STANDARD FOR TESTING SPECIFICATIONS Electrical Power .
ANSI/NETA MTS-2011AMERICAN NATIONAL STANDARDSTANDARD FORMAINTENANCE TESTING SPECIFICATIONS forElectrical Power Equipmentand SystemsSecretariatNETA (InterNational Electrical Testing Association)Approved byAmerican National Standards Institute
– This page intentionally left blank –
AmericanNationalStandardApproval of an American National Standard requires verification byANSI that the requirements for due process, consensus, and othercriteria for approval have been met by the standards developer.Consensus is established when, in the judgment of the ANSI Board ofStandards Review, substantial agreement has been reached by directlyand materially affected interests. Substantial agreement means muchmore than a simple majority, but not necessarily unanimity. Consensusrequires that all views and objections be considered, and that a concertedeffort be made toward their resolution.The use of American National Standards is completely voluntary; theirexistence does not in any respect preclude anyone, whether he hasapproved the standards or not, from manufacturing, marketing,purchasing, or using products, processes, or procedures not conformingto the standards.The American National Standards Institute does not develop standardsand will in no circumstances give an interpretation of any AmericanNational Standard in the name of the American National StandardsInstitute. Requests for interpretations should be addressed to thesecretariat or sponsor whose name appears on the title page of thisstandard.Caution Notice: This American National Standard may be revised orwithdrawn at any time. The procedures of the American NationalStandards Institute require that action be taken periodically to reaffirm,revise, or withdraw this standard. Purchasers of American NationalStandards may receive current information on all standards by calling orwriting the American National Standards Institute.Published byInterNational Electrical Testing Association3050 Old Centre Ave., Suite 102Portage, MI 49024269.488.6382· FAX ne Tanz - Executive DirectorCopyright 2011InterNational Electrical Testing AssociationAll rights reservedPrinted in the United States of AmericaNo part of this publication may be reproduced in any form, in anelectronic retrieval system or otherwise, without the prior writtenpermission of the publisher.ANSI/NETA MTS-2011
Copyright Information andAlteration of Content2011 ANSI/NETA Standard for Maintenance Testing Specifications is protected under thecopyright laws of the United States, and all rights are reserved. Further, the Standard maynot be copied, modified, sold, or used except in accordance with such laws and as follows:Purchasers may reproduce and use all or a portion of the Standard provided ANSI/NETAStandard for Maintenance Testing Specifications is clearly identified in writing as the sourceof all such uses or reproductions.Section 7 of the ANSI/NETA Standard for Maintenance Testing Specifications may bereproduced and used on a “cut and paste” basis for the particular type of equipment to betested.The following sections of the ANSI/NETA Standard for Maintenance Testing Specificationsmust be incorporated by reference as part of any subsection:3.4.5.Qualifications of Testing Organization and Personnel3.1Testing Organization3.2Testing PersonnelDivision of Responsibility4.1The Owner’s Representative4.2The Testing OrganizationGeneral5.1Safety and Precaution5.2Suitability of Test Equipment5.3Test Instrument Calibration5.4Test ReportThe purchaser is required to include the above sections with any section(s) of 7. Copyright 2011InterNational Electrical Testing Association3050 Old Centre Ave., Suite 102Portage, MI 49024Voice: 888.300.6382 Facsimile: 269.488.6383E-mail: neta@netaworld.org Web: www.netaworld.orgANSI/NETA MTS-2011
Standards Review CouncilThe following persons were members of the NETA Standards Review Council which approved thisdocument.Charles K. Blizard, Sr.Timothy J. CotterDiane W. HagemanRoderic L. HagemanDave HuffmanRalph PattersonAlan D. PetersonJayne TanzRon WidupMaintenance Testing Specifications Section Panel MembersThe following persons were members of the Section Panel which balloted on this document for submissionto the NETA Standards Review Council.Mark BaldwinKen BassettTom BishopScott BlizardMichael BowersAlan BumpJohn CadickMichel CanstonguayErnie CreechTim CrnkoDon GenutisKerry HeidStuart JacksonScott KinneyAndrew KoblerKorey KruseBenjamin LanzMark LautenschlagerJoe NimsBruce OlsonANSI/NETA MTS-2011Jerry ParnellRaj PatelTony PerryM. Lee Perry, Jr.Mose Ramieh, Sr.Vince SaporitaRichard SobhrajChrisWerstiukJohn WhiteJ.P. Wolff
NETA Accredited CompaniesThe following persons were voting members of the InterNational Electrical Testing Associationwhen this document was approved on May 16, 2011.A&F Electrical Testing., Inc.Kevin ChiltonAdvanced Testing SystemsPatrick MacCarthyAmerican Electrical Testing Co., Inc.Scott BlizardApparatus Testing and EngineeringJames LawlerApplied Engineering ConceptsMichel CastonguayBurlington Electrical Testing Company, Inc.C.E. Testing., Inc.Walter ClearyMark ChapmanCE Power Solutions of Wisconsin, LLCJames VanHandelDYMAX Holdings, Inc.Gene PhilippEastern High VoltageJoseph WilsonELECT, P.C.Barry W. TyndallElectric Power Systems, Inc.Steve ReedElectrical and Electronic ControlsMichael HughesElectrical Energy Experts, Inc.William StyerElectrical Equipment Upgrading, Inc.Kevin MillerElectrical Maintenance & Testing, Inc.Brian BorstElectrical Reliability ServicesLee BighamElectrical Testing, Inc.Steve DoddElemco Services, Inc.Robert J. WhiteHampton Tedder Technical ServicesMatt TedderHarford Electrical Testing Co., Inc.Vincent BiondinoHigh Energy Electrical Testing, Inc.James P. RatshinHigh Voltage Maintenance Corp.Eric NationHMT, Inc.John PertgenIndustrial Electric Testing, Inc.Gary BenzenbergIndustrial Electronics GroupButch E. TealIndustrial Tests, Inc.Greg PooleInfra-Red Building and Power ServiceThomas McDonaldANSI/NETA MTS-2011
NETA Accredited CompaniesM&L Power Systems Maintenance, Inc.Darshan AroraMagna Electric CorporationKerry HeidMagna IV Engineering – EdmontonJereme WentzellMagna IV Engineering (BC), Ltd.Cameron HiteMET Electrical Testing, LLCWilliam McKenzieNational Field ServicesEric BeckmanNationwide Electrical Testing, Inc.Shashikant B. BagleNorth Central Electric, Inc.Robert MessinaNorthern Electrical Testing, Inc.Lyle DettermanOrbis Engineering Field ServicesLorne GaraPacific Power Testing, Inc.Steve EmmertPhasor EngineeringRafael CastroPotomac Testing, Inc.Ken BassettPower & Generation Testing, Inc.Mose RamiehPower Engineering Services, Inc.Miles R. EngelkePOWER PLUS Engineering, Inc.Salvatore MancusoPower Products & Solutions, Inc.Ralph PattersonPower Services, LLCGerald BydashPower Systems Testing Co.David HuffmanPower Test, Inc.Richard WalkerPOWER Testing and Energization, Inc.Chris ZavadlovPowertech Services, Inc.Jean A. BrownPrecision Testing GroupGlenn StuckeyPRIT Service, Inc.Roderic HagemanReuter & Hanney, Inc.Michael ReuterREV Engineering, LTDRoland DavidsonScott Testing, Inc.Russ SorbelloShermco IndustriesRon WidupSigma Six Solutions, Inc.John WhiteSouthern New England Electrical TestingDavid Asplund, Sr.ANSI/NETA MTS-2011
NETA Accredited CompaniesSouthwest Energy Systems, LLCRobert SheppardTaurus Power and Controls, Inc.Rob BulfinchThree-C Electrical Co., Inc.James CialdeaTidal Power Services, LLCMonty JanakTony Demaria Electric, Inc.Anthony DemariaTrace Electrical Services & Testing, LLCJoseph VastaUtilities Instrumentation Service, Inc.Gary WallsUtility Service CorporationAlan PetersonWestern Electrical ServicesDan HookANSI/NETA MTS-2011
NOTICEIn no event shall the InterNational Electrical Testing Association be liable to anyone for special, collateral,incidental, or consequential damages in connection with or arising out of the use of these materials.This document is subject to periodic review, and users are cautioned to obtain the latest edition. Commentsand suggestions are invited from all users for consideration by the Association in connection with suchreview. Any such suggestions will be fully reviewed by the Association after giving the commenter, uponrequest, a reasonable opportunity to be heard.This document should not be confused with federal, state, or municipal specifications or regulations,insurance requirements, or national safety codes. While the Association recommends reference to or use ofthis document by government agencies and others, use of this document is purely voluntary and not binding.InterNational Electrical Testing Association3050 Old Centre Ave., Suite 102 Portage, MI 49024Voice: 888.300.6382 Facsimile: 269.488.6383Email: neta@netaworld.org Web: www.netaworld.orgJayne Tanz, CMP - Executive DirectorANSI/NETA MTS-2011
– This page intentionally left blank –ANSI/NETA MTS-2011
FOREWORD(This Foreword is not part of American National Standard ANSI/NETA MTS-2011)The InterNational Electrical Testing Association (NETA) was formed in 1972 to establish uniform testingprocedures for electrical equipment and apparatus. NETA has been an Accredited Standards Developer forthe American National Standards Institute since 1996. NETA’s scope of standards activity is different fromthat of IEEE, NECA, NEMA, and UL. In matters of testing electrical equipment and systems NETAcontinues to reference other standards developers’ documents where applicable. NETA’s review andupdating of presently published standards takes into account both national and international standards.NETA’s standards may be used internationally as well as in the United States. NETA firmly endorses aglobal standardization. IEC standards as well as American consensus standards are taken into considerationby NETA’s ballot pools and reviewing committees.The first NETA Maintenance Testing Specifications for Electrical Power Equipment and Systems waspublished in 1975. Since 1989, revised editions of the Maintenance Testing Specifications have beenpublished in 1993, 1997, and 2001.In 2005, this document was approved for the first time as an American National Standard. The 2011Standard for Maintenance Testing Specifications for Electrical Power Equipment and Systems is the mostcurrent revision of this document.The ANSI/NETA Standard for Maintenance Testing Specifications for Electrical Power Equipment andSystems was developed for use by those responsible for the continued operation of existing electricalsystems and equipment to guide them in specifying and performing the necessary tests to ensure that thesesystems and apparatus perform satisfactorily, minimizing downtime and maximizing life expectancy. Thisdocument aids in ensuring safe, reliable operation of existing electrical power systems and equipment.Maintenance testing can identify potential problem areas before they become major problems requiringexpensive and time-consuming solutions.Suggestions for improvement of this standard are welcome. They should be sent to the InterNationalElectrical Testing Association, 3050 Old Centre Avenue, Suite 102, Portage, MI 49024.ANSI/NETA MTS-2011
PREFACEIt is recognized by the Association that the needs for maintenance testing of commercial, industrial,governmental, and other electrical power systems vary widely. Many criteria are used in determining whatequipment is to be tested and to what extent.To help the user better understand and navigate more efficiently through this document, we offer thefollowing information:The Document StructureThe document is divided into twelve separate and defined sections:SectionSection 1Section 2Section 3Section 4Section 5Section 6Section 7Section 8Section 9Section 10TablesAppendicesDescriptionGeneral ScopeApplicable ReferencesQualifications of Testing Organization and PersonnelDivision of ResponsibilityGeneralPower System StudiesInspection and Test ProceduresSystem Function TestThermographic SurveyElectromagnetic Field TestingReference TablesVarious Informational DocumentsSection 7 StructureSection 7 is the main body of the document with specific information on what to do relative to theinspection and maintenance testing of electrical power distribution equipment and systems. It is not intendedthat this document explain how to test specific pieces of equipment or systems.Expected Test ResultsSection 7 consists of sections specific to each particular type of equipment. Within those sections there are,typically, three main bodies of information:1. Visual and Mechanical Inspection2. Electrical Tests3. Test ValuesANSI/NETA MTS-2011
PREFACE (continued)Results of Visual and Mechanical InspectionsSome, but not all, visual and mechanical inspections have an associated test value or result. Those itemswith an expected result are referenced under Section 3.1 Test Values – Visual and Mechanical. Forexample, Section 7.1 Switchgear and Switchboard Assemblies, item 7.1.1.7.2 calls for verifying tightness ofconnections using a calibrated torque wrench method. Under the Test Values – Visual and MechanicalSection 7.1.3. 1.2, the expected results for that particular task are listed within Section 3.1, with referenceback to the original task description on item 7.1.1.7.2.ANSI/NETA MTS-2011
PREFACE (continued)Results of Electrical TestsEach electrical test has a corresponding expected result, and the test and the result have identical numbers. Ifthe electrical test is item four, the expected result under the Test Values section is also item four. Forexample, under Section 7.15.1 Rotating Machinery, AC Induction Motors and Generators, item 7.15.1.2.2(item 2 within the Electrical Tests section) calls for performing an insulation-resistance test in accordancewith IEEE Standard 43. Under the Test Values – Electrical section, the expected results for that particulartask are listed in the Test Values section under item 2.ANSI/NETA MTS-2011
PREFACE (continued)Optional TestsThe p
Standard for Maintenance Testing Specifications is clearly identified in writing as the source of all such uses or reproductions. Section 7 of the ANSI/NETA Standard for Maintenance Testing Specifications may be reproduced and used on a “cut and paste” basis for the particular type of equipment to be tested.
Bruksanvisning för bilstereo . Bruksanvisning for bilstereo . Instrukcja obsługi samochodowego odtwarzacza stereo . Operating Instructions for Car Stereo . 610-104 . SV . Bruksanvisning i original
Hotell För hotell anges de tre klasserna A/B, C och D. Det betyder att den "normala" standarden C är acceptabel men att motiven för en högre standard är starka. Ljudklass C motsvarar de tidigare normkraven för hotell, ljudklass A/B motsvarar kraven för moderna hotell med hög standard och ljudklass D kan användas vid
10 tips och tricks för att lyckas med ert sap-projekt 20 SAPSANYTT 2/2015 De flesta projektledare känner säkert till Cobb’s paradox. Martin Cobb verkade som CIO för sekretariatet för Treasury Board of Canada 1995 då han ställde frågan
service i Norge och Finland drivs inom ramen för ett enskilt företag (NRK. 1 och Yleisradio), fin ns det i Sverige tre: Ett för tv (Sveriges Television , SVT ), ett för radio (Sveriges Radio , SR ) och ett för utbildnings program (Sveriges Utbildningsradio, UR, vilket till följd av sin begränsade storlek inte återfinns bland de 25 största
LÄS NOGGRANT FÖLJANDE VILLKOR FÖR APPLE DEVELOPER PROGRAM LICENCE . Apple Developer Program License Agreement Syfte Du vill använda Apple-mjukvara (enligt definitionen nedan) för att utveckla en eller flera Applikationer (enligt definitionen nedan) för Apple-märkta produkter. . Applikationer som utvecklas för iOS-produkter, Apple .
och krav. Maskinerna skriver ut upp till fyra tum breda etiketter med direkt termoteknik och termotransferteknik och är lämpliga för en lång rad användningsområden på vertikala marknader. TD-seriens professionella etikettskrivare för . skrivbordet. Brothers nya avancerade 4-tums etikettskrivare för skrivbordet är effektiva och enkla att
Den kanadensiska språkvetaren Jim Cummins har visat i sin forskning från år 1979 att det kan ta 1 till 3 år för att lära sig ett vardagsspråk och mellan 5 till 7 år för att behärska ett akademiskt språk.4 Han införde två begrepp för att beskriva elevernas språkliga kompetens: BI
**Godkänd av MAN för upp till 120 000 km och Mercedes Benz, Volvo och Renault för upp till 100 000 km i enlighet med deras specifikationer. Faktiskt oljebyte beror på motortyp, körförhållanden, servicehistorik, OBD och bränslekvalitet. Se alltid tillverkarens instruktionsbok. Art.Nr. 159CAC Art.Nr. 159CAA Art.Nr. 159CAB Art.Nr. 217B1B
