C A T A L O G - Mechanical Seals
UTEX INDUSTRIES, INC.Mechanical SealsCATACARTRIDGE SEALSMETAL BELLOWS CARTRIDGE SEALSHIGH PRESSURE PIPELINE SEALSCOMPOSITE CARTRIDGE SEALSROTARY UNITS METAL BELLOWS MULTI SPRING OUTSIDE MOUNTSTATIONARY SEATS O-RING BLOCK CLAMP “L” TYPEUTEX INDUSTRIES, INC.Taking Sealing Technology Beyond TomorrowISO 9001 CertifiedLOG
LIBERATOR I LIBERATOR I Technical DataMATERIALSMETAL PARTS316 SS metal parts are standard.STATIONARY FACECNFJ-B grade carbon is standard. TungstenCarbide and Silicon Carbide are available.ROTATING SEAL FACEAlpha sintered Silicon Carbide.O-RINGSAflas is standard. EPDM, Neoprene, Nitrile,Chemraz, Kalrez, and Viton are available.TEMPERATURE-60 F TO 400 F-50 C TO 204 CPRESSURE400 psi27 barSPEED5000 fpm125 m/sThe Liberator I cartridge seal (patented) incorporates advanced sealdesign features. Using a “ball” drive, the Liberator resists twisting andtorsional strains common to pin or key drives. The thin cross-sectionallows the Liberator I to be used in ANSI pumps without modifications.It employs a multi-crested wave spring which is a non-cloggingspring isolated from the product for optimum corrosion resistance.Standard face materials are carbon vs. silicon carbide which togetherprovide the highest PV rating of any face material combination. Therotating seat and spring loaded stationary accept higher shaft speeds,heavier viscosity fluids, and greater misalignment.Aflas o-rings are standard in all Liberators giving them a broadrange of chemical compatibility. The Liberator gland incorporates bothvent and drain connections, a carbon throttle bushing, and provides twotangential flush ports for clockwise or counterclockwise pump rotation.
SHAFTSIZEINCH MMA1.000 251.125 281.250 30321.375 33351.500 381.562 401.6251.750 451.875 482.000 502.1252.187 552.2502.375 602.5002.625 652.750 00STUFFINGBOX BOREMIN.MAX.B1.625 41.51.750 44.51.875 48.01.875 48.02.000 51.02.000 51.02.250 57.52.312 59.02.3752.500 63.52.625 67.02.750 70.02.8752.937 75.03.0003.125 79.53.2503.375 86.03.750 .000SEALO.D.C1.875 48.02.000 51.02.125 54.02.125 54.02.250 58.02.250 58.02.500 64.02.562 66.02.6252.750 70.02.875 73.03.000 77.03.1253.187 81.03.2503.375 86.03.5003.625 93.04.250 108.04.500 3.8754.500 3.8754.750 4.1254.750 4.1255.000 4.3755.000 4.3755.250 4.6255.250 4.6255.500 4.8755.500 4.8751.565 39.81.690 42.91.815 46.11.815 46.11.940 49.31.940 49.32.187 55.62.250 57.22.3122.437 61.92.562 65.12.687 68.32.8122.875 73.02.9373.062 77.83.1873.312 84.13.625 .000STUFFINGBOX HGLANDO.D.SLOTWIDTHGHJ0.812 210.812 210.812 210.812 210.750 190.750 190.937 240.937 240.9370.937 240.937 240.937 240.9370.937 240.9370.937 240.9370.937 241.000 25.731.731.731.731.731.731.731.731.731.731.721 18.3.721 18.3.721 18.3.721 18.3.656 16.7.656 16.7.822 20.9.822 20.9.822.822 20.9.822 20.9.822 20.9.822.822 20.9.822.822 20.9.822.822 20.9.731 .4061.875 47.61.875 47.61.875 47.61.875 47.61.937 49.21.937 49.21.875 47.61.875 47.61.8751.875 47.61.875 47.61.875 47.61.8751.875 47.61.8751.875 47.61.8751.875 47.62.406 61.11.441.441.441.441.441.441.441.441.441.441.13 28.61.13 28.61.13 28.61.13 28.61.19 30.21.19 30.21.13 28.61.13 28.61.131.13 28.61.13 28.61.13 28.61.131.13 28.61.131.13 28.61.131.13 28.61.13 36.58.008.008.258.258.508.508.758.759.009.004.12 104.64.25 108.04.37 111.14.37 111.14.18 106.24.18 106.25.00 127.05.25 133.45.255.50 139.75.62 142.75.50 139.76.006.00 152.46.256.37 161.96.507.00 177.87.75 0.8120.437 11.10.437 11.10.437 11.10.437 11.10.437 11.10.437 11.10.437 11.10.562 14.30.5620.562 14.30.562 14.30.562 14.30.6870.687 17.50.6870.687 17.50.6870.687 17.50.687 .500BOLT CIRCLE MIN.BY BOLT SIZE3/8 1015/2 123/8 16/4K2.750 702.875 733.000 763.000 763.125 793.125 793.375 863.437 873.5003.625 923.750 953.875 984.0004.062 1034.1254.250 1084.3754.500 1145.250 6253.562 893.6253.750 943.875 974.000 1004.1254.187 1054.2504.375 1104.5004.625 1165.375 7504.2504.312 1094.3754.500 1144.6254.750 1205.500 1396.3756.3756.6256.6256.8756.875METRIC NUMBERS ARE INDICATED IN BOLD RED. STANDARD UTEX SEALS ARE AVAILABLE FOR BOTH INCH AND MILLIMETER SHAFT SIZES LISTED IN COLUMN “A” ABOVE. FOR AVAILABILITY OF SEAL SIZES NOT LISTEDIN THE TABLE, CONTACT YOUR UTEX ERATOR ILIBPATENTEDJ SLOT WIDTH4 PLCS., 90 APARTWITH K MIN. D.B.C.VENTORDRAINBUTEXCWFLUSHVENT / DRAIN2
LIBERATOR II LIBERATOR II Technical DataMATERIALSMETAL PARTS316 SS metal parts are standard.STATIONARY FACECNFJ-B grade carbon is standard. TungstenCarbide and Silicon Carbide are available.ROTATING SEAL FACEAlpha sintered Silicon Carbide.O-RINGSAflas is standard. EPDM, Neoprene,Nitrile, Chemraz, Kalrez, andViton are available.TEMPERATURE-60 F TO 400 F-50 C TO 204 CPRESSURE400 psi27 barSPEED5000 fpm325 m/sThe Liberator II cartridge seal (patented) offers all of the designfeatures of the Liberator I. In addition, it features two tangential outletports for clockwise or counterclockwise pump rotation. A pumpingring built in as a standard feature provides positive barrier fluidcirculation.The Liberator II is a double hydraulically balanced seal whichallows it to be used as a double or tandem seal. In vertical installations,the secondary seal chamber is self-venting to insure proper lubricationof the secondary sealing faces. The barrier fluid at the secondary sealis on the O.D. of the sealing faces, which insures maximum heatdissipation.
SHAFTSIZEINCH MMSTUFFINGBOX BEFOREMIN.MAX.SEAL0.D.ABC1.000 251.125 281.250 30321.375 33351.500 381.562 401.6251.750 451.875 482.000 502.187 552.375 602.625 652.750 6.095.51.875 48.02.000 51.02.125 54.02.125 54.02.250 58.02.250 58.02.500 64.02.562 66.02.6252.750 70.02.875 73.03.000 77.02.8753.187 81.03.0003.375 86.03.2503.625 93.04.250 STUFFINGBOX FG1.875 481.875 481.875 481.875 481.875 481.875 482.000 512.000 512.0002.000 512.000 512.000 512.8122.000 512.9372.000 513.1872.000 512.312 121.750 44.51.750 44.51.750 44.51.750 44.51.750 44.51.750 44.51.875 47.61.875 47.61.8751.875 47.61.875 47.61.875 47.62.0001.875 47.62.0001.875 47.62.0001.875 47.62.181 .4062.406GLANDO.D.SLOTWIDTHBOLT CIRCLE MIN.BY BOLT SIZE3/8 51.951.961.1H1.23 31.31.23 31.31.23 31.31.23 31.31.19 30.21.19 30.21.23 31.31.23 31.31.231.23 31.31.23 31.31.23 31.32.0421.23 31.32.0421.23 31.32.0421.23 31.31.44 36.51.431.431.431.431.431.431.431.431.431.434.12 104.64.25 108.04.37 111.14.37 111.14.18 106.24.18 106.25.00 127.05.25 133.45.255.50 139.75.62 142.75.50 139.71.236.00 152.41.236.37 161.91.237.00 177.87.75 25123/8 7.517.517.517.52.750 702.875 733.000 763.000 763.125 793.125 793.375 863.437 873.5003.625 923.750 953.875 980.6874.062 1030.6874.250 1080.6874.500 1145.250 5003.562 893.6253.750 943.875 974.000 1004.0004.187 1054.1254.375 1104.3754.625 1165.375 6254.1254.312 1094.2504.500 1144.5004.750 1205.500 TRIC NUMBERS ARE INDICATED IN BOLD RED. STANDARD UTEX SEALS ARE AVAILABLE FOR BOTH INCH AND MILLIMETER SHAFT SIZES LISTED IN COLUMN “A” ABOVE. FOR AVAILABILITY OF SEAL SIZES NOT LISTEDIN THE TABLE, CONTACT YOUR UTEX TUTEXERATOR I ILIBPATENTEDUTEXACERATOR I ILIBPATENTEDBJ SLOT WIDTH4 PLCS., 90 APARTWITH K MIN. D.B.C.INLET4
UTEX MB-ISingle Metal Bellows Cartridge SealMB-1 Technical DataMATERIALSBELLOWS & END FITTINGSHastelloy C-276 bellows core. 316 SSstandard end fittings, Hastelloy Cis available.METAL PARTS316 SS metal parts are standard.Hastelloy C and Alloy 20are available.STATIONARY SEAL FACECNFJ-B grade carbon is standard. Tungstencarbide and silicon carbide are available.ROTATING SEAL FACEAlpha sintered silicon carbide.O-RINGSViton is standard. EPDM, Neoprene,Nitrile, Aflas, Chemraz, Kalrez, PTFE, andencapsulated Viton are available.TEMPERATURE-75 F to 400 F (-60 C to 204 C) dependingon o-ring material chosen.PRESSUREMaximum pressure is 300 psi (20 bar)SPEEDUp to 4500 fpm (23 m/s)NOTESVent/Drain and flush connection sizes:1/4" N.P.T. for seal sizes 1" thru 1 3/8"3/8" N.P.T. for seal sizes 1 1/2" thru 2 3/4"5THE UTEX SEAL THAT DOUBLESYOUR OPTIONSThe compact and versatile MB-I can be used as either a stationary orrotating bellows seal. The MB-I is supplied in its standard configurationas a stationary bellows assembly. The mutually interchangeable bellowsand seat allow easy, on- site conversion to a rotary bellows design.The bellows design provides even distribution of load around theentire circumference of the seal face. In addition, the need for dynamico-rings, with associated frictional drag and wear, is eliminated. Theextremely low mass of the face and bellows assembly improves facetracking characteristics during operation.The MB-I’s unique multi-ported flushing system uses a singlegland connection that enters into an annular cavity. The flush mediumflows around this cavity and exits through evenly spaced ports, travelingaxially over the seal faces. This provides full 360 lubrication andcooling while protecting the faces from abrasive particles.The MB-I fits ANSI pumps without modification. Temperaturerange is from -75 F to 400 F (-60 C to 204 C) depending on o-ringmaterial chosen. Maximum pressure is 300 psi (20 bar), with speeds upto 4500 fpm (23 m/s).
SHAFTSIZEINCH MMA1.000 251.125 281.250 30321.375 33351.500 381.625 401.750 451.875 482.000 502.1252.250 552.375 602.5002.625 652.750 70STUFFINGBOX BOREMIN.MAX.B1.625 41.51.750 44.51.875 48.01.875 48.02.000 51.02.000 51.02.250 57.52.375 60.52.500 63.52.625 67.02.750 70.02.8753.000 76.53.125 79.53.2503.375 86.03.750 95.51.875 48.02.000 51.02.125 54.02.125 54.02.250 58.02.250 58.02.500 64.02.625 67.02.750 70.02.875 73.03.000 77.03.2503.375 86.03.625 93.03.7503.875 99.04.000 105.0SEALO.D.CSTUFFINGBOX H1.156 301.156 301.156 301.156 301.156 301.156 301.406 361.406 361.453 371.453 371.453 371.4531.453 371.453 371.4531.453 371.625 421.047 26.61.047 26.61.047 26.61.047 26.61.047 26.61.047 26.61.281 32.51.281 32.51.328 33.71.328 33.71.328 33.71.3281.328 33.71.328 33.71.3281.328 33.71.500 38.11.937 49.21.937 49.21.937 49.21.937 49.21.937 49.21.937 49.22.000 50.82.000 50.82.000 50.82.000 50.82.000 50.82.0002.000 50.82.000 50.82.0002.000 50.82.375 60.31.19 30.21.19 30.21.19 30.21.19 30.21.19 30.21.19 30.21.25 31.81.25 31.81.25 31.81.25 31.81.25 31.81.251.25 31.81.25 31.81.251.25 31.81.43 36.51.562 39.71.687 42.91.812 46.01.812 46.01.937 49.21.937 49.22.187 55.62.312 58.72.437 61.92.562 65.12.687 68.32.8122.937 74.63.062 77.83.1873.312 84.13.625 92.1GLANDO.D.SLOTWIDTHBOLT CIRCLE MIN.BY BOLT SIZE31/8 10GHJ4.11 104.44.11 104.44.18 106.24.18 106.24.18 106.24.18 106.24.49 114.04.99 126.75.49 139.45.49 139.45.49 139.45.995.99 152.16.24 158.56.496.99 177.57.24 183.9.437 11.1.437 11.1.437 11.1.437 11.1.437 11.1.437 11.1.562 14.3.562 14.3.562 14.3.562 14.3.562 14.3.687.687 17.5.687 17.5.687.687 17.5.687 17.52.750 702.875 733.000 763.000 763.125 793.125 793.375 863.500 893.625 923.750 953.875 984.1254.250 1084.500 1144.6254.750 1215.000 127/2 12K3.500 883.625 913.750 943.875 974.000 1004.2504.375 1104.625 1164.7504.875 1235.125 1295/8 164.3754.500 1144.750 1204.8755.000 1275.250 133METRIC NUMBERS ARE INDICATED IN BOLD RED. STANDARD UTEX SEALS ARE AVAILABLE FOR BOTH INCH AND MILLIMETER SHAFT SIZES LISTED IN COLUMN “A” ABOVE. FOR AVAILABILITY OF SEAL SIZESNOT LISTED IN THE TABLE, CONTACT YOUR UTEX REPRESENTATIVE.DFGCAVENT/DRAINEU TM B - I XBE N TO RD R A I NVF L U S HHGLANDO.D.FLUSHJ SLOT WIDTH4 PLCS., 90 APARTWITH K MIN. D.B.C.V E N TO RD R A I NE6
UTEX MB-IIDual Stationary Metal BellowsMB-II Technical DataMATERIALSBELLOWS & END FITTINGSHastelloy C-276 bellows core. 316 SS standardend fittings, Hastelloy C available.METAL PARTS316 SS metal parts are standard. Hastelloy C andAlloy available.STATIONARY SEAL FACECNFJ-B grade carbon is standard. Tungstencarbide and silicon carbide are available.ROTATING SEAL FACEAlpha sintered silicon carbide inboard seal.Reaction bonded silicon carbide outboard seal.O- RINGSViton is standard. EPDM, Neoprene, Nitrile,Aflas, Chemraz, Kalrez, PTFE, and encapsulatedViton are available.TEMPERATURE-75 F to 400 F (-60 C to 204 C) depending ono-ring material chosen.PRESSUREA maximum pressure differential of 300psi (20 bar) across either bellows:Double ModeMax. stuffing box pressure 275 psi (19 bar)Max. buffer pressure 300 psi (20 bar)Tandem ModeMax. stuffing box pressure 300 psi (20 bar)Max. buffer pressure 275 psi (19 bar)SPEED:Up to 4500 fpm (23 m/s)NOTES:1. INLET/OUTLET CONNECTION SIZES:/4" N.P.T. for seal sizes 1" thru 1 1/2"3/8" N.P.T. for seal sizes 1 5/8" thru 2 3/4"17THE UTEX SEAL THAT KEEPS YOUPUMPING LONGERThe unique MB-II can be operated as either a double or tandem seal,both of which are hydraulically balanced, making it one of the mostversatile seals available. It is designed and built to reduce emissions toEPA standards and to increase mean time between planned maintenance(MTBPM).The dual stationary bellows assembly self adjusts for misalignmentand reduces the potential for harmonic vibration. The extremely lowmass of the face and bellows assembly improves face trackingcharacteristics during operation.The buffer fluid is sealed on the O.D. of the outboard bellows. Thisprevents heat related problems resulting from air entrapment and deadfluid zones. Also, higher buffer fluid pressures are attainable. A radialflow pumping ring produces a high performance flow of buffer fluid forefficient cooling and helps prevent abrasives from settling in the sealcavity.The MB-II fits ANSI pumps without modification. Temperaturerange is from -75 F to 400 F (-60 C to 204 C) depending on o-ringmaterial chosen. Maximum pressure differential is 300 psi (20 bar)across either bellows, with speeds up to 4500 fpm (23m/s).
SHAFTSIZEINCH MMSTUFFINGBOX BOREMIN.MAX.SEALO.D.AB1.000 251.125 281.250 30321.375 33351.500 381.625 401.750 451.875 482.000 502.1252.250 552.375 602.5002.625 652.750 701.625 41.51.750 44.51.875 48.01.875 48.02.000 51.02.000 51.02.250 57.52.375 60.52.500 63.52.625 67.02.750 70.02.8753.000 76.53.125 79.53.2503.375 86.03.750 95.51.875 48.02.000 51.02.125 54.02.125 54.02.250 58.02.250 58.02.500 64.02.625 67.02.750 70.02.875 73.03.000 77.03.2503.375 86.03.625 93.03.7503.875 99.04.000 105.0STUFFINGBOX ANDO.D.SLOTWIDTHBOLT CIRCLE MIN.BY BOLT SIZECDEFGHJ1.562 39.71.687 42.91.812 46.01.812 46.01.937 49.21.937 49.22.187 55.62.312 58.72.437 61.92.562 65.12.687 68.32.8122.937 74.63.062 77.83.1873.312 84.13.625 92.11.718 441.718 441.718 441.718 441.718 441.718 441.937 491.937 492.000 512.000 512.000 512.0002.000 512.000 512.0002.000 512.375 611.609 40.91.609 40.91.609 40.91.609 40.91.609 40.91.609 40.91.828 46.41.828 46.41.875 47.61.875 47.61.875 47.61.8751.875 47.61.875 47.61.8751.875 47.62.250 57.22.000 50.82.000 50.82.000 50.82.000 50.82.000 50.82.000 50.82.125 54.02.125 54.02.125 54.02.125 54.02.125 54.02.1252.125 54.02.125 54.02.2152.125 54.02.625 66.71.19 30.21.19 30.21.19 30.21.19 30.21.19 30.21.19 30.21.25 31.81.25 31.81.25 31.81.25 31.81.25 31.81.251.25 31.81.25 31.81.251.25 31.81.50 38.14.11 104.44.11 104.44.18 106.24.18 106.24.18 106.24.18 106.24.49 114.04.99 126.75.49 139.45.49 139.45.49 139.45.995.99 152.16.24 158.56.496.99 177.57.24 183.9.437 11.1.437 11.1.437 11.1.437 11.1.437 11.1.437 11.1.562 14.3.562 14.3.562 14.3.562 14.3.562 14.3.687.687 17.5.687 17.5.687.687 17.5.687 17.531/8" 102.750 702.875 733.000 763.000 763.125 793.125 793.375 863.500 893.625 923.750 953.875 984.1254.250 1084.500 1144.6254.750 1215.000 127/2" 12K3.500 883.625 913.750 943.875 974.000 1004.2504.375 1104.625 1164.7504.875 1235.125 1295/8" 164.3754.500 1144.750 1204.8755.000 1275.250 133METRIC NUMBERS ARE INDICATED IN BOLD RED. STANDARD UTEX SEALS ARE AVAILABLE FOR BOTH INCH AND MILLIMETER SHAFT SIZES LISTED IN COLUMN “A” ABOVE. FOR AVAILABILITY OF SEALSIZES NOT LISTED IN THE TABLE, CONTACT YOUR UTEX REPRESENTATIVE.DEFGHGLANDO.D.OUTLETCCWCWCAINLETJ SLOT WIDTHPLCS., 90 APARTWITH K MIN. D.B.C.EU TM B - I I XBEU TM B - I I XOUTLETI N L E T8
UNILITE UNILITE Technical DataMATERIALSBASE MATERIALPolyphenylene Sulfide Composite.SPRINGHastelloy C-276.STATIONARY FACECNFJ-B grade carbon is standard.Tungsten carbide and silicon carbideare available.ROTATING SEAL FACEAlpha sintered silicon carbide.O-RINGSViton is standard. Aflas, Nitrile, EPDM,Neoprene, Chemraz and Kalrez are available.TEMPERATURE212 F100 CPRESSURE200 psi13.8 barSPEED2950 fpm915 m/sTHE ECONOMICAL, LONG LASTING UNILITEFROM UTEXThe Unilite is a unique non-metallic mechanical seal that deliverseconomy and durability all in a proven design. A metal collar insertprotects the composite material when the set screws are tightened,making this a uniquely rugged design for the field. And because it usesno setting clips, this full cartridge seal is simpler to install than previousmechanical seals. Its features include: The economy of a non-metallic seal Proven polyphenylene sulfide non-metalliccomposite High chemical resistance Available with flush on request No setting clips required Factory repairable
SHAFTSIZEINCH MMA1.000 251.125 281.250 30321.375 351.500 38401.6251.750 451.8752.000 502.125552.2502.375 602.5002.625 65STUFFINGBOX BOREMIN.MAX.B1.625 41.51.750 44.51.875 48.01.875 48.02.000 51.02.250 57.52.312 59.02.3752.500 63.52.6252.750 70.02.8752.937 75.03.0003.125 79.53.2503.375 86.01.875 48.02.000 51.02.125 54.02.125 54.02.250 58.02.500 64.02.562 66.02.6252.750 70.02.8753.000 77.03.1253.187 81.03.2503.375 86.03.5003.625 93.0SEALO.D.STUFFINGBOX EFG1.562 39.71.687 42.81.812 46.01.812 46.01.937 49.22.187 55.62.250 57.22.3122.437 61.92.5622.687 68.32.8122.875 73.02.9373.062 77.83.1873.312 84.10.828 210.828 210.828 210.828 210.828 210.844 220.844 220.8440.844 220.8440.844 220.8440.844 220.8440.844 220.8440.844 220.703 17.90.703 17.90.703 17.90.703 17.90.703 17.90.719 18.30.719 18.30.7190.719 18.30.7190.719 18.30.7190.719 18.30.7190.719 18.30.7190.719 18.31.578 40.11.578 40.11.578 40.11.578 40.11.578 40.11.719 43.71.179 43.71.7191.719 43.71.7191.719 43.71.7191.719 43.71.7191.719 43.71.7191.719 43.7GLANDO.D.SLOTWIDTHBOLT CIRCLE MIN.BY BOLT SIZE3/8 101.00 25.41.00 25.41.00 25.41.00 25.41.00 25.41.14 29.01.14 29.01.141.14 29.01.141.14 29.01.141.14 29.01.141.14 29.01.141.14 29.0HJ4.12 104.84.12 104.84.25 108.04.25 108.04.25 108.04.50 114.35.00 127.05.005.50 139.75.505.50 139.76.006.00 152.46.006.00 152.46.506.50 165.10.437 11.10.437 11.10.437 11.10.437 11.10.437 11.10.437 11.10.562 14.30.5620.562 14.30.5620.562 14.30.6870.687 17.50.6870.687 17.50.6870.687 17.52.750 702.875 733.000 763.000 763.125 793.375 863.437 873.5003.625 923.7503.875 984.0004.062 1034.1254.250 1084.3754.500 1141/2 5004.6255/8 1689941004.250105 4.312 1094.375110 4.500 1144.625116 4.750 120METRIC NUMBERS ARE INDICATED IN BOLD RED. STANDARD UTEX SEALS ARE AVAILABLE FOR BOTH INCH AND MILLIMETER SHAFT SIZES LISTED IN COLUMN “A” ABOVE. FOR AVAILABILITY OF SEALSIZES NOT LISTED IN THE TABLE, CONTACT YOUR UTEX REPRESENTATIVE.TYPICAL MECHANICAL PROPERTIES OF UNILITE COMPOSITE SEALPOLYPHENYLENE SULFIDE COMPOSITETensile strengthUltimate elongationFlexural strengthFlexural modulusNotched IZODHDT @ 264 psi (1.82 MPa)ASTM D638ASTM D638ASTM D790ASTM D790ASTM D256ASTM D648DE22,000 psi1%36,000 psi2,000,000 psi4 ft-lb/in500 F155MPa1%248 MPa14 GPa212 J/M260 CFGHGLANDO.D.UTEXAENTEDUNILITE C1 7 5 0PATBJ SLOT WIDTH,4 PLCS, 90 APARTWITH K MIN. D.B.C.10
UTEX “MB”“MB” Technical DataMATERIALSMETAL COMPONENTS (MB)Hastelloy C-276 bellows core 316SSend fittings.METAL COMPONENTS (MBH)All Hastelloy C-276SEAL FACECNFJ-B grade carbon is standard. Tungstencarbide and silicon carbideare available.O-RINGSViton is standard. EPDM, Neoprene, Nitrile,Aflas, Chemraz, Kalrez, PTFE andencapsulated Viton are available.TEMPERATURE-75 F to 450 F-60 C to 232 Cdepending on o-ring material chosen.PRESSUREOPERATING: Up to 300 psi (20 bar)STATIC: Up to 350 psi (24 bar)Dependent upon seal size.SPEEDUp to 4500 fpm (23 m/s).11The UTEX “MB” metal bellows seal provides unitized construction withsuperior nestled ripple bellows design. It is designed for applicationsinvolving more viscous fluids, such as mud pumps, compressor gasseals, and crude oil handling.Standard materials are 316 stainless steel end fittings with aHastelloy C bellows core. All Hastelloy C construction is also available.A carbon face is standard, and tungsten or silicon carbide faces areoptional.The static o-ring seal eliminates shaft or sleeve fretting. The weldedbellows core provides 360 face loading to reduce vibration andfrictional heat. This integrally balanced seal handles pressure fromvacuum to 300 psi. The seal remains clean running because of therotating bellows which generates a centrifugal force to expel abrasives.UTEX “MB” seals are available in 15/16" through 4" sizes. ConsultUTEX for specific design application information.
SEAL/SHAFTSIZEINCH MMA251.0001.125 .8753.000753.125 803.2503.375 853.500 903.6253.750 953.8754.000 1004.125 1054.250 00039.7 1.1811.25042.8 1.25042.8 1.2791.37546.0 1.27946.0 1.2791.37549.2 1.27952.4 1.3391.37555.6 1.3391.37558.7 1.3391.37558.7 1.3391.50061.9 1.33965.1 1.3581.50068.2 1.3581.50071.4 1.3581.50074.6 1.5551.50081.0 1.5551.62584.1 1.5551.6251.62587.3 1.7501.6251.62595.3 1.75098.4 1.7501.750104.8 1.750108.0 1.7501.750114.3 1.7501.750120.7 1.750123.8 1.750127.O 444.444.4O-RING-120-120-122 -230-231-231-232-232-233-234-234-235 -235-236-237 -237-238 -238-239-240 -240-241-242 -242-243 -243-244 -245SET SCREWSIZE xLENGTHM5-0.8X610-24 x 1/410-24 x 1/4M5-0.8x6M5-0.8x6/4-20 x 1/41M5-0.8x6M5-0.8x6/4-20 x 1/41M5-0.8x6M6-1.0x7/4-20 x 1/41M6-1.0x7/4-20 x 1/41M6-1.0x7/4-20 x 1/41M6-1.0x7/4-20 x 1/41M6-1.0x7M6-1.0x7/4-20 x 1/41M6-1.0x7/4-20 x 1/41M6-1.0x7/4-20 x 1/41M6-1.0x7/4-20 x 1/41M6-1.0x8/4-20 x 5/161M6-1.0x8/4-20 x 5/161/4-20 x 5/161M6-1.0x8/4-20 x 3/81/4-20 x 3/81/4-20 x 3/81/4-20 x 3/81/4-20 x 3/81/4-20 x 3/81/4-20 x 3/81/4-20 x 3/81/4-20 x 3/81/4-20 x 3/81/4-20 x 3/81/4-20 x 6-1.0x10M6-1.0x10M6-1.0x10METRIC NUMBERS ARE INDICATED IN BOLD RED. STANDARD UTEX SEALS ARE AVAILABLE FOR BOTH INCH ANDMILLIMETER SHAFT SIZES LISTED IN COLUMN “A” ABOVE. FOR AVAILABILITY OF SEAL SIZES NOT LISTED INTHE TABLE, CONTACT YOUR UTEX REPRESENTATIVE.B AC12
UTEX “MP”“MP” Technical DataMATERIALSMETAL COMPONENTS316 stainless steel is standard.SEAL FACECNFJ-B grade carbon is standard. Siliconcarbon and special grade carbonare also available.O-RINGSViton, Aflas, Nitrile, EPDM, Neoprene,Chemraz and Kalrez.TEMPERATURE-60 F to 400 F-50 C to 204 CPRESSURE:450 psi31 barSPEED:3940 fpm1320 m/sThe UTEX “MP” is a straight-line, pressure-balanced seal for handlinganything from clean water to crude oil. The design features springs thatare isolated from the product to prevent clogging and fatigue. No slidingelastomers are used that could create shaft or sleeve fretting. Solidcarbon faces are used, eliminating the need for shrink fits and allowingeasy in-plant repairs.This seal has a slim line design that fits AVS and ANSI pumps. Theseal’s integral balance does not require stepped shafts or sleeves andcan be used at operating pressures of 0 to 450 psi. UTEX “MP” seals areavailable through 6" sizes. Consult UTEX for specific design applicationinformation.
SEAL/SHAFTSIZEINCH MMA.937251.000281.125301.1871.250 32331.375351.500 381.562 401.6251.687 42431.750 451.875 482.000 502.125 53552.2502.375 602.500 632.625 652.750 702.8753.000 753.1253.250 803.375 853.500 903.6253.750 953.8754.000 1004.125 1054.2504.375 547 39.31.5621.664 42.31.6871.743 44.31.7501.812 46.01.861 47.31.9371.929 49.02.062 52.42.187 55.62.2502.312 58.72.312 58.72.375 60.32.500 63.52.625 66.72.750 69.82.750 69.82.8753.000 76.23.125 79.43.250 82.63.375 85.73.5003.812 96.83.9374.062 103.24.187 106.44.312 109.54.4374.562 115.94.6874.812 122.24.937 125.45.0625.187 6.4376.5626.6876.8121.7501.375 34.91.7501.375 34.91.7501.375 34.91.7501.750 44.41.750 44.41.7501.750 44.41.750 44.41.750 44.41.7501.750 44.41.750 44.41.750 44.41.750 44.41.750 44.41.750 44.41.750 44.41.7501.750 44.41.750 44.41.750 44.41.750 44.41.7501.750 44.41.7501.750 44.41.750 44.41.750 44.41.7501.750 44.41.7501.750 44.42.250 57.22.2502.250 -120-120SET SCREWSIZE xLENGTH/4 - 20 x 1/41-1125-125-122M5-0.8x6/4 - 20 x 1/41-1127-122-127-123-123-124 -124-125-126-126-128 -128-129 -129-130-131 -131-131-132 -132-134 -134-136 -136-138 -138-139-140-142 -142-144 -144-146 -145-148 -148-150-234 -234-235-236 -235-237 -237-238 -238-239-240 -240-241-242 -242-243 -243-244-245 57-258-128-128-129 -129-130-131-131-133 -133-135 -135-136-137 -137-137-138 -138-140 -140-142 -142-144 -144-144-146-148 -148-150 -150-151 -151-152 -152-152-238 -238-239-240 -240-241 -241-242 -242-243-244 -244-245-246 -246-247 -247-248-249 60-260M5-0.8x6/4 - 20 x 1/41M5-0.8x6/4 - 20 x 1/41/4 - 20 x 1/4 M6-1.0x7M6-1.0x71/4 - 20 x 1/4M6-1.0x71/4 - 20 x 1/4 M6-1.0x71/4 - 20 x 5/16 M6-1.0x71/4 - 20 x 5/161/4 - 20 x 5/16 M6-1.0x7M6-1.0x71/4 - 20 x 5/16 M6-1.0x71/4 - 20 x 5/16 M6-1.0x71/4 - 20 x 5/16 M6-1.0x71/4 - 20 x 5/16 M6-1.0x7M6-1.0x71/4 - 20 x 5/161/4 - 20 x 5/16 M6-1.0x71/4 - 20 x 5/16 M6-1.0x71/4 - 20 x 5/16 M6-1.0x71/4 - 20 x 5/16 M6-1.0x71/4 - 20 x 5/161/4 - 20 x 3/8 M6-1.0x101/4 - 20 x 3/81/4 - 20 x 3/8 M6-1.0x101/4 - 20 x 3/8 M6-1.0x101/4 - 20 x 3/8 M6-1.0x101/4 - 20 x 3/81/4 - 20 x 3/8 M6-1.0x101/4 - 20 x 3/81/4 - 20 x 3/8 M6-1.0x105/16 - 18 x 3/8 M8-1.25x105/16 - 18 x 3/85/16 - 18 x 3/8 M8-1.25x105/16 - 18 x 3/85/16 - 18 x 3/85/16 - 18 x 3/85/16 - 18 x 3/85/16 - 18 x 3/85/16 - 18 x 3/85/16 - 18 x 3/85/16 - 18 x 3/85/16 - 18 x 3/85/16 - 18 x 3/85/16 - 18 x 3/85/16 - 18 x 3/85/16 - 18 x 3/81METRIC NUMBERS ARE INDICATED IN BOLD RED. STANDARD UTEX SEALS ARE AVAILABLE FOR BOTH INCH AND MILLIMETERSHAFT SIZES LISTED IN COLUMN “A” ABOVE. FOR AVAILABILITY OF SEAL SIZES NOT LISTED IN THE TABLE, CONTACT YOURUTEX REPRESENTATIVE.BAC14
UTEX “CO”“CO” Technical DataMATERIALSMETAL COMPONENTS316 stainless steel is standard.SEAL FACECNFJ-B grade carbon is standard. Glassfilled PTFE and special grade carbonare also available.O-RINGSViton, Aflas, Nitrile, EPDM, Neoprene,Chemraz and Kalrez.TEMPERATURE-60 F to 400 F-50 C to 204 CPRESSURE:150 psiSEAL/SHAFTSIZEINCH MMASEALO.D.1.000 24251.125 281.250 30321.375 33351.500 381.625 401.750 4243451.875 482.000 502.125 532.250 552.375 602.500 632.625 652.750 702.8753.000 753.1253.250 803.375 853.5003.625 903.750 953.8754.000 1002.000 50.82.000 50.82.125 54.02.250 57.22.250 57.22.375 60.32.375 60.32.500 63.52.625 66.72.750 69.92.750 69.92.750 69.92.875 73.03.000 76.23.125 79.43.250 82.63.375 85.73.500 88.93.625 92.13.875 98.44.0004.125 104.84.2504.375 111.14.500 114.34.6254.750 120.74.875 123.85.0005.125 130.2BINSTALLEDLENGTHO-RINGSET SCREWSIZE xLENGTHC1.500 38.11.500 38.11.500 38.11.500 38.11.500 38.11.500 38.11.500 38.11.500 38.11.500 38.11.500 38.11.500 38.11.500 38.11.500 38.11.500 38.11.500 38.11.500 38.11.500 38.11.500 38.11.500 38.11.500 38.11.5001.500 38.11.5001.500 38.11.500 38.11.5001.500 38.11.500 38.11.5001.500 38.1-318 -317-318-320 -320-322 -321-322-324 -323-324-325 -325-326 -326-327 -326-327-327-328 -328-329 -329-330 -330-331 -330-332 -332-333 -333-334 -334-335 -335-336-337 -337-338-339 -338-340 -340-341-342 -341-343 -343-344-3
metal bellows cartridge seals high pressure pipeline seals composite cartridge seals rotary units metal bellows multi spring outside mount stationary seats o-ring block clamp “l” type utex industries, inc. utex industr
akuntansi musyarakah (sak no 106) Ayat tentang Musyarakah (Q.S. 39; 29) لًََّز ãَ åِاَ óِ îَخظَْ ó Þَْ ë Þٍجُزَِ ß ا äًَّ àَط لًَّجُرَ íَ åَ îظُِ Ûاَش
Collectively make tawbah to Allāh S so that you may acquire falāḥ [of this world and the Hereafter]. (24:31) The one who repents also becomes the beloved of Allāh S, Âَْ Èِﺑاﻮَّﺘﻟاَّﺐُّ ßُِ çﻪَّٰﻠﻟانَّاِ Verily, Allāh S loves those who are most repenting. (2:22
Robert King and Albert Woodfox. Excellent facilities The School is based in the John Foster Building on the Mount Pleasant campus and here you’ll find high specification learning and teaching rooms, lecture theatres and a large IT suite. The building itself, a former convent, has a fascinating history and many of its original features remain, including the Moot Room which hosts large .
An Introduction to Random Field Theory Matthew Brett , Will Penny †and Stefan Kiebel MRC Cognition and Brain Sciences Unit, Cambridge UK; † Functional Imaging Laboratory, Institute of Neurology, London, UK. March 4, 2003 1 Introduction This chapter is an introduction to the multiple comparison problem in func-
"Good counselling is just excellent communication skills! Or is it?" Authors: Ms Merrelyn Bates Mr Paul Stevenson ABSTRACT There have been arguments about whether counselling is a new profession while other established professions engage in similar practices and have a legitimacy of their own. Theoretical frameworks for professional counselling are discussed with an emphasis on practice .
Beverages which are unfit for consumption and which have to be discarded are waste. There are many options available to businesses to manage this waste and this guidance sets out a hierarchy of these options. The hierarchy is based on the waste hierarchy which prioritises recycling and recovery of waste over its disposal. 2.5. Recovery and disposal of waste alcoholic beverages is controlled by .
Reading for Re-creating (Calicut University Publications) Academic Skills (OUP) Murphy’s English Grammar (CUP) A Glossary of . It will introduce you to the texts that reflect a range of historical, cultural and aesthetic values. The course also reflects on the aspects of instruction, entertainment, society, class and gender as perceived in the nineteenth century England. The outcome of the .
Flexible printed circuits are found in everything from automobiles, VCR's, camcorders, portable phones and SLR cameras to sophisticated military and avionics systems. High-profile applications of flexible circuits are many. one example is the application of flexible-circuit technology in a rigid flex wire harness used on Sojourner, the robot that roamed the surface of Mars collecting data .
