Single And Dual Quad Gen Purpose, Low V, Low Pwr, Rail-to .

2y ago
33 Views
2 Downloads
1.17 MB
22 Pages
Last View : 17d ago
Last Download : 2m ago
Upload by : Ophelia Arruda
Transcription

LPV321,LPV324,LPV358LPV321 Single/LPV358 Dual/LPV324 Quad General Purpose, Low Voltage, LowPower, Rail-to-Rail Output Operational AmplifiersLiterature Number: SNOS413C

LPV321 Single/LPV358 Dual/LPV324 QuadGeneral Purpose, Low Voltage, Low Power, Rail-to-RailOutput Operational AmplifiersGeneral DescriptionFeaturesThe LPV321/358/324 are low power (9 µA per channel at5.0V) versions of the LMV321/358/324 op amps. This isanother addition to the LMV321/358/324 family of commodity op amps.The LPV321/358/324 are the most cost effective solutionsfor the applications where low voltage, low power operation,space saving and low price are needed. The LPV321/358/324 have rail-to-rail output swing capability and the inputcommon-mode voltage range includes ground. They all exhibit excellent speed-power ratio, achieving 5 kHz of bandwidth with a supply current of only 9 µA.The LPV321 is available in space saving 5-Pin SC70, whichis approximately half the size of 5-Pin SOT23. The smallpackage saves space on PC boards, and enables the designof small portable electronic devices. It also allows the designer to place the device closer to the signal source toreduce noise pickup and increase signal integrity.The chips are built with National’s advanced submicronsilicon-gate BiCMOS process. The LPV321/358/324 havebipolar input and output stages for improved noise performance and higher output current drive.(For V 5V and V 0V, typical unless otherwise noted)j Guaranteed 2.7V and 5V performancej No crossover distortionj Space saving packagej Industrial temperaturerange5-Pin SC702.0x2.1x1.0 mm 40 C to 85 Cj Gain-bandwidth product152 kHzj Low supply currentLPV3219 µALPV35815 µALPV32428 µAj Rail-to-rail output swingV 3.5 mV@ 100 kΩ LoadV 90 mV 0.2V to V 0.8Vj VCMApplicationsn Active filtersn General purpose low voltage applicationsn General purpose portable devicesConnection Diagrams5-PinSC70/SOT238-Pin SOIC/MSOP1009200114-Pin SOIC/TSSOP10092002Top ViewTop View10092003Top View 2006 National Semiconductor CorporationDS100920www.national.comLPV321 Single/LPV358 Dual/LPV324 Quad General Purpose, Low Voltage, Low Power, Rail-to-RailOutput Operational AmplifiersOctober 2006

LPV321 Single/LPV358 Dual/LPV324 QuadAbsolute Maximum Ratings (Note 1)Infrared or Convection (20 sec)Storage Temperature RangeIf Military/Aerospace specified devices are required,please contact the National Semiconductor Sales Office/Distributors for availability and specifications. 65 C to 150 CJunction Temp. (TJ, max) (Note 5)ESD Tolerance (Note 2)150 COperating Ratings (Note 1)Human Body ModelLPV3242000VSupply VoltageLPV3581500VTemperature Range1500VThermal Resistance (θJA)(Note 10)LPV321Machine Model100V Supply VoltageDifferential Input Voltage 235 C Supply Voltage (V –V )5.5V2.7V to 5V 40 C to 85 C5-Pin SC70478 C/W5-Pin SOT23265 C/W8-Pin SOIC190 C/W235 C/WOutput Short Circuit to V (Note 3)8-Pin MSOPOutput Short Circuit to V (Note 4)14-Pin SOIC145 C/W14-Pin TSSOP155 C/WSoldering Information2.7V DC Electrical CharacteristicsUnless otherwise specified, all limits guaranteed for TJ 25 C, V 2.7V, V 0V, VCM 1.0V, VO V /2 and RSymbolParameterVOSInput Offset VoltageTCVOSInput Offset Voltage AverageDriftConditionsMin(Note 7)L 1 MΩ.Typ(Note 6)Max(Note 7)Units1.27mV2µV/ CIBInput Bias Current1.750nAIOSInput Offset Current0.640nACMRRCommon Mode Rejection Ratio0V VCM 1.7V5070dBPSRRPower Supply Rejection Ratio2.7V V 5VVO 1V, VCM 1V5065dBVCMInput Common-Mode VoltageRangeFor CMRR 50 dB0 0.2Output SwingRL 100 kΩ to 1.35VVOISSupply Current1.9V 100V1.7V 3mV80180mVLPV32148µALPV358Both Amplifiers816µALPV324All Four Amplifiers1624µA2.7V AC Electrical CharacteristicsUnless otherwise specified, all limits guaranteed for TJ 25 C, V 2.7V, V 0V, VCM 1.0V, VO V /2 and RSymbolParameterGBWPGain-Bandwidth ProductConditionsCL 22 pFMin(Note 7)Typ(Note 6)LMax(Note 7) 1 MΩ.Units112kHzΦmPhase Margin97DegGmGain Margin35dBenInput-Referred Voltage Noisef 1 kHz178inInput-Referred Current Noisef 1 kHz0.50www.national.com2

Unless otherwise specified, all limits guaranteed for TJ 25 C, V 5V, V 0V, VCM 2.0V, VO V /2 and RBoldface limits apply at the temperature extremes.SymbolParameterConditionsMin(Note 7)L 1 MΩ.Typ(Note 6)Max(Note 7)1.5710UnitsVOSInput Offset VoltageTCVOSInput Offset Voltage AverageDrift2IBInput Bias Current25060nAIOSInput Offset Current0.64050nACMRRCommon Mode Rejection Ratio0V VCM 4V5071dBPSRRPower Supply Rejection Ratio2.7V V 5VVO 1V, VCM 1V5065dBVCMInput Common-Mode VoltageRangeFor CMRR 50 dB0 0.2AVLarge Signal Voltage Gain(Note 8)RL 100 kΩVOOutput SwingRL 100 kΩ to 2.5V4.21510100V 100V 200V 3.590IOISOutput Short Circuit CurrentSourcingLPV324, LPV358, and LPV321VO 0V216Output Short Circuit CurrentSinkingLPV321VO 5V2060LPV324 and LPV358VO 5V1116Supply CurrentmVµV/ CV4V/mVmV180220mAmAmALPV32191215µALPV358Both amplifiers152024µALPV324All four amplifiers284246µA5V AC Electrical CharacteristicsUnless otherwise specified, all limits guaranteed for TJ 25 C, V 5V, V 0V, VCM 2.0V, VO V /2 and RBoldface limits apply at the temperature extremes.SymbolParameterConditionsMin(Note 7)Typ(Note 6)L 1MΩ.Min(Note 7)UnitsSRSlew Rate(Note 9)0.1GBWPGain-Bandwidth ProductCL 22 pF152kHzΦmPhase Margin87DegGmGain Margin19dBenInput-Referred Voltage Noisef 1 kHz,146inInput-Referred Current Noisef 1 kHz0.303V/µswww.national.comLPV321 Single/LPV358 Dual/LPV324 Quad5V DC Electrical Characteristics

LPV321 Single/LPV358 Dual/LPV324 Quad5V AC Electrical Characteristics(Continued)Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device isintended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics.Note 2: Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC)Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC).Note 3: Shorting output to V will adversely affect reliability.Note 4: Shorting output to V will adversely affect reliability.Note 5: The maximum power dissipation is a function of TJ(MAX), θJA. The maximum allowable power dissipation at any ambient temperature isPD (TJ(MAX) – TA)/ θJA. All numbers apply for packages soldered directly onto a PC Board.Note 6: Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and willalso depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material.Note 7: All limits are guaranteed by testing or statistical analysis.Note 8: RL is connected to V -. The output voltage is 0.5V VO 4.5V.Note 9: Connected as voltage follower with 3V step input. Number specified is the slower of the positive and negative slew rates.Note 10: All numbers are typical, and apply for packages soldered directly onto a PC board in still air.Ordering InformationTemperature RangePackageIndustrialPackaging MarkingTransport MediaLPV321M7A191k Units Tape and ReelLPV321M7XA193k Units Tape and ReelNSC Drawing 40 C to 85 C5-Pin SC705-Pin SOT238-Pin SOIC8-Pin MSOP14-Pin SOIC14-Pin TSSOPwww.national.comLPV321M5A27A1k Units Tape and ReelLPV321M5XA27A3k Units Tape and ReelLPV358MLPV358MRailsLPV358MXLPV358M2.5k Units Tape and ReelLPV358MMP3581k Units Tape and ReelLPV358MMXP3583.5k Units Tape and ReelLPV324MLPV324MRailsLPV324MXLPV324M2.5k Units Tape and ReelLPV324MTLPV324MTRailsLPV324MTXLPV324MT2.5k Units Tape and Reel4MAA05AMF05AM08AMUA08AM14AMTC14

Unless otherwise specified, VS 5V, single supply,Supply Current vs. Supply Voltage (LPV321)Input Current vs. Temperature100920B5100920B4Sourcing Current vs. Output VoltageSourcing Current vs. Output Voltage1009204110092042Sinking Current vs. Output VoltageSinking Current vs. Output Voltage10092043100920445www.national.comLPV321 Single/LPV358 Dual/LPV324 QuadTypical Performance CharacteristicsTA 25 C.

LPV321 Single/LPV358 Dual/LPV324 QuadTypical Performance Characteristics Unless otherwise specified, VS 5V, single supply,TA 25 C. (Continued)Input Voltage Noise vs.FrequencyOutput Voltage Swing vs. Supply Voltage10092056100920B6Input Current Noise vsFrequencyInput Current Noise vs Frequency1009206810092070Crosstalk Rejection vs. FrequencyPSRR vs. Frequency10092073www.national.com100920726

CMRR vs. FrequencyCMRR vs. Input Common Mode Voltage1009206410092063 VOS vs. VCMCMRR vs. Input Common Mode Voltage1009206510092045 VOS vs. VCMInput Voltage vs. Output Voltage10092069100920467www.national.comLPV321 Single/LPV358 Dual/LPV324 QuadTypical Performance Characteristics Unless otherwise specified, VS 5V, single supply,TA 25 C. (Continued)

LPV321 Single/LPV358 Dual/LPV324 QuadTypical Performance Characteristics Unless otherwise specified, VS 5V, single supply,TA 25 C. (Continued)Input Voltage vs. Output VoltageOpen Loop Frequency Response1009207110092052Open Loop Frequency ResponseGain and Phase vs. Capacitive Load1009205110092054Gain and Phase vs. Capacitive LoadSlew Rate vs. Supply Voltage10092053www.national.com100920558

Non-Inverting Large Signal Pulse ResponseNon-Inverting Small Signal Pulse Response1009205010092049Inverting Large Signal Pulse ResponseInverting Small Signal Pulse Response1009204710092048Stability vs. Capacitive LoadStability vs. Capacitive Load10092061100920609www.national.comLPV321 Single/LPV358 Dual/LPV324 QuadTypical Performance Characteristics Unless otherwise specified, VS 5V, single supply,TA 25 C. (Continued)

LPV321 Single/LPV358 Dual/LPV324 QuadTypical Performance Characteristics Unless otherwise specified, VS 5V, single supply,TA 25 C. (Continued)Stability vs. Capacitive LoadStability vs. Capacitive Load1009205910092058THD vs. FrequencyOpen Loop Output Impedance vs Frequency1009207410092062Short Circuit Current vs. Temperature (Sinking)Short Circuit Current vs. Temperature (Sourcing)100920B8100920B7www.national.com10

BENEFITS OF THE LPV321/358/324SizeThe small footprints of the LPV321/358/324 packages savespace on printed circuit boards, and enable the design ofsmaller electronic products, such as cellular phones, pagers,or other portable systems. The low profile of the LPV321/358/324 make them possible to use in PCMCIA type IIIcards.10092004FIGURE 1. Indirectly Driving A Capacitive Load UsingResistive IsolationSignal IntegritySignals can pick up noise between the signal source and theamplifier. By using a physically smaller amplifier package,the LPV321/358/324 can be placed closer to the signalsource, reducing noise pickup and increasing signal integrity.In Figure 1, the isolation resistor RISO and the load capacitorCL form a pole to increase stability by adding more phasemargin to the overall system. The desired performance depends on the value of RISO. The bigger the RISO resistorvalue, the more stable VOUT will be. Figure 2 is an outputwaveform of Figure 1 using 100 kΩ for RISO and 1000 pF forC L.Simplified Board LayoutThese products help you to avoid using long pc traces inyour pc board layout. This means that no additional components, such as capacitors and resistors, are needed to filterout the unwanted signals due to the interference betweenthe long pc traces.Low Supply CurrentThese devices will help you to maximize battery life. Theyare ideal for battery powered systems.Low Supply VoltageNational provides guaranteed performance at 2.7V and 5V.These guarantees ensure operation throughout the batterylifetime.Rail-to-Rail OutputRail-to-rail output swing provides maximum possible dynamic range at the output. This is particularly importantwhen operating on low supply voltages.10092075FIGURE 2. Pulse Response of the LPV324 Circuit inFigure 1Input Includes GroundAllows direct sensing near GND in single supply operation.The differential input voltage may be larger than V withoutdamaging the device. Protection should be provided to prevent the input voltages from going negative more than 0.3V(at 25 C). An input clamp diode with a resistor to the IC inputterminal can be used.The circuit in Figure 3 is an improvement to the one in Figure1 because it provides DC accuracy as well as AC stability. Ifthere were a load resistor in Figure 1, the output would bevoltage divided by RISO and the load resistor. Instead, inFigure 3, RF provides the DC accuracy by using feedforward techniques to connect VIN to RL. Caution is neededin choosing the value of RF due to the input bias current ofthe LPV321/358/324. CF and RISO serve to counteract theloss of phase margin by feeding the high frequency component of the output signal back to the amplifier’s invertinginput, thereby preserving phase margin in the overall feedback loop. Increased capacitive drive is possible by increasing the value of CF. This in turn will slow down the pulseresponse.CAPACITIVE LOAD TOLERANCEThe LPV321/358/324 can directly drive 200 pF in unity-gainwithout oscillation. The unity-gain follower is the most sensitive configuration to capacitive loading. Direct capacitiveloading reduces the phase margin of amplifiers. The combination of the amplifier’s output impedance and the capacitiveload induces phase lag. This results in either an underdamped pulse response or oscillation. To drive a heaviercapacitive load, circuit in Figure 1 can be used.11www.national.comLPV321 Single/LPV358 Dual/LPV324 QuadApplication Information

LPV321 Single/LPV358 Dual/LPV324 QuadApplication Information(Continued)1009200710092005FIGURE 3. Indirectly Driving A Capacitive Load withDC AccuracyINPUT BIAS CURRENT CANCELLATIONThe LPV321/358/324 family has a bipolar input stage. Thetypical input bias current of LPV321/358/324 is 1.5 nA with5V supply. Thus a 100 kΩ input resistor will cause 0.15 mVof error voltage. By balancing the resistor values at bothinverting and non-inverting inputs, the error caused by theamplifier’s input bias current will be reduced. The circuit inFigure 4 shows how to cancel the error caused by input biascurrent.FIGURE 5. Difference AmplifierInstrumentation CircuitsThe input impedance of the previous difference amplifier isset by the resistor R1, R2, R3, and R4. To eliminate theproblems of low input impedance, one way is to use avoltage follower ahead of each input as shown in the following two instrumentation amplifiers.Three-op-amp Instrumentation AmplifierThe quad LPV324 can be used to build a three-op-ampinstrumentation amplifier as shown in Figure 610092006FIGURE 4. Cancelling the Error Caused by Input BiasCurrentTYPICAL SINGLE-SUPPLY APPLICATION CIRCUITSDifference AmplifierThe difference amplifier allows the subtraction of two voltages or, as a special case, the cancellation of a signalcommon to two inputs. It is useful as a computational amplifier, in making a differential to single-ended conversion or inrejecting a common mode signal.www.national.com10092085FIGURE 6. Three-op-amp Instrumentation AmplifierThe first stage of this instrumentation amplifier is adifferential-input, differential-output amplifier, with two voltage followers. These two voltage followers assure that theinput impedance is over 100 MΩ. The gain of this instrumentation amplifier is set by the ratio of R2/R1. R3 should equalR1 and R4 equal R2. Matching of R3 to R1 and R4 to R2affects the CMRR. For good CMRR over temperature, lowdrift resistors should be used. Making R4 Slightly smallerthan R 2 and adding a trim pot equal to twice the differencebetween R 2 and R4 will allow the CMRR to be adjusted foroptimum.12

ACTIVE FILTER(Continued)Two-op-amp Instrumentation AmplifierSimple Low-Pass Active FilterA two-op-amp instrumentation amplifier can also be used tomake a high-input-impedance DC differential amplifier (Figure 7). As in the three-op-amp circuit, this instrumentationamplifier requires precise resistor matching for good CMRR.R4 should equal to R1 and R3 should equal R2.The simple low-pass filter is shown in Figure 9. Its lowfrequency gain(ω o) is defined by R3/R1. This allowslow-frequency gains other than unity to be obtained. Thefilter has a 20 dB/decade roll-off after its corner frequencyfc. R2 should be chosen equal to the parallel combination ofR1 and R3 to minimize errors due to bais current. Thefrequency response of the filter is shown in Figure 101009201110092014FIGURE 7. Two-op-amp Instrumentation AmplifierSingle-Supply Inverting AmplifierThere may be cases where the input signal going into theamplifier is negative. Because the amplifier is operating insingle supply voltage, a voltage divider using R3 and R4 isimplemented to bias the amplifier so the input signal is withinthe input common-common voltage range of the amplifier.The capacitor C1 is placed between the inverting input andresistor R1 to block the DC signal going into the AC signalsource, VIN. The values of R1 and C1 affect the cutoff frequency, fc 1/2π R 1C1.As a result, the output signal is centered around mid-supply(if the voltage divider provides V /2 at the non-invertinginput). The output can swing to both rails, maximizing thesignal-to-noise ratio in a low voltage system.FIGURE 9. Simple Low-Pass Active Filter10092015FIGURE 10. Frequency Response of Simple Low-passActive Filter in Figure 9Note that the single-op-amp active filters are used in to theapplications that require low quality factor, Q ( 10), lowfrequency ( 5 kHz), and low gain ( 10), or a small value forthe product of gain times Q ( 100). The op amp should havean open loop voltage gain at the highest frequency of interest at least 50 times larger than the gain of the filter at thisfrequency. In addition, the selected op amp should have aslew rate that meets the following requirement:Slew Rate 0.5 x (ωHV OPP) X 10 6V/µsecWhere ωH is the highest frequency of interest, and VOPP isthe output peak-to-peak voltage.10092013FIGURE 8. Single-Supply Inverting Amplifier13www.national.comLPV321 Single/LPV358 Dual/LPV324 QuadApplication Information

LPV321 Single/LPV358 Dual/LPV324 QuadSC70-5 Tape and Reel Specification100920B3SOT-23-5 Tape and Reel SpecificationTAPE FORMATwww.national.comTape Section# CavitiesCavity StatusCover Tape StatusLeader0 (min)EmptySealed(Start End)75 aledTrailer125 (min)EmptySealed(Hub End)0 (min)EmptySealed14

LPV321 Single/LPV358 Dual/LPV324 QuadSOT-23-5 Tape and Reel Specification(Continued)TAPE DIMENSIONS100920B18 mmTape Size0.1300.1240.1300.1260.138 0.0020.055 0.0040.1570.315 0.012(3.3)(3.15)(3.3)(3.2)(3.5 0.05)(1.4 0.11)(4)(8 0.3)DIM ADIM AoDIM BDIM BoDIM FDIM KoDIM P1DIM W15www.national.com

LPV321 Single/LPV358 Dual/LPV324 QuadSOT-23-5 Tape and Reel Specification(Continued)REEL DIMENSIONS100920B28 mmTape Sizewww.national.com7.000.059 0.512 0.795 2.165330.001.50AB13.00 20.20 55.00CDN160.331 0.059/ 0.0000.567W1 0.078/ 0.0398.40 1.50/ 0.0014.40W1 2.00/ 1.00W1W2W3

LPV321 Single/LPV358 Dual/LPV324 QuadPhysical DimensionsPhysical Dimensionsinches (millimeters) unless otherwise noted5-Pin SC70NS Package Number MAA05A5-Pin SOT23NS Package Number MF05A17www.national.com

LPV321 Single/LPV358 Dual/LPV324 QuadPhysical Dimensionsinches (millimeters) unless otherwise noted (Continued)8-Pin SOICNS Package Number M08A8-Pin MSOPNS Package Number MUA08Awww.national.com18

LPV321 Single/LPV358 Dual/LPV324 QuadPhysical Dimensionsinches (millimeters) unless otherwise noted (Continued)14-Pin SOICNS Package Number M14A14-Pin TSSOPNS Package Number MTC1419www.national.com

LPV321 Single/LPV358 Dual/LPV324 Quad General Purpose, Low Voltage, Low Power, Rail-to-RailOutput Operational AmplifiersNotesNational does not assume any responsibility for use of any circuitry described, no circuit patent licenses are

LPV321 Single/LPV358 Dual/LPV324 Quad General Purpose, Low Voltage, Low Power, Rail-to-Rail Output Operational Amplifiers General Description The LPV321/358/324 are low power (9 µA per channel at 5.0V) versions of the LMV321/358/324 op amps. This is another add

Related Documents:

2015 suzuki king quad (lt-a400asi) tr 2016 suzuki king quad (lt-a400asi) tr 2017 suzuki king quad (lt-a400fsi) tr 2004 suzuki quad sport (lt-z400) tr 2005 suzuki quad sport (lt-z400) nt 2006 suzuki quad sport (lt-z400) nt 2007 suzuki quad sport (lt-z400) nt 2008 suzuki quad sport (lt-z400) nt 2009 suzuki quad

Single, Dual, Quad Low-Voltage, Rail-to-Rail Operational Amplifiers LMV321, NCV321, LMV358, LMV324 The LMV321, LMV321I, NCV321, LMV358/LMV358I and LMV324 are CMOS single, dual, and quad low voltage operational amplifiers with rail to rail output swing. These amplifiers are a cost effective solution for

Single/Dual/Quad, Low Offset, Low Noise, RRO Operational Amplifiers General Description The LMV771/LMV772/LMV774 are Single, Dual, and Quad low noise precision operational amplifiers intended for use in a wide range of applications. Other important characteristics of

Gen 3, 6.5 kV Gen 3, 900 V Gen 2, C2M Family 1.2 kV Gen 1, 1.2 kV Gen 3, 1.2 kV Scaling of State-of-Art Gen-3 SiC Power MOSFETs in R&D RCh/RON becomes larger for lower-V MOSFETs. For Gen-3 1200V MOSFET, RCh 40% of total RON. Future Prospective Reduce RCh/RON by: o Improving MOS INV o Higher packing density

gen-26 davar nanabhoy s practical book keeping & accountancy 12 07/07/1966 gen-27 ghatalia s v practical auditing 15 07/07/1966 gen-28 gupta rup ram advanced accounting 22.5 07/07/1966 gen-29 gupta rup ram auditing 12.5 07/07/1966 gen-30 gupta rup ram text book of auditing 7.5 07/07/1966 gen-31 gupta rup ram cost accounting 9 07/0

SPARC @ Oracle 16 x 2nd Gen cores 6MB L2 Cache 1.7 GHz 8 x 3 rd Gen Cores 4MB L3 Cache 3.0 GHz 16 x 3rd Gen Cores 8MB L3 Cache 3.6 GHz 12 x 3rd Gen 48MB L3 Cache 3.6 GHz 6 x 3 Gen Cores 48MB L3 Cache 3.6 GHz T3 T4 T5 M5 M6 S7 32 x 4th Gen Cores 64MB L3 Cache 4.1 GHz DAX1 M7 8 x 4th Gen Co

QUAD-DECK TYPICAL DETAIL DRAWINGS QD-100 Series QUAD-DECK PRODUCT DETAILS AND COMMON SPECIFICATIONS INDEX QD-200 Series QUAD-DECK TO QUAD-LOCK WALL DETAILS QD-300 Series QUAD-DECK

SUZUKI SUZUKI Years Hybrid SYSTEM #105590 SUZUKI 250 2x4 ‘97-01 N/D SUZUKI 280 King Quad ‘98 & Older N/D SUZUKI 300 King Quad ‘99-01 N/D SUZUKI 400 Eiger 2x4, 4x4 ‘02-07 N/D SUZUKI 400 King Quad 4x4/AS/AF/ASi/AFi ‘08-18 Yes SUZUKI 450 King Quad 4x4/AXi ‘07-10 Yes SUZUKI 500 King Quad AXI ‘09-18 Yes SUZ