Peerless Performance TS-590S - :: Kenwood Middle East
Peerless PerformanceTS -590 SHF/ 50 MHz ALL MODE TRANSCEIVER
Discovering the HiddenThe TS-590S marks a bold new chapter in Kenwood’s proud off-frequency interferencevhistory of high-performance HF transceivers. Featuring a 500 Hz / 2.7 kHz Roofing Filter 32-bit floating point DSP 100 W heavy-duty design Automatic antenna tuner USB port for PC connectivitynarrow-band Roofing Filter, it significantly reduces interferencefrom unwanted signals, resulting in excellent RX performanceand revealing signals that would be hidden to lesser rigs.With IF AGC based on advanced DSP technology, Kenwood hasessentially redefined HF performance.Built to satisfy the most demanding DX’er, this high-performanceHF transceiver takes Amateur Radio to the next level andcontinues the Kenwood tradition of operating ease and ruggedreliability.2 TS-590S HF / 50 MHz ALL MODE TRANSCEIVERBest dynamic range in its class versus
Superb RX Performance: ExcellentDynamic Range Even with PowerfulOff-frequency Interference!Thanks to a narrow-band Roofing Filter and dedicated 1stMixer, this new transceiver offers the best dynamic rangein its class to handle adjacent unwanted signals.Reciprocal MixingTo measure the level ofreciprocal mixing, an off-channelsignal is mixed with the outputof a signal generator, which isthen varied until the unwanted signalcan be detected as noise. The higherthe figure, the less noise will begenerated by adjacent interference,allowing undisturbed reception.Powerful 500 Hz / 2.7 kHz Roofing FilterOn the 15, 20, 40, 80 or 160 meter band, the TS-590S employsdown conversion* for the first IF (11.374 MHz). Having the 1stRoofing Filter (6 kHz BW) directly after the Mixer enhances thenoise blanker’s ability to deal with adjacent off-frequency signals.What really determines RX performance is the 2nd Roofing Filter,after the post amplifier. The TS-590S comes equipped with a500 Hz and 2.7 KHz BW 6-pole MCF. This results in superbdynamic range when adjacent signals are present, performancethat was not previously possible using up conversion. So evenwhen an interfering signalapproaches the targetfrequency, a virtually flatdynamic range is maintained.Even with strong adjacentinterference, you can capturea clear signal.*For 1.8/3.5/7/14/21 MHz Amateur bands, when receiving in CW/FSK/SSB modesdown conversion is selected automatically if the final passband is 2.7 kHz or less.AD9951 from Analog Devices, IncWide Range of Features Thanks to32-bit Floating-point DSPIn addition to basic functions such as AGC, digital IFfilters, detection and demodulation, a wide range offeatures including noise reduction and IF notch are allimplemented with the latest algorithms.Advanced AGC with digital signal processing fromthe IF stage onwardThe TS-590S employs DSP from the IF stage onward. Kenwoodwas the first to offer DSP-based IF AGC in an Amateur radio(TS-870) and this DSP technology has been further enhancedfor the TS-590S, resulting in the development of a uniqueapproach to IF AGC. It is possible to apply level-optimised AGCeven for signals that slip between the Roofing Filter and the finalIF passband. You can be confident of optimum operation at alltimes, without having to think about the Roofing Filter bandwidth.Gain control performance has been greatly improved for the targetsignal in the final IF passband (RX band). This results in in-bandIMD (intermodulation distortion)characteristics on a par with thoseof top-of-the-line transceivers. Youcan enjoy superb RX with nextgeneration Kenwood sound.Texas Instruments TMS320C6726BDDS offers superb Carrier to Noise ratiocharacteristics, significantly cutting noise generatedby adjacent unwanted signalsFor the 1st local oscillator frequency, instead of employingconventional PLL/VCO, the output of a DDS (Direct DigitalSynthesiser) is supplied directly to the following Mixer. Whendown conversion is active, the oscillator frequency is lower thanit is with up conversion, so the output boasts even better C/N(Carrier to Noise ratio) characteristics and a desirable level ofreciprocal mixing.TS-590S HF / 50 MHz ALL MODE TRANSCEIVER 3
IF auto-notch* & manual notch**Both automatic and manual notch are implemented at the IFstage. By removing a powerful interfering signal with a notch filter,you can capture a weak target signal. With the IF auto-notch,notch frequency automatically tracks the beat frequency. Thenotch filter has such sharp characteristics that it is not possibleto adjust it manually. Manual IF Auto Notchnotch, however, offers notonly manual adjustment of thenotch frequency, but also thechoice of either normal or wideattenuation to suit the type ofinterference being encountered.*Available only in SSB mode.**Available in SSB/CW/FSK modes.Extensive interference/noise removal features Adjustable IF filter passbandBy adjusting the DSP filter passband, you can tailor interferenceremoval to suit your needs. This provides slope tuning in SSB/AM/FM modes, and bandwidth width/shift control for CW/FSK/SSB-DATA modes. Slope TuneBy adjusting HI/LOW cut, it is possible toavoid interference on one or both sidesof the target signal. SHIFT WIDTHIf the interference is on one side only,you can shift the central frequencywithout changing bandwidth.You can also avoid an adjacent unwantedsignal by narrowing the passband. Analogue & Digital noise blanking (NB1 / NB2)In addition to the analogue noise blanker (NB1), which has aproven track record for eliminating weak noise, this transceiveris equipped with a newly developed digital noise blanker (NB2).Just pick the blanker which is more effective for the type of noiseencountered and the RX conditions. NB1 offers stable noisesuppression independent of RX bandwidth because, during downconversion, the noise that has passed through the 1st RoofingFilter (NB filter) is fed to the NB circuit. The NB2 employs a newlydeveloped envelope tracking method, making it effective againstnoise that defies tracking by an analogue noise blanker. DSP noise reduction (NR1 / NR2)In addition to conventional NR1 and NR2, NR1 now employs anewly developed spectral-subtraction approach that is speciallydesigned to remove noise in speech modes. The optimum noisereduction method is applied for each RX mode. NR1Options and defaults for each mode (default settings in bold)SSB modeLOW CUT: 0, 50, 100, 200, 300, 400, 500, 600, 700, 800, 900, 1000 HzHI CUT: 1.0, 1.2, 1.4, 1.6, 1.8, 2.0, 2.2, 2.4, 2.6, 2.8, 3.0, 3.4, 4.0, 5.0 kHzCW modeWIDTH: 50, 80, 100, 150, 200, 250, 300, 400, 500, 600, 1000, 1500, 2000, 2500 HzSHIFT: 300 Hz to 1 kHz (50 Hz steps)SSB-DATA modeWIDTH: 50, 80, 100, 150, 200, 250, 300, 400, 500, 600, 1000, 1500, 2000, 2500 HzSHIFT: 1000, 1100, 1200, 1300, 1400, 1500, 1600, 1700, 1800, 1900, 2000, 2100, 2210 HzAM mode (AF filter for LOW cut)LOW CUT: 0, 100, 200, 300 HzHI CUT: 2.5, 3.0, 4.0, 5.0 kHzFSK modeWIDTH: 250, 500, 1000, 1500 HzFM mode (AF filter)LOW CUT : 0, 50, 100, 200, 300, 400, 500, 600, 700, 800, 900, 1000 HzHI CUTSpectral-subtraction noise reduction has been developed with afocus on improving speech clarity for weak SSB signals. Thanksto this advanced technology, which makes use of the processingpower of the 32-bit floating-point DSP, you can capture a targetsignal that is swamped by Noise Reductionnoise, without suffering anyNR1: Noise level is estimated and thatloss in quality. For the nonalone is subtracted, thus emphasisingthe target signal.speech modes (CW/FSK),a line enhancer offers triedand true noise reduction.Whichever method is used, thedegree of attenuation can beadjusted smoothly.: 1.0, 1.2, 1.4, 1.6, 1.8, 2.0, 2.2, 2.4, 2.6, 2.8, 3.0, 3.4, 4.0, 5.0 kHz Simple IF filter A/B switchingYou can, for example, set Filter Afor a wide passband, and FilterB for a narrow passband. Whensearching for a particular stationduring CW operations you canthen use the Filter A, switchingto the narrower Filter B once communications are initiated. In thisway, you can easily switch between 2 preset DSP filters as needed.4 TS-590S HF / 50 MHz ALL MODE TRANSCEIVER NR2(SPAC)Kenwood’s original NR2 is SPAC-based noise reduction thatextracts a periodic signal. SPAC is ideal for CW operations as itcan suppress noise at the same frequency as the target signal.You can adjust correlation time in 2 ms increments from 2 ms to20 ms (10 steps). NR2 is not Noise Reductionavailable for FM.NR2 : SPAC
Beat cancel (BC1 / BC2) Optional TCXOWhereas IF auto notch is Beat Canceleffective against a single,Multiple beats can be cancelled.powerful beat, the beatcancel feature comes intoits own when there aremultiple, relatively weakbeats. Choose BC1 to removeweak and/or continuous beatinterference, and BC2 tohandle intermittent beat, like that of a CW signal. Since this canbe used in conjunction with IF auto notch, even more effectivebeat cancellation is possible. (SSB/AM/FM only)The TCXO (temperature compensated crystal oscillator), which isavailable as an option, ensures superb frequency stability ( 0.5ppm)throughout a wide temperature range, from -10 C to 50 C. Beat Cancel OFF Beat Cancel ON Drive output (including 135 kHz band)The DRV terminal provides external access to the TX driveoutput (approx. 0 dBm). This is not just handy when a transverteris attached: the main antenna terminal cannot be used fortransmission on the 135 kHz band, but this DRV terminal fills thatneed. Convenience is further enhanced when combined with thededicated RX antenna terminal.Note: A separate license may be required in order to use this product with suppliedequipment or to transmit on frequencies that the TS-590S is not compatible with. Speech processor (SSB/AM/FM)The speech processor enhances the clarity of messages for thereceiving station by raising average TX power. And as well asadjusting compression level, you can switch between soft andhard modes. Adjustable TX filter (SSB/AM)High-reliability TX Sectionfor a High-quality SignalKenwood’s attention to detail is evident in both TX andRX performance.Stable operation guaranteed. Designed forhigh reliability. 100 W heavy-duty designThe cooling system features a pair of 60 x 60 mm fans, the samesize as on the previous model. Having two fans provides sufficientair flow at low rpm, ensuring quiet operation. Meticulous attentionhas been paid not only to the fans and motors but also to thesize and shape of the intake/exhaust vents as a comprehensiveapproach to noise reduction. The aluminium die-cast chassisis combined with a large heat sink to enhance heat dissipationefficiency, minimising the rise intemperature in the final sectionduring continuous TX sessions.This heavy-duty design iscapable of withstanding longhours of operation undergruelling conditions typical ofcontests or DXpeditions. Built-in automatic antenna tuner(compatible with 5 MHz band)*The preset-type automatic antenna tuner enables quick bandchanging and can even operatewhen the TS-590S is receiving.When the TX frequencychanges, the requisite presetdata (stored separately foreach antenna band) is loadedinto the antenna tuner circuit toensure that optimum matchingis rapidly achieved withouthaving to retune.*UK onlyThe TX filter passband is switchable. Since the high-pass andlow-pass cut-off frequencies can be switched independently, youcan have fine control over filter operation. TX equaliser (SSB/AM/FM)The equaliser offers flat (default), high boost (2 types), Formantpass (to minimise extraneous sounds), bass boost (2 types),conventional and user settings (using the ARCP-590). It ispossible to adjust frequency characteristics to suit the voicequality and microphone characteristics on the transmitting end. TX monitorThis outputs the TX audio via the speaker allowing you to checkyour own sound quality. Other TX features VOX function (adjustable gain, selectable delay time) AdjustableTX power output Adjustable MIC gain Adjustable CAR levelExtensive CW Support CW auto tuneWith just the press of a button, you can automatically zero in on atarget frequency for CW reception. During RIT operations, it willalso tune in to the RIT frequency. 2 key terminals on rear panelThanks to both an electronic keyer (built-in) paddle terminal anda separate one for an external keyer, PC keying is possible evenwhen a paddle is connected. Other CW features Support for full break-in and semi break-in (semi break-in delaytime: 50 ms 1000 ms) Memory keyer (max. 4-channel messagememory) Pitch control (300 1000 Hz) Side tone monitor with10-step volume control Electronic keyer (selectable key speed,squeeze A/B modes) Microphone paddle mode CW reversemode CW auto transmit (in SSB mode, a simple key-press willswitch automatically to CW)TS-590S HF / 50 MHz ALL MODE TRANSCEIVER 5
Direct frequency entry, direct band selectionThe keypad is used for Amateurband direct key access. There are3 memories for each band, so youcan quickly call up the frequenciesyou usually use. Also, the buttons– laid out to optimise ease ofoperation – provide responsivefeedback. USB connectivity for PC controlThanks to the addition of a USB port, the TS-590S can behooked up to a PC with a USB cable, enabling PC control of thetransceiver plus TX/RX audio connectivity.Note: Because of the theoretical latency of USB audio, it cannot be used forapplications that are affected by a time lag.Superior Ease of Operation Plus MoreEnjoyable TX/RX PerformanceThe user-friendly man-machine interface means youcan count on impeccable operation – under the gruellingconditions of a contest or a DXpedition.Numerous functions to assure easy operation User-friendly menus, outstanding operating easeThe TS-590S menus offer intuitiveaccess to numerous additionalfeatures. The combination of menuand arrow keys makes operationintuitive. Also, the menu modeis visible in the main area, whilethe sub area scrolls through therelevant guidance information. Large display with 2-colour LED backlightThe large display ensures outstanding visibility under allconditions. And you can select amber or green for the LEDbacklight. Remote control of the TS-590S using a computerUsing the ARCP-590 radio controlprogram, it is possible to accessvirtually all functions from acomputer. This makes it easy foryou to change settings and managememory channels.*You can download related freeware from the Kenwood website after purchasing theTS-590S. Voice guide & storage unit (option)The VGS-1 voice guideand storage unit can servetwo important roles: vocalconfirmation (in English orJapanese) of frequency, keyoperation, settings, etc.,and recording/playback ofmessages received by thetransceiver.Voice memory: max. 4 channels(recording time: 30 secs each for CH1 & CH2, 15 secs each for CH3 & CH4) Constant RX recording: 30 secs (1 channel) External Connectors6 TS-590S HF / 50 MHz ALL MODE TRANSCEIVER
OFF beepOther featuresIn addition to conventional audio confirmation of operation, adifferent beep sounds when a feature or mode is off, allowingclear differentiation.RX RX equaliser Adjustable RF gain, adjustable AF gain, selectable SQL level ATT, pre-ampFSK Programmable function keys (PF A, PF B)The TS-590S features 2 programmable function keys. You are freeto select frequently used functions for assigning to these keys. Basic RTTY settings (keying polarity, shift width, high/low tones, reverse mode)FM FM Wide/Narrow switching for TX/RX FM signalling (CTCSS, cross-tone) Repeater subtoneDATA Independent SSB-DATA/FM-DATA modes Choice of IF filters for PSK31/AFSK operations Selectable DATA modulation line (ACC2/USB) Variable ANO/ANI level DATA VOXAccessory connectors Memory/Scan functions Easy-to-usememoryThe Memory Name function enables clear identification for upto 110 memory channels (including specified ranges). Also, thememory scroll function can be used to check memory channeldata without changing operating frequency. Other features includea Quick Memory function for storing frequencies on the fly (max.10channels),* memory channel copy, single channel memory clear,memory lockout, memory shift, and the ability to change memorychannel data/frequency temporarily.*3, 5 or 10 channels can be selected. ACC2 connector for packet operations Remote connector compatible with linear amp control(built-in vacuum tube linear amp control relay, selectable TX attack delay)External connectivity Kenwood Sky Command II support(when connected to TH-D72E) Packet cluster tune (when connected to TM-D710E/TH-D72E) Emergency contact frequency paging TX tuning for external antenna tunerPower-on messageNote: A message of up to 8 alphanumeric characters can be input for displaywhen the power is switched on.scan functionsIncluded among the many scan functions are program scan,memory scan, group scan, subtone scan and CTCSS scan. Anda program slow scan automatically reduces the scanning speedaround any frequency of special interest.Cross-band repeater functions (when connected to TM-D710E/TM-V71E)Others MultipleExternal antenna tuner ready (AT-300*) Split data transfer using COM port Firmware updates Adjustable long-keypress timing*Discontinued productsKenwood Sky Command System IIThe Kenwood Sky Command System (KSS) effectively puts an HFtransceiver in your hand, allowing you to relax in your lounge orbackyard while controlling the TS-590S in your shack. Or you couldbe sitting at a football game while operating the HF transceiversafely installed in your car. And the Kenwood Sky Command IIadds the convenience of LCD confirmation of HF frequency.It’s not just freedom you’ll enjoy: KSS is simple and intuitive,yet amazingly powerful. Once the Transporter (TH-D72E orTM-D710E)* has been wired to your TS-590S HF transceiver,all you need to carry is the second Commander (TH-D72E orTM-D710E). The Commander transmits control signals to theTransporter, which also relays your voice to the HF radio. Inreturn, HF signals are transmitted back to the Commander.This system allows you to transmit and receive HF signals, setfrequencies, switch memory channels, and much more — fromyour handheld or mobile transceiver. Kenwood Sky Command IIKenwood Sky Command II utilises full-duplex operation, addingsome extra features that further enhance functionality. For example,you can confirm HF frequency visually on the LCD panel of theCommander. Control is effected via TNC (AX.25), and now evenmore HF functions are accessible: XIT, mode switching (USB,FM, etc.), split-frequency operations on/off, memory shift, andfrequency step selection. In addition, once every 10 minutes, theTransporter will send out its pre-programmed call sign via CW.*Kenwood Sky Command II uses a pair of TH-D72E or TM-D710E transceivers.Commander (CMD)Transporter (TRP)430 MHz/144 MHz (2M)430 MHz/144 MHz (2M)HF antennaCOM connectorMICorTM-D710ETH-D72EorTM-D710Eø3.5 EXT SPTH-D72EHF TransceiverTS-590S430 MHz bandVoice signals, Control signals430 MHz bandConfirmation of HF frequency144 MHz bandHF receive audio The operator controls the TS-590S HF transceiver from the Commander (CMD)TH-D72E or TM-D710E. Voice is transmitted from the CMD unit on the 430MHz band. Control signals are sent from the CMD unit on the 430MHz band. The received HF signal is re-transmitted by the Transporter (TRP) TH-D72E orTM-D710E on the 2M band. The operator can confirm the HF frequency on the LCD of the CMD.Note: Refer to applicable Amateur Radio regulations to check whether you are permitted to usethis function.TS-590S HF / 50 MHz ALL MODE TRANSCEIVER 7
ktopMicrophoneHandMicrophoneDC Cable(7 metres)MobileBracketExternalSpeakerRadio ControlProgram(available free for downloadingfrom the Kenwood onesTCXOHeavy-dutyPower Supply(22.5A)ARHP-590Radio Low-pass Filter(50 MHz bandis not supported)SP-50BVGS-1MobileSpeakerVoice Guide &Storage Unit(available free for downloadingfrom the Kenwood website)Not all accessories may be available. Please contact dealers for details.Main SpecificationsTS-590STS-590SReceiver (Continued)GeneralFrequency RangeTXRXMode160,80,60*1,40,30,20,17,15,12,10, 6 meter bands0.13 30 MHz, 50 54 MHz(VFO: Continuous 30 kHz 60 MHz)SensitivitySSB/CW/FSK (S/N 10dB)Less than 0.5 µV (0.13-0.522 MHz)Less than 4 µV (0.522 - 1.705 MHz)Less than 0.2µV (1.705 - 24.5 MHz)Less than 0.13 µV (24.5 - 30MHz)Less than 0.13 µV (50 - 54 MHz)J3E(SSB), A1A(CW), A3E(AM), F3E(FM), F1B(FSK)Frequency Stabilitys 5 ppm ( 0.5 ppm with SO-3), -10 C 50 CAntenna Impedance50 ΩAntenna Tunable Range16.7 150ΩSupply Voltage13.8 V DC 15 %Current DrainTXRX (No signal)20.5 A or less1.5 A or lessOperating Temperature-10 C 50 CDimensions(W x H x D)270 96 291 mm280 x 107 x 335 mmWithout projectionsWith projectionsWeight (Net)AM (S/N 10 dB)Less than 6.3 µV (0.13-0.522 MHz)Less than 31.6µV (0.522 - 1.705 MHz)Less than 2µV (1.705 - 24.5 MHz)Less than 1.3 µV (24.5 - 30 MHz)Less than 1.3 µV (50 - 54 MHz)FM (12dB SINAD)Less than 0.22µV (28 - 30 MHz)Less than 0.22µV (50 - 54 MHz)Squelch SensitivitySSB/CW/FSK/AM7.4 kgTransmitterOutput PowerLess than 5.6 µV (0.13 - 0.522 MHz)Less than 18 µV (0.522 - 1.705 MHz)Less than 1.8 µV (1.705 - 30 MHz)Less than 1.1µV (50 - 54 MHz)Max 100 W, Min 5 WAM: Max 25 W / Min 5 WModulationSSBFMAMBalanced modulationReactance modulationLow-power modulationMaximum FrequencyDeviation (FM)Less than 5 kHz (Wide)Less than 2.5 kHz (Narrow)Spurious Response1.7 40MHz: Less than -50 dB40 MHz or more: Less than -60dBCarrier SuppressionMore than 50 dBUnwanted SidebandSuppressionMore than 50 dBTransmit Frequency Response-6 dB: 400 Hz 2,600 HzMicrophone Impedance600ΩXIT Variable Range 9.999 kHzFMLess than 0.2µV (28 - 30 MHz)Less than 0.2µV (50 - 54 MHz)Image Rejection RatioMore than 70 dBIF Rejection RatioMore than 70 dBSelectivitySSBCW/FSKMore than 500 Hz (-6 dB)Less than 1.2kHz (-60 dB)AMMore than 6 kHz (-6 dB)Less than 12kHz (-50 dB)FMMore than 12kHz (-6 dB)Less than 25 kHz (-50 dB)ReceiverCircuitryIntermediate Frequency1st IF2nd IF3rd IFDouble or 74 MHz24 kHz-73.095 MHz10.695 MHz24 kHz (except FM) /455 kHz (FM)*1 UK only*2 In 1.8 / 3.5 / 7 / 14 / 21 MHz Amateur band, IF band width 2.7 kHz or less (SSB, CW, FSK)*3 Except in 1.8 / 3.5 / 7 / 14 / 21 MHz Amateur band, IF band width 2.7 kHz or less (SSB, CW, FSK)More than 2.2kHz (-6 dB)Less than 4.4 kHz (-60 dB)RIT Variable Range 9.999 kHzNotch Filter AttenuationAutoManualMore than 60dBMore than 70dBBeat Cancel AttenuationMore than 40 dBAudio Output PowerMore than 1.5 W (8 Ω)Audio Output Impedance8ΩThese specifications are guaranteed for Amateur Bands only.Kenwood follows a policy of continuous advancement in development.For this reason, specifications may be changed without TS590S V3CA308E-E-8
Mar 02, 2018 · The TS-590S employs DSP from the IF stage onward. Kenwood was the fi rst to offer DSP-based IF AGC in an Amateur radio (TS-870) and this DSP technology has been further enhanced for the TS-590S, resulting in the development of a unique approa
How To Connect the Kenwood TS-590S to the SDR-IQ Receiver by Ian Wade, G3NRW g3nrw-radio@ntlworld.com Version 1.0 2 September 2011 Introduction These brief notes explain how to connect the Kenwood TS-590S transceiver to an RFSPACE SDR-IQ software defined radio receiver. This lets y
The TS-590S employs DSP from the IF stage onward. Kenwood was the fi rst to offer DSP-based IF AGC in an Amateur radio (TS-870) and this DSP technology has been further enhanced for the TS-590S, resulting in the development of a unique approa
Kenwood TS-590S. The Kenwood TS-590S is the exciter to my Tokyo Hy-power 1.5. Every once in a while my THP will "kick out" during a QSO with the Overdrive light coming on during transmit. So basically I
Peerless Black Peerless Black 2000 Oil-Less Peerless Black 2500 Direct Drive After many years of consulting the Australian market we have designed and developed the Peerless Black Range. From our slow revving Oil less pump at 1350RPM through to our slow revving Alloy pump they p
Kenwood TS-590S HF and 6 Meter Transceiver It is easy to set up and start making QSOs. Only three connections are required: power . May 2011), ) and . 5
The Peerless Pump Fire Pump Units and Enclosed Packaged Systems Thousands of Peerless Pump installations (UL, ULC or FM approved) deliver superior fire protection to facilities worldwide. For over eighty years Peerless Pump has been offering complete service, from engineering assistance to in-house fabrication to field start-up.
The Peerless Pump Fire Pump Units and Enclosed Packaged Systems Thousands of Peerless Pump installations (UL, ULC or FM approved) deliver superior fire protection to facilities worldwide. For over eighty years Peerless Pump has been offering complete service, from engineering assistance to in-house fabrication to field start-up.
Section 501 SECTION 501 5-3 1 2 LIME-TREATED SOIL 3 501-1 DESCRIPTION 4 Perform the work covered by this section including, but not limited to, treating the subgrade, 5 embankment, natural ground or existing pavement structure by adding water and lime in the 6 form specified herein, mixing, shaping, compacting and finishing the mixture to the required 7 density. Prepare the soil layer to be .
