OWNER S MANUAL - FX Luminaire
LUXOR OWNER’S MANUALLUXORLED Landscape Lighting ControllerOwner’s Manual and Installation Instructionsfor Luxor Lighting Controller
Table of Contents3344Luxor OverviewLuxor ComponentsGlossary of TermsSafety Information55558Installing the Luxor TransformerStep 1: Locating the TransformerStep 2: Mounting TransformersStep 2: ContinuedStep 3: Running Cable to theFixturesLow-Voltage CableCabling MethodsConnecting Cables at the TerminalBlock1010101111111212132Operating the Luxor ControllerNavigating the LuxorHome ScreenActivity ScreenDiagnostics ScreenSetup ing Light Fixtures intoGroupsSetting Up ProgramsCalendar-Based ProgrammingThemesManual ModeColorColor PaletteColor WheelMixing FX Luminaire LED,ZD Technology , and ZDCTechnology Using Other Devices with the LuxorDisable26 Luxor Linking Setup26 Updating to Luxor Linking27 Connecting Satellite Controllers28 Chassis Communication andAssignment29 Care and Maintenance29 Regular Preventive Maintenance30 Troubleshooting31Firmware Updates33 Fuse Replacement34 System Reset34 Facepack Reset35 Database Reset35 Chassis Indicator Lights36 Warranty
Luxor OverviewLuxor is a lighting transformer and controller capable ofcontrolling groups of lights that are initiated by programmedevents. These events are adjustments of light intensity at settimes. All lights within a system are communicated with andpowered via two-wire connections. All lights within a systemcommunicate with the same two-wire connections that alsopower the system.Luxor ComponentsNoteLuxor is intended for use with FX Luminaire LEDfixtures or devices containing FX Luminaire ZD Technology or ZDC Technology . Use of otherfixtures is not recommended due to the absence ofcommunication capabilities. Luxor is not for use withincandescent fixtures.Core CoverChassisFacepackFacepack ConnectionLUXORLCD ScreenChassis LEDClickable Scroll WheelTerminal BlocksHome ButtonFuse CoverBack ButtonFixture Assignment PortsFigure 1: Luxor ControllerFigure 2: Luxor Facepack3
Luxor OverviewGlossary of TermsSafety InformationGroup: An addressed set of lights that is designated numericallyand controlled as a set by the controllerThese cord-connected units consist of step-down, isolated,two-winding-type transformers, circuit breakers, and associatedcircuitry intended to supply power to low-voltage, submersiblelighting fixtures.Theme: A predetermined set of groups, intensities, and colorscalled to action by the program or manual functionsFixture/Luminaire: Light unit that contains an FX LuminaireLED board or device with FX Luminaire zoning, dimming, orcolor capabilitiesIntensity: Value indicating the measurable amount of brightness,from 1% to 100%Event: The initiation, adjustment, or conclusion of a selectedtheme or group with specific intensity and/or color settingsDuration: The length of time an event will runHue: The primary attribute of a color; it is represented bynumeric values between 0 and 359Saturation: The richness of a color mixed with white light,from 0% to 100%Color: The visual combination of hue and saturationPrimary Controller: Luxor controller containing a facepackSatellite Controller: Controller without a facepackWARNING — Risk of Electric Shock. Install power unit 5' (1.5 m)or more from a pool or spa and 10' (3 m) or more from a fountain.Where the power unit is installed within 10' (3 m) of a pool or spa,connect power unit to a GFCI-protected branch circuit. Do notuse an extension cord when connecting the power unit to the120-volt source. The grounding conductor shall be 12 AWG (2.05mm) minimum. Outdoor power unit shall be connected to a GFCIprotected, hooded, flush-type cover plate receptacle marked“Wet Location” while in use.Caution: The supply circuit for the landscape lighting systemshall be protected by a Class A–type ground fault circuitinterrupter, unless it is provided with the landscape lightingsystem. This device is accepted as a component of a landscapelighting system where the suitability of the combination shall bedetermined by local inspection authorities having jurisdiction. Donot connect two or more power supplies in parallel. Not for use indwelling units. This presents a risk of fire. Do not place insulationunder terminal plate. Check connector after installation.Circuit Protection 411 amps for 150-watt power controller22 amps for 300-watt power controller
Installing the Luxor TransformerStep 1: Locating the Transformer1.Locate transformer(s) in a well-ventilated area awayfrom direct irrigation spray and central to the proposedinstallation site of the majority of the lighting fixtures. Theprimary goal is to minimize the length of cable runs fromyour transformer to the lighting fixtures, which minimizesvoltage drop and cable size. A common mistake is to locatethe single transformer on the service side of the house orin the garage, which might result in excessively long cableruns to reach lighted areas. Transformer(s) with power cordsmust be located adjacent to a 120-volt, GFCI-protectedexterior electrical receptacle. If a 120-volt power source isnot available at the desired transformer installation location,it is advised that you hire a licensed electrician to run adedicated 120-volt, 15-amp circuit to the desired location.For the international/export Luxor version, the previouslymentioned information applies for 230-volt, 10-amp circuits.2. Test all existing receptacles with both a receptacle tester anda digital voltmeter or amp clamp to verify proper wiring andvoltage at the receptacle.Step 2: Mounting Transformerstransformer on the screw.3. Use a level and a pencil to determine and mark locations forthe bottom anchors. Remove transformer from wall. Drillbottom anchor holes and install anchors.4. Place transformer back on top of the uppermost mountingscrew and install screws into anchors at bottom of thetransformer to secure it to the wall.Step 2: ContinuedPost-Mount Installation5. Install pressure-treated 4" x 4" x 36" (10 cm x 10 cm x 92 cm)minimum post in concrete footing.6. Repeat wall-mount installation instructions (Figure 3on page 5), without the use of wall anchors.For additional information regarding installation techniques, visitfxl.com and click on the Professionals tab.All Luxor controllers come equipped with a 5' (1.5 m), 12 AWG(2.05 mm), 3-prong electrical power cord. Only use the Luxorpower cord in conjunction with a GFCI-protected, 120-voltexterior receptacle (or 230-volt receptacle for international/export version).Wall-Mount Installation1.Install all transformers a minimum of 12" (30.5 cm) above thefinish grade, as measured from finish grade to the bottom ofthe transformer and according to code.2. Drill pilot holes into the mounting surface, insert anchors,and install screws into the anchors, leaving approximately1/8" (0.3 cm) of the thread exposed on the screw. Mount theNoteWhen installing the Luxor Wi-Fi module, considerincreasing the installation height to improve signalstrength and screen visibility.5
Installing the Luxor TransformerSide ViewFront ViewMounting brackets120 V power outlet12" (30.5 cm)minimumPower cord1½" (3.8 cm) conduitFigure 3: Luxor wall mounting6
Installing the Luxor TransformerSide ViewFront ViewMounting brackets1½" (3.8 cm) conduit12" (30.5 cm)minimum4" x 4" (10.2 cm- 10.2 cm) postConcrete footingFigure 4: Luxor post mounting7
Installing the Luxor TransformerStep 3: Running Cable to the FixturesOnce the transformer has been installed and determined allfixture locations, the next step is to run the correct size cablefrom the transformer to the fixtures. FX Luminaire LED fixturesrequire between 10 and 15 volts for optimal operation andlongevity. This is accomplished by the following:1.Grouping fixtures into distance zones as illustrated below. Donot have a fixture that is 10' (3 m) away from the transformeron the same cable run as one that is 100' (30 m) away.2. Use the proper cabling method for the application. Try tocenter-load all cable runs when possible to minimize thevoltage differential between fixtures.3. Use a correctly sized cable to accommodate voltage drop. Asa general rule of thumb, limit the wattage load per cable runto no more than 160 watts.CIRCUITING GUIDELINESLoads Per CableClose-Zone 0–40' (0 - 12.2 m)12 AWG (2.05 mm): 160 watts max.10 AWG (2.59 mm): 180 watts max.8 AWG (3.26 mm): 220 watts max.10 AWG (2.59 mm): 140 watts max.8 AWG (3.26 mm): 200 watts max.10 AWG (2.59 mm): 120 watts max.8 AWG (3.26 mm): 180 watts max.Mid-Zone 40–80' (12.2 m - 24.4 m)12 AWG (2.05 mm): 120 watts max.Far-Zone 80–120' (24.4 m - 36.6 m)12 AWG (2.05 mm): 100 watts max.Out There-Zone 120–160' (36.6 m - 54.9 m)12 AWG (2.05 mm): 60 watts max.810 AWG (2.59 mm): 100 watts max.8 AWG (3.26 mm): 160 watts max.
Installing the Luxor TransformerSummaryFor maximum light output and LED life, each luminaire should beprovided with 10 to 15 volts.Cable StatsLow-voltage lighting systems are typically installed usingdirect-burial-rated stranded cable. The most common cable usedis referred to as 12/2 AWG (2.05 mm) stranded cable. The sizeof cable used in wiring the lighting system will be determined bythe wattage load and length of cable run from the transformer tothe lighting fixtures.LUXORWatts shown are per 12 AWG (2.05 mm), cable. Installadditional cable runs as needed to complete project. Toincrease wattage maximum, run 8 AWG (3.26 mm) ordouble 12 AWG (2.05 mm), to the first fixture in the zone.Use a digital voltmeter to fine-tune circuits.Figure 5: Wiring example14-VoltCommonIt is very important to note that all low-voltage cable has amaximum rating. Overloading cable can create a dangeroussafety hazard, so be sure to choose the proper cable size foryour lighting system.Out There-Zone120–160'(36.6 m - 54.9 m)LED 110 watts max.14-volt tap9
Installing the Luxor TransformerLow-Voltage CableEach low-voltage lighting cable consists of two parts. One part ofthe cable is designated to carry the voltage load and is referredto as the Common lead. The Common lead is installed into one ofthe two COM terminal blocks. The other wire lead is installed intoone of the two lugs labeled 15V. Voltage is carried out from thetransformer to the fixtures via the Common side of the cable andreturns back to the transformer 15V tap via the other half of thecable, thus completing the circuit.Cabling MethodsWithin each cabling zone, you may utilize any of a number ofcabling methods. The primary objective is to minimize voltagedrop by installing the proper size feeder cable (home run) to eachzone, and to make sure each fixture on each cable run is receiving10 to 15 volts. Center feeding the “home run” (the main cable runfrom the transformer to the first fixture on the circuit) will helpminimize the voltage differential between the first fixture andthe last fixture on the cable run.Figure 6: Output terminal blocksConnecting Cables at the Terminal BlockTransformer terminal block: The Luxor controller includes twoCommon lugs, and two 15V lugs.Common Lugs: One conductor from each cable run coming fromthe lights to the transformer must be connected to one of thecommon lugs. The other conductor will be installed into the 15Vhot lug.Figure 7: Back of facepack showing SD card and reset button10
Operating the Luxor ControllerNavigating the LuxorThe Luxor contains only three user interface elements: Home button: opens main screen while on any other functionHelp button: navigates to previous screenClickable scroll wheel: primary interaction and selection toolHome ScreenAll functions on the Luxor are accessible through the Homescreen. The default display on the Home screen displaysthe following: All category options are located on the right side of the Homescreen and are selected using the main scroll wheel. Turn theblack scroll wheel clockwise or counterclockwise until the desiredcategory is highlighted in light blue. Press the scroll wheel inwardto select and enter the desired category. While in any screen, the Home button can be pressed toreturn to the Home screen.While in any screen, the Back button can be pressed to returnto the previous screen.Current timeCurrent dateSunrise/sunset for the current day (dependent on location,see Set Location)All category options are listedFigure 8: Home screenshot11
Operating the Luxor ControllerActivity ScreenDiagnostics ScreenAfter five minutes of inactivity, an Activity screen will appear onthe LCD screen if the lights are running. The wait time is reducedto only five seconds when the current screen is the Home screen.Assigned Controller assignedThe Activity screen displays: Chassis load: Amp load of controller chassis. Chassis 1-10 aredisplayed. Only chassis with an active load will display anorange load bar.Current timeSource of transformer load: Manual or ScheduleCommunicating Controller communicatingOverload Controller overload indicationLoad Status Controller load in percentNo selections can be made on this screen; it is simply an activitydisplay. Press the Home button to return to the Home screen.Figure 10: Diagnostics screenshotFigure 9: Activity screenshot12
Operating the Luxor ControllerSetup ScreenAll background tools and settings (except color) are accessible inthe Setup screen. Scroll through the various options to set up thecontroller.Time/Date Set the three time categories (Hr:Min:Sec) to the currenttime settings by pushing the scroll wheel when theappropriate field is highlighted, scrolling through the numericoptions, and pressing the scroll wheel again to finalize theselection.Turn past 12 on the hour (“Hr”) setting to adjust a.m. andp.m., as displayed next to the seconds (“Sec”).To convert clock to 24-hour convention, select the “24hr”selection box.Set the three date categories (Month, Day, Year) tothe current date by pushing the scroll wheel when theappropriate field is highlighted, scrolling through the options,and pressing the scroll wheel again to finalize the selection.Setting the month, day and year automatically sets the dayof the week which appears to the right of the year.Daylight Saving Time (DST), when activated, will adjust timeforward or backward by one hour at the appropriatedates each year. To initiate it, select On. To deactivate it,select Off.Select Auto to sync the Luxor time clock every 24 hours.Figure 11: Setup screenshot13
Operating the Luxor ControllerLanguageIn the Setup screen, select the language field by pressing thescroll wheel and turning it to the desired language. Press thescroll wheel again to finalize the selection. The coordinate settings are automatically saved after eachpress of the scroll wheel. Select the Home button to leave theLocation screen.Reset or adjustment is initiated by pressing the scroll wheeland then repeating the above latitude and longitude steps.The language change will not take effect until either the Backor the Home buttons are pressed.LocationThe Location menu is designed to graphically represent a Luxor’slocation on a map for accurate sunrise and sunset times based onthe current date, time zone, and longitude/latitude settings.First, select Location from the Setup screen. While in theLocation screen, select Region. Once region is selected, scroll toTime Zone and select the current time zone.If latitude and longitude coordinates are known, enter the valuesinto the Lat and Long fields. To set latitude and longitude usingthe map feature, scroll to Map and press the scroll wheel. 14The full-screen crosshairs designate the user’s locationon the map. The map will change based off of selectedregion.Latitude is first adjusted by rotating the scroll wheel to movethe crosshairs up and down. Numeric indicators atthe top right display the actual coordinate. Press thescroll wheel to select the latitude; it is set by pressing theclick-wheel.Longitude is next adjusted by rotating the scroll wheel tomove the crosshairs left and right.Figure 12: Location ScreenFigure 13: Location map of the United States
Operating the Luxor ControllerAssignWhen compatible fixtures are plugged in to the fixtureprogramming ports, the assign screen will automatically display.The Assign screen is also accessible under the Setup menu.NetworkBy default, the LAN tab will be displayed. The Wi-Fi or label willbe displayed when the FX Luminaire Wi-Fi module is insertedinto the accessory port in the back of the facepack. For moreinformation on using the Wi-Fi, refer to the separate owner’smanual for Luxor Accessories.RestrictThe restrict function prevents changes to themes.From the Home screen, navigate to the Setup and selectRestrict Themes screens using the scroll wheel.2. To remove the restriction, deselect Restrict Themes.1.15
Operating the Luxor ControllerBackupThe backup function saves all user input information, includingprograms, themes, colors, and setup data. To create a backup filefor your Luxor, follow the steps below.1.2.3.4.5.Insert an SD card into the side of the facepack with the pinsfacing toward the front of the facepack.From the Home screen, navigate to the Setup and thenBackup screens using the scroll wheel.Input a file name for the backup file. You do not need to useall available spaces.Press Backup.After backup is successful, press the SD card inward and thenrelease to remove the card from the facepack.Restore an existing file, follow steps below:1.2.3.4.5.16Insert an SD card (pins facing the front) with the pre-loadedfile into the side of the facepack. Press the card completelyinward and then release. The card will lock into place.From the Home screen, navigate to the Setup and thenBackup screens using the scroll wheel.Input the file name of the desired database to restore. Thefilename must match exactly.Press Restore.After a successful restore, press the SD card inward and thenrelease to remove the card from the facepack.
Operating the Luxor ControllerAssigning Light Fixtures into GroupsThe lighting assignment screen is automatically displayed whenan FX Luminaire LED fixture or device containing FX LuminaireZD Technology or ZDC Technology is connected into theassignment ports of the facepack. This mode can also be forcedby navigating to Setup and selecting Assign. Enter this mode by placing two separate wires from asingle FX Luminaire LED fixture or device containing FXLuminaire ZD Technology or ZDC Technology into each ofthe assignment ports on the front of the facepack. The wiresmust maintain contact inside the assignment ports duringthe entire process.Navigate to Program and press the scroll wheel toinitiate assignment. When complete, the screen willshow “Assignment Successful” or “Assignment Failed.”If failed, reposition wires and try again. If the problempersists, the board or device may either be defective or notprogrammable.The assigned group number is stored in the device and notin the facepack. Thus, power loss or other errors within theLuxor controller will not affect the fixture assignment. If adevice (e.g., LED board, lamp, Cube) is replaced, the newdevice must be programmed to the desired group number.Note Only one fixture can be addressed at a time.Attempting to address more than one fixtureat a time can result in assignment failures.Figure 14: Fixture assignment wire diagram17
Operating the Luxor ControllerSetting Up Programs The Programs screen is where all daily running programs areset up. Programs are set by calling up fixtures that have beenassigned to groups or themes. For more about assigning fixturesto groups, see “Assigning Light Fixtures into Groups.” 18Each program is designated by a letter (“A” through “G”) atthe top right section of the screen. Select the desired letterusing the scroll wheel prior to selecting the days of the week.Selecting days of the week designates which days theprogram will run based on the event settings. Select orremove each day by highlighting the corresponding box ove
Installing the Luxor Transformer Step 3: Running Cable to the Fixtures Once the transformer has been installed and determined all fixture locations, the next step is to run the correct size cable from the transformer to the fixtures. FX Luminaire LED fixtures require bet
2' x 2' suspended acoustical ceiling tile gypsum board ceiling or soffit 2' x 2' luminaire recessed can luminaire exposed ceiling with painted structure above 1' x 4' luminaire recessed 4" linear fixture projection screen by owner 2' x 4' luminaire recessed cove light s audio speakers "clima plus", astro wit
14. In case the lamp is delivered with the luminaire is the lamp in conformity with the requirements for CE marking and with the applicable legislation? (lamp is to be considered as a separate product). 15. In case of luminaire with earth connection (class I luminaire), are all metal part which are accessible in normal use, or when the luminaire is
er's Manual and the following Owner's Man‐ uals: Integrated Owner's Manual in the vehicle. Online Owner's Manual. MINI Motorer’s Guide App. Notes on updates can be found in the appendix of the printed Owner's Manual for the vehicle. Owner's Manual for Navigation, Entertainment, Communication Owner's Manual for Navigation, Entertainment,
The Philips EasyAir SNS200 is the ideal solution for per-luminaire control of new light luminaires. It combines . occupancy sensing, daylight harvesting and task tuning in a single, compact package for easy OEM luminaire assembly. EasyAir SNS200 operates with the established Philips Xitanium SR LED driver standard to make a simple two-
the Galleon LED luminaire allows scalability from 3,000 to over 53,000 delivered lumens. The 4000K/70 CRI is standard, with 6000K/70 CRI and 3000K/70 CRI options available. Long Life with Low Maintenance Costs In addition to delivering superior performance, the Galleon LED luminaire is de
Cove Light AC HO RGB Graze is a slim profile, AC line powered high brightness luminaire. The luminaire is controllable via DMX512 and perfect for alcove applications. The simplicity of the luminaire’s topology means it can be simply daisy-chained to form long runs. Cove Light
Crosstour MAXX Luminiares (Figures 5-6) 1. Installez le luminaire XTOR MAXX au mur selon les instructions du luminaire. 2. Installez les écussons autour du luminaire XTOR MAXX comme montré aux Figures. 5 et 6. 3. Utilisez les boulons d’ancrage (fourni par d’autres) pour fixer les éc
Appliances and range hood - Drimmers Major Appliances, New York, NY Light fixture - Flos, Luminaire Contract, Miami, FL Study/Guest Bedroom Bed, bed covering fabric and bedside table - B&B Italia SpA, Luminaire Contract, Miami, FL Sofa - Living Divani srl, Luminaire Contract,
