Issue Missoula County Public Schools Date: Date
GENERAL MISSOULA COUNTY PUBLIC SCHOOLS LEGEND NOTE: THESE ARE STANDARDIZED SYMBOLS LEGENDS. AS SUCH, ALL SYMBOLS SHOWN MAY NOT APPEAR ON OR WITHIN THIS SET OF CONTRACT DOCUMENTS. SYMBOL NAME X SPECIFIC SHEET NOTE P-X PLUMBING FIXTURE IDENTIFICATION X XX EQUIPMENT MARK "X" INDICATES TYPE "XX" INDICATES NUMBER X-X XXX SYMBOL X XX ISSUE ISSUE DATE: DATE REVISIONS DATE DESCRIPTION Hellgate High School Welding Shop Dust Collection System NAME SECTION REFERENCE NUMBER SECTION REFERENCE SHEET 925 Gerald Ave., Missoula, MT 59801 ON DEMOLITION PLANS: INDICATES ITEMS TO BE REMOVED JM ENGINEERING No. 22002 POINT OF NEW CONNECTION G-R-D IDENTIFICATION CFM AIR FLOW Project Manager JM TA MON NA GISTERED RE John Hugh Melvin No. 10903PE MECHANICAL AND PLUMBING LEGEND 12"ø ROUND DUCT 12"/6" OVAL DUCT (VIEW WIDTH x VIEW DEPTH) ACOUSTICALLY LINED DUCT EXTERIOR INSULATED DUCT EXTERIOR INSULATED AND ACOUSTICALLY LINED DUCT HWS HEATING WATER SUPPLY HWR HEATING WATER RETURN CWS CHILLED WATER SUPPLY CWR CHILLED WATER RETURN CTWS COOLING TOWER WATER SUPPLY CTWR COOLING TOWER WATER RETURN HPSS HEAT PUMP SOURCE SUPPLY HPSR HEAT PUMP SOURCE RETURN HPLS HEAT PUMP LOAD SUPPLY HPLR HEAT PUMP LOAD RETURN HSP HIGH PRESSURE STEAM HSC HIGH PRESSURE STEAM CONDENSATE MPS MEDIUM PRESSURE STEAM MPC MEDIUM PRESSURE STEAM CONDENSATE FLEXIBLE ROUND DUCT LPS LOW PRESSURE STEAM VERTICAL SUPPLY AIR OR POSITIVE PRESSURE DUCTS VERTICAL RETURN AIR OR NEGATIVE PRESSURE DUCTS LPC LOW PRESSURE STEAM CONDENSATE RS REFRIGERANT SUCTION RL REFRIGERANT LIQUID VERTICAL EXHAUST AIR DUCTS MANUAL BALANCING / VOLUME DAMPER COND CONDENSATE NG NATURAL GAS LPG LIQUEFIED PETROLEUM GAS (PROPANE) MOTOR ACTUATED DAMPER F DUCT MOUNTED VERTICAL FIRE DAMPER V VENT - SANITARY SAN SANITARY WASTE - ABOVE GRADE SAN SANITARY WASTE - BELOW GRADE RDL ROOF DRAIN LEADER RDO ROOF DRAIN OVERFLOW PIPE UP GLOBE VALVE F/S PLUG VALVE BUTTERFLY VALVE CHECK VALVE CONICAL TAKE-OFF HIGH EFFICIENCY TAKE-OFF (HETO) MITERED RECTANGULAR DUCT ELBOW WITH TURNING VANES CIRCUIT SETTER COMBINATION AUTO BALANCE AND SHUT-OFF WITH TEST PORTS AND UNION STRAINER COMBINATION STRAINER AND SHUT-OFF WITH TEST PORTS AND UNION 1.0 RADIUS AND 1.5 RADIUS SMOOTH ROUND OR OVAL ELBOW BACKFLOW PREVENTER 1.0 RADIUS AND 1.5 RADIUS 3-GORE ROUND OR OVAL ELBOW PRESSURE REDUCING / REGULATING VALVE MOTORIZED CONTROL VALVE TEMPERATURE CONTROLS SOLENOID VALVE PRESSURE GAUGE THERMOMETER SYMBOL RTU-1 T DESCRIPTION PRESSURE RELIEF VALVE THERMOSTAT - LABEL INDICATES ASSOCIATED SYSTEM RZ-1 S SENSOR - LABEL INDICATES ASSOCIATED SYSTEM H FLEXIBLE PIPE CONNECTOR 3-WAY VALVE STEAM TRAP FC-1 HUMIDISTAT - LABEL INDICATES ASSOCIATED SYSTEM PUMP / CIRCULATOR AHU-1 CO² CARBON DIOXIDE SENSOR - LABEL INDICATES ASSOCIATED SYSTEM HOSE BIBB ROUND FLOOR DRAIN P PRESSURE SENSOR DP DIFFERENTIAL PRESSURE SENSOR SQUARE FLOOR DRAIN SQUARE FLOOR DRAIN 4/7/2022 2:15:33 PM WALL CLEANOUT (WCO) FS FLOW SWITCH CS CURRENT SENSOR IMPORTANT: PROVIDE COMBINATION SMOKE/FIRE/CO DETECTOR IN ALL SLEEPING AREAS. COORDINATE WITH ARCHITECTURAL & ELECTRICAL SUBMITTALS SHALL BE IN PDF FORMAT ONLY. PARTIAL OR INCOMPLETE SUBMITTALS AND PAPER COPIES WILL NOT BE REVIEWED. SUBMITTALS SHALL BE COMBINED INTO ONE FILE, WITH EACH SECTION LABELED ACCORDING TO IT'S RESPECTIVE SPECIFICATION SECTION. BALANCING VALVE / CIRCUIT SETTER SHARP-THROAT RADIUS-HEEL RECTANGULAR DUCT ELBOW 1.0 RADIUS AND 1.5 RADIUS 5-GORE ROUND OR OVAL ELBOW REFER TO SPECIFICATIONS FOR ALL MECHANICAL AND PLUMBING RELATED WORK. ALL WORK SHALL BE IN STRICT ACCORDANCE WITH THE PLANS, SPECIFICATIONS, AND MANUFACTURERS WRITTEN INSTRUCTIONS. ALL DEVIATIONS FROM THE PLANS AND/OR SPECIFICATIONS SHALL REQUIRE WRITTEN PRIOR APPROVAL FROM THE ENGINEER. BALL VALVE GATE VALVE STRAIGHT TAKE-OFF N EE R DOMESTIC HOT CIRCULATION (DHC) PIPE REDUCER / INCREASER DUCT MOUNTED HORIZONTAL FIRE OR FIRE / SMOKE DAMPER 2015 JM ENGINEERING, PLLC DOMESTIC HOT WATER (DHW) PIPE DOWN DUCT MOUNTED VERTICAL FIRE / SMOKE DAMPER C DOMESTIC COLD WATER (DCW) PARALLEL BLADE DAMPER OPPOSED BLADE DUCT THIS DRAWING IS THE PROPERTY OF THE ENGINEER. IT HAS BEEN PREPARED SPECIFICALLY FOR THIS SITE AND IS NOT TO BE USED FOR ANY OTHER PURPOSE, LOCATION, OR OWNER APPLICATION WITHOUT WRITTEN CONSENT OF THE ENGINEER. FLOOR CLEANOUT (FCO) CLEANOUT-TO-GRADE (COTG) NOTE: THESE ARE STANDARDIZED SYMBOLS LEGENDS. AS SUCH, ALL SYMBOLS SHOWN MAY NOT APPEAR ON OR WITHIN THIS SET OF CONTRACT DOCUMENTS. DRAWING INDEX ABBREVIATIONS (E) (IJS) or I.J.S. (N) (NL) (REL) A.D. A.F.F. A.F.G. AHU ARCH CA CC CFM CH CHWR or CWR CHWS or CWS CO or C.O. CONT. COTG CUH DCW DHW DHC DF EA EC EF FA FC FD FE FEC FF or FIN.FLR. FS FT G.C. HB HC EXISTING IN JOIST SPACE NEW NEW LOCATION RELOCATE or RELOCATED ACCESS DOOR ABOVE FINISH FLOOR ABOVE FINISH GRADE AIR HANDLING UNIT ARCHITECT or ARCHITECTURAL COMPRESSED AIR COOLING COIL CUBIC FEET PER MINUTE CABINET HEATER CHILLED WATER RETURN CHILLED WATER SUPPLY CLEANOUT CONTINUATION CLEANOUT TO GRADE CABINET UNIT HEATER DOMESTIC COLD WATER DOMESTIC HOT WATER DOMESTIC HOT WATER RECIRCULATION DRINKING FOUNTAIN EXHAUST AIR ELECTRICAL CONTRACTOR EXHAUST FAN FRESH AIR FAN COIL FLOOR DRAIN FIRE EXTINGUISHER FIRE EXTINGUISHER CABINET FINISH FLOOR FLOOR SINK FIN TUBE GENERAL CONTRACTOR HOSE BIBB HEATING COIL HHW HWR HWS LAV LCUV MA MAX. MC MECH. MFR. MIN. N.C. N.O. O.C. OA PG PICV RA RDL RDO REQ'D RHC S.M. S.S. SA SAN SIM. SPEC. TA TYP. U.N.O. UH UR UV VFD V VTR WC WS or WF HEATING HOT WATER HEATING WATER RETURN HEATING WATER SUPPLY LAVATORY LARGE CAPACITY UNIT VENTILATOR MIXED AIR MAXIMUM MECHANICAL CONTRACTOR MECHANICAL MANUFACTURER MINIMUM NORMALLY CLOSED NORMALLY OPEN ON CENTER OUTSIDE AIR PROPYLENE GLYCOL PRESSURE INDEPENDENT CONTROL VALVE RETURN AIR ROOF DRAIN LEADER ROOF DRAIN OVERFLOW REQUIRED REHEAT COIL SHEET METAL STAINLESS STEEL SUPPLY AIR SANITARY SEWER SIMILAR SPECIFICATION or SPECIFIED TRANSFER AIR TYPICAL UNLESS NOTED OTHERWISE UNIT HEATER URINAL UNIT VENTILATOR VARIABLE FREQUENCY DRIVE VENT VENT THROUGH ROOF WATER CLOSET WASH SINK/FOUNTAIN (LAVATORY) COVER SHEET / GENERAL MP01 COVER SHEET MECHANICAL DM101 M101 M701 M801 DEMOLITION MECHANICAL PLAN MAIN LEVEL MECHANICAL ELECTRICAL STRUCTURAL PLAN MECHANICAL STRUCTURAL SECTIONS AND ISOMETRICS MECHANICAL STRUCTURAL SCHEDULES AND DETAILS PROJECT NO: DRAWN BY: CHECKED BY: 22002 Author JM COVER SHEET MP01 Project Status 12"x6" RECTANGULAR DUCT (VIEW WIDTH x VIEW DEPTH) DESCRIPTION 925 Gerald Ave., Missoula, MT 59801 NOTE: DUCT DIMENSIONS INDICATE CLEAR INSIDE DIMENSIONS. EXTERIOR INSULATION OR ACOUSTICAL LINER THICKNESS IS NOT INCLUDED IN DIMENSIONS INDICATED. SYMBOL 2300 Regent Street, Suite 207 Missoula, MT 59801 406.542.2849 www.jmengineering.net DESCRIPTION ES GI SIO NAL EN Hellgate High School Welding Shop Dust Collection System SYMBOL OF PR PIPING / PLUMBING - WETSIDE DUCTWORK - DRYSIDE
ISSUE ISSUE DATE: DATE REVISIONS X 1 2 3 4 5 6 7 8 9 10 11 12 13 GENERAL DEMOLITION NOTES SPECIFIC SHEET NOTES A. B. REMOVE EXISTING ROUGHING SCREEN (RS) COMPLETE. REMOVE EXISTING WELDING EXHAUST ARMS AND DROPS COMPLETE. REMOVE EXISTING MAKEUP AIR UNIT COMPLETE INCLUDING ALL FILTER AND DAMPER SECTIONS UPSTREAM OF UNIT. DISCONNECT ELECTRICAL AND REMOVE ALL WIRING BACK TO PANEL. DISCONNECT GAS INPUT AND CAP AT GAS LINE AT MAIN. REMOVE EXISTING FOUNDRY HOOD COMPLETE. EXISTING GRILLE TO REMAIN. REMOVE ALL EXISTING DUCTWORK COMPLETE INCLUDING ALL FITINGS, HANGERS, AND SUPPORTS. REMOVE DUCT BACK TO FURTHEST POINT. CAP EXHAUST DUCT AT RISER. ABANDON EXISTING EXHAUST FAN (EF-3) IN MECHANICAL PENTHOUSE IN PLACE AND DISCONNECT FROM POWER. DISCONNECT AND RELOCATE EXISTING EXHAUST FAN (LOREN COOK 180SQN-HP). SEE NEW DRAWINGS FOR NEW LOCATION. REMOVE EXISTING SUPPLY DIFFUSER. EXISTING OUTSIDE AIR RISER TO REMAIN. PATCH DUCT FROM ORIGINAL MAKE UP AIR UNIT AND PREPARE FOR CONNECTION TO NEW MAKE UP AIR SYSTEM. CUT (E) ASPHALT FOR NEW DUST COLLECTOR SLAB. PREP SITE AS NECESSARY AND PATCH BACK AS NECESSARY. SEE DETAIL 3/M701. COORDINATE DUCT REMOVAL WITH (E) LIGHTING. REPLACE LIGHTING WHEN REMOVAL IS REQUIRED TO REMOVE DUCTING. DATE SPECIFIC NOTES AND HEAVY DASHED LINES INDICATE ITEMS TO BE REMOVED. WHEN DUCTWORK, HYDRONIC PIPING, PLUMBING, EQUIPMENT, ETC. IS REMOVED, DEMOLITION SHALL ALSO INCLUDE COMPLETE REMOVAL OF ALL RELATED HANGERS, SUPPORTS, STRAPS, CONTROLS, AND CONTROL WIRING OR TUBING. EXCEPTIONS ARE ITEMS THAT WILL BE REUSED OR OTHERWISE NOTED. THE CONTRACTOR IS RESPONSIBLE FOR FIELD VERIFYING ALL UTILITIES, PIPING SYSTEMS, POWER SYSTEMS, COMMUNICATION SYSTEMS, ETC. REGARDLESS OF ABOVE OR BELOW GRADE THAT MAY BE AFFECTED BEFORE WORK BEGINS. ALL PATCHING, REPAIRING, PAINTING OF WALLS DUE TO UNIT OR ITEM DEMOLITION ONLY WILL BE PROVIDED BY THE GENERAL CONTRACTOR. ANY DAMAGE TO EXISTING UTILITIES, FACILITIES, LANDSCAPING, ETC. SHALL BE REPAIRED OR REPLACED (OWNER'S CHOICE) AT THE CONTRACTOR'S EXPENSE. PIPING AND DUCTWORK INDICATED IS PARTIALLY DIAGRAMMATIC. CONTRACTOR SHALL DETERMINE IN FIELD EXACT LOCATION OF ALL DUCTWORK, PIPING AND EQUIPMENT. CONTRACTOR SHALL COORDINATE WITH ALL OTHER TRADES PRIOR TO INSTALLATION OF EQUIPMENT. UPON COMPLETION OF WORK THE CONTRACTOR SHALL CLEAN ALL DEBRIS FROM THE WORK AREA AND OTHER AREAS USED BY THE CONTRACTOR, AND LEAVE PREMISES IN A NEAT AND CLEAN CONDITION. CLEAN, PATCH AND REPAIR ALL WALLS, FLOORS, CEILINGS, AND OTHER SURFACES DAMAGED OR MARKED DURING CONSTRUCTION. ALL WORK SHALL COMPLY WITH THE MOST STRINGENT OF APPLICABLE CODES, ORDINANCES, AND REQUIREMENTS BY THE ENGINEER. ALL DISTURBED FIREPROOFING ON STRUCTURAL BEAMS FROM EQUIPMENT AND DUCT REMOVAL SHALL BE PATCHED BACK, MAKING CONTINUOUS. C. D. E. F. G. H. I. DESCRIPTION TA MON NA GISTERED RE John Hugh Melvin No. 10903PE N EE R OF PR 12 ES GI SIO NAL EN THIS DRAWING IS THE PROPERTY OF THE ENGINEER. IT HAS BEEN PREPARED SPECIFICALLY FOR THIS SITE AND IS NOT TO BE USED FOR ANY OTHER PURPOSE, LOCATION, OR OWNER APPLICATION WITHOUT WRITTEN CONSENT OF THE ENGINEER. C 5 2015 JM ENGINEERING, PLLC 2 2 2 2 1 6 13 1 6 13 9 2300 Regent Street, Suite 207 Missoula, MT 59801 406.542.2849 www.jmengineering.net 6 2 6 2 2 2 2 6 6 3 13 3 6 11 10 6 6 4 5 2 PROJECT NO: DRAWN BY: 8 CHECKED BY: 925 Gerald Ave., Missoula, MT 59801 7 Hellgate High School Welding Shop Dust Collection System 2 22002 Author Checker TO BURN TABLE ACROSS HALL 1 NORTH 1ST FLOOR MECHANICAL DEMOLITION PLAN SCALE: 1/4" 1'-0" DM101 Project Status 4/7/2022 2:15:26 PM DEMOLITION MECHANICAL PLAN
1. 3 M701 2. DC 1 3. 4. 1"ø CA 16 6. 16 26"ø RA 15 16 1 A. RELOCATED EXISTING EXHAUST FAN (LOREN COOK 180SQN-HP). ADJUST SPEED CONTROLLER AND CHANGE MOTOR PULLEY TO 400 CFM FROM BURN TABLE. PROVIDE BACKDRAFT DAMPER DOWNSTREAM OF FAN BEFORE TRUNK CONNECTION. ELECTRICAL CONTRACTOR TO RECONNECT TO SAME CIRCUIT. PRICE INDUSTRIES 300 HEAVY DUTY AIRFOIL SUPPLY GRILLE, SIZE 18"x16". SET BLADES AT 15 DEGREES DOWN TOWARDS SPACE. NEW 3'-6" ROUND HOOD FOR FOUNDRY. CONSTRUCT OF HEAVY GAUGE SHEET METAL. CENTER OVER FOUNDRY AND COORDIANTE EXACT LOCATION WITH WELDING INSTRUCTOR. 5' TELESCOPIC EXHAUST ARM ATTACHED TO DUST COLLECTOR DROP. KEMPER MODEL 91 315. 7' TELESCOPIC EXHAUST ARM WITH MOUNTING COLUMN ATTACHED TO DUST COLLECTOR DROP. KEMPER MODEL 91 320. CONNECT NEW MAKE UP AIR UNIT TO 2-1/2" EXSISTING GAS MAIN NEAR THIS LOCATION. 26" SPARK ARRESTOR. IMPERIAL SYSTEMS SPARK TRAP. COORDINATE EXISTING COMPRESSED AIR INFRASTRUCTURE WITH WELDING SHOP INSTRUCTOR. (E) VERTICAL CONTROL JOINT THIS LOCATION. MAINTAIN 1'-6" MIN FROM JOINT FOR NEW DUCT PENETRATIONS (AS SHOWN). LINTEL IN (E) EXT. WALL. SEE DETAIL 1/M801. LINTEL IN (E) INT. NON-LOAD BEARING WALL. SEE DETAIL 1/M801. COORDINATE DUCT INSTALLATION WITH EXISTING LIGHTING. DUCT TO ROUTE ABOVE EXISTING LIGHTING WHERE POSSIBLE TO MAINTAIN LIGHTING IN BOOTHS. COMPRESSED AIR REFRIGERATED DRYER (SEE AIR COMPRESSOR SCHEDULE) AND CONDENSATE PUMP. ROUTE COMPRESSED AIR CONDENSATE FROM DRYER TO SINK THIS LOCATION. EXTERIOR RECTANGULAR DUCT TO BE CROSS BROKEN ON TOP FOR RUN OFF. APPLY UV PAINT ON ALL EXTERIOR DUCTS. 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 THE CONTRACTOR IS RESPONSIBLE FOR FIELD VERIFYING ALL UTILITIES, PIPING, UNDERGROUND WIRING, TELEPHONE, TV AND/OR SATELLITE DISH CABLES, ETC. BEFORE WORK BEGINS. EQUIPMENT, MECHANICAL PIPING AND DUCTWORK INDICATED IS PARTIALLY DIAGRAMMATIC. CONTRACTOR SHALL DETERMINE IN FIELD EXACT LOCATION OF ALL DUCTWORK, PIPING AND EQUIPMENT. CONTRACTOR SHALL COORDINATE WITH ALL OTHER TRADES PRIOR TO INSTALLATION OF HIS/HER EQUIPMENT. UPON COMPLETION OF WORK THE CONTRACTOR SHALL CLEAN ALL DEBRIS FROM THE WORK AREA AND OTHER AREAS USED BY THE CONTRACTOR, AND LEAVE PREMISES IN A NEAT AND CLEAN CONDITION. CLEAN, PATCH AND REPAIR ALL WALLS, FLOORS, CEILINGS, AND OTHER SURFACES DAMAGED OR MARKED DURING CONSTRUCTION. ALL WORK SHALL COMPLY WITH THE MOST STRINGENT OF APPLICABLE CODES, ORDINANCES, AND REQUIREMENTS BY THE OWNER AND MANUFACTURER. COORDINATE DIFFUSER/GRILLE LOCATIONS WITH ARCHITECT. INSULATE ALL PIPING & DUCTWORK COMPLETE IN ACCORDANCE WITH THE PLANS, SPECIFICATIONS AND APPLICABLE ENERGY CODE. INSULATION WORK SHALL BE PERFORMED BY A COMPANY WHO'S PRIMARY FUNCTION IS MECHANICAL INSULATION INSTALLATION, AND SHALL HAVE A MINIMUM OF THREE YEARS DOCUMENTED EXPERIENCE. CONTRACTOR SHALL THOROUGHLY CLEAN ALL DUCTWORK AND EQUIPMENT COMPLETE AND INSTALL NEW FILTERS PRIOR TO AIR BALANCE. ALL DUCTWORK OPENINGS INCLUDING GRILLES AND DIFFUSERS SHALL BE SEALED AIR TIGHT UNTIL CONSTRUCTION IS 100% COMPLETE AND FINAL CLEANING HAS BEEN COMPLETED. INSTALL ALL EQUIPMENT IN STRICT ACCORDANCE WITH MANUFACTURERS WRITTEN INSTRUCTIONS. COORDINATE ALL MECHANICAL PIPING & DUCTWORK PENETRATIONS WITH STRUCTURAL PLANS AND SCHEDULES. CRITICAL INSTALLATION AREAS ARE INDICATED WITH DIMENSIONS. INSTALL FLEXIBLE DUCT CONNECTIONS AT ALL UNIT CONNECTIONS. ALL SUSPENDED EQUIPMENT SHALL BE ISOLATED FROM THE STRUCTURE WITH SPRING VIBRATION ISOLATORS AND KELLET PADS. INSTALL ALL SLAB MOUNTED EQUIPMENT EXCEPT FOR TANKS ON KELLET ISOLATOR PADS - NO EXCEPTIONS. INSULATE ALL HYDRONIC PIPING COMPLETE. B. C. D. E. F. G. H. I. J. K. L. DATE TA MON NA GISTERED RE John Hugh Melvin No. 10903PE ES GI SIO NAL EN THIS DRAWING IS THE PROPERTY OF THE ENGINEER. IT HAS BEEN PREPARED SPECIFICALLY FOR THIS SITE AND IS NOT TO BE USED FOR ANY OTHER PURPOSE, LOCATION, OR OWNER APPLICATION WITHOUT WRITTEN CONSENT OF THE ENGINEER. C 9 26"ø RA 4 4 4 4 4 6"ø 6"ø 6"ø 6"ø 4 6"ø 9' - 8" 6"ø 26"x26" SA 2015 JM ENGINEERING, PLLC EXISTING WALL CAP 10 10 DESCRIPTION OF PR 36"x36" SA 5. Furnish and install a new feed breaker in Panel ‘LP2’ for the new 75 HP Dust Collector Fan. Panel ‘LP2’ is an existing Square D 480Y/277 Volt, 3Ø, 225 Amp I-Line Panelboard. E.C. shall F&I a new 125 Amp, 3-Pole Type B-Frame #BGA34125Y I-Line Breaker in spaces 37,39,41. Pull (3) #1 CU Phase Wires, (1) #6 CU Ground Wire in a 1¼” EMT Conduit system. Fittings shall be compression type on interior/exterior of building with liquid seal-tite flexible conduit at equipment connection point. This equipment is fed via the Dust Collector Controller. Furnish and install a new feed breaker in Panel ‘LR2A’ for the new Dust Collector Controller. Panel ‘LR2A’ is an existing Square D Type ‘QO’ 208/120 Volt, 1Ø, 100 Amp Load Center. E.C. shall F&I a new 15 Amp, 1-Pole Type QO plug-on Breaker in space 23. Pull (1) #12 CU Phase Wire, (1) #12 CU Neutral Wire, (1) #12 CU Ground Wire in an ½” EMT Conduit system. E.C. shall connect all control interface wiring between the DC Controller and the DC Fan House. This shall include but not be limited to the GSX Touchscreen controller (two wires in conduit to the collector RPB Solenoid Box) and 120 V circuit for the solenoid heater. E.C. shall review and complete all requirements per the Dust Collector System installation documents. Raceway fittings shall be compression type on interior/exterior of building with liquid seal-tite flexible conduit at equipment connection point. Furnish and install a new feed breaker in Panel ‘LP2’ for the new 7.5 HP Air Compressor. E.C. shall F&I a new 20 Amp, 3-Pole Type B-Frame #BGA34020Y I-Line Breaker in spaces 19,21,23. Pull (3) #12 CU Phase Wires, (1) #12 CU Ground Wire in an ¾” EMT Conduit system. E.C. shall F&I a Square D Heavy-Duty Non-Fused Safety Disconnect Switch at the Air Compressor location. Fittings shall be compression type on interior of building with liquid seal-tite flexible conduit at equipment connection point. Furnish and install a new feed breaker in Panel ‘LP2’ for the new 1 HP Exhaust Fan. E.C. shall F&I a new 15 Amp, 3-Pole Type B-Frame #BGA34015Y I-Line Breaker in spaces 25,27,29. Pull (3) #12 CU Phase Wires, (1) #12 CU Ground Wire in an ¾” EMT Conduit system. E.C. shall F&I a Square D Combination Starter for the operation of this motor. E.C. shall F&I a local control switch station at the Foundry Hood location. Fittings shall be compression type on interior of building with liquid sealtite flexible conduit at equipment connection point. Furnish and install a new feed breaker in Panel ‘LP2’ for the new 2 HP Make-Up Air Unit. E.C. shall F&I a new 15 Amp, 3-Pole Type B-Frame #BGA34015Y I-Line Breaker in spaces 31,33,35. Pull (3) #12 CU Phase Wires, (1) #12 CU Ground Wire in an ¾” EMT Conduit system. E.C. shall F&I a Square D Combination Starter for the operation of this motor. E.C. shall connect the start circuit for this MAU to run when either the new Exhaust Fan for the Foundry Hood is turned on or the existing Exhaust Fan for the CNC Table is turned on. Fittings shall be compression type on interior of building with liquid seal-tite flexible conduit at equipment connection point. Furnish and install a new feed breaker in Panel ‘LR2A’ for the new Air Compressor – Refrigerated Air Dryer. E.C. shall F&I a new 15 Amp, 1-Pole Type QO plug-on Breaker in space 21. Pull (1) #12 CU Phase Wire, (1) #12 CU Neutral Wire, (1) #12 CU Ground Wire in an ½” EMT Conduit system to a NEMA 5-15R Power Receptacle. E.C. shall F&I a new #14 CU Type SO Cord and Industrial Cord Cap for the new Air Dryer. Raceway fittings shall be compression type on interior of building. GENERAL MECHANICAL/HYDRONIC NOTES SPECIFIC SHEET NOTES X N EE R ELECTRICAL SPECIFIC SHEET NOTES EX ISSUE ISSUE DATE: DATE REVISIONS 7 4 4 24"ø 23"ø 22"ø 20"ø 18"ø 17"ø 16"ø 15"ø 13"ø 12 24"ø 22"ø 14"ø EA 12 26"ø 9"ø 20"ø 4 15"ø 8 1"ø CA 11 11 12 4 4 4 13"ø 11"ø 9"ø 4 4 4 4 6"ø 6"ø 4 4 4 4 6"ø 11 13 6"ø 12 13"ø 22"ø SA 22"ø SA 4 AC 1 2300 Regent Street, Suite 207 Missoula, MT 59801 406.542.2849 www.jmengineering.net 7 9"ø 26"ø 1 14"ø EA 13"ø 4 9"ø 12 4 12 9"ø 20' SECTION PERFORATED DUCT 20' SECTION PERFORATED DUCT 12 MAU 1 2 17"x22" OA 6 4 14 6"ø 5 5 EF 1 14 "ø EA 4 9"ø 12 3 5 5 (E)Panel 'LP2' E1 PROJECT NO: (E)Panel 'LR2' E3 E4 E5 DRAWN BY: (E)Panel 'LR2A' E2 E6 CHECKED BY: 925 Gerald Ave., Missoula, MT 59801 4 Hellgate High School Welding Shop Dust Collection System 6"ø 4 22002 WH JM 4/7/2022 2:15:27 PM TO BURN TABLE ACROSS HALL 1 NORTH 1ST LEVEL MECHANICAL PLAN SCALE: 1/4" 1'-0" MAIN LEVEL MECHANICAL ELECTRICAL STRUCTURAL PLAN M101 Project Status (N) Dust Collector Control Panel
ISSUE ISSUE DATE: DATE REVISIONS DATE DESCRIPTION 0' - 8" PROVIDE ADEQUATE FLASHING AND SEALANT ON BOTH SIDES OF ALL THROUGH WALL PENETRATIONS. (E) MTL. DECK CONC. SLAB STL. BEAM 2ND LEVEL STRUCTURE STL. LINTEL AT (N) OPENING IN (E) BRICK WALL (SEE 1/M801) TA MON NA 0' - 4" GISTERED RE OF PR 26"ø RA John Hugh Melvin No. 10903PE 1' - 0" 1' - 0" 0' - 6" N EE R 36"x36" SA ES GI SIO NAL EN THIS DRAWING IS THE PROPERTY OF THE ENGINEER. IT HAS BEEN PREPARED SPECIFICALLY FOR THIS SITE AND IS NOT TO BE USED FOR ANY OTHER PURPOSE, LOCATION, OR OWNER APPLICATION WITHOUT WRITTEN CONSENT OF THE ENGINEER. 26"x26" SA C 2015 JM ENGINEERING, PLLC 1"ø CA 11' - 0" 2'-0" DC 1 AS REQ'D 11' - 8" 14' - 0" 26"ø RA 1'-0" 6" CONC. S.O.G. w/ #5 @ 12" (GR. 60) O.C. E.W., TOP (2" CVR.) (f'c 3,500 PSI) T.O. DUCT 111'-0" (MAX) #4 DOWELS @ 16" O.C. (GR. 60) T.O. SLAB 100'-0" #4 DOWELS @ 16" O.C. (GR. 60) THICKENED SLAB EDGE (16" WIDE x 12" MIN. BELOW GRADE) 1 ISOMETRIC 1 SCALE: CONTRACTOR RESPONSIBLE FOR ASPHALT CUTTING AND PATCH-BACK AS NEEDED TO INSTALL NEW CEMENT SLAB ON GRADE (SEE DEMO DM101) 2300 Regent Street, Suite 207 Missoula, MT 59801 406.542.2849 www.jmengineering.net GRADE FILL WITH ELASTOMERIC SEALANT ON TOP. 1/2" EXP. JOINT, TYP. @ (E) FOUNDATION (2)-#4 BAR *GR. 60) CONT., BOT. (TYP.) 4" MIN. CRUSHED/WASHED GRAVEL BASE NORTH 3 DUST COLLECTOR STRUCTURAL SECTION SCALE: 3/8" 1'-0" PROJECT NO: DRAWN BY: CHECKED BY: 925 Gerald Ave., Missoula, MT 59801 Hellgate High School Welding Shop Dust Collection System NORTH 22002 Author Checker 2 NORTH ISOMETRIC 2 SCALE: M701 Project Status 4/7/2022 2:15:29 PM MECHANICAL STRUCTURAL SECTIONS AND ISOMETRICS
ISSUE ISSUE DATE: DATE REVISIONS DATE DESCRIPTION DUST COLLECTOR SCHEDULE MARK MFR MODEL SERVICE CFM TSP RPM FILTER SURFACE AREA (FT 2) NUMBER OF FILTERS AIR TO CLOTH RATIO DC-1 CAMFIL GSX20 Lowboy w/ISMF METAL SHOP 21,700 13 1770 7,500 20 2.89 : 1 FAN POWER ELECTRICAL (VOLTAGE/ (HP) PHASE/ FREQUENCY) 75 WEIGHT (LBS) CONTROL REMARKS 8,100 VFD 1-7 480/3/60 NOTES: 1. PROVIDE 90 PSI COMPRESSED AIR HEADER WITH DIAPHRAM VALVES, PRESSURE GAUGE, AND THERMOSTATICALLY CONTROLLED SOLENOID HEATER (120/60/1). 2. PROVIDE FACTORY PROGRAMMED VFD WITH INTEGRAL DISCONNECT AND DUCT PRESSURE TRANSDUCER. 3. PROVIDE NEMA 4X ENCLOSURE FOR DUST COLLECTOR TIMER CONTROLS (120-240/60/1) WITH DIGITAL AND ANALOG DISPLAY, FILTER MONITORING, AND AUTOMATIC PULSE FILTER CLEANING. 4. PROVIDE WITH ACCOUSTICALLY LINED CLEAN AIR PLENUM, FAN SILENCER, LOW BOY DUST BIN(S). 5. PROVIDE WITH INTEGRATED HEPA SAFETY MONITORING FILTERS 6. SEE SPECIFICATIONS FOR INTERCONNECTION DETAILS 7. BASIS OF DESIGN LOCAL REPRESENTATIVE IS WYOMING MECHANICAL SUPPLY, (307) 685-7178. EXHAUST FAN SCHEDULE TA MON NA MARK MFR MODEL SERVICE CFM TSP RPM RATED BRAKE ELECTRICAL (VOLTAGE/ PHASE/ FREQUENCY) WEIGHT (LBS) SONES REMARKS EF-1 CAPTIVE AIRE SIF13DD FOUNDRY 2,000 0.8 1978 1 0.569 480/3/60 237 18.4 1 John Hugh Melvin No. 10903PE OF PR 1. PROVIDE WITH SQUARE TO ROUND DISCHARGE ADAPTOR, STANDARD 14" INLET DUCT CONNECTION, HORIZONTAL OVERHEAD MOUNT, HANDING SPRING VIBRATION ISOLATORS (SET OF 4) (HSA125), AND VFD FACTORY MOUNTED AND INCLUDED IN EXHAUST FAN. 2. PROVIDE OPERATION SWITCH NEAR FOUNDRY WITH LABEL. GISTERED RE N EE R POWER (HP) ES GI SIO NAL EN MAKE UP AIR UNIT SCHEDULE POWER (HP) THIS DRAWING IS THE PROPERTY OF THE ENGINEER. IT HAS BEEN PREPARED SPECIFICALLY FOR THIS SITE AND IS NOT TO BE USED FOR ANY OTHER PURPOSE, LOCATION, OR OWNER APPLICATION WITHOUT WRITTEN CONSENT OF THE ENGINEER. MARK MFR MODEL HOUSING BLOWER SERVICE CFM TSP RPM RATED BRAKE ELECTRICAL (VOLTAGE/ PHASE/ FREQUENCY) MAU-1 CAPTIVE AIRE A1-D.500-15D A1-D.500 15MF-1-MOD FOUNDRY/ PLASMA CNC TABLE EXHAUST 2,000 0.5 2165 2 1.388 480/3/60 BURNER C FLA MCA MOCP WEIGHT INPUT (BTU) OUTPUT (BTU) 2.7 4.4 15 744 180,421 165,987 EFFICIENCY TEMP RISE 97 90 2015 JM ENGINEERING, PLLC REMARKS 1,2 1. PROVIDE WITH INLEST PRESSURE GAUGE (0-35"), MANIFOLD PRESSURE GAUGE (-5 TO 15"), LOW FIRE START, AC INTERLOCK RELAY, MOTORIZED BACKDRAFT DAMPER, COMMERCIAL SMOKE DETECTOR/ALARM INTERLOCK, DOUBLE WALL STEEL LINER, FREEZESTAT, VRF FACTORY MOUNTED AND WIRED IN COMMERCIAL CONTROL VESTIBULE FOR TEMPERED SUPPLY FAN, LOAD AND LINE REACTOR MOUNTED IN FAN, DF1 INDOOR HANGING OPTION. 2. INTERLOCK OPERATION WITH FOUNDRY EXHAUST FAN AND CNC PLASMA TABLE EXHAUST FAN. AIR COMPRESSOR SCHEDULE MARK MFR MODEL SERVICE POWER (HP) STAGES FREE AIR FLOW RATE AT MAX PRESSURE (CFM) MAX OPERATING PRESSURE (PSI) TANK SIZE (GAL) OUTLET SIZE (IN) PUMP STYLE TYPE DUTY CYCLE AC-1 INGERSOL RAND 2475N7.5-P-460/3 METAL SHOP/ DUST COLLECTOR 8 2 24 175 80 3/4 RECIPROCATING SIMPLEX CONTINUOUS ELECTRICAL (VOLTAGE/ PHASE/ FREQUENCY) SOUND LEVEL (Dba) 85 480/3/60 REMARKS 1 MACHINE AND FOOT MOUNT BOLT NUT (LOCK WASHER CAN BE USED ON TOP OF FENDER WASHER) FENDER WASHER KELLET LP-13 WASHER BOLT SLEEVE KELLET LP-13 VIBRATION ISOLATION PAD Hellgate High School Welding Shop Dust Collection System 3. PROVIDE WITH FILTER, INGERSOLL RAND MODEL F35231400VS. PROJECT NO: DRAWN BY: IF BOLTED ALL THE WAY THROUGH, A SECOND KELLET LP-13 WASHER AND FENDER WASHER SHOULD BE USED CHECKED BY: 925 Gerald Ave., Missoula, MT 59801 2300 Regent Street, Suite 207 Missoula, MT 59801 406.542.2849 www.jmengineering.net 1. PROVIDE WITH TWO PRESSURE MANIFOLDS, ONE FOR THE DEDICATED DUST COLLECTOR @ 90PSI AND THE OTHER FOR THE EXISTING SHOP INFRASTRUCTURE @ 150PSI (VERIFY WITH EXISTING EQUIPMENT). 2. PROVIDE WITH REFRIGERATED AIR DRYER, INGERSOLL RAND MODEL D54IN ON LINE SERVING DUST COLLECTOR. PROVIDE WITH LITTLE GIANT VCMA-15ULS CONDENSATE PUMP AND ROUTE TUBING TO SINK IN ADJACENT ROOM. 22002 Author Checker FENDER WASHER 4/7/2022 2:15:29 PM NORTH 2 SMALL OPENING IN (E) BRICK MASONRY DTL. SCALE: 1/2" 1'-0" NORTH BOLT ISOLATION DETAIL SCALE: NO SCALE MECHANICAL STRUCTURAL SCHEDULES AND DETAILS M801 Project Status 1
duct mounted vertical fire / smoke damper flexible round duct mitered rectangular duct elbow with turning vanes 1.0 radius and 1.5 radius smooth round or oval elbow 1.0 radius and 1.5 radius 3-gore round or oval elbow 1.0 radius and 1.5 radius 5-gore round or oval elbow sharp-throat radius-heel rectangular duct elbow straight take-off conical .
524 montana ave missoula, mt 59802 101134 missoula, mineral cattle left rib horses left thigh byron r or tryg cooper 635 s 6th e missoula, mt 59801 101198 flathead, mineral, missoula cattle left hip horses left thigh the hardly able ranch 1349 quartz lp superior, mt 59872 100871 powell, missoula, teton, lewis & clark cattle left shoulder horses .
Missoula County Courthouse 200 West Broadway Missoula, Montana 59802 . Re: The United States' Investigation of the Missoula County Attorney's Office Dear Mr. VanValkenburg: As you know, for the last ten months, the Civil Rights Division ("Division"), in partnership with the U.S. Attorney's Office for the District ofMontana, has been engaged in an
Mattison. City-County Library of Missoula, headquarters for Tamarack Federation. The counties to be included in the demonstration in Tamarack Federation are Mineral, Ravalli and Lake. City-County Library of Missoula currently serves Missoula County. Lincoln County Free Library, which has served as headquarters for
PUBLIC INTEREST DEFENSE CENTER, PC P.O. Box 7584 Missoula, MT 59807 (406) 531-8133 publicdefense@gmail.com Timothy M. Bechtold BECHTOLD LAW FIRM, PLLC P.O. Box 7051 Missoula, MT 59807 (406) 721-1435 tim@bechtoldlaw.net Kristine Akland AKLAND LAW FIRM, PLLC PO Box 7274 Missoula, MT 59807 (406) 544-9863 aklandlawfirm@gmail.com
K-12 Comprehensive School Counseling Program ADOPTED May, 2012 This document was developed by the Missoula County Public Schools Curriculum Consortium, which includes Missoula County Public Schools
Missoula County Public Schools does not discriminate on the basis of race, color, national origin, sex, religion, creed, physical or mental disability, economic or social conditions, sexual orientation, gender identity, gender nonconformity, or actual or po
Development Centers" to "Technology and Development Centers" in recognition of their expanded role. Both centers were scheduled for new facili-ties during the 1960s. The Forest Service purchased land near the Missoula airport for the new facility in Missoula. The San Dimas, CA, center moved into it
to academic learning and the development of civic skills. This type of learning, called service-learning, strengthens . Missoula Missoula Missoula Polson St. Vincent Healthcare Foster Grandparent Program . National Center for Appropriate Technology National Ce
