USB Cable Installation Guide (UG344) - Xilinx

3y ago
90 Views
3 Downloads
1.39 MB
26 Pages
Last View : 2m ago
Last Download : 2m ago
Upload by : Kaleb Stephen
Transcription

USB CableInstallation GuideUG344 (v2.2) July 28, 2016R

RDISCLAIMERThe information disclosed to you hereunder (the “Materials”) is provided solely for the selection and use of Xilinx products. To the maximumextent permitted by applicable law: (1) Materials are made available "AS IS" and with all faults, Xilinx hereby DISCLAIMS ALLWARRANTIES AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING BUT NOT LIMITED TO WARRANTIES OFMERCHANTABILITY, NON-INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and (2) Xilinx shall not be liable (whetherin contract or tort, including negligence, or under any other theory of liability) for any loss or damage of any kind or nature related to, arisingunder, or in connection with, the Materials (including your use of the Materials), including for any direct, indirect, special, incidental, orconsequential loss or damage (including loss of data, profits, goodwill, or any type of loss or damage suffered as a result of any actionbrought by a third party) even if such damage or loss was reasonably foreseeable or Xilinx had been advised of the possibility of the same.Xilinx assumes no obligation to correct any errors contained in the Materials or to notify you of updates to the Materials or to productspecifications. You may not reproduce, modify, distribute, or publicly display the Materials without prior written consent. Certain products aresubject to the terms and conditions of Xilinx’s limited warranty, please refer to Xilinx’s Terms of Sale which can be viewed atwww.xilinx.com/legal.htm#tos; IP cores may be subject to warranty and support terms contained in a license issued to you by Xilinx. Xilinxproducts are not designed or intended to be fail-safe or for use in any application requiring fail-safe performance; you assume sole risk andliability for use of Xilinx products in such critical applications, please refer to Xilinx’s Terms of Sale which can be viewed atwww.xilinx.com/legal.htm#tos. Copyright 2007–2016 Xilinx, Inc. Xilinx, the Xilinx logo, Artix, ISE, Kintex, Spartan, Virtex, Vivado, Zynq, and other designated brandsincluded herein are trademarks of Xilinx in the United States and other countries. All other trademarks are the property of their respectiveowners.Revision HistoryThe following table shows the revision history for this document.DateVersion02/02/20071.0Initial Xilinx release.03/06/20082.0 Added support for Platform Cable USB II (DLC10). Added support for Windows Vista. Added Figure 1-2, page 12 and Figure 1-3, page 13 to address Windows Vista securitydialog boxes. Updated “Step 4: Determine Installation Flow,” page 14 for Linux operating systems. Simplified “Step 5: Install the Xilinx USB Cable,” page 17 for Windows operatingsystems. Updated download links for Windows and Linux cable driver installers. Updated document template. Numerous minor edits to enhancements clarity.02/17/20092.0.1USB Cable Installation GuideRevision Removed link to Platform Cable USB Data Sheet in “Additional Documentation,”page 7.www.xilinx.comUG344 (v2.2) July 28, 2016

DateVersionRevision01/20/20142.1The Windows 7 Professional 32- and 64-bit operating system was added to Table 1,page 8 and to “For Windows 7, Windows XP, or Windows 2000 Professional OperatingSystems,” page 17.07/28/20162.2 Differentiated between ISE WebPACK and Vivado WebPACK, and added sentenceabout cable driver installation for Vivado tools to first paragraph of “About ThisGuide.” Updated URLs in “Additional Documentation.” Removed reference to Xilinx interactive configuration problem solver from“Additional Resources.”UG344 (v2.2) July 28, 2016www.xilinx.comUSB Cable Installation Guide

USB Cable Installation Guidewww.xilinx.comUG344 (v2.2) July 28, 2016

Table of ContentsPreface: About This GuideGuide Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Additional Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Supported Xilinx Software and Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . .Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77889Typographical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Online Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Chapter 1: Installing Xilinx USB CablesStep 1: Install ISE or WebPACK Design Tool Software and USB Cable Drivers 11Step 2: Find the Cable Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Step 3: Find the ISE or WebPACK Design Tool Software Version . . . . . . . . . . . . 14Step 4: Determine Installation Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14For Windows XP Professional or 2000 Professional . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14For Windows Vista . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15For Red Hat Enterprise Linux WS or SUSE Linux Enterprise . . . . . . . . . . . . . . . . . . . . 16Step 5: Install the Xilinx USB Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17For Windows 7, Windows XP, or Windows 2000 Professional Operating Systems . 17On All Linux Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Chapter 2: Found New Hardware WizardRunning the New Hardware Wizard (Windows XP Professional Only) . . . . . . . 19Appendix A: Known IssuesWindows Found New Hardware Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23'Wizard Cannot Install this Hardware' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23USB Cable Installation GuideUG344 (v2.2) July 28, 2016www.xilinx.com5

R6www.xilinx.comUSB Cable Installation GuideUG344 (v2.2) July 28, 2016

RPrefaceAbout This GuideThis guide explains how to install the Xilinx family of USB programming cables, includinginformation related to installing Xilinx USB cables with ISE and ISE WebPACK designtool software. For updated information, see Xilinx Answer 54381. For information on cabledriver installation for the Vivado tools including the Vivado WebPACK edition, seeUG973, Vivado Design Suite User Guide: Release Notes, Installation, and Licensing.Guide ContentsThis manual contains the following chapters: Chapter 1, “Installing Xilinx USB Cables,” provides step-by-step installationprocedure. Chapter 2, “Found New Hardware Wizard,” explains installation using this wizard. Appendix A, “Known Issues,” covers known issues that can occur during theinstallation procedure.Additional Documentation1.DS593, Platform Cable USB II Data SheetThis data sheet provides a complete description of the Platform Cable USB IIhardware, including operation and electrical characteristics.2.Platform Cable USB Frequently Asked Questions (FAQ)This FAQ contains supplemental information for the Platform Cable USB.3.ISE Design Suite Software ManualsThe ISE tools software manuals provide software installation instructions, pointers toadditional online documentation and listings of known issues.4.The ISE Release Notes contains WebPACK-specific information supplementing the ISESoftware Manual. This includes additional software download and installationinformation, as well as ISE WebPACK design tool device and feature support.To find additional documentation, see the Xilinx website at:www.xilinx.com/literature.USB Cable Installation GuideUG344 (v2.2) July 28, 2016www.xilinx.com7

Preface:RAbout This GuideAdditional ResourcesTo search the answer database of silicon, software, and IP questions and answers, or tocreate a technical support WebCase, see the Xilinx website at:www.xilinx.com/supportSupported Xilinx Software and Operating SystemsISE Design Suite WebPACK tool software must be installed on a supported operatingsystem before any Xilinx USB cable can be used. The following table lists operating systemand Xilinx software combinations that can be used with Xilinx USB cables.Table 1:Supported Operating Systems and ISE or WebPACK Tool VersionsOperating SystemISE or WebPACK Design Tool VersionWindows 2000 Professional SP46.3.03i or laterWindows XP Professional 32-bit6.3.03i or laterWindows XP Professional 64-bit9.1i or laterWindows Vista 32- and 64-bit9.2 or laterWindows 7 Professional 32- and 64-bit13.1 or laterRed Hat Enterprise Linux WS 3.0 32-bit7.1i or laterRed Hat Enterprise Linux WS 3.0 64-bit9.1i or laterRed Hat Enterprise Linux WS 4.0 32-bit8.2i or laterRed Hat Enterprise Linux WS 4.0 64-bit9.1i or laterRed Hat Enterprise Linux WS 5.0 32-bit and 64-bit9.2i or laterSUSE Linux Enterprise 10.0 32- and 64-bit10.1 or laterNotes:1. The operating systems supported by Xilinx USB cables are a sub-set of the operating systemssupported by the ISE or WebPACK design tool software.2. WebPACK software is a free application available on the Xilinx ISE CD/DVD or for download suite/ise-webpack.html.8www.xilinx.comUSB Cable Installation GuideUG344 (v2.2) July 28, 2016

RConventionsConventionsThis document uses the following conventions. An example illustrates each convention.TypographicalThe following typographical conventions are used in this document:ConventionMeaning or UseExampleCourier fontMessages, prompts, andprogram files that the systemdisplaysspeed grade: - 100Courier boldLiteral commands that you enterin a syntactical statementngdbuild design nameCommands that you select froma menuFile OpenKeyboard shortcutsCtrl CVariables in a syntax statementfor which you must supplyvaluesngdbuild design nameReferences to other manualsSee the Development SystemReference Guide for moreinformation.Emphasis in textIf a wire is drawn so that itoverlaps the pin of a symbol, thetwo nets are not connected.An optional entry or parameter.However, in bus specifications,such as bus[7:0], they arerequired.ngdbuild [option name]design nameA list of items from which youmust choose one or morelowpwr {on off}Separates items in a list ofchoiceslowpwr {on off}Vertical ellipsis.Repetitive material that hasbeen omittedIOB #1: Name QOUT’IOB #2: Name CLKIN’.Horizontal ellipsis . . .Repetitive material that hasbeen omittedallow block block name loc1loc2 . locn;Helvetica boldItalic fontSquare bracketsBraces{ }Vertical barUSB Cable Installation GuideUG344 (v2.2) July 28, 2016[ ] www.xilinx.com9

Preface:RAbout This GuideOnline DocumentThe following conventions are used in this document:Convention10Meaning or UseExampleSee the section “AdditionalResources” for details.Blue textCross-reference link to a locationin the current documentRed textCross-reference link to a locationin another documentSee Figure 2-5 in the Virtex-IIPlatform FPGA User Guide.Blue, underlined textHyperlink to a website (URL)Go to www.xilinx.com for thelatest speed files.www.xilinx.comRefer to “Title Formats” inChapter 1 for details.USB Cable Installation GuideUG344 (v2.2) July 28, 2016

RChapter 1Installing Xilinx USB CablesProprietary device drivers must be installed to allow ISE Design Suite and WebPACK design tool software (for example, iMPACT) to communicate with Xilinx USB cables.Installation flows can differ depending on: USB cable model ISE or WebPACK design tool software version PC operating systemIn general, a complete USB cable installation is performed automatically when the latestISE or ISE WebPACK design tool software is installed. However, additional actions mightbe necessary if, for example, the cable is to be installed on a Linux operating system.Another example is if Platform Cable USB II (Model DLC10) is to be used with ISE orWebPACK design tool software versions prior to 10.1.This chapter is organized to provide you with a step-by-step and system-specificprocedure for installing Xilinx USB cables. There are five steps required for installation:Step 1: Install ISE or WebPACK Design Tool Software and USB Cable DriversStep 2: Find the Cable ModelStep 3: Find the ISE or WebPACK Design Tool Software VersionStep 4: Determine Installation FlowStep 5: Install the Xilinx USB CableIt is highly recommended that you start with Step 1: Install ISE or WebPACK Design ToolSoftware and USB Cable Drivers and follow the procedure in order.Step 1: Install ISE or WebPACK Design Tool Software and USBCable Drivers1.Install the ISE or WebPACK design tool software. See the appropriate installation guideor WebPACK tool software FAQ (see “Additional Documentation” in “About ThisGuide”).2.During ISE or WebPACK tool software installation, confirm that the cable drivers areselected (Figure 1-1) to ensure that the drivers are copied from the installation media tothe target system.Note: Cable drivers are not selected by default for Linux versions of ISE and WebPACK toolsoftware.The window shown in Figure 1-1 does not appear when installing WebPACK - LabInstall (Programming Tools Only). The cable drivers are installed automatically withthis application.USB Cable Installation GuideUG344 (v2.2) July 28, 2016www.xilinx.com11

RChapter 1: Installing Xilinx USB CablesNote: The window shown in Figure 1-1 can vary for different ISE design tool releases.X-Ref Target - Figure 1-1UG344 C1 01 022008Figure 1-1:3.ISE 10.1 Design Suite Installer(Windows Vista only) During installation, two Windows Security dialog boxes mightappear: one for the Jungo driver (Figure 1-2) and one for Xilinx cable driver(Figure 1-3). In both instances, check the box next to Always trust software from"XXXX" and then click Install.X-Ref Target - Figure 1-2UG344 C01 02 021708Figure 1-2:12Windows Security Dialog Box for the Jungo Driver(Windows Vista Only)www.xilinx.comUSB Cable Installation GuideUG344 (v2.2) July 28, 2016

RStep 2: Find the Cable ModelX-Ref Target - Figure 1-3UG344 C01 03 021708Figure 1-3:Windows Security Dialog Box for the Xilinx Cable Driver(Windows Vista Only)Step 2: Find the Cable Model1.Find and record the model number of the USB cable. The model number is printed onthe label attached to the cable case (Figure 1-4). Table 1-1 shows a complete list ofXilinx USB cable models.X-Ref Target - Figure 1-4UG344 C01 02 030508Figure 1-4:Model Number on a USB CableTable 1-1: Xilinx USB Cables2.USB Cable Installation GuideUG344 (v2.2) July 28, 2016NameModelPlatform Cable USB IIDLC10Platform Cable USBDLC9GPlatform Cable USBDLC9LPPlatform Cable USBDLC9Proceed to “Step 3: Find the ISE or WebPACK Design Tool Software Version.”www.xilinx.com13

RChapter 1: Installing Xilinx USB CablesStep 3: Find the ISE or WebPACK Design Tool Software VersionFind and record the ISE or WebPACK tool software version installed on the host system.Version information can be found using the Project Navigator or iMPACT GUI:1.Launch the ISE Project Navigator or iMPACT.2.From the pull-down menus near the top of the GUI, select Help.3.Select About 4.A dialog box similar to Figure 1-5 appears. Record the release version.5.Proceed to “Step 4: Determine Installation Flow.”X-Ref Target - Figure 1-5UG344 C01 03 022808Figure 1-5:Finding the ISE Software VersionStep 4: Determine Installation FlowAfter determining the cable model number and ISE or WebPACK design tool softwareversion, select the installation flow based on the host PC operating system.For Windows XP Professional or 2000 ProfessionalFor model DLC10For ISE or WebPACK design tool software version: 10.1 or later:Cable installation was completed during ISE or WebPACK design tool softwareinstallation. No further actions are required. 6.3.03i through 9.2.04i:Proceed to “Step 5: Install the Xilinx USB Cable.”Note: Xilinx recommends updating to the latest ISE or WebPACK design tool software versionto obtain current USB cable enhancements and fixes. 6.3.02i or earlier:Xilinx USB cables are not supported. Upgrade to a supported ISE or WebPACK designtool software version and then return to this step.14www.xilinx.comUSB Cable Installation GuideUG344 (v2.2) July 28, 2016

RStep 4: Determine Installation FlowFor Model DLC9LP or DLC9GFor ISE or WebPACK design tool software version: 8.2i or later:Cable installation was completed during ISE or WebPACK tool software installation.No further actions are required. 6.3.03i through 8.1.03i:Proceed to “Step 5: Install the Xilinx USB Cable.”Note: Xilinx recommends updating to the latest ISE or WebPACK tool software version toobtain current USB cable enhancements and fixes. 6.3.02i or earlier:Xilinx USB cables are not supported. Upgrade to a supported ISE or WebPACK toolsoftware version and then return to this step.For Model DLC9For ISE or WebPACK design tool software version: 7.1i or later:Cable installation was completed during ISE or WebPACK design tool softwareinstallation. No further actions are required. 6.3.03i (only):Proceed to “Step 5: Install the Xilinx USB Cable.”Note: Xilinx recommends updating to the latest ISE or WebPACK design tool software versionto obtain current USB cable enhancements and fixes. 6.3.02i or earlier:Xilinx USB cables are not supported. Upgrade to a supported ISE or WebPACK designtool software version and then return to this step.For Windows VistaFor Model DLC10For ISE or WebPACK design tool software version: 10.1 or later:Cable installation was completed during ISE or WebPACK design tool softwareinstallation. No further actions are required. 9.2i through 9.2.04i:Proceed to “Step 5: Install the Xilinx USB Cable.”Note: Xilinx recommends updating to the latest ISE or WebPACK design tool software versionto obtain current USB cable enhancements and fixes. 9.1.03i or earlier:ISE and WebPACK tool software versions prior to 9.2i are not supported on WindowsVista. Upgrade to a supported ISE or WebPACK design tool software version and thenreturn to this step.USB Cable Installation GuideUG344 (v2.2) July 28, 2016www.xilinx.com15

RChapter 1: Installing Xilinx USB CablesFor Model DLC9LP, DLC9G or DLC9For ISE or WebPACK design tool software version: 9.2i or later:Cable installation was completed during ISE or WebPACK design tool softwareinstallation. No further actions are required. 9.1.03i or earlier:ISE and WebPACK software versions prior to 9.2i are not supported on Windows Vista.Upgrade to a supported ISE or WebPACK design tool software version and then returnto this step.For Red Hat Enterprise Linux WS or SUSE Linux EnterpriseFor Model DLC10For ISE or WebPACK design tool software version: 10.1 or later:Use Table 1-1, page 13 to verify that the Linux operating system installed on the hostsupports Xilinx USB cables. If USB cables are supported, then cable installation wascompleted during the ISE or WebPACK design tool software installation and nofurther actions are required. Otherwise, upgrade to a supported Linux operatingsystem and re-install the Xilinx design tool to complete the installation. 7.1i through 9.2.04i:Use Table 1-1 to verify that the Linux operating system installed on the host supportsXilinx USB cables. If USB cables are supported, then proceed to “Step 5: Install theXilinx USB Cable.” Otherwise, upgrade to a supported Linux operating system, reinstall the Xilinx design tool, and then return to this step.Note: Xilinx recommends updating to the latest ISE or WebPACK design tool software versionto obtain current USB cable enhancements and fixes. 6.3.03i or earlier:Xilinx USB cables are not supported. Upgrade to a supported ISE or WebPACK designtool software version and then return to this step.For Model DLC9LP, DLC9G or DLC9For ISE or WebPACK design tool software versi

Windows XP Professional 32-bit 6.3.03i or later Windows XP Professional 64-bit 9.1i or later Windows Vista 32- and 64-bit 9.2 or later Windows 7 Professional 32- and 64-bit 13.1 or later Red Hat Enterprise Linux WS 3.0 32-bit 7.1i or later Red Hat Enterprise Linux WS 3.0 64-bit 9.1i or later Red Hat Enterprise Linux WS 4.0 32-bit 8.2i or later

Related Documents:

In-box 1m cable or Jabra 1.8m cable How to connect using Anker PowerLine/Newnex cable USB-A USB-C 3m USB-A to USB-C cable How to connect using Startech USB 3.0/USB 2.0 Startech USB Extender Power Adapter USB-A USB-A USB-C In-box

APC Back-UPS USB USB APC Back-UPS RS USB USB APC Back-UPS LS USB USB APC Back-UPS ES/CyberFort 350 USB APC Back-UPS BF500 USB APC BACK-UPS XS LCD USB APC Smart-UPS USB USB APC Back-UPS 940-0095A/C cables APC Back-UPS 940-0020B/C cables APC Back-UPS 940-0023A cable APC Back-UPS Office 940-0119A cable APC Ba

1. Connect the USB micro-B end of the cable to the USB micro-B port on Expansion Desktop. 2. Connect the USB-A end of the cable to your computer's USB-A port. Back up files You can connect your Seagate device to a USB-C port on your computer. The USB-C port must support USB 3.0 or higher. A USB micro-B to USB-C cable is not included with .

N450 WiFi Cable Modem Router (N450) 54 N600 WiFi Cable Modem Router (C3700) 55 AC1750 WiFi Cable Modem Router (C6300) 56 WiFi USB Adapters. AC1200 High Gain WiFi USB Adapter (AC1200) 58 AC600 WiFi USB Mini Adapter (A6100) 59 N600 WiFi USB Adapter (WNDA3100) 59 N300 WiFi USB Adapter (WNA3100) 60 N300 WiFi USB Mini Adapter (WNA3100M) 60 N150 WiFi USB Adapter (WNA1100) 61 N150 WiFi USB Micro .

ISDN Test and Measurement Equipment www.innoventif.de. Content . ISDN Cable Analogue Cable USB Cable Software CD EyeSDN USB-S0 1 1 0 1 1 EyeSDN USB-4S 1 4 Y-adapters 0 1 1 EyeSDN USB-4SBx 1 4 0 1 1 EyeSDN USB-E1 1 1 0 1 1 EyeSDN USB-A2 1 0 2 1 1 EyeSDN USB-A8/ EyeSDN USB-A8Bx 1 0 4 Y-cables 1 1

5 Connect the necessary cables Raccordez les câbles nécessaires Conecte los cables necesarios For USB connection, connect the USB cable Pour la connexion USB, raccordez le câble USB Para la conexión USB, conecte el cable USB For Ethernet connection, connect the ethernet cable Pour la connexion Ethernet, raccordez le câble Ethernet

4. USB 2.0 connector Connect USB-compatible devices, such as a USB keyboard, USB mouse, USB storage device, or USB printer. 5. USB 3.2 connector Gen 1 Connect USB-compatible devices, such as a USB keyboard, USB mouse,

USB-COMi-TB . USB-COMi-TB USB to Industrial Single RS-422 / 485 Adapter Manual . The USB-COMi-TB USB-to-Industrial Single RS-422/485 Adapter is designed to make industrial communication port expansion quick and simple. Connecting to a USB port on your computer or USB hub, the USB-COMi-TB instantly adds an industrial communication port to your .