 449 5TileProfileHigh Profile Concrete Tile12345See manufactures component approval for installation requirements.Dupont De Nemours TILE BOND TM Roof Tile Adhesive weight per patty 8 grams.Dupont De Nemours TILE BOND TM Roof Tile Adhesive weight per patty 10 and 20 grams.ICP Adhesives Polyset AH-160 weight per patty 8 grams.DAP Foam Touch N Seal StormBond 2 Roof Tile Adhesive weight per paddy 8 grams.*NOTE *For # 2 placement see Detail 3 B on page 8 of 9For # 3 placement see Detail 3 C on page 9 of 9NOA No. 21-0315.02Expiration Date: 10/05/26Approval Date: 05/06/21Page 5 of 9

Table 6: Attachment Resistance Expressed as a Moment - Mf (ft-lbf)for Single Patty Adhesive Set SystemsTile Application6Minimum AttachmentResistanceICP Adhesives Polyset AH-160ICP Adhesives Polyset AH-160DAP Foam Touch N Seal StormBond 2 Roof Tile AdhesiveDAP Foam Touch N Seal StormBond 2 Roof Tile Adhesive66.5 738.7 861 937 10TileProfileHigh Profile Concrete TileSee manufactures component approval for installation requirements.ICP Adhesives Polysetq AH-160 Large paddy placement of 63 grams.8 ICP Adhesives Polysetq AH-160 Medium paddy placement of 24 grams.9 DAP Foam Touch N Seal StormBond 2 Roof Tile Adhesive weight per paddy 60 grams.10 DAP Foam Touch N Seal StormBond 2 Roof Tile Adhesive weight per paddy 30 grams.67Table 7: Attachment Resistance Expressed as a Moment - Mf (ft-lbf)for Mortar Set SystemsTileProfileHigh Profile Concrete TileTileApplicationAttachmentResistanceMortar Set1124.511 Tile-Tite Roof Tile Mortar.5. LABELING :All tiles shall bear the imprint or identifiable marking of the manufacturer's name or logo (SeeDetail Below), or following statement: "Miami-Dade County Product Control Approved".(LOCATED ON UNDERSIDE OF TILE)OREAGLE FL(LOCATED ON FRONTSIDE OF TILE)NOA No. 21-0315.02Expiration Date: 10/05/26Approval Date: 05/06/21Page 6 of 9

6. BUILDING PERMIT REQUIREMENTS:6.1 Application for building permit shall be accompanied by copies of the following:6.1.1 This Notice of Acceptance.6.1.2 Any other documents required by AHJ or applicable Building Code in order to properly evaluate theinstallation of this system.PROFILE DRAWINGHIGH PROFILE CONCRETE TILENOA No. 21-0315.02Expiration Date: 10/05/26Approval Date: 05/06/21Page 7 of 9

DETAIL 3 BNOA No. 21-0315.02Expiration Date: 10/05/26Approval Date: 05/06/21Page 8 of 9

DETAIL 3 CEND OF THIS ACCEPTANCENOA No. 21-0315.02Expiration Date: 10/05/26Approval Date: 05/06/21Page 9 of 9

NOA No. 21-0315.02 Expiration Date: 10/05/26 Approval Date: 05/06/21 Page 2 of 9 ROOFING ASSEMBLY APPROVAL Category: Roofing Sub Category: Roofing Tiles Material: Concrete 1. SCOPE: This approves a new roofing system using High Profile Concrete Tile as manufactured by Eagle Roofing Products LLC in Sumterville, FL and described in Section 2 of this Notice of Acceptance.