SECTION 3 EXPLORER ORIGIN SPECIFICATIONS 3.0
SECTION 3EXPLORER ORIGIN SPECIFICATIONSThe following are instructions governing the quality of products offered for shipment as FungibleProducts.3.0INTRODUCTIONThe American Society for Test Materials (ASTM) latest test methods will apply for all testingof products unless otherwise indicated in the specifications or required by federal, state orlocal regulations.3.1GENERAL3.1.1The finished product shall be free of undissolved water, sediment or other foreignmaterials in suspension and shall be clear and bright in origin shipping tanks. Top,middle, and bottom samples may not vary more than 1.0 API from the gravity of thecomposite. The product temperature of shipping tanks must not exceed 100 F.3.1.2Two hours prior to lifting, Shipper will be required to furnish to Explorer a Certificateof Analysis warranting to Explorer that all the product scheduled for transportation asa Fungible product meets the required specifications established by Explorer.Explorer may sample and test shipments of Fungible products prior to acceptance,and in the event of variance between Shipper’s certificate and Explorer’s test, the lattershall prevail.Acceptance of Fungible products into Explorer prior to receipt of the Certificate ofAnalysis or testing of products by Explorer during receipt of shipment does notconstitute a waiver of product specification requirements, nor relieve the shipper ofthe responsibility for furnishing a Certificate of Analysis to Explorer.3.1.3All product shipped must be an EPA certified fuel unless it is specifically designatedas a Blend Stock, Specialty Grade or Transmix.3.1.4Explorer may sample and have tested each batch of fungible products forspecifications tests. The expense of sampling and testing any off specification productwill be for the Shippers account.3.1.5Any tests performed by Explorer are for Explorer’s information and shall in no wayrelieve Shipper of the necessity for compliance with specifications.3.1.6If any of the test data obtained in the examination of scheduled shipments arequestionable, a recheck will be made.3.1.7Explorer reserves the right to reject any products into their fungible stream when asample obtained from any tank level or line sample at origins is found to deviate fromthe Shipper’s Certificate of Analysis. Products not meeting fungible specifications maybe moved as segregated batches and the Shipper will be so advised.Dated: July 1, 2018Section 3-1
3.1.8Explorer reserves the right to sample and check the water level below any product intankage, including tank lines, scheduled for shipment. Water in tank lines is to bedrained prior to pumping.3.1.9Explorer reserves the right to reject gasolines, jet fuels, fuel oils and any other productsscheduled for shipment that contain water or other impurities in accordance with Item10 of current FERC tariff. This includes undissolved water, haze, or cloudy conditionspresent in samples from origin tankage or at points of custody transfer at originlocations. Fuel oils will be considered acceptable if they pass a maximum #2 haze(ASTM D4176) rating in origin tankage or at points of custody transfer at originlocations. Distillates may not exceed 250 ppm of water as measured by D-6304.Gasoline may not exceed 250 ppm of water as measured by D-6304. Jet Fuel may notexceed 150 ppm of water as measured by D-6304. Explorer may require the shipperto remove the water received, and/or invoice the shipper for water disposal andassociated costs.3.1.10 Heavy metals are not allowed to be present.3.1.11 Shipper will perform quarterly oversight testing to ensure that levels of phosphorousdo not exceed allowable limits. Phosphorous, grams /gal ASTM D3231 max. 0.004.(1ppm)3.1.12 Gasoline grades may not contain oxygenates, such as ethers and alcohols. The use ofany non-hydrocarbon blending component is prohibited. Origin maximum for MTBEis .25 vol % before blending.3.1.13 Biodiesel is not allowed to be present at origin.Dated: July 1, 2018Section 3-2
3.2FUNGIBLE SPECIFICATIONSCODE 1ADILUENTThis product does not meet the requirements for gasoline.ASTM TESTMETHODPRODUCT PROPERTYGravity, API @ 60 FD287, D1298, D4052DensityKg/m3D4052ColorUNDYEDBS&W Vol%D95Total Suspended Solids mg/lD4807Corrosion (Cu) 3 Hrs. @D130122 FH2S Liquid wt.ppmD5623Doctor or:D4952Mercaptan Sulfur wt.ppmD5623C1, C2, C3Sulfur, (wt.ppm)D2622, D5453, D7039Gum, mg/100ml after washing D381Gum, mg/100ml unwashedD381Benzene, vol. %D3606, D4053Oxidation Stability - MinutesD525Appearance @ 70 FOdor NonoffensiveReid Vapor Pressure psiD5191Saybolt ColorD156Olefins Vol %D5443Oxygenates wt.ppmD6729 D4815Paraffins Vol %D5443Naphthenes Vol %D5443Aromatics Vol %D5443Organic Chlorides wt.ppmD4929Isobutane Vol %D6730n-Butane Vol %D6730Extract water pHD2110Octane:Dated: July 1, 2018RON: MinimumMON: Minimum(R M)/2 (AKI):D2699D2700MinimumSPECIFICATIONS (1)MINIMUM 4Report1.6240(3)(5)14.94 20.5110090report2 1.00.7003.0reportReportReport60Section 3-3
CODE 1A(1)Deliveries may be higher or lower by normal testing and handling tolerance. All tests shouldbe the most current version or the version specified by federal, state, or local government.(2)Mercaptan Sulfur waived if fuel is negative by doctor test.(3)This product shall be free from undissolved water, sediment or other foreign materials insuspension.(4)This product must be oxygenate free. Non hydrocarbon blending components are notallowed.(5)Any Gasoline exhibiting an offensive odor and/or poses a personal health hazard and/orcontains more than 0.30 wt. % dicyclopentadiene will not be accepted for shipment.Dated: July 1, 2018Section 3-4
FUNGIBLE SPECIFICATIONSCODE 1BDILUENTThis product does not meet the requirements for gasoline.ASTM TESTMETHODPRODUCT PROPERTYGravity, API @ 60 FDensityKg/m3ColorBS&W Vol%Total Suspended Solids mg/lCorrosion (Cu) 3 Hrs. @122 FD287, D1298, D4052D4052UNDYEDD95D4807D130Corrosion (Ag) 3 Hrs. @ 122 FD4814D5623D4952D5623H2S Liquid wt.ppmDoctor or:Mercaptan Sulfur wt.ppmC1, C2, C3Sulfur, (wt.ppm)Gum, mg/100ml after washingGum, mg/100ml unwashedBenzene, vol. %Oxidation Stability - MinutesAppearance @ 70 FOdor NonoffensiveReid Vapor Pressure psiSaybolt ColorOlefins Vol %Oxygenates wt.ppmParaffins Vol %Naphthenes Vol %Aromatics Vol %Organic Chlorides wt.ppmIsobutane Vol %n-Butane Vol %Extract water pHOctane:Dated: July 1, 2018SPECIFICATIONS (1)MINIMUM 622, D5453, D7039D381D381D3606, D4053D5253504Report1.6240(3)(5)D5191D156D5443D6729 D4815D5443D5443D5443D4929D6730D6730D2110RON: MinimumMON: Minimum(R M)/2 (AKI):D2699D2700Minimum14.94 20.5110090Report2 1.00.7003.0ReportReportReport60Section 3-5
CODE 1B(1)Deliveries may be higher or lower by normal testing and handling tolerance. All tests shouldbe the most current version or the version specified by federal, state, or local government.(2)Mercaptan Sulfur waived if fuel is negative by doctor test.(3)This product shall be free from undissolved water, sediment or other foreign materials insuspension.(4)This product must be oxygenate free. Non-hydrocarbon blending components are notallowed.(5)Any Gasoline exhibiting an offensive odor and/or poses a personal health hazard and/orcontains more than 0.30 wt. % dicyclopentadiene will not be accepted for shipment.Dated: July 1, 2018Section 3-6
FUNGIBLE SPECIFICATIONSCODE 31CONVENTIONAL PREMIUM GASOLINEHOUSTON - DALLAS, TX AREASThis product does not meet the requirements for reformulated gasoline, and may not be used in anyreformulated gasoline covered area.ASTM TESTSPECIFICATIONS (1)METHODPRODUCT PROPERTYMINIMUM MAXIMUMGravity, API @ 60 FD287, D1298, D4052ReportColorUndyedCorrosion (Cu) 3 Hrs. @ 122 FD1301Corrosion (Ag) 3 Hrs. @ 122 FD76711Gum, mg/100ml after washingD3814Gum, mg/100ml unwashedD381ReportDistillationD86ReportDoctor or:D4952Negative (2)Mercaptan Sulfur, wt. %D32270.002Sulfur (ppmwt)D2622, D5453, D703980Benzene, vol. %D3606, D40533.8Oxidation Stability - MinutesD525240Appearance @ 70 F(3)Oxygen Content, wt. %D4815, D55990.05 (4)OdorNonoffensive(5)Octane:RON: MinimumMON: Minimum(R M)/2 (AKI):D2699D2700MinimumVolatility - Refer to Section 3Distillation - Refer to Section 3Drivability Index (Origin) – See “Documents & Forms” onCarrier’s website: www.expl.com/pipeline/shipping/manualsReid Vapor Pressure – See “Documents & Forms” on Carrier’swebsite: www.expl.com/pipeline/shipping/manualsAdditives: Gum Inhibitors, Metal DeactivatorsDated: July 1, 2018ReportReport93.0Page # or Doc Name3-33-3RVP – Drive IndexRVP – Vapor PressureSchedule3-5Section 3-7
CODE 31(1)Deliveries may be higher or lower by normal testing and handling tolerance.(2)Mercaptan Sulfur waived if fuel is negative by doctor test.(3)This product shall be free from undissolved water, sediment or other foreign materials insuspension.(4)This product must be oxygenate free. Non-hydrocarbon blending components are notallowed.(5)Any Gasoline exhibiting an offensive odor and/or poses a personal health hazard and/orcontains more than 0.30 wt. % dicyclopentadiene will not be accepted for shipment.(6)For product blended to meet state or EPA imposed summer RVP requirements, tests mustbe performed in accordance with the procedures described in 40 CFR, Part 80. Product mustmeet state, local or EPA specifications at destination.Vapor pressure requirements at destination are based on ASTM Standard D4814 EPA and/orState standards. Due to in-transit times for destinations, Explorer will publish Reid VaporPressure schedules by cycle number for origin locations.The Reid Vapor Pressures published by cycle number are estimations based on Explorer intransit time and federal and state volatility laws applicable within the designated distributionareas.Shipper terminals should monitor inventories to ensure that motor gasolines comply withfederal and state volatility requirementsDated: July 1, 2018Section 3-8
FUNGIBLE SPECIFICATIONSCODE 36CONVENTIONAL PREMIUM GASOLINECENTRAL MISSOURI - SOUTHERN ILLINOISThis product does not meet the requirements for reformulated gasoline, and may not be used in anyreformulated gasoline covered area.ASTM TESTSPECIFICATIONS (1)METHODPRODUCT PROPERTYMINIMUM MAXIMUMGravity, API @ 60 FD287, D1298, D4052ReportColorUndyedCorrosion (Cu) 3 Hrs. @ 122 FD1301Corrosion (Ag) 3 Hrs. @ 122 FD76711Gum, mg/100ml after washingD3814Gum, mg/100ml unwashedD381ReportDistillationD86ReportDoctor or:D4952Negative (2)Mercaptan Sulfur, wt. %D32270.002Sulfur wt. %D2622, D5453, D703980Benzene, vol. %D3606, D40533.8Oxidation Stability - MinutesD525240Appearance @ 70 F(3)Oxygen Content, wt. %D4815, D55990.05 (4)OdorNonoffensive(5)Octane:RON: MinimumMON: Minimum(R M)/2 (AKI):D2699D2700MinimumVolatility - Refer to Section 3Distillation - Refer to Section 3Drivability Index (Origin) – See “Documents & Forms” onCarrier’s website: www.expl.com/pipeline/shipping/manualsReid Vapor Pressure – See “Documents & Forms” on Carrier’swebsite: www.expl.com/pipeline/shipping/manualsAdditives: Gum Inhibitors, Metal DeactivatorsDated: July 1, 2018ReportReport93.0Page # or Doc Name3-33-3RVP – Drive IndexRVP – Vapor PressureSchedule3-5Section 3-9
CODE 36(1)Deliveries may be higher or lower by normal testing and handling tolerance. All tests shouldbe the most current version or the version specified by federal, state, or local government.(2)Mercaptan Sulfur waived if fuel is negative by doctor test.(3)This product shall be free from undissolved water, sediment or other foreign materials insuspension.(4)This product must be oxygenate free. Non hydrocarbon blending components are notallowed.(5)Any Gasoline exhibiting an offensive odor and/or poses a personal health hazard and/orcontains more than 0.30 wt. % dicyclopentadiene will not be accepted for shipment.(6)For product blended to meet state or EPA imposed summer RVP requirements, tests mustbe performed in accordance with the procedures described in 40 CFR, Part 80. Product mustmeet state, local or EPA specifications at destination.Vapor pressure requirements at destination are based on ASTM Standard D4814 EPA and/orState standards. Due to in-transit times for destinations, Explorer will publish Reid VaporPressure schedules by cycle number for origin locations.The Reid Vapor Pressures published by cycle number are estimations based on Explorer intransit time and federal and state volatility laws applicable within the designated distributionareas.Shipper terminals should monitor inventories to ensure that motor gasolines comply withfederal and state volatility requirementsDated: July 1, 2018Section 3-10
FUNGIBLE SPECIFICATIONSREFORMULATED PREMIUM GASOLINE BLENDSTOCK (PBOB)FOR BLENDING WITH 10% DENATURED FUEL ETHANOL(92% PURITY) AS DEFINED IN ASTM D4806VOC-CONTROLLED REGION 1 COMPLEX MODEL PHASE IIHOUSTON-DALLAS AREACODE 3CThe following parameters apply before blending with denatured fuel ethanol:ASTM TESTSPECIFICATIONS (1)METHODPRODUCT PROPERTYMINIMUM MAXIMUMGravity, API @ 60 FD287, D1298, D4052ReportColorUndyedCorrosion (Cu) 3 Hrs. @ 122 FD1301Corrosion (Ag) 3 Hrs. @ 122 FD76711Gum, mg/100ml after washingD3814Gum, mg/100ml Negative (2)or: Mercaptan Sulfur wt. %D32270.002Sulfur wt. (ppm wt.)D2622, D5453, D703980Oxidation Stability - MinutesD525240Appearance @ 70 F(3)Oxygen Content, wt. %D4815, D55990.05 (4)OdorNonoffensive(5)The following parameters apply after blending with denatured fuel ethanol:ASTM TESTSPECIFICATIONS (1)METHODPRODUCT PROPERTYMINIMUM MAXIMUMSulfur, (ppmwt)D2622, D5453, D703980Benzene, vol. %D36061.30Aromatics (vol %)D5769, D559950.0 (6)Olefins (vol %)D1319, D655025.0Oxygen, wt. %D4815, D55991.74.0 (7)Emission Performance Reduction (%)27.0E200 (vol %)D8630.070.0E300 (vol %)D8670.0100.0Octane:RON: MinimumMON: Minimum(R M)/2 (AKI):D2699D2700ReportReport93.0 (8)Page # or Doc NameVolatility - Refer to Section 33-3Distillation - Refer to Section 33-3Drivability Index (Origin) – See “Documents & Forms” on Carrier’sRVP – Drive Indexwebsite: www.expl.com/pipeline/shipping/manualsReid Vapor Pressure – See “Documents & Forms” on Carrier’s website:RVP – Vapor duleAdditives: Gum Inhibitors, Metal Deactivators3-5NOTE: This RBOB may not be combined with any other RBOB except RBOB having the same requirementfor oxygenate type and amount.Dated: July 1, 2018Section 3-11
CODE 3C(1)Deliveries may be higher or lower by normal testing and handling tolerance. All tests shouldbe the most current version or the version specified by federal, state, or local government.(2)Mercaptan Sulfur waived if fuel is negative by doctor test.(3)This product shall be free from undissolved water, sediment or other foreign materials insuspension. See paragraph 3.1.8.(4)This product must be oxygenate free. Non hydrocarbon blending components are not allowed(5)Any Gasoline exhibiting an offensive odor and/or poses a personal health hazard and/orcontains more than 0.30 wt. % dicyclopentadiene will not be accepted for shipment(6)Refer to test methods published in 40 CFR Chapter 1, Part 80.46. ASTM methods D1319 andD4815 may be used in accordance with Federal and State laws.(7)Refer to test method published in 40 CFR, Part 80, Appendix E, Method 3.(8a)This product must be blended with 10% by volume Denatured Fuel Grade Ethanol.(8b)Federal RFG maximum and minimum testing requirement will apply to the final blends of thisproduct.(8c)This product, when blended with 10% volume percent of Denatured Fuel Grade Ethanol, andmust have a Benzene level of 1.3 volume % or lower and have an Oxygen content of at least1.7% but not more than 4.0% by wt.Dated: July 1, 2018Section 3-12
FUNGIBLE SPECIFICATIONSCODE 3DREFORMULATED PREMIUM GASOLINE BLENDSTOCK (PBOB)FOR BLENDING WITH 10% DENATURED FUEL ETHANOL(92% PURITY) AS DEFINED IN ASTM D4806NON-VOC-CONTROLLED REGION 1 COMPLEX MODEL PHASE IIHOUSTON-DALLAS AREAThe following parameters apply before blending with denatured fuel ethanol:ASTM TESTSPECIFICATIONS (1)METHODPRODUCT PROPERTYMINIMUM MAXIMUMGravity, API @ 60 FD287, D1298, D4052ReportColorUndyedCorrosion (Cu) 3 Hrs. @ 122 FD1301Corrosion (Ag) 3 Hrs. @ 122 FD76711Gum, mg/100ml after washingD3814Gum, mg/100ml Negative (2)or: Mercaptan Sulfur wt. %D32270.002Oxidation Stability - MinutesD525240Appearance @ 70 F(3)Oxygen Content, wt. %D4815, D55990.05 (4)OdorNonoffensive(5)The following parameters apply after blending with denatured fuel ethanol:ASTM TESTSPECIFICATIONS (1)METHODPRODUCT PROPERTYMINIMUM MAXIMUMSulfur, (ppmwt)D2622, D5453, D703980Benzene, vol. %D36061.30Aromatics (vol %)D5769, D559950.0 (6)Olefins (vol %)D1319, D655025.0Oxygen, wt. %D4815, D55991.74.0 (7)Emission Performance Reduction (%)27.0E200 (vol %)D8630.070.0E300 (vol %)D8670.0100.0Octane:RON: MinimumMON: Minimum(R M)/2 (AKI):D2699D2700ReportReport93.0 (8)Page # or Doc NameVolatility - Refer to Section 33-3Distillation - Refer to Section 33-3Drivability Index (Origin) – See “Documents & Forms” on Carrier’sRVP – Drive Indexwebsite: www.expl.com/pipeline/shipping/manualsReid Vapor Pressure – See “Documents & Forms” on Carrier’s website:RVP – Vapor duleAdditives: Gum Inhibitors, Metal Deactivators3-5NOTE: This RBOB may not be combined with any other RBOB except RBOB having the same requirementfor oxygenate type and amount.Dated: July 1, 2018Section 3-13
CODE 3D(1)Deliveries may be higher or lower by normal testing and handling tolerance. All tests shouldbe the most current version or the version specified by federal, state, or local government.(2)Mercaptan Sulfur waived if fuel is negative by doctor test.(3)This product shall be free from undissolved water, sediment or other foreign materials insuspension. See paragraph 3.1.8.(4)This product must be oxygenate free. Non hydrocarbon blending components are not allowed(5)Any Gasoline exhibiting an offensive odor and/or poses a personal health hazard and/orcontains more than 0.30 wt. % dicyclopentadiene will not be accepted for shipment(6)Refer to test methods published in 40 CFR Chapter 1, Part 80.46. ASTM methods D1319 andD4815 may be used in accordance with Federal and State laws.(7)Refer to test method published in 40 CFR, Part 80, Appendix E, Method 3.(8a)This product must be blended with 10% by volume Denatured Fuel Grade Ethanol.(8b)Federal RFG maximum and minimum testing requirement will apply to the final blends of thisproduct.(8c)This product, when blended with 10% volume percent of Denatured Fuel Grade Ethanol, andmust have a Benzene level of 1.3 volume % or lower and have an Oxygen content of at least1.7% but not more than 4.0% by wt.Dated: July 1, 2018Section 3-14
FUNGIBLE SPECIFICATIONSCODE 3SREFORMULATED PREMIUM GASOLINE BLENDSTOCK (PBOB) **FOR BLENDING WITH 10% DENATURED FUEL ETHANOL(92% PURITY) AS DEFINED IN ASTM D4806VOC-CONTROLLED REGION 1 COMPLEX MODEL PHASE IIST. LOUIS AREAThe following parameters apply before blending with denatured fuel ethanol:ASTM TESTSPECIFICATIONS (1)METHODPRODUCT PROPERTYMINIMUM MAXIMUMGravity, API @ 60 FD287, D1298, D4052ReportColorUndyedCorrosion (Cu) 3 Hrs. @ 122 FD1301Corrosion (Ag) 3 Hrs. @ 122 FD76711Gum, mg/100ml after washingD3814Gum, mg/100ml Negative (2)or: Mercaptan Sulfur wt. %D32270.002Oxidation Stability - MinutesD525240Appearance @ 70 F(3)Oxygen Content, wt. %D4815, D55990.05 (4)OdorNonoffensive(5)The following parameters apply after blending with denatured fuel ethanol:ASTM TESTSPECIFICATIONS (1)METHODPRODUCT PROPERTYMINIMUM MAXIMUMSulfur, (ppmwt)D2622, D5453, D703980Benzene, vol. %D36061.30Aromatics (vol %)D5769, D559950.0 (6)Olefins (vol %)D1319, D655025.0Oxygen, wt. %D4815, D55991.74.0 (7)Emission Performance Reduction (%)27.0E200 (vol %)D8630.070.0E300 (vol %)D8670.0100.0Octane:RON: MinimumMON: Minimum(R M)/2 (AKI):D2699D2700ReportReport93.0 (8)Page # or Doc NameVolatility - Refer to Section 33-3Distillation - Refer to Section 33-3Drivability Index (Origin) – See “Documents & Forms” on Carrier’sRVP – Drive Indexwebsite: www.expl.com/pipeline/shipping/manualsReid Vapor Pressure – See “Documents & Forms” on Carrier’s website:RVP – Vapor duleAdditives: Gum Inhibitors, Metal Deactivators3-5NOTE: This RBOB may not be combined with any other RBOB except RBOB having the same requirementfor oxygenate type and amount.Dated: July 1, 2018Section 3-15
CODE 3S(1)Deliveries may be higher or lower by normal testing and handling tolerance. All tests shouldbe the most current version or the version specified by federal, state, or local government.(2)Mercaptan Sulfur waived if fuel is negative by doctor test.(3)This product shall be free from undissolved water, sediment or other foreign materials insuspension. See paragraph 3.1.8.(4)This product must be oxygenate free. Non hydrocarbon blending components are not allowed(5)Any Gasoline exhibiting an offensive odor and/or poses a personal health hazard and/orcontains more than 0.30 wt. % dicyclopentadiene will not be accepted for shipment(6)Refer to test methods published in 40 CFR Chapter 1, Part 80.46. ASTM methods D1319 andD4815 may be used in accordance with Federal and State laws.(7)Refer to test method published in 40 CFR, Part 80, Appendix E, Method 3.(8a)This product must be blended with 10% by volume Denatured Fuel Grade Ethanol.(8b)Federal RFG maximum and minimum testing requirement will apply to the final blends of thisproduct.(8c)This product, when blended with 10% volume percent of Denatured Fuel Grade Ethanol, andmust have a Benzene level of 1.3 volume % or lower and have an Oxygen content of at least1.7% but not more than 4.0% by wt.Dated: July 1, 2018Section 3-16
FUNGIBLE SPECIFICATIONSCODE 3TREFORMULATED PREMIUM GASOLINE BLENDSTOCK (PBOB)FOR BLENDING WITH 10% DENATURED FUEL ETHANOL(92% PURITY) AS DEFINED IN ASTM D4806NON-VOC-CONTROLLED COMPLEX MODEL PHASE IIST. LOUIS AREAThe following parameters apply before blending with denatured fuel ethanol:ASTM TESTSPECIFICATIONS (1)METHODPRODUCT PROPERTYMINIMUM MAXIMUMGravity, API @ 60 FD287, D1298, D4052ReportColorUndyedCorrosion (Cu) 3 Hrs. @ 122 FD1301Corrosion (Ag) 3 Hrs. @ 122 FD76711Gum, mg/100ml after washingD3814Gum, mg/100ml Negative (2)or: Mercaptan Sulfur wt. %D32270.002Oxidation Stability - MinutesD525240Appearance @ 70 F(3)Oxygen, wt. %D4815, D55990.05 (4)OdorNonoffensive(5)The following parameters apply after blending with denatured fuel ethanol:ASTM TESTSPECIFICATIONS (1)METHODPRODUCT PROPERTYMINIMUM MAXIMUMSulfur, (ppmwt)D2622, D5453, D703980Benzene, vol. %D36061.30Aromatics (vol %)D5769, D559950.0 (6)Olefins (vol %)D1319, D655025.0Oxygen, wt. %D4815, D55991.74.0 (7)Emission Performance Reduction (%)27.0E200 (vol %)D8630.070.0E300 (vol %)D8670.0100.0Octane:RON: MinimumMON: Minimum(R M)/2 (AKI):D2699D2700ReportReport93.0 (8)Page # or Doc NameVolatility - Refer to Section 33-3Distillation - Refer to Section 33-3Drivability Index (Origin) – See “Documents & Forms” on Carrier’sRVP – Drive Indexwebsite: www.expl.com/pipeline/shipping/manualsReid Vapor Pressure – See “Documents & Forms” on Carrier’s website:RVP – Vapor duleAdditives: Gum Inhibitors, Metal Deactivators3-5NOTE: This RBOB may not be combined with any other RBOB except RBOB having the same requirementfor oxygenate type and amount.Dated: July 1, 2018Section 3-17
CODE 3T(1)Deliveries may be higher or lower by normal testing and handling tolerance. All tests shouldbe the most current version or the version specified by federal, state, or local government.(2)Mercaptan Sulfur waived if fuel is negative by doctor test.(3)This product shall be free from undissolved water, sediment or other foreign materials insuspension. See paragraph 3.1.8.(4)This product must be oxygenate free. Non hydrocarbon blending components are not allowed(5)Any Gasoline exhibiting an offensive odor and/or poses a personal health hazard and/orcontains more than 0.30 wt. % dicyclopentadiene will not be accepted for shipment(6)Refer to test methods published in 40 CFR Chapter 1, Part 80.46. ASTM methods D1319 andD4815 may be used in accordance with Federal and State laws.(7)Refer to test method published in 40 CFR, Part 80, Appendix E, Method 3.(8a)This product must be blended with 10% by volume Denatured Fuel Grade Ethanol.(8b)Federal RFG maximum and minimum testing requirement will apply to the final blends of thisproduct.(8c)This product, when blended with 10% volume percent of Denatured Fuel Grade Ethanol, andmust have a Benzene level of 1.3 volume % or lower and have an Oxygen content of at least1.7% but not more than 4.0% by wt.Dated: July 1, 2018Section 3-18
FUNGIBLE SPECIFICATIONSCODE 3UREFORMULATED PREMIUM GASOLINE BLENDSTOCK (PBOB)FOR BLENDING WITH 10% DENATURED FUEL ETHANOL(92% PURITY) AS DEFINED IN ASTM D4806VOC-CONTROLLED REGION 2 COMPLEX MODEL PHASE IICHICAGO AREAThe following parameters apply before blending with denatured fuel ethanol:ASTM TESTSPECIFICATIONS (1)METHODPRODUCT PROPERTYMINIMUM MAXIMUMGravity, API @ 60 FD287, D1298, D4052ReportColorUndyedCorrosion (Cu) 3 Hrs. @ 122 FD1301Corrosion (Ag) 3 Hrs. @ 122 FD76711Gum, mg/100ml after washingD3814Gum, mg/100ml Negative (2)or: Mercaptan Sulfur wt. %D32270.002Oxidation Stability - MinutesD525240Appearance @ 70 F(3)Oxygen Content, wt. %D4815, D55990.05 (4)OdorNonoffensive(5)The following parameters apply after blending with denatured fuel ethanol:ASTM TESTSPECIFICATIONS (1)METHODPRODUCT PROPERTYMINIMUM MAXIMUMSulfur, (ppmwt)D2622, D5453, D703980Benzene, vol. %D36061.30Aromatics (vol %)D5769, D559950.0 (6)Olefins (vol %)D1319, D655025.0Oxygen, wt. %D4815, D55991.74.0 (7)Emission Performance Reduction (%)25.4E200 (vol %)D8630.070.0E300 (vol %)D8670.0100.0Octane:RON: MinimumMON: Minimum(R M)/2 (AKI):D2699D2700ReportReport93.0 (8)Page # or Doc NameVolatility - Refer to Section 33-3Distillation - Refer to Section 33-3Drivability Index (Origin) – See “Documents & Forms” on Carrier’sRVP – Drive Indexwebsite: www.expl.com/pipeline/shipping/manualsReid Vapor Pressure – See “Documents & Forms” on Carrier’s website:RVP – Vapor duleAdditives: Gum Inhibitors, Metal Deactivators3-5NOTE: This RBOB may not be combined with any other RBOB except RBOB having the same requirementfor oxygenate type and amount.Dated: July 1, 2018Section 3-19
CODE 3U(1)Deliveries may be higher or lower by normal testing and handling tolerance. All tests shouldbe the most current version or the version specified by federal, state, or local government.(2)Mercaptan Sulfur waived if fuel is negative by doctor test.(3)This product shall be free from undissolved water, sediment or other foreign materials insuspension. See paragraph 3.1.8.(4)This product must be oxygenate free. Non hydrocarbon blending components are not allowed(5)Any Gasoline exhibiting an offensive odor and/or poses a personal health hazard and/orcontains more than 0.30 wt. % dicyclopentadiene will not be accepted for shipment(6)Refer to test methods published in 40 CFR Chapter 1, Part 80.46. ASTM methods D1319 andD4815 may be used in accordance with Federal and State laws.(7)Refer to test method published in 40 CFR, Part 80, Appendix E, Method 3.(8a)This product must be blended with 10% by volume Denatured Fuel Grade Ethanol.(8b)Federal RFG maximum and minimum testing requirement will apply to the final blends of thisproduct.(8c)This product, when blended with 10% volume percent of Denatured Fuel Grade Ethanol, andmust have a Benzene level of 1.3 volume % or lower and have an Oxygen content of at least1.7% but not more than 4.0% by wt.Dated: July 1, 2018Section 3-20
FUNGIBLE SPECIFICATIONSCODE 3XREFORMULATED PREMIUM GASOLINE BLENDSTOCK (PBOB)FOR BLENDING WITH 10% DENATURED FUEL ETHANOL(92% PURITY) AS DEFINED IN ASTM D4806NON-VOC-CONTROLLED COMPLEX MODEL PHASE IICHICAGO AREAThe following parameters apply before blending with denatured fuel ethanol:ASTM TESTSPECIFICATIONS (1)METHODPRODUCT PROPERTYMINIMUM MAXIMUMGravity, API @ 60 FD287, D1298, D4052ReportColorUndyedCorrosion (Cu) 3 Hrs. @ 122 FD1301Corrosion (Ag) 3 Hrs. @ 122 FD76711Gum, mg/100ml after washingD3814Gum, mg/100ml Negative (2)or: Mercaptan Sulfur wt. %D32270.002Oxidation Stability - MinutesD525240Appearance @ 70 F(3)Oxygen Content, wt. %D4815, D55990.05 (4)OdorNonoffensive(5)The following parameters apply after blending with denatured fuel ethanol:ASTM TESTSPECIFICATIONS (1)METHODPRODUCT PROPERTYMINIMUM MAXIMUMSulfur, (ppmwt)D2622, D5453, D703980Benzene, vol. %D36061.30Aromatics (vol %)D5769, D559950.0 (6)Olefins (vol %)D1319, D655025.0Oxygen, wt. %D4815, D55991.74.0 (7)E200 (vol %)D8630.070.0E300 (vol %)D8670.0100.0Octane:RON: MinimumMON: Minimum(R M)/2 (AKI):D2699D2700Volatility - Refer to Section 3Distillation - Refer to Section 3Drivability Index (Origin) – See “Documents & Forms” on Carrier’swebsite: www.expl.com/pipeline/shipping/manualsReid Vapor Pressure – See “Documents & Forms” on Carrier’s tives: Gum Inhibitors, Metal DeactivatorsReportReport93.0 (8)Page # or Doc Name3-33-3RVP – Drive IndexRVP – Vapor PressureSchedule3-5NOTE: This RBOB may not be combined with any other RBOB except RBOB having the same requirementfor oxygenate type and amount.Dated: July 1, 2018Section 3-21
CODE 3X(1)Deliveries may be higher or lower by normal testing and handling tolerance. All tests shouldbe the most current version or the version specified by federal, state, or local government.(2)Mercaptan Sulfur waived if fuel is negative by doctor test.(3)This product shall be free from undissolve
Jul 01, 2018 · Saybolt Color D156 20 Olefins Vol % D5443 .51 Oxygenates wt.ppm D6729 D4815 100 Paraffins Vol % D5443 90 Naphthenes Vol % D5443 report Aromatics Vol % D5443 2 Organic Chlorides wt.ppm D4929 1.0 Isobutane Vol % D6730 0.70 n-Butane Vol % D6730 03.0 Extract water pH D2110 report .
Robert Shapiro B ENEVOLENT M AGIC & L IVING P RAYER R OBERT S HAPIRO LIGHT TECHNOLOGY . Explorer Race series The Explorer Race ETs and the Explorer Race Explorer Race: Origins and the Next 50 Years Explorer Race: Creators and Friends Explorer Race: Particle Personalities The Explorer Race and Beyond Explorer Race: The Council of Creators
56-3 FireSIGHT System User Guide Chapter 56 Using the Context Explorer Understanding the Context Explorer † Understanding the Files Information Section, page 56-24 † Understanding the Geolocation Information Section, page 56-31 † Understanding the URL Information Section, page 56-34 For information on how to configure the Context Explorer as a whole, see the following topics:
Concept of Certificate of Origin (CO) Certificate of Origin (CO) is a document to prove the origin of a product. There are two (2) types of Certificate of Origin (CO): Preferential Certificate of Origin (PCO) Issued by MITI: Based on the requirements under the FTAs; and To exporters for their importers to enjoy tariff concession.
SAP Business Explorer i About the Tutorial SAP Business Explorer (BEx) provides you the set of tools to perform reporting, query analysis and to support strategic decisions. It is a complete product which provides different reporting procedures and an analysis tool to run queries and reports with SAP NetWeaver BI System. You can also use Business Explorer to broadcast the objects created under .
Grade Three History and Social Science Review Cards Page 7 of 19 What is an explorer? new discoveries 3 a person who travels seeking 3 What country sponsored the explorer, Christopher Columbus? 3 Spain What country sponsored the explorer, Juan Ponce de Leon? 3 Spain 3 What country sponsored the explorer, Jacques Cartier? 3 France 3
In this paper, the ES File Explorer App instructions have the following topics: Downloading and installing the ES File Explorer Ap p Connecting to a Thecus NAS via FT P ES Explorer file uploading and downloading instructions Uploading a file to a cloud service (ex. Dropbox / Google Drive)
SAP UX Explorer to SAP Enterprise Architecture Explorer SAP Enterprise Architecture Explorer is a self-service provided by SAP that provides answers to many of your enterprise-related questions. It provides a well-structured and easy
HSBC Bank International Expat Explorer Survey 2009 Methodology About Expat Explorer The Expat Explorer survey, now in its second year, is the largest global survey of expats. Commissioned by HSBC Bank International and conducted by third party research company FreshMinds, more than 3,10
