21031504 Eagle Roofing Medium Profile Concrete Tile - Miami-Dade County

1y ago
21 Views
2 Downloads
773.71 KB
10 Pages
Last View : 1d ago
Last Download : 2m ago
Upload by : Callan Shouse
Transcription

MIAMI-DADE COUNTYDEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)BOARD AND CODE ADMINISTRATION DIVISIONNOTICE OF ACCEPTANCE (NOA)PRODUCT CONTROL SECTION11805 SW 26 Street, Room 208Miami, Florida 33175-2474T (786) 315-2590 F (786) 315-2599www.miamidade.gov/economyEagle Roofing Products LLC1575 East C.R. 470Sumterville, FL 33585SCOPE:This NOA is being issued under the applicable rules and regulations governing the use of construction materials. Thedocumentation submitted has been reviewed and accepted by Miami-Dade County RER -Product Control Section to beused in Miami-Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section(in Miami-Dade County) and/or the AHJ (in areas other than Miami-Dade County) reserve the right to have this productor material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, themanufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the useof such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it isdetermined by Miami-Dade County Product Control Section that this product or material fails to meet the requirementsof the applicable building code.This product is approved as described herein, and has been designed to comply with the Florida Building Codeincluding the High Velocity Hurricane Zone of the Florida Building Code.DESCRIPTION:Medium Profile Concrete TileLABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and followingstatement: "Miami-Dade County Product Control Approved", unless otherwise noted herein.RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no changein the applicable building code negatively affecting the performance of this product.TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in thematerials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, forsales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section ofthis NOA shall be cause for termination and removal of NOA.ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by theexpiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be donein its entirety.INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors andshall be available for inspection at the job site at the request of the Building Official.This NOA renews NOA# 19-1030.06 and consists of pages 1 through 10.The submitted documentation was reviewed by Alex Tigera.NOA No. 21-0315.04Expiration Date: 10/05/26Approval Date: 05/06/21Page 1 of 10

ROOFING ASSEMBLY APPROVALCategory:Sub Category:Material:RoofingRoofing TilesConcrete1. SCOPE:This approves a system using Eagle Roofing Products Medium Profile Concrete Tile, as manufacturedby Eagle Roofing Products LLC in Sumterville, FL and described in Section 2 of this Notice ofAcceptance. For use in locations where the pressure requirements, as determined by applicable BuildingCode, do not exceed the design pressure values obtained by calculations in compliance with RAS 127using the values listed in section 4 herein. The attachment calculations shall be done as a moment basedsystem.2. PRODUCT DESCRIPTION:Manufactured byApplicantMedium Profile ConcreteTileTrim onLenght 17"Width 12 ½"Thickness ½"TAS 112Type 1bClass IIILow profile, interlocking, high pressure extrudedconcrete roof tile equipped with three nail holeand double roll ribs. For direct deck or battenednail-on, mortar or adhesive set applications.Lenght variesWidth variesvarying thicknessTAS 112Accessory trim, concrete roof pieces for use athips, rakes and ridges. Manufactured for each tileprofile.2.1 PRODUCTS MANUFACTURED BY OTHERSProduct NameProduct DescriptionPolyset AH-160Two component polyurethanefoam adhesive.TILE BONDTM Roof Tile AdhesiveSingle component polyurethanefoam roof tile adhesive.Touch ‘N Seal StormBond 2 TwoComponent Polyurethane Roof TileAdhesiveTwo component polyurethanefoam adhesive.Manufacturer(With Current NOA)ICP Adhesives and Sealants, Inc.DuPont de Nemours, Inc.DAP Foam, Inc.2.2 MANUFACTURING LOCATION2.2.1. Sumterville, FLNOA No. 21-0315.04Expiration Date: 10/05/26Approval Date: 05/06/21Page 2 of 10

2.3 EVIDENCE SUBMITTED:Test AgencyTest IdentifierTest Name/ReportDatePRI ConstructionMaterials TechnologiesERPF-001-02-02TAS 112Aug. 2006Redland Technologies7161-03Appendix IIIStatic Uplift TestingTAS 102 & TAS 102(A)Dec. 1991Redland Technologies7161-03Appendix IIWind Tunnel TestingTAS 108 (Nail-On)Dec. 1991Redland TechnologiesP0402Withdrawal Resistance Testing ofscrew vs. smooth shank nailsSept. 1993The Center for AppliedEngineering, Inc.94-060BStatic Uplift TestingTAS 101 (Adhesive Set)March, 1994The Center for AppliedEngineering, Inc.94-084Static Uplift TestingTAS 101 (Mortar Set)May 1994Redland TechnologiesP0631-01Wind Tunnel TestingTAS 108 (Mortar Set)July 1994Redland TechnologiesLetter Dated Aug. 1,1994Wind Tunnel TestingTAS 108 (Nail-On)Aug. 1994Professional ServiceIndustries, Inc.224-47099Physical PropertiesTAS 112Sept. 1994The Center for AppliedEngineering, Inc.25-7094-1Static Uplift TestingTAS 102(4" Headlap, Nails, Direct Deck, NewConstruction)Oct. 1994The Center for AppliedEngineering, Inc.25-7094-7Static Uplift TestingTAS 102(4" Headlap, Nails, Battens)Oct. 1994The Center for AppliedEngineering, Inc.25-7094-4Static Uplift TestingTAS 102(4" Headlap, Nails, Direct Deck,Recover/Reroof)Oct. 1994The Center for AppliedEngineering, Inc.Project No. 307025Test #MDC-76Wind Driven RainTAS 100Oct. 1994The Center for AppliedEngineering, Inc.25-7183-1Static Uplift TestingTAS 102(2 Quik-Drive Screws, Direct Deck)Feb. 1995The Center for AppliedEngineering, Inc.25-7183-2Static Uplift TestingTAS 102(2 Quik-Drive Screws, Battens)Feb. 1995The Center for AppliedEngineering, Inc.25-7214-225-7214-6Static Uplift TestingTAS 102(1 Quik-Drive Screw, Direct Deck)(1 Quik-Drive Screw, Battens)March, 1995NOA No. 21-0315.04Expiration Date: 10/05/26Approval Date: 05/06/21Page 3 of 10

Celotex CorporationTesting Services528454-2-1520109-2Static Uplift TestingTAS 101Sep. 1998Dec. 1998Walker Engineering, onCalculationsTwo Patty Adhesive Set SystemApril 199925-7183March 199525-7094February 199625-7496April 199625-758425-7804b-825-7804-4 & 525-7848-6December 1996Walker Engineering, Inc.CalculationsAerodynamic MultiplierSep. 2006Walker Engineering, Inc.CalculationsRestoring Moment Due to GravitySep. 2006ATL of South FloridaRT0317.01-21TAS 11203/27/21PRI Constructionmaterials 2-03TAS 101 (2 PD )TAS 101 (LRG)TAS 101 (MED)11/30/1704/06/1804/06/18NEMO ETC, LLC4c-DPBS-20LSOTM-01.D.R1TAS 10112/17/20Walker Engineering, Inc.Walker Engineering, Inc.Walker Engineering, Inc.Walker Engineering, Inc.3. LIMITATIONS:3.1 Fire classification is not part of this acceptance.3.2 For mortar or adhesive set tile applications, a static field uplift test in accordance with TAS 106 shall berequired, refer to applicable Building Code.3.3 Applicant shall retain the services of a Miami-Dade County Certified Laboratory to perform quarterly test inaccordance with TAS 112, appendix ‘A’. Such testing shall be submitted to the Miami-Dade County ProductControl Section for review.3.4 Minimum underlayment shall be in compliance with the applicable Roofing Applications Standards listedsection 4.1 herein.3.5 30/90 hot mopped underlayment applications may be installed perpendicular to the roof slope unless statedotherwise by the underlayment material manufacturers published literature.3.6 This acceptance is for wood deck applications. Minimum deck requirements shall be in compliance withapplicable Building Code.3.7 All products listed herein shall have a quality assurance audit in accordance with the Florida Building Codeand Rule 61G20-3 of the Florida Administrative Code.NOA No. 21-0315.04Expiration Date: 10/05/26Approval Date: 05/06/21Page 4 of 10

4.INSTALLATION4.1Eagle Roofing Products LLC, Medium Profile Concrete Tile and its components shall be installed in strictcompliance with Roofing Application Standard RAS 118, RAS 119 and RAS 120.Data For Attachment Calculations:4.2Table 1: Average Weight (W) and Dimensions (l x w )Tile ProfileWeight-W (lbf)Length-l (ft)Width-w (ft)9.51.4171.04Medium Profile Concrete TileTable 2: Aerodynamic Multipliers - λ (ft3)TileProfileλ (ft3)Batten Applicationλ (ft3)Direct Deck Application0.3050.282Medium Profile Concrete TileTable 3: Restoring Moments due to Gravity - Mg (ft-lbf)TileProfileMedium ProfileConcrete Tile2" & attens5.937":12"or e 4: Attachment Resistance Expressed as a Moment - Mf (ft-lbf)for Nail-On SystemsTileProfileFastener TypeDirect Deck(min 15/32” plywood)Direct Deck(min. 19/32” plywood)BattensMedium ProfileConcrete Tile2-10d Ring Shank Nails1-10d Smooth or ScrewShank Nail2-10d Smooth or ScrewShank Nails1 #8 Screw2 #8 Screw1-10d Smooth or ScrewShank Nail (Field Clip)1-10d Smooth or ScrewShank Nail (Eave Clip)2-10d Smooth or ScrewShank Nails (Field Clip)2-10d Smooth or ScrewShank Nails (Eave .931.932.212-10d Ring Shank Nails143.067.5Installation with a 4" tile headlap and fasteners are located a min. of 2½“from head of tile.50.9NOA No. 21-0315.04Expiration Date: 10/05/26Approval Date: 05/06/21Page 5 of 10

Table 5: Attachment Resistance Expressed as a Moment Mf (ft-lbf)for Two Patty Adhesive Set SystemsTile Application2Minimum AttachmentResistanceDupont De Nemours TILE BOND TM Roof Tile AdhesiveDupont De Nemours TILE BOND TM Roof Tile AdhesiveICP Adhesives Polyset AH-160DAP Foam Touch N Seal StormBond 2 Roof Tile Adhesive35 367 426.1 5101 6TileProfileMedium Profile ConcreteTile23456See manufactures component approval for installation requirements.Dupont De Nemours TILE BOND TM Roof Tile Adhesive weight per patty 8 grams.Dupont De Nemours TILE BOND TM Roof Tile Adhesive weight per patty 16 grams.ICP Adhesives Polyset AH-160 weight per patty 8 grams.DAP Foam Touch N Seal StormBond 2 Roof Tile Adhesive weight per paddy 8 grams.*NOTE *For # 3 placement see Detail 2 A on page 9 of 10For # 4 placement see Detail 2 B on page 10 of 10Table 6: Attachment Resistance Expressed as a Moment - Mf (ft-lbf)for Single Patty Adhesive Set SystemsTile Application7Minimum AttachmentResistanceICP Adhesives Polyset AH-160ICP Adhesives Polyset AH-160DAP Foam Touch N Seal StormBond 2 Roof Tile AdhesiveDAP Foam Touch N Seal StormBond 2 Roof Tile Adhesive86.6 845.5 954 1061 11TileProfileMedium Profile ConcreteTileSee manufactures component approval for installation requirements.ICP Adhesives Polysetq AH-160 Large paddy placement of 54 grams.9 ICP Adhesives Polysetq AH-160 Medium paddy placement of 24 grams.10 DAP Foam Touch N Seal StormBond 2 Roof Tile Adhesive weight per paddy 30 grams.11 DAP Foam Touch N Seal StormBond 2 Roof Tile Adhesive weight per paddy 60 grams.78Table 7: Attachment Resistance Expressed as a Moment - Mf (ft-lbf)for Mortar Set SystemsTileProfileMedium Profile Concrete Tile12 Tile-Tite Roof Tile Mortar.TileApplicationAttachmentResistanceMortar Set1220.6NOA No. 21-0315.04Expiration Date: 10/05/26Approval Date: 05/06/21Page 6 of 10

5. LABELING :All tiles shall bear the imprint or identifiable marking of the manufacturer's name or logo (SeeDetail Below), or following statement: "Miami-Dade County Product Control Approved".(LOCATED ON UNDERSIDE OF TILE)OREAGLE FL(LOCATED ON FRONTSIDE OF TILE)6. BUILDING PERMIT REQUIREMENTS:6.1 Application for building permit shall be accompanied by copies of the following:6.1.1 This Notice of Acceptance.6.1.2 Any other documents required by AHJ or applicable Building Code in order to properly evaluate theinstallation of this system.NOA No. 21-0315.04Expiration Date: 10/05/26Approval Date: 05/06/21Page 7 of 10

PROFILE DRAWINGNOA No. 21-0315.04Expiration Date: 10/05/26Approval Date: 05/06/21Page 8 of 10

DETAIL 2 ANOA No. 21-0315.04Expiration Date: 10/05/26Approval Date: 05/06/21Page 9 of 10

DETAIL 2 BMEDIUM PROFILE CONCRETE ROOF TILEEND OF THIS ACCEPTANCENOA No. 21-0315.04Expiration Date: 10/05/26Approval Date: 05/06/21Page 10 of 10

NOA No. 21-0315.04 Expiration Date: 10/05/26 Approval Date: 05/06/21 Page 2 of 10 ROOFING ASSEMBLY APPROVAL Category: Roofing Sub Category: Roofing Tiles Material: Concrete 1. SCOPE: This approves a system using Eagle Roofing Products Medium Profile Concrete Tile, as manufactured by Eagle Roofing Products LLC in Sumterville, FL and described in Section 2 of this Notice of

Related Documents:

ORIGINAL ROOF TILE . Manufacturer: Eagle Roofing Products Manufacturer: Eagle Roofing Products Manufacturer: Eagle Roofing Products Manufacturer: Eagle Roofing Products Manufacturer: Eagle Roofing Products Manufacturer: Sherwin Williams Page 1 of 4 Updated: 3/11/2018 .

Eagle II, Golden Eagle II, & Directional Golden Eagle II (Eagle 3 has Yr 3 included): 3rd Year Warranty (444-0002-03) 1 Each 30 days 227.00 39 Kustom Signals, Inc. Eagle II, Golden Eagle II, Directional Golden Eagle II & Eagle 3: 4th Year Warranty (444-0002-04) 1 Each 30 days 252.00 40 Kustom Signals, Inc. Eagle II, Golden Eagle II .

NOA No. 21-0315.03 Expiration Date: 10/05/26 Approval Date: 05/06/21 Page 2 of 11 ROOFING ASSEMBLY APPROVAL Category: Roofing Sub Category: Roofing Tiles Material: Concrete 1. SCOPE: This approves a new roofing system using "Low Profile Concrete Tile" as manufactured by Eagle Roofing Products LLC in Sumterville, FL and described in Section 2 of this Notice of Acceptance.

NOA No. 21-0315.02 Expiration Date: 10/05/26 Approval Date: 05/06/21 Page 2 of 9 ROOFING ASSEMBLY APPROVAL Category: Roofing Sub Category: Roofing Tiles Material: Concrete 1. SCOPE: This approves a new roofing system using High Profile Concrete Tile as manufactured by Eagle Roofing Products LLC in Sumterville, FL and described in Section 2 of this Notice of Acceptance.

Rain Bird Part Number: For Eagle 900/950 — Part #D02203, Model: SRP For Eagle 700/750, 500/550 — Part #D02236, Model: SR-700 4. Selector valve key — used to manually operate and service electric Eagle Rotors. Rain Bird Part Number: For Eagle 900/950, 700/750, 500/550 — Part #B41720, Model: EGL-SVK

1. Roofing system 1 2. Requirement of roofing material 1 3. Metal roofing 1 4. Classification of metal roofing 2 5. Merits of self supported roofing system 3 6. Material and technology 3 7. Specification of galvalume sheet 4 8. Primary sheeting material 4 9. Present systems of self supported roofing 5 10.

Apr 20, 2016 · Marine & Freshwater Finfish Aquaculture Low Medium Medium Medium Dams Low Medium Medium Medium Logging & Wood Harvesting (Timber Production) High Medium Medium Oil Spills Medium Medium Medium Medium Marine shellfish aquaculture

Required Texts: Harris, Ann Sutherland. Seventeenth Century Art and Architecture, 1st or 2nd edition will work, only 2nd edition available in book store Harr, Jonathan. The Lost Painting: The Quest for a Caravaggio Masterpiece. Optional Text: Scotti, R.A. Basilica: The Splendor and the Scandal: The Building of St. Peters’s; Barnett, Sylvan.