Hardware Manual - Textfiles
HDWRCV2.QXD5/18/98 5:01 PMPage 1Hardware Manual82400INS03
HDWRCV2.QXD5/18/98 5:01 PMPage 2This manual has been developed by Nitsuko America. It is intendedfor the use of its customers and service personnel, and should beread in its entirety before attempting to install or program the system. Any comments or suggestions for improving this manualwould be appreciated. Forward your remarks to:Nitsuko America, Telecom Division4 Forest ParkwayShelton, CT 06484Attention: Manager, Technical PublicationsNothing contained in this manual shall be deemed to be, and thismanual does not constitute, a warranty of, or representation withrespect to, any of the equipment covered. This manual is subject tochange without notice and Nitsuko America has no obligation to provide any updates or corrections to this manual. Further, NitsukoAmerica also reserves the right, without prior notice, to makechanges in equipment design or components as it deems appropriate. No representation is made that this manual is complete oraccurate in all respects and Nitsuko America shall not be liable forany errors or omissions. In no event shall Nitsuko America be liablefor any incidental or consequential damages in connection with theuse of this manual. This document contains proprietary informationthat is protected by copyright. All rights are reserved. No part ofthis document may be photocopied or reproduced without prior written consent of Nitsuko America. 1998 by Nitsuko America. All Rights Reserved.Printed in U.S.A.
HDWR1A.QXD5/18/98 4:48 PMPage 11. INSTALLING THE MAIN CABINETSection 1Installing the Main CabinetsIn this section . . .PageInstalling the Cabinets . . . . . . . . . . . . . . .1-3Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3Before Installing . . . . . . . . . . . . . . . . . . . . . . 1-3Site Requirements . . . . . . . . . . . . . . . . . . . . . 1-3Removing the Cover . . . . . . . . . . . . . . . . . . . 1-4Mounting the Cabinet . . . . . . . . . . . . . . . . . . 1-4Grounding the Cabinet . . . . . . . . . . . . . . .1-6Connecting the Ground Wires. . . . . . . . . . . . 1-61-1
HDWR1A.QXD1-25/18/98 4:48 PMPage 2
HDWR1A.QXD5/18/98 4:48 PMPage 3INSTALLING THE CABINETUnpackingUnpack the equipment and check it against your equipment lists. Inspect for physical damage.Have the appropriate tools for the job on hand, including: a test set, a punch down tool and a digital voltmeter.Before InstallingMake sure you have a building plan showing the location of the common equipment, extensions, the telcodemarcation and earth ground. In addition, the installation site must meet the requirements outlined in theStandard Practices Manual.Site RequirementsThe common equipment is contained in a wall-mountedcabinet: the Main Cabinet. Choose a central location forthe cabinet that allows enough space for the equipment— and provides enough room for you to comfortablywork. The Installation Layout (Figure 1-2 on page 1-5)shows you approximately how much space your systemrequires.The common equipment cabinet requires a three-prongdedicated 117 VAC 60 Hz circuit (NEMA 5-15 receptacle) located within 6 feet of the AC receptacle. Youshould install the extension block to the right of theMain Cabinet. Telco should install the RJ11C to theleft of the Main Cabinet.1-3
HDWR1A.QXD5/18/98 4:48 PMPage 4INSTALLING THE CABINETRemoving the Cover (Figure 1-1)To make wall-mounting easier, remove the cover on thecommon equipment cabinet. This allows you to use thecabinet as a mounting template.1. Unscrew the two captive screws on the lower half ofthe cabinet cover.2. Lift up the lower half of the cover — then slide thecover back slightly to remove it.ScrewsTop CoverBase Unit93 00 0- 8Figure 1-1 REMOVING THE COVERMounting the Cabinet (Figure 1-2)1. Using suitable fasteners, mount a Main DistributionFrame (MDF) plywood backboard in a centrallylocated spot.2. Hold the Main Cabinet against the MDF and markall four mounting holes.3. Drill the marked holes using a 1/8” drill bit.4. Install two mounting screws (provided) in the top twoholes, leaving about 3/8” shank exposed.5. Hang the Main Cabinet on the top two screws andfasten in place.6. Install the bottom two screws and tighten in place.1-4
HDWR1A.QXD5/18/98 4:49 PMPage 5INSTALLING THE CABINET82400 - 13FOF1250V6.3A250V6.3AFigure 1-2 INSTALLATION LAYOUT1-5
HDWR1A.QXD5/18/98 4:49 PMPage 6GROUNDING THE CABINETConnecting the Ground Wires (Figure 1-3)The cabinet is grounded at the ETH (Earth Ground)connection.1. Loosen the lug on the ground connection.2. Using a piece of 12 AWG stranded copper wire, connect the ETH to the ground connector.3. Insert 12 AWG stranded copper wire into thegrounding terminal on the outside of the cabinet.Firmly tighten the connection.4. Connect the grounding cable to a known earthground.2CO/8STA PCBFOF1250V6.3A250V6.3ACPUPFCONETH82400 - 37FGETH/SGCOCNAC CordGroundingCableScrewFigure 1-3 GROUNDING A CABINETNow that your cabinet is installed and grounded, go toPart 2: PCB Installation and Startup.DO NOT PLUG IN THE CABINET POWER CORDWITHOUT FIRST INSTALLING THE PCBS.1-6
HDWR1B.QXD5/18/98 4:51 PMPage 12. PCB INSTALLATION AND STARTUPSection 2PCB Installation and StartupIn this section . . .PagePCB Location . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3Where to Install the PCBs . . . . . . . . . . . . . . . . . . .2-3Installing PCBs . . . . . . . . . . . . . . . . . . . . . . . . .2-4Central Processing Unit (CPU) PCB . . . . . . . . . . .2-4Expansion (2CO/8STA) PCB . . . . . . . . . . . . . . . .2-6Ring Generator PCB . . . . . . . . . . . . . . . . . . . . . . .2-7Auxiliary PCB . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8Power Failure (4 PF XFER) PCB . . . . . . . . . . . . .2-9SMDR PCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10SMDR RS-232C Cable Assembly . . . . . . . . . . . .2-11Powering Up the System . . . . . . . . . . . . . . . . .2-12Power-Up Sequence . . . . . . . . . . . . . . . . . . . . . . .2-122-1
HDWR1B.QXD2-25/18/98 4:51 PMPage 2
HDWR1B.QXD5/18/98 4:51 PMPage 3PCB LOCATIONWhere to Install the PCBs (Figure 2-1)Maximum Configuration:8 Trunks24 ExtensionsLithium Battery2 CO/8 STA PCBCPUSMDR PCB or Caller ID PCB82400 - 35Auxillary PCBFOF1250V6.3A250V6.3A4 PF XFER PCBPFCONCOCNCOCNPFSTNSLTCNSTCNRGUCNRing Generator PCBRS-232-C Jack and Cable AssemblyFigure 2-1 PCB LOCATION2-3
HDWR1B.QXD5/18/98 4:51 PMPage 4INSTALLING PCBsCentral Processing Unit (CPU) PCB (Figure 2-2)Battery82400 - 36Station 8Station 1Trunk 1Trunk 2Trunk 3Station 7Station 2Station 3Station 6Station 5Station 4Trunk 4Figure 2-2 CPU PCBThe CPU PCB comes already installed in the Main Cabinet.The CPU provides: The system’s central processing, stored program and memory for the customer’s site-specific data. Mode switch for cold (default data) or warm (customerdata) start on power-up. Battery for backup of the customer’s site-specific data. Useonly a SONY CR2032 Lithium Battery or equivalent.Replace the battery when “B” flashes on the display of thekey telephones. The battery’s life is between 3.5 and 7years - depending on how often the system is powereddown. The more the system’s power is off, the shorter thebattery’s life. Connection points for the CO and station DDK connectors.2-4
HDWR1B.QXD5/18/98 4:51 PMPage 5INSTALLING PCBsTo prepare the CPU PCB:1. Slide the Switch-1 (top switch) to the INT (left) position.This ensures that the system will load the default database on initial power-up.2. Power the system up.3. After the system has been powered up for a minimum of10 seconds, insert the battery into the battery clips.The printing on the battery should be facing up so thatit is visible when installed.4. Slide the Switch-1 (top) to the RUN position (to the right).Note: NEVER move the switch unless the intent is to clearall programmed memory.Refer to Part 4, Installing Optional Equipment for instructions on installing Background Music and Music on Hold.2-5
HDWR1B.QXD5/18/98 4:51 PMPage 6INSTALLING PCBsExpansion (2CO/8STA) PCB (Figure 2-3)2CO/8STA PCBETH82400-19CPUFigure 2-3 EXPANSION (2CO/8STA) PCBThe Expansion (2CO/8STA) PCB provides DDK connectorsfor two additional CO lines and eight additional telephones.To install a 2CO/8STA PCB:1. Place the 2CO/8STA PCB on top of the CPU. Align theEXPCN female connector on the bottom of the 2CO/8STAPCB over the EXPCN male connector on the PCB below.Push down firmly on the expansion PCB to ensure that theEXPCN connectors are firmly together. Using the additional spacers included with the 2CO/8STA PCB, attachthe PCB to the card below.2. Connect the green earth ground lead terminal to the ETHscrew on the CPU. An earth ground is always required.3. Refer to Part 3: Installing Extensions and Trunks forcabling instructions.4. If installing a second Expansion PCB, simply place thecard over the first PCB and repeat steps 1-3.5. To install an Expansion PCB if an SMDR or Power FailurePCB has been previously installed: Power down the system Remove the SMDR and/or Power Failure PCB Install the Expansion PCB Reinstall the SMDR and/or Power Failure PCBs Power up the system.2-6
HDWR1B.QXD5/18/98 4:51 PMPage 7INSTALLING PCBsRing Generator PCB (Figure 2-4)CPURing GeneratorPCBCPU82400- 32RGUCNFigure 2-4 RING GENERATOR PCBThe Ring Generator PCB provides the ring generator sourcewhen connecting a single line telephone, modem, voice mail,or answering machine as a system extension. This must beinstalled when any single line telephones are used in the system.To install a Ring Generator PCB:1. Align the PCB on the left side of the Main Cabinet, belowthe power switch. Using the three screws provided, attachthe PCB to the Main Cabinet.2. Attach the cable from the Ring Generator PCB to the connector labeled RGUCN mounted on the CPU.2-7
HDWR1B.QXD5/18/98 4:51 PMPage 8INSTALLING PCBsAuxiliary PCB (Figure 2-5)Volume ControlVR2 VR1 VR4 VR32CO/8STA PCBCard Holder82400-20CPUFigure 2-5 AUXILIARY PCBThe Auxiliary PCB provides: 2-pin DDK connectors for two External Paging Zones. 2-pin DDK connectors for two Door Boxes. 2-pin DDK connectors for two common-use relay contacts. 2-pin DDK connectors for Background Music source. 2-pin DDK connectors for Music On Hold source.To install an Auxiliary PCB:1. Insert the two card holders (included with the PCB) intothe outer holes on the right-hand side of the Main Cabinet.2. Insert the Auxiliary PCB into the card holders.3. Connect the ribbon cable (included with the PCB) to theAuxiliary PCB and then to the DHUCN connector on theCPU.4. Refer to Part 4: Installing Optional Equipment for moreon installing Door Boxes, External Paging Equipment andAlarm Sensors.2-8
HDWR1B.QXD5/18/98 4:51 PMPage 9INSTALLING PCBsPower Failure (4 PF XFER) PCB (Figure 2-6)PFCONCOCNPFSTNSLTCNTo CO Connectionon CPU CardTo TelcoConnection4 PF XFER PCBYELBLU-WHTBLKWHT-BLUPFUCNAttached WireMetal SpacerREDNylon SpacerPFUCNGRN625ModularJackCPU82400-182CO/8STA PCBSingle LineTelephoneFigure 2-6 POWER FAILURE (4 PF XFER) PCBThe Power Failure (4 PF XFER) PCB provides DDK connectors for four power failure cut through circuits to four singleline telephones.To install a 4 PF XFER PCB:1. Place the two nylon spacers included with the 4 PF XFERPCB in the lower holes in the middle of the CPU (or2CO/8STA PCB, if installed).2. Align the 4 PF XFER PCB over the metal and nylon spacers.3. Using the two metal spacers included with the 4 PF XFERPCB, attach the PCB to the lower PCB.4. Refer to Part 4: Installing Optional Equipment for moreon installing Power Failure telephones.2-9
HDWR1B.QXD5/18/98 4:51 PMPage 10INSTALLING PCBsSMDR PCB (Figure 2-7)Set SW1 to the proper baud rate position byplacing the jumper over the pins of thedesired baud rate.SMDR Jack andCable AssemblySMDRNylon Spacer2 CO/8STA82400-17CPUFigure 2-7 SMDR PCBThe SMDR (Station Message Detail Recording) PCB provides a record of the system’s outside calls. Typically, therecord outputs to a customer-provided printer, terminal orSMDR data collection device. Use SMDR when you need tomonitor the usage at each extension and trunk.To install a SMDR PCB:1. Place the two nylon spacers included with the SMDR PCBin the upper holes in the middle of the CPU (or 2CO/8STAPCB, if installed).2. Align the SMDR PCB over the nylon spacers. Press thePCB into the connector labeled EXPCN on the CPU or2CO/8STA PCB.3. Connect the SMDR jack and cable assembly to the MainCabinet base. Insert the other end of the cable into theRSCN connector on the SMDR PCB.4. Using an RS-232C cable (Figure 2-8), plug the printer intothe SMDR jack assembly. Set the interface conditions ofthe printer as follows:Word length: 7 bitsParity bit: Even parityStop bit length: 2 bits2-10
HDWR1B.QXD5/18/98 4:51 PMPage 11INSTALLING PCBsSMDR RS-232C Cable Assembly (Figure 2-8)To connect the SMDR and printer, an RS-232C cable is required.If you make your own cable, it must be a straight-through cableconnecting pins 2, 3, 6, 7, 8 and 20. Refer to the Figure 2-8.Note that the cable length should not exceed 50’ in length.25 pin - 25 pin CableSMDR JackOutput Terminal25131425(female)Pin No.2367820RS-232C (25 pin)111482400 - 31RS-232C (25 pin)13(male)Pin No.2367820DescriptionReceive DataTransmit DataData Terminal ReadySignal GNDRequest To SendData Set ReadyDescriptionReceive DataTransmit DataData Terminal ReadySignal GNDRequest To SendData Set Ready25 pin - 9 pin CableSMDR JackOutput TerminalRS-232C (25 pin)1325(female)Pin No.2367820DescriptionReceive DataTransmit DataData Terminal ReadySignal GNDRequest To SendData Set ReadyRS-232C (9 pin)115146 9(male)Pin No.326514DescriptionTransmit DataReceive DataData Set ReadySignal GNDData Carrier DetectData Terminal Ready* The other Pins are not used. These Pin conditions are "Open".Figure 2-8 RS-232C CABLE ASSEMBLY2-11
HDWR1B.QXD5/18/98 4:51 PMPage 12POWERING UP THE SYSTEMPower-Up SequenceNow that all the PCBs you need are installed, you can powerup the system.1. Install a surge protector in the AC outlet you intend to usefor system power.2. Plug the AC power cord for the Main Cabinet into its surgeprotector.PCBCPU2-12System LEDs on Power-UpLEDStatusProcessor LED About 5 seconds after power-up,flashes quickly (red)
HDWR1C.QXD5/18/98 4:53 PMPage 13. INSTALLING EXTENSIONS AND TRUNKSSection 3Installing Extensions and TrunksIn this section . . .PageConnecting Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3Working With DDK Connectors . . . . . . . . . . . . . . . . . . .3-3Making Additional DDK Connectors . . . . . . . . . . . . . . .3-3Punching Down a DDK Installation Cable . . . . . . . . . . .3-4Connecting Extensions . . . . . . . . . . . . . . . . . . . . . . . .3-7Station Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7Connecting Trunks . . . . . . . . . . . . . . . . . . . . . . . . . .3-10Trunk Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-103-1
HDWR1C.QXD3-25/18/98 4:53 PMPage 2
HDWR1C.QXD5/18/98 4:53 PMPage 3CONNECTING BLOCKSWorking With DDK ConnectorsThe system uses DDK-type connectors for extensions, trunks andoptional equipment. Using the optional DDK Installation Cables (4pin station cable P/N 82490, 2-pin power failure cable 82491, and2-pin C.O. line cable 82492) makes it easy to connect the PCBs tostandard 66M1-50 connecting blocks. The cables available for thesystem are for CO lines (one-pair), keysets (2-pair), and PowerFailure Jumpers/auxiliary options (one-pair). If desired, separateDDK connectors without cable can be purchased. In general, eachcabinet needs: Two 66M1-50 block and DDK Installation Cable for extensions. One 66M1-50 block and DDK Installation Cable for optionalequipment One to eight (depending on your requirements) RJ11C modularjacks and one DDK Installation Cable for trunks.Making Additional DDK Connectors (Figure 3-1)To make DDK connectors, using 22 or 24 gauge solid 2-pair twistedwire for keysets or 22 or 24 gauge solid 1-pair twisted wire for COlines, single line telephones, Power Failure Jumpers, or auxiliaryfunctions, do the following:1. Do not strip the wires. Insert the wires into the top piece (clearplastic) of the connector. Following the standard color code:#1 White/Blue, #2 Blue/White,#3 White/Orange, #4 Orange/White(Ignore #3 and #4 if only using 1-pair twisted wire)Refer to Figure 3-4 for additional help with the color code. Makesure that the wire ends do not protrude beyond the back of theconnector.2. Place the top half of the connector over the lower half and pressdown or use pliers to snap together. Verify that the connectorwill not come apart and that all the wires are secure. Oncetogether, these connectors will not separate without breaking.3-3
HDWR1C.QXD5/18/98 4:53 PMPage 4CONNECTING BLOCKSWHT/BLUUpper HalfBLU/WHTWHT/ORNORN/WHT1 (T)2 (R)3 (H)4 (L)Approx. 5/16"Two pair twistedtelephone wireDDK Connector82400- 30Lower HalfFigure 3-1 MAKING DDK CONNECTORSPunching Down a DDK Installation CableThe DDK Installation Cables have 4-pin DDK connectors installedon one end and are unterminated on the other.1. For each 66M1-50 block, punch down the DDK InstallationCable in standard color-code order.Refer to Figure 3-3 if you need help with the color code.2. After you have punched down your cables, route them throughthe bottom of the cabinet and secure them with the strain reliefbar (Figure 3-2).3-4
5/18/98 4:53 PMPage 5CONNECTING BLOCKS82400 - 29HDWR1C.QXDFigure 3-2 SECURING THE CABLES3-5
HDWR1C.QXD5/18/98 4:53 PMPage 6CONNECTING BLOCKSNo Connection- Only CPU- With twoexpansion PCB’s- With oneexpansion PCBT TipR RingH HighL LowFigure 3-3 CONNECTING BLOCK3-6
HDWR1C.QXD5/18/98 4:53 PMPage 7CONNECTING EXTENSIONSStation Connections (Figure 3-4)The CPU has 4-pin DDK connectors for eight stations. EachExpansion (2CO/8STA) PCB provides for an additional eight stations. Two Expansion PCB’s are allowed per system providing atotal of twenty-four stations per system.Refer to Part 4: Installing Optional Equipment for instructions on connecting a power failure telephone.2CO/8STA PCB10/1811/1912/2013/2114/2215/2382400 - EL7TEL8Figure 3-4 STATION CONNECTIONS1. Following the conventional color code, insert the DDK connectors into the PCB. For example, the first eight stations in the system would have these connections:Ext./PortDDK Connector Pair1011121314151617WHT-BLU / BLU-WHT / WHT-ORN / ORN-WHTWHT-GRN / GRN-WHT / WHT-BRN / BRN WHTWHT-SLT / SLT-WHT / RED-BLU / BLU-REDRED-ORN / ORN-RED / RED-GRN / GRN-REDRED-BRN / BRN-RED / RED-SLT / SLT-REDBLK-BLU / BLU-BLK / BLK-ORN / ORN-BLKBLK-GRN / GRN-BLK / BLK-BRN / BRN-BLKBLK-SLT / SLT-BLK / YEL-BLU / BLU-YELNote that single line telephones only use one-pair wire(T/R). When installing a single line set, the second pair isnot used (H/L).2. Install a modular jack for each extension within six feet of thetelephone’s location. See Figure 3-5.3-7
HDWR1C.QXD5/18/98 4:53 PMPage 8CONNECTING EXTENSIONS3. For each keyset, run two-pair 24 AWG station cable from thecross-connect block to the modular jack. For each single linephone, run one-pair 24 AWG station cable from the cross-connect block to the modular jack.4. Terminate the station cable to the module jack lugs:WHT-BLU to GREEN lugBLU-WHT to RED lugWHT-ORN to BLACK lug *ORN-WHT to YELLOW lug ** Lug not used when installing a single line phone.5. Back at the MDF, run two pairs of cross-connect wires (or onepair of cross-connect wires for single line phones) between thepins on the B block and cross-connect block to complete theconnection.6. Install bridging clips as required.7. After completing step 6, you should be able to place and answercalls at the extension.Two PairCross EDWHT-ORNBLKWHT-BLUGRNFigure 3-5 CONNECTING KEYSET TELEPHONES3-804082DDK Installation Cable-5625ModularJack
HDWR1C.QXD5/18/98 4:53 PMPage 9CONNECTING EXTENSIONSOne-Pair Cross-Connect82400 - 48YELBLU-WHTRED"B" ModularJack25-Pair DDKInstallation CableSingle LineTelephoneFigure 3-6 CONNECTING SINGLE LINE TELEPHONES3-9
HDWR1C.QXD5/18/98 4:53 PMPage 10CONNECTING TRUNKSTrunk Connections (Figure 3-7)The CPU has 2-pin DDK connectors for four loop start CO trunks.Each Expansion (2CO/8STA) PCB provides an additional two COtrunk connections. Two Expansion PCB’s are allowed per systemproviding a total of eight trunks per system.Refer to Part 4: Installing Optional Equipment for instructions on connecting a power failure telephone.CPU2CO/8STA PCBCOCNCOCNCO5/7 CO6/8CO1CO2CO3CO482400 - 2682400 - 24CO/PBX Line 4CO/PBX Line 3CO/PBX Line 2CO/PBX Line 6 or 8CO/PBX Line 1CO/PBX Line 5 or 7Figure 3-7 TRUNK CONNECTIONS1. Following the conventional color code, insert the DDK connectors into the PCB. For example, the CPU would have these connections:TrunkDDK Connector Pair1234WHT-BLU / BLU-WHTWHT-ORN / ORN-WHTWHT-GRN / GRN-WHTWHT-BRN / BRN WHT2. For each trunk, run one pair of wires from the DDK connectionto a 625 modular jack, which then connects to the telco’s RJ11Cjacks using a standard line cord (Figure 3-8 on the followingpage).3. After completing step 2, you should be able to place and answercalls over the connected trunk.3-10
HDWR1C.QXD5/18/98 4:53 PMPage 11CONNECTING TRUNKS625ModularJack GRNTelcoRJ11CWHT-BLUREDBLU-WHT82400 - 12LineCordTo Central OfficeTo CO connectoron CPU or2CO/8STA PCBDDKConnector25-Pair DDKInstallation CableFigure 3-8 CONNECTING TRUNKS3-11
HDWR1C.QXD3-125/18/98 4:53 PMPage 12
HDWR1D.QXD5/18/98 4:55 PMPage 14. INSTALLING OPTIONAL EQUIPMENTSection 4Installing Optional EquipmentIn this section . . .PageAlarm Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3Using External Alarm Sensors . . . . . . . . . . . . . . . . . . . . . .4-3Installing an External Alarm Sensor Circuit . . . . . . . . . . . .4-3Caller ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5Using Caller ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5Installing Caller ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5DSS Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8Using a Direct Station Selection Console . . . . . . . . . . . . . .4-8Installing a DSS Console . . . . . . . . . . . . . . . . . . . . . . . . . .4-8External Paging and Page Relays . . . . . . . . . . . . . . . . .4-9Using External Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-9Installing External Paging and Page Relays . . . . . . . . . . . .4-9Door Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-12Using the Door Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-12Installing a Door Box . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-12Installing Door Strike Control Relays . . . . . . . . . . . . . . . .4-14Music Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-16Music on Hold and Background Music . . . . . . . . . . . . . .4-16Installing a Music Source on an Auxiliary PCB . . . . . . . .4-16Power Failure Telephones . . . . . . . . . . . . . . . . . . . . . .4-18Power Failure Cut-Through . . . . . . . . . . . . . . . . . . . . . . .4-18Installing a Power Failure Telephone . . . . . . . . . . . . . . . .4-18Voice Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-20Using Voice Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-20Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-21Wall-Mount Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-23Using the Wall-Mount Kit . . . . . . . . . . . . . . . . . . . . . . . . .4-23Installing the Wall-Mount Handset Hanger . . . . . . . . . . .4-23Wall-Mounting a Key Telephone . . . . . . . . . . . . . . . . . . .4-244-1
HDWR1D.QXD4-25/18/98 4:55 PMPage 2
HDWR1D.QXD5/18/98 4:55 PMPage 3ALARM SENSORSUsing External Alarm SensorsThe Auxiliary PCB provides two alarm circuits which detect a make(open) or break (closed) contact from an alarm. Programming determines if the alarm inputs require an open or closed circuit.An alarm detection causes the system to send a signal to stations programmed to receive the alarms. The alarm signal can also be sent toexternal paging speakers.Note: The Auxiliary PCB alarm feature can use a 10-30 VDC powersupply installed in series with the alarm circuit.Installing an External Alarm Circuit (Figure 4-1)CAUTIONBe sure the requirements of the alarm system sensors do not exceedthe system specifications.With Internal Power: loop resistance of less than 100 OhmsWith External DC Power: 5 to 24 VDC with 0.65 mA to 4.5 mANote: External powered alarm sensors are polarity sensitive(see Figure 4-2). Additionally, the external power shouldprovide current limiting.1. Locate an available 2-pin DDK connector in an auxiliary (C)block.2. For the DDK connector chosen, cross-connect the associated wirepair from the C block to the cross-connect block.3. Install bridging clips as required.4. Connect the two leads from the first external alarm to the associated terminals on the cross-connect block.5. Plug the DDK connector into the ALM1 connector on theAuxiliary PCB.6. Repeat steps 1-4 for the second external alarm, if required.7. Plug the DDK connector into the ALM2 connector on theAuxiliary PCB.Note: When using internal power to connect the dry contact of analarm-detecting device to the system, set the SW3 switch (Alarm1) and SW4 switch (Alarm 2) on the Auxiliary PCB to INPOW.4-3
HDWR1D.QXD5/18/98 4:55 PMPage 4ALARM SENSORSOne-Pair Cross-ConnectInput fromalarmsystemTo alarm inputon Auxiliary PCB82400 - 11"C" BlockDDKConnectorCrossConnectBlock25-Pair DDKInstallation CableFigure 4-1 CONNECTING AN ALARMAlarm Input 2Alarm Input 11 21 2CN1RL2CN2RL1 ALM2 ALM1SW4CTR2 SPK2 CTR1 SPK1SW3EXPOW INPOW EXPOW INPOWAuxiliary PCBSW4SW382400 - 40EXPOW INPOW EXPOW INPOW(ALM2)(ALM1)Using internalpowerFigure 4-2 CONNECTING TO THE AUXILIARY PCB4-4
HDWR1D.QXD5/18/98 4:55 PMPage 5CALLER IDUsing Caller IDCaller ID allows a display keyset to show an incoming caller’s telephone number and/or name with the time and date on the phones display. The caller’s information can be checked before answering anincoming call. The information received by the system depends uponthe capabilities of your local telco.The system requires the following:System Software 2.1B or higherCaller ID/SMDR PCB (P/N 82421)This PCB is used in place of the SMDR PCB (P/N 82420) andprovides both Caller ID and SMDR capability. Caller ID Adaptor (P/N 82425)The Caller ID Adaptor provides 8 detection circuits for CallerID data. Installation (Figure 4-3)RUN1 21 2INT RST1. Locate a clean, dry spot that is out of direct sunlight and near thePortrait KSU. The Caller ID Adaptor must be installed within 2’ ofthe lower right side of the KSU (determined by the length of theinterconnecting cable). The area should be well ventilated and thetemperature should remain at a normal level.2. Remove the cover from the Caller ID Adaptor.3. Tack-fasten two of the four wood screws (provided) on the wall atabout 8 11/16” apart. For easier installation, you can use the baseas a mounting template.4. Place the Caller ID Adaptor over the tacked screws. Fully tightenthe screws and install the remaining two wood screws.5. Remove the cover from the KSU by unscrewing the two captivescrews on the lower half of the cabinet cover. Lift up the lowerhalf of the cover -- then slide it back slightly to remove it.6. Before proceeding further, make sure switches1 & 2 of the CPU Mode Switch are set to theRUN position and the battery is installed inthe system. This is necessary in order toretain the current system programming.7. Unplug the AC power cord for the KSU from its surge protector.4-5
HDWR1D.QXD5/18/98 4:55 PMPage 6CALLER ID8. Set the jumpers on the Caller ID/SMDR PCB. Set jumper-SW1 tomatch the baud rate of the SMDR Unit. Set jumper-SW2 to the“RUN” position, this setting allows the system to use the customer’s current programming.9. Place the two nylon spacers included with the Caller ID/SMDRPCB in the upper holes in the middle of the CPU (or 2CO/8STAPCB, if installed).10. Align the Caller ID/SMDR PCB over the nylon spacers. Press thePCB into the connector labeled EXPCN on the CPU or 2CO/8STAPCB. The PCB should then be snapped on to the spacers.11. Connect the Caller ID cable to the CBCN connector and G terminal on the Caller ID/SMDR PCB. Connect the opposite end to theSMDCN connector and G terminal on the Caller ID Adaptor.12. Mount the SMDR jack (RS-232 connector) to the base of theKSU. Connect the opposite end of the cable to the RSCN connector on the Caller ID/SMDR PCB.13. Connect the FG ground on the KSU to the ETH ground connectoron the Caller ID Adaptor using the green wire with spade lug endsprovided.14. With DDK connectors attached to both ends, connect a one-pairjumper from the TRCN connector on the Caller ID Adaptor to thecorresponding COCN connector on either the CPU or Expansion(2CO/8STA) PCB. Repeat this step for additional CO lines.15. For each CO trunk, run one pair of wires with DDK connectors onone end from the COCN connector on the Caller ID Adaptor to a625 modular jack. The jack is then connected to telco’s RJ11Cjack using a standard line cord.16. Replace the front cover on the KSU, and the front cover on theCaller ID Adaptor.17. Plug the AC power cord for the KSU into its surge protector.18. Refer to the Portrait Pocket Guide (P/N 824000PKT**) forrequired programming.4-6
5/18/98 4:55 PMPage 7CALLER IDSet SW1 to the properbaud rate position placingthe jumper over the pinsof the desired baud rate.TESTRUNSW2Portrait KSUSMDR Jack andCable AssemblyCaller ID/SMDR PCBGCBCNNylonSpacer2 CO/8 ckSMDCNCOTR8TR
years - depending on how often the system is powered down. The more the system's power is off, the shorter the battery's life. Connection points for the CO and station DDK connectors. 82400 - 36 Station 1 Trunk 4 Battery Trunk 3 Trunk 2 Trunk 1 Station 2 Station 3 Station 4 Station 5 Station 6 Station 7 Station 8 HDWR1B.QXD 5/18/98 4:51 PM .
- HARDWARE USER MANUAL - MANUEL DE L'UTILISATEUR HARDWARE . - HARDWAREHANDLEIDING - MANUALE D'USO HARDWARE - MANUAL DEL USUARIO DEL HARDWARE - MANUAL DO UTILIZADOR DO HARDWARE . - 取扱説明書 - 硬件用户手册. 1/18 Compatible: PC Hardware User Manual . 2/18 U.S. Air Force A -10C attack aircraft HOTAS (**) (Hands On Throttle And .
*ACS880-01 drives hardware manual 3AUA0000078093 *ACS880-04 drive modules (200 to 710 kW, 300 to 700 hp) hardware manual 3AUA0000128301 ACS880-04 single drive module packages hardware manual 3AUA0000138495 *ACS880-07 drives (45 to 630 kW, 50 to 700 hp) hardware manual 3AUA0000105718 *ACS880-07 drives (560 to 2800 kW) hardware manual 3AUA0000143261
ACS800-01/U1 Hardware Manual 3AFE64382101 ACS800-04/04M/U4 Hardware Manual (45 to 560 kW) 3AFE64671006 ACS800-04 Drive Modules Hardware Manual (0.55 to 200 kW) 3AFE68372984 ACS800-11/U11 Hardware Manual 3AFE68367883 ACS800-14 Frequency Converter Modules Supplement 3AFE68458986 ACS800-31/U31 Hardware Manual 3AFE64671006
HARDWARE MANUALS (appropriate manual is included in the delivery) ACS800-01/U1 Hardware Manual 0.55 to 110 kW (0.75 to 150 HP) 3AFE64382101 (English) ACS800-01/U1 Marine Supplement 3AFE64291275 (English) ACS800-02/U2 Hardware Manual 90 to 500 kW (125 to 600 HP) 3AFE64567373 (English) ACS800-11/U11 Hardware Manual 5.5 to110 kW (7.5 to 125 HP)
HARDWARE MANUAL This manual describes the part names, dimensions, mounting, cabling and specifications for the product. This manual is extracted from FX 3U Series User's Manual - Hardware Edition. Refer to FX Series User's Manual - Hardware Edition for more details. Before use, read this manual and manuals of relevant products fully to
complete hardware-related details about one specific Apollo model. Included are detailed descriptions of all hardware features, controls, connectors, and specifications. Note: Each hardware manual contains the unique Apollo model in the file name. Apollo Software Manual The Apollo Software Manual is the companion guide to the Apollo hardware .
3. Mounting Hardware: a. Use mounting hardware that came with the TV, or b. If the TV did not come with mounting hardware, select from included Bolts and Washers (see Parts List on page 7). WARNING! To prevent serious injury, do not use hardware that does not match the TV's hardware, that is too long or too short, or overtighten the hardware.
IT hardware, and only 17 percent actually inventory all IT hardware. On average, about 76 percent of an organiza-tion's IT hardware is inventoried. Any IT hardware that's not inventoried is either intentional (by design) or the result of poorly enforced policies. The scope of IT hardware encompasses a wide range
